I'm unable to connect to wireless modem, the message's problem is the network cable is unplugged got new cable still

Similar Questions

• Unable to connect to wireless networking

  My Toshiba laptop has been pre-installed with Windows 7 Home premium 64 - bit OS and it worked quite well with the BB wireless. However, the wireless internet was on and turned off in recent weeks, while other mobile devices, such as iphone, ipad, or laptop, in my household had no such problem. The wireless signal was so strong, but the error message always says "unable to connect to wireless networking. It seemed that there was something wrong with the wireless adapter.

  I got a new adapter properly installed TP-Link wireless. Fortunately, it worked; but unfortunately, it worked for less than 24 hours. It was really frustrating that I, like student full time, depended so much on the wireless network card.

  Help, please! Harry

  Hello

  You can enlighten us with:

  -What model do you use (eg..) L300-123)
  -What version of BIOS is installed?
  -WLAN driver do you use?

  All these questions are answered in PC Diagnostics are under Toshiba app folder in the start menu.

  BR

  Tom

• Unable to connect to wireless networks more. ("Windows could not connect to (SSID)")

  Hello!

  Something very strange is happening with my laptop (dv6-3060ee). Up to this day at noon, everything worked well, including the wireless network. So, I set my computer to Hibernate and came to the House of my parents. As I turn it on and try to connect to the wireless here, I can't. I get this error "Windows could not connect to (name of the network).

  I'm on W7 Home Premium 64-bit and the card wireless in an Atheros 9285 b/g/n (model number can be a problem, I have it does not properly check).

  Things to consider:

  -I don't know that this is not a router problem or hardware WiFi card because:

  1. I can connect to the router and get internet access on my phone and with the other computer normally.

  2. on the laptop, I can not connect to the network without wire inside W7, BUT with HP QuickWeb (this system of Opertaing before loading windows), I can normally connect to the network and access to internet.

  -Have you ever tried, without success:

  1 reinstall the driver for the wireless card / Unistalling the driver and install it again

  2. change the encryption on the router. (Even with no encryption I can't connect)

  3. of course, restarting the computer, turn off/on of the network card, reset the router

  So, I'm sure it's a problem with Windows. I did some research here and in other places and other people seem to have the same problem, but I couldn't find any solution.

  I didn't install any software today which could cause conflicts.

  So, can someone help me, please?

  Thank you

  Thank you for your help, but I'd already sorted.

  The problem was really the driver, an update had been installed by the HP update program and it makes the device stop working. This problematic driver was March, I can't remember the version number.

  I went to the Device Manager and pressed on "Roll Back Driver". Windows restored to an October/2009 driver, 8.0.0.238 version number, and now it works as it should.

• My MacBook froze during the installation of the update at El Capitan and now I am unable to connect to any except the screen of the guest user. There was a message of panic, and somewhere in there, he said no set of OS. I tried to start without danger, it

  My MacBook froze during the installation of the update at El Capitan and now I am unable to connect to any except the screen of the guest user. There was a message of panic, and somewhere in there, he said no set of OS. I tried to start without danger, it does not work either.

  This general situation may be similar to what is mentioned in this sequel to thread of the CSA

  and if the remedy is to use instructions; detailed and I hope they are correct...

  Re: Restart fails after installation of El Capitan help!

  Or you can try and see on the repair of the system and then if your disk utility can

  See the Macintosh HD, as a boot volume, you could restart from OS X Recovery to

  the Mac system, to see if this solves the problem. There may be more than one cause.

  You could try and boot into OS X Recovery, utilities out there, and other options are available.

  • OS X: on OS X Recovery - Apple Support

  This example uses a special partition on the hard drive of recovery which is not in the

  same disc that the Mac OS X section; However if your hard drive is missing, these other

  items may also be at risk. You must have and maintain backups of your duplicate content

  on the external storage drives closed; In addition, a Time Machine backup helps to restore.

  • Apple OS X and Time Machine tips:

  http://pondini.org/OSX/home.html

  • Tips for OS X - using HD recovery:

  http://pondini.org/OSX/RecoveryHD.html

  {Using the utility disc and other tools can be done from the boot OS X Recovery volume

  Beware of the fact these tools can also delete or reformat your content; wiping.}

  Don't know what to say; you could see visiting an Apple store with genius if

  There is an official store. Usually for best time planning you would contact them for an appointment.

  • Make an appointment at an Apple Retail Store Genius Bar
  • Find an Apple authorized service provider
  • https://locate.Apple.com/country - Apple - find places - selector of country (if outside the U.S.)

  Or if there is no official retail Apple Store with genius, the following suggestion would be to contact

  a service provider authorized Apple, an independent specialist who is qualified in the repair of Apple.

  In any case...

  Good luck & happy computing!

• Unable to connect when you use the router

  OK Ive been using my router for some time and it has always worked a few weeks ago, she decided to stop working, when im connect directly from computer to Internet modem is very good, so my cables and modem and all that is fine. When I connect everything through the router... Router, computer modem to the router, all the lights are show as normally its work, on the router and modem, the network on the computer thing Local didn't tell only / limited connectivity, rocking it back... but usually connectivity IPv4 said Limited instead of Internet

  Things I've tried:

  Unplug everything, turn it off wait 30 seconds... to deceive, dosent work

  Buy new cables just in case... it dosent work

  use LELA 1.6 to try and re-setup/installation/configuration of the router... says I don't have an internet connection

  updated LELA 3.0 or 3.2 I forgot what was it, and it does nothing

  tried to disable the network to try to turn it back on to see if it would help what whatsoever, and it the connection decides to disappear out of my zone connections network completely and then I don't have any internet at all the

  Usually I can solve a problem me when something goes whack with my net, but im lost and im hoping someone out there can help with my problem

  Reset the router...
  1. hold the reset for 30 seconds button.
  2. then disconnect the Dungeon can now hold the reset button for
  another 30 seconds.
  3. plug back in the power and keep the reset button pressed
  for 30 seconds.
  4. release the reset button.

  Then click here to re - configure your router...

• I'm unable to connect to a specific web site. Have you tried 3 different browsers and they all say that they are unable to connect. No one else has a problem connecting to the page.

  I tried to use www.findagrave.com for 2 days.  I tried 3 different browsers.  all say that they are unable to connect.  No one else has a problem on this page.  I have no problem to do something else.  Why, throughout this site I can not connect with?   I use it all the time in research.  very aggravating.

  original title: on a web page

  Well, I tried the support page, but I already tried all that.  I did a restore full back to factory settings... still cannot have only one page to load.  I'll call my dsl provider this afternoon.  I don't know what else to do.  I can't communicate with Findagrave.  I don't have a snail mail address but no phone number.  But I don't think that it would be them anyway, if no one else has a problem with this web site.  There must be on my end, don't you think?

  I don't know what to tell you. There is no problem, it's on your side.

  If you care to try it... on the assumption that your user account is damaged.
  Create a different user account with exactly the same type of account > connect to it and see if you can access this Web site.

  Personally, I doubt that will solve anything, since you already restored your computer to factory settings.

• Unable to connect to aol. The mistake of AOL bed AC - 3000 084100103

  Original title: program compatibility Application Applications App Apps game games Legacy Crash crashes Hang hangs

  I have a Windows Professional (Windows 7 6.1) on my new HP Pro Book 4525 s. I downloaded AOL 9.6 and unable to connect to aol. The mistake of AOL bed AC - 3000 084100103. How can I solve this problem?

  Hi Harry00700

  The error message seems to be accurate with the AOL servers. I suggest you to follow the links and check if it helps.

  http://Canada.AOL.com/help_files/canada_help9/Frequently_asked_Questions/What_if_I_cannot_connect_to_the_AOL_service.htm

  http://help.AOL.com/help/microsites/microsite.do?cmd=displayKC&docType=kc&externalId=222310

  If this is not enough, you can communicate with AOL.

  http://help.AOL.com/help/microsites/microsite.do

  Hope the helps of information.

• I need help installing Acrobat Reader - unable to connect to a DDE server messaged. Cannot access documents

  I need help installing Acrobat Reader - unable to connect to a DDE server messaged. Cannot access documents

  Please see if "acrobat could not connect to the dde Server" when openning Adobe Acrobat PRo XI help.

• "Limited connection" when you configure the network between two computers XP.

  Original title: Configuration of the network connection

  Trying to establish a network connection between two home PCs., both running Windows XP Pro. Have been through the network on both PC Setup Wizard but, they still say limited, in fact no connection. I use an Ethernet cable between the two Crusader. If it is true what I'm doing wrong?

  Thanx Terry

  Old but good, networking tips from MVP Malke, MS:

  The best and simplest is to buy a wireless router. This way you get Internet connectivity both machines and the added benefit of security more between you and the Internet. Then you configure your network wireless safely, and then you configure file/printer sharing. Here is information on the implementation of a router and also in networking. It seems long, but don't be intimidated. Setting up a router and the LAN of sharing between two computers takes about 15 minutes.

  The router configuration

  Setting up a router is simple enough. Normally, you run the CD that came with the router and follow the instructions. If you're running Vista, maybe the CD that came with the router does not work; I do not know this. But you can set up the router without the CD. Note that if you have Internet cable for the connection you have just set up the router to DHCP (or there may even be a choice of cable to choose). If you have DSL Internet, you select TRP usually and enter the username and password you selected when you initially set the DSL connection. So:

  1. turn off the power to your cable modem.

  2. attach a cable (usually supplied with the router) course Ethernet cat5e Internet/WAN port of the router to the Ethernet port on the cable modem.

  3. connect the ethernet cable cat5e from the network card in your computer to one of the ports on the router. If you do not have an ethernet cable (because you were using USB), you will need to go to the store and buy a.

  4. turn on the cable modem. After that all the lights are on, turn on the router.

  To configure the router:

   

  Have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

  http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

  This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine.

  Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

  Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar.

  Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). If you have a newish computer, you will be able to affect security WPA2-Personal Mode. Do this and enter a password. The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

  At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the Ethernet cable and wireless of the computer should see your new network. Enter the password you created to join the network and start surfing.

  *****

  B. file/printer sharing of

  Excellent, comprehensive, but easy to understand article on sharing files/printer under Vista. Contains information about sharing printers and files, and the folders:

  http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

  For XP, start by running the Network Setup Wizard the on all machines (see warning in section A below).

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, it means which allows file sharing / print on the Exceptions tab normally run the XP Network Setup Wizard will take care of this for these machines. The only "witch hunt", it will turn on the XPSP2 Windows Firewall. If you are not running a third-party firewall or you have an antivirus with "Internet Worm Protection" (like Norton 2006/07) which acts as a firewall, you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this. The instructions on this link work for XP and Vista:

  Set up Windows to automatically connect (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

  D. Si one or more of the computers is XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. XP Home does not share the users directory or the Program Files, but you can share folders inside those directories. A better choice is to simply use the Shared Documents folder. See the first link above for more information on Vista sharing.

  F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers, but it is outside this response.

• I can't connect you on some client computers on a domain environment unless I have remove the network cable.

  I have almost five machines on my LAN that cannot log on to the domain, unless I have remove the network cable and then it connects.
  Please advise?

  On the domain controller or problems by communicating with the domain controller, when you remove the network cable, you connect with that caching of credentials.  Also look at the DNS settings on the RODC, the RODC DNS should point to itself, make sure that the machines are all on the same subnet.

  John

• HP LJ CP5525 won't boot if the network cable is connected.

  Hello everyone, I have a client who brought me a CP5525 for repair with an unusual problem.  The machine will not get past the initialization stage if the network cable is connected.  If the network cable is removed, the machine comes to ready.  Initially, I suspected a trainer Board bad, but instead, I get the same problem.  With the network cable is connected, the machine will not get past the initialization stage.  I know I'm the cable is good I can plug another printer in there and it works fine.  The trainer has a green light on the port of the network adapter when the cable is connected, the led "smiley face" is on the balance and the "heartbeat" light flashes twice and pauses, then blinks twice again and continues to do so, that everything seems normal.  In addition, while the machine is still being initialized, I can press the test button on the print engine and it prints a test page to the normal search.  I don't know if I should just let the machine only and see if it boots never completely, but no idea how long I have to wait, I left longer than 10 minutes and it is not always initialize.  If I unplug the network cable and allow the machine to go ready I can print a log of events and it shows no errors.  Of course, it is used as a network printer, so there need to be ready with a NETWORK cable.  At this point I have no idea what my next step should be to help or ideas would be appreciated.

  I left the nic cable disconnected and allowed the printer to come ready.  Then, I plugged the network cable and tried to install the printer on my network local test.  I ping the printer and he answers, I can't install the printer normally, but it does not print a test page.  When he goes to print the test page the printer winds up as if she warms to print, but then rolls down.  Meanwhile, the port of the network card on the machine poster in green and yellow flashing as if it receives information of the network, but there is no change on the screen and the led lights on the front panel show no change.  Finally, the print job expires and shows that printing does not.  If I try to print from microsoft word or notepad saying, I get the same symptoms.  This happens with the new Council of trainer and the original one.

  Here in the building, we have an another CP5525 installed as a network printer that works very well, I went and printed its configuration and settings page and compared to the printer, I'm working on and they are identical, with the exception of IP addresses of course.  At this point, I have the printer pushed to the side until I can get some ideas of what we must look at the next and I worked on other printers and used this same nic cable to test these machines and they print very well so I know that the problem is related to this printer.  I just need some ideas of what we seek to the next.  I removed the back cover and looked for loose cables and so on.  These machines are newer than most of the equipment that I service so I don't have any spare part for them so I can't start just you order parts at random just to Exchange and see what happens, so if anyone has an idea, I would be very grateful.  The machine is out of warranty at this stage.  Apparently, he was never installed and was sitting on the shelf for the past two years and tried to install it a few weeks ago.

  Two points here. First you move the hard drive to the new trainers, so if the hard drive is the problem you can not say. You have to 'borrow' a hard drive to an another base printer if you have another of the same model. Second by assigning the same network address of the printer if there is a problem with the print server on the base or the driver you are using is bad no way to tell. As I said in my post, you need to isolate your network printer and need to load on a virgin machine where you use any driver laser jet color printer that is built into the operating system, such as the printer color laserjet 5500. My gut tells me the problem is with the network and using the crossover cable confirm this. The fact that the printer is ready and you can print without the cable connected network tells me this. Thing that you can do with the printer NOT connected to the network, ping the ip address. It is possible that some other piece of equipment on the network took somehow this ip address and causes all sorts of havoc with your problem.  Now regarding the update of the firmware.  I'm sure that you have a computer at home that does not restrict the usb port.  Just take a USB key to your computer at home and put a picture of the ORL file on the USB at home and bring to the office and just that insert the drive into the USB printers and turn on the printer and it should ask if you want to load the updated file.  Either way, which base?  I'm retired U.S. Army more than 20 years ago.

• Cisco AnyConnect VPN Client (connection attempt failed because the network or pc problem cisco)

  Hi all

  I am trying to connect to my Cisco AnyConnect VPN Client but everytime I try, I get an error (connection attempt failed because the network or pc problem cisco)

  Can anyone help me please with this.

  Thank you

  Zia

  What is the local firewall on your computer?

• Update Windows 7 pro (10 users) network January 1, 2013. Now, for more than 4 users connect an access across the network apps stop apparently. Any thoughts?

  Update Windows 7 pro (10 users) network January 1, 2013.

  Now, for more than 4 users connect an access across the network apps stop apparently.

  Any thoughts?

  Hello

  Your question is beyond the scope of these forums. Please ask your question in the following forum.

  Windows 7 networking:

  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

  Concerning

• Unable to connect TC after modem swap, although wifi works very well.

  Time Warner Cable send me a new modem. (Technicolor)

  It is installed, enabled, and and the wifi works through my Time Capsule (1 TB 802.11n).

  But the TC blinks yellow and is no longer available on my iMac (Yosemite 10.10.3, 3.2 GHz Intel Core i3, 4 GB 1333 MHz DDR3)

  I restarted the mac, the modem and the TC, repeatedly.

  I have not tried a reset on the TC...

  It is installed, enabled, and and the wifi works through my Time Capsule (1 TB 802.11n).

  The last piece of this... WiFi works through my TC... sorry this is not possible.

  I have not tried a reset on the TC...

  Transport CANADA must be plugged in by ethernet on the main modem. If it's a router. Then the TC must be filled.

  But regardless of how it works you can not remove the ethernet of the TC.

  Transport CANADA should also create a wireless network and the Mac must connect directly to the TC otherwise on Yosemite or the BONES later, it will be more reliable and disappear from the network.

  So reset the TC... no files are lost and re-do the installation.

• Unable to connect to wireless networks

  I was unable to connect to my wireless network. My network connection on my laptop is enabled and under properties, it says that it's maintenance correctly. However, under the command prompt it says that my ethernet adapter network connection is disconnected. I've alerted to check my connection because my wireless network list went from about 10 ads to 1. 1 on the list is a network installation of HP. I had not seen it. Any suggestions or tips to solve this problem?

  better to go to your vendor manufacturer's site and download the driver from there, if possible, otherwise will do you the needfull Sohail who was Khan network hardware professional VOTE A S HELP FULL IF this REALLY ŒUVRES HELP the OTHER FIND ANSWER FASTER