I just bought an Airport Extreme and try to put in place. I have Fios cable with a router. I can not get anything except a blinking orange light. After reading the instructions, it seems that the problem with the ethernet cable but I
Must not exceed the flashing orange light. have tried three ethernet cables to the Fios router. All thoughts
What extreme version do you have?
Test the cables connecting the airport to your Mac with them and see if the ethernet works on Mac. Green connectivity light should go... If it fails, then the AE died.
Please do a factory reset, then try again.
Sometimes Mac airport utility works well... If you have the preference or iphone ipad, download and use iOS version airport utility and try it for configuration... It is much less awkward.
Tags: Wireless
Similar Questions
-
I just bought a refurbished Airport Extreme and I intend to use it as my router & combine with our old time Capsule of existing one to create a roaming Wifi network.
The new Airport Extreme (renovated) is in my studio/Office - directly connected to our internet broadband wireless (WAN port)
Our small ethernet is connected to my iMac [mid 2010 running OSX 10.11.5] & a PC and extends up to 2 other domains through an ethernet switch.
This configuration works very well, our internet speed has improved slightly - better than our old T-Link router bit. WiFi available throughout the House - better on one side.
Time Capsule (2 TB) is connected by ethernet on the far side of the House, offer backup Time Machine and strong Wifi to this area.
This time Capsule was an existing installation that went perfectly with the T-Link before I bought the Airport Extreme.
I used the Airport utility to set everything up and it seems to work.
The problem is:
Combines the Capsule and extreme connected & active, the Internet gradually slows down and grinds to stop. -Wifi seems to follow suit, but is much more gradual.
If I disable the Time Capsule, the internet connection is back to normal, Airport Extreme Wifi signal is strong and extends to almost all areas.
I got to the departure of the two units configuration problems, so I reset both factory default and from that moment managed to do all this work - with the exception that the internet connection slows down. Whenever I visit a different web site, it takes more time to load/link upward.
I spoke with our ISP, the link to our tower is solid. The technology suggested that I put Wifi on each unit to use a different channel (2 frequencies & several channels each available).
So far, this has not resolved the problem, I will continue to make adjustments.
I googled this - most of the answers are not to date - usually 2012, 13, 14. and not directly related to my situation. But I will continue my search.
I'd appreciate if anyone here has any suggestions
The new Airport Extreme (renovated) is in my studio/Office - directly connected to our internet broadband wireless (WAN port)
What is the number and the model of the modem or modem/router that your ISP has provided you?
Should we assume that you use a Mac with the help of a current or recent operating system?
If you get out of the Capsule of time and leaves disabled for now, the network AirPort Extreme continue to run at full speed for a few hours and not slow down?
We ask these questions because we must first confirm that the AirPort Extreme works properly until we can begin to troubleshoot the connection to Time Capsule.
-
I just bought 14 elements Photoshop and Photoshop first 14 for Mac (I have an iMac OSX) and downloaded and received periodic publications related to them. But try to install it after you type the serial number, I get the message that Adobe is unable to validate the serial number. I was chatting with the support of Adobes cat, who recommended to download the two files-dog again, but with the same bad result. Can someone help me?
(1) right click on the Finder on dock icon and select the option "Go - To Folder."
(2) you will get a text box, type in below mentioned command and then press 'return './ etc
(3) it will open the etc folder, look for file named "hosts" and the same screenshot of office.
(4) double click on the Hosts file, it will open it with TextEdit.
Let me know if you see any Adobe related as entries in the Hosts file 127.0.0.1 activate.adobe.com... etc?
-
How to increase the font size to the bridge using windows 7 and a k 4 monitor? It seems that this problem has come up before, but there is no answer.
For Windows, you can try this:
Adobe App scaling on the screens to high-resolution (FIX) | Dan Antonielli
-
I have acidently deleted my eviroment. now I can not install anything or change my settings in my control panel. Msconfig does not work. Cannot change network settings. This is the messege I get: the system cannot find the environment that was entered
Hi kotipelto.
To better understand the issue, we need the following information:
Are what environment you referring? What did you delete?
Let us know if you can start the computer in safe mode and works as expected.
Access the menu advanced startup options by turning on your computer and pressing the F8 key before Windows starts. Boot advanced options, select the menu safe mode.
http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode
If you can start the computer in safe mode, perform the system restore.
System Restore: System Restore to put the computer's system files to an earlier point in time.
Search the steps mentioned in the link below:
http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-sytem-restoreThank you, and in what concerns:
Ajay K
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.
-
Can only use safe mode and can not access anything except firefox
Basically, there are a few days all of a sudden, a box came up saying Windows Explorer has stopped working. No matter what I click, it returns constantly to the rear. Because I use firefox, I can't to anything except this, and I can't get him if I use safe mode.
It is terribly annoying, I have 6000 + photos and other things I need, i.e. duties.
How can I fix? I can't use the normal mode, and it's annoying.
Thanks in advance.Then download your data either by:
1 remove the drive and put it in a box of USB drive or use a USB adapter. Attach it to a computer that is running a working XP/Vista/Windows7 installation. Use the work of Windows Explorer to copy the data to the hard drive of the system to the rescue and burn data on cd or dvd. I prefer not to do it if I know the drive is infected because he has a chance to infect your host system. In these cases, I use #2 below.
2. you can start the target computer with a Bart PE (if you use XP) or a Linux live CD like Knoppix and retrieve the data in this way. General information about the use of Knoppix for this are:
You will need a computer with two cd records, one of which is an engraver of CD/DVD OR a USB thumb drive with sufficient capacity to store your data, OR an external hard drive formatted USB FAT32 (not NTFS) *. Download Knoppix .iso image file and create your bootable CD. If you do this in a previous (XP or Vista) operating system, you will need the third burning like Nero, Roxio or the free ImgBurn software (Windows 7 can burn .isos natively). Burn as an image, not in the form of data. Then boot with the CD that you created, and Knoppix will be able to see the files in Windows. If you use the USB key or an external hard disk, right-click on its icon (on the desktop) to get its properties and uncheck "read only". Then click on it to open it. Note that the mouse action by default in the window manager used by Knoppix (KDE) is a simple click to open instead of double-click traditional MS Windows. If you want to burn CD/DVDs, use the K3b program.
* My understanding is that you can now write on NTFS from Linux partition. If you wish to do this, Google for instructions on the use of the NTFS driver.
http://www.Knoppix.NET
http://www.nu2.nu/pebuilder/ - Bart PE BuilderThen do a restore clean factory/install of Windows.
I want to emphasize that you should not take what I wrote as a definitive diagnosis. I can't see or test your computer from here. I give you my opinion on your computer based on my experience as a computer tech and what you have written. If you can't do the work yourself (and there is no shame in admitting this isn't your cup of tea), take the machine to a professional computer repair shop (not your local equivalent of BigComputerStore/GeekSquad). MS - MVP - Elephant Boy computers - don't panic!
-
Can not get on PC Win7 SP1 10 app despite all the updates window.
Hi, I can't get 10 App window on my PC in Win7 SP1 despite all the updates. I ran the utility software troubleshooting GWA and he said that my PC is not up-to-date. I had followed all the instructions on the troubleshooting page. Under my computer properties, it shows that my Windows 7 is genuine and SP1. I can not find the service pack SP1 showing installed in my control panel in the installed updates. I tried to reinstall SP1, but it said I already had SP1. Following the instruction on the Windows 7 SP1 download page, I tried to uninstall the SP1 that is currently on my PC using the command-line option, but he says that I don't have SP1 installed. (So confused) Someone has the same problem and knows how to solve?
Look here:
http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-update/Windows-10-app-wont-appear/3ecd42e4-7553-4565-9fab-277d49c2d941?rtAction=1438305025262
-
Can not download anything "keep telling my Temp folder is read only in the properties.
So I change it then when I click on it. Its the same thing. I have disabled system restore. Mr. ran fix it. Nothing. I know I have something. But nothing is recovering. HELP PLEASE. Thank you
Hi billyweeks,
1. what Fixit did you run?
2. you remember to make changes to the computer before this problem?
You can read the following article and check if it helps:
You cannot view or change the read-only or the attributes of system files in Windows Server 2003, Windows XP, Windows Vista or Windows 7
http://support.Microsoft.com/kb/326549/en-us
Hope this information is useful.
-
Can not get my printer to load software or disks on the computer
I have a HP 6500 AIO and a dell XPS 8100 but I can't get my software on my computer and HP is not help.
I have an e709 not wireless.
-
If I do, all the drawings after the point where I want to insert the frame will be removed. If I leave the rate untouched, everything works fine.
Hi trickytriet74,
suggest you to refer to this link:
-
Even with the new download of Firefox asking Firefox as default browser to open Google becomes the browser open. Impossible to get "Firefox" to join the options to clear the cache.
Make sure that you run not Firefox mode full screen (press F11 or Fn + F11 to toggle; Mac: Command + SHIFT + F).
If you are in full screen view then hover over with the mouse to the top of the screen to facilitate the bar appear Navigation and tab bar.
Click the expand (in the top right Navigation bar) to exit full screen or right-click on a space empty on a toolbar and select "exit full screen" or press the F11 key.Make sure the toolbars like the toolbar 'Navigation' and the 'personal bar' are visible.
- Firefox menu button > Options
- View > toolbars (press F10 to display the menu bar)
- Right click on empty toolbar space
See also:
-
Original title: problems cannot do anything
Windows cannot access the specified device, path or file. You can't have__appropriate the permissions to access the item. I get it all the time can not download anything
Hi birdylod,
· What version of the operating system is installed on the computer?
· You did changes to the computer before the show?
· You use Internet Explorer? If so, what version are you using?
· What files you download?
Follow these methods.
Method 1: Performs a search using the Microsoft safety scanner.
http://www.Microsoft.com/security/scanner/en-us/default.aspx
Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.
Method 2: Follow these steps:
Step 1: Start the computer in safe mode with network and check if the problem persists.
Startup options (including safe mode)
http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode
Step 2: If the problem does not persist in safe mode with networking, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.
Note: After completing the steps in the clean boot troubleshooting, follow the link step 7 to return the computer to a Normal startupmode.
Method 3: Scan the file system (CFS) auditor to repair corrupted files.
How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7
http://support.Microsoft.com/kb/929833
For reference:
What to know before applying permissions to a file or folder
-
I just bought a new computer and I was wondering that if I were to do something like unistall Creative Cloud/PS and LR to my old model to the new model I'd appreciate any help (real) Thanx Jimi
Cloud license allows 2 activations http://www.adobe.com/legal/licenses-terms.html
-Install on a 2nd computer http://forums.adobe.com/thread/1452292?tstart=0
-Windows or Mac has no importance... 2 on the same operating system or 1 on each
-Two activations may NOT be used at the same time (noted in the link above of the license)
IF you won't use the old computer...
Remove the license on a computer http://forums.adobe.com/thread/1442423?tstart=0 can help
-read http://helpx.adobe.com/x-productkb/policy-pricing/error-maxium-acitvation-exceeded.html
-or https://helpx.adobe.com/x-productkb/policy-pricing/activate-deactivate-products.html
-
I just bought a new IMac and want to run my old version of Dreamweaver CC3 on that, but I'm getting this quickly, "to open Dreamweaver, you must install the runtime Java SE6 strives". How can I do this?
Download it here: Java for OS X 2015-001
-
I just bought the photography package, hoping that it would be more storage for backup, etc. in CC. And now I can not even find where to buy them more storage cloud, the 2gig won't be enough for me. Where can I buy more storage?
Currently, there is no option to purchase additional storage through the creative cloud.
Maybe you are looking for
-
Hi, I recently purchased a Qosmio G10 and noticed on the page drivers there are a lot of updates, a few go back to November last year. Do I need to install all of these updates to make my machine works best?
-
DVD - RAM drive means that I can burn DVDs & CDs on the Qosmio series F
Can someone tell me that if I see "DVD - RAM Drive" under my computer does it means that my laptop allows you to record CD and DVD?
-
Error message at startup "SQLite 3 has stopped working"
original title: problem with SQLite 3 After you restore my computer, I received the following message and don't know what I have to do: A problem with SQLite 3 SQLite 3 has stopped working properly. A newer version of this software is available for d
-
I can't open my emails to read. Why are not open my emails?
I can connect and everything. I can even sent an email, but my e-mail does not open. If I double click on it it will not open so that I can read... I hope b, now have no more problems open your email. I have the same problem now. Can you help me plea
-
In my product key for windows laptop family premium is faded, or it wasn't clear to read. I can offer this problem? SO I CAN'T ACTIVATE WINDOWS