I put my cRIO 'DHCP' to 'local connection' and lost contact with her.

Similar Questions

• Local use and authentication AD with ACS 5.6

  I have an ACS 5.6 unit configured to use AD authentication for my default network access and rules. It works very well.

  I tried to implement some features, put them in a group and give only locally defined ACS to users access to these devices.

  Problem, after you have created the local accounts on ACS creates a group of local identity, and trying to authenticate with a camera, I always get "object not found in the identity store.

  Is there a way to have the hybrid authentication like that? How do we?

  Hi Colin,

  One thing that comes to mind is "sequence of identity store. Ensure that you have "internal users" listed in there otherwise that demand would never be mapped against the internal users.

  I also want to double check the source of identity under default device admin or any service that you created. Ensure that internal users.

  Take a look at the document below for more details on the identity store sequence.

  https://supportforums.Cisco.com/document/103901/ACS-5x-identity-store-se...

  Kind regards

  Kanwal

  Note: Please check if they are useful.

• My phone connects random screen activity when I am not in contact with her.

  My flame is super Ahmed suddenly. I can't really use it, which makes it more hard problems. He seems to think I'm dragging in the center of the screen constantly, even if I'm not in touch with her.

  I started having this problem with a previous flame, but I broke the screen and the problem was concentrated where the screen was more damaged. This time, the screen is fine.

  The problem is localized somewhat: if I open settings, Geolocation tilt begins to tip like crazy. If I hold down the power button, immediately turns the power on and off - those who are both on the same section of the screen.

  Any thoughts on how to fix this?

  For me it looks like a hardware problem. Make sure the screen is clean and try to restart the phone. If it is persistent, you may have to contact the manufacturer.

• has blown my hard drive put in another a download windows 10 and lost everything on fire fox

  How to make it all back

  Should I suppose that you were no backups on an external or in the cloud?

  Have you ever set up Firefox Sync service?

  Is it possible to read data from the old hard drive, for example, by using a cable or an external enclosure for USB drive?

• BlackBerry Smartphones trying to put in place 2007Contacts of MS Outlook and the calendar with my BB 8330

  I keep trying to set up my 8330 BB with Outlook 2007, but I get a runtime error "cannot find system in the file table.  Help, please! It drives me crazy.  I was able to add my Lotus Notes without problem.

  http://www.BlackBerry.com/BTSC/search.do?cmd=displayKC&docType=kc&externalId=KB15278&sliceId=1&docTy...

• Satellite L40 don't stop with power connected and is not in sleep mode

  Hello world. I hope someone can help me. Basically, there are two problems: one with judgment of the laptop (Satellite L40 - 17U (Vista 32 bit Home Premium SP1)) down when power is connected and the other with closing the lid and put it to sleep.

  1. in recent weeks, it all of a sudden won't stop, whenever power is connected. When it's on battery, it will stop. When the power is connected, and I try to stop, it seems that it closed down (all activity stops and the led goes off) for about 1 or 2 seconds, then it goes back.

  2. when I close the lid (all settings in Vista are set to put the laptop in a State of 'sleep' when the lid is closed), the laptop enters a State where it cannot be recovered by stopping by pressing the power button for 10 seconds to close completely. When closing the cover, only the battery LED continues to Flash orange (the way it should be), but apparently the laptop keeps consuming power, because when I restart later (first having to close as described above) tends to be quite an empty battery as it was before the next redΘmarrage it (like go from 100% to 65% in 30 minutes as "standby mode"). Also, when I open the cover, the other LEDS will on new (green), but nothing happens.
  After the restart first by pressing the power button for 10 seconds to close, I often get the message that Windows cannot be started and run the system repair.

  I just do a completely clean install with the product recovery CD (has not installed SP1 yet), updated to v1.90 BIOS, but the problem remains.

  I'm afraid that my only option will be to bring him away for a warranty repair, but knowing that these repairs can take weeks, I'd rather try a solution here could someone recommend me first. If you have any ideas, please let me know.

  Thank you
  Daniel Breslauer

  Hi guys

  Never had this problem on my laptop, but with regard to an other users here in the forum the BIOS might help solve such strange behavior for laptop
  To be honest the closed question is unclear for me I noticed a problem before on my laptop but the update of the BIOS helped.

  This is why I recommend update BIOS first.
  If the problem still appears, the ASP should take a look in the notebook.

  Good luck

• Wireless connectivity problems: Windows Vista displays connected to the internet with good signal, but cannot access the internet more than a few seconds.

  Hello

  Recently, I brought a Dell with Windows Vista and a Belkin Wireless adapter in my house somewhere else. The computer has never had problems connecting to wireless internet on the other networks, however since the move I was not able to access the internet. Sometimes the network shows only a local connection and not Internet and other times, the network has a strong signal, a network identified and even an internet connection, but when I open any browser, it is only able to load the Google homepage and I cannot navigate anywhere else. I turned off all firewalls and even uninstalled all 3rd party software protection. I checked all my browser settings and made sure they detect automatically the IP settings and proxy settings. In other words everything seems in good shape, but I still have no navigation capability. Any ideas?

  It turns out that I had to remove all the old Wireless USB software that had been used previously (there had been other versions of Belkin and Linksys). I then used the computer from my friend to download suitable driver on the Belkin site for the internet adapter USB I used and BAM.

• Horizon view connection and security server matching

  Hello friends,

  I need some clarification on security and the matching server connection. If I understand well earlier in login server and security versions matching is one-to-one.

  Is this same behavior on the Horizon 6 as well? I can read that we can connect several Security Server single instance to connect to the server. But the reverse is possible yet? What are the combinations is achievable or supported?

  Documentation centre for Horizon 6 version 6.1

  still one by one,

  If you need high availability just add another server of connection and pair it with another security server

• Can ping cRIO but unable to connect to the MAX

  I have a cRIO 9066 put in place on a local subnet. I think that all the software and drivers are correct. I have deployed my program and it works great except... When I add some optical converters of fibre in the mixture. Here is my system:

  PC--> cable ethernet--> ethernet switch-->--> cRIO ethernet cable * it works fine *.

  PC--> ethernet cable--> converter of fiber--> fiber--> ethernet switch (FPS)-->--> cRIO ethernet cable * unable to connect to MAX *.

  When I connect with ethernet cables all the way through, the ping time is<1ms ttl="" is="" 64.="" when="" i="" add="" the="" fiber="" converter,="" i="" can="" still="" ping="" the="" crio="" but="" ping="" time="" goes="" to="" ~250ms="" and="" ttl="" goes="" to="" 247.="" then="" max="" can't="" connect="" to="" the="" crio.="" is="" my="" connection="" speed="" too="" slow="" for="" max="" or="" the="" crio="" to="">

  My converter fiber and ethernet sfp module switch are all 1000 MB/full duplex. It is run only on a 10 m fiber. I tried several fiber optic cables. I tried the sfp in several locations. My sfp and the switch are both Advantech so I guess that they are compatible with each other. At this point, I plan to buy just a card PCIe fiber for my PC, but I thought I should check first with the experts.

  Thank you

  Hello

  There is a timeout OR max. The default value is 4000 Ms the reason why you are not able to detect the cRIO in NOR-MAX may be because the packages are damaged along the way. If you do not want to check this, you can always monitor the packets with WireShark with two different sets high. In this way, you can see if the packets are defined correctly or not.

  I hope this helps!

• An error occurred while renewing interface wireless network connection: unable to contact your DHCP server. Request a expires.

  I use an Acer Asspire One with Windows XP. We have wireless through AT & T Uverse. The netbook has an Atheros AR5007EG Ethernet card.

  A number of things have taken place lately: I had not used the Acer for some time and the battery was dead and would not recharge. I could book until when it was plugged, but could not get on the Internet. I found online that the solution to the battery problem was to download a new bios that worked wonderfully and it is now loaded. Recently, our AT & T router died and was replaced. I put the new WEP keys in two other computers, and they connect to the Internet. I can't connect to the Internet with the Acer. I tried ipconfig / renew and get the error message: "an error occurred during renewal of the wireless network connection interface: unable to contact your DHCP server.» Request a expires. No operation can be performed on Local area connection while it has its media disconnected. "On the tab"Choose a wireless network", it shows my network and said"absorbing the network address"but nothing happens. When I do ipconfig I see that there is no IP address.
  I took the computer to Starbucks this morning, ran ipconfig / renew and she acquired the IP address and I was able to connect to the Internet. I brought the computer home and tried and failed to connect. The IP address is back to 0.0.0.0 and the error message appears when I try to renew it.
  I hesitate to make a lot of changes since it was working with a different network.
  Original title: IP address is missing
  These forums are wonderful. I tell myself that I've saved the cost of a new battery using the bios, I found on a forum!

  Hello

  DHCP - Dynamic Host Configuration Protocol is a protocol used by devices computer network (DHCP clients) that dynamically distributes the IP address of the destination host. Now the error indicates that your computer is not able to communicate with the server and assign the IP address.

  Method 1:

  Let us try to disable the firewall and check the issue.

  Note: Re-enable the firewall after checking the issue.

  Check whether the problem is resolved.

  Method 2:

  If the issue is not resolved, you can follow the steps from the link provided and check if that helps.

  How to reset the Protocol Internet (TCP/IP)

  http://support.Microsoft.com/kb/299357

  Hope this helps and let us know if you need more assistance.

• only local connectivity persists

  Always of the problems with the 'local only' connectivity with windows Vista. Have tried at least 3-4 different "fixes" but none of them work.

  I have ensured that 4 IPV is enabled and unchecked IPv 6.
  Can use the help by checking the properties and the following values:
  802.11n: 20 MHz only or 20 or 40 MHz channel width?
  802.11n mode: enabled or disabled?
  Ad Hoc channel 802.11 b/g: value 1 or 2 or 3 or 4 or 5 or 6 or 7 or 8 or 9 or 10 or 11?
  Ad Hoc default wireless mode: 0. 802. 11 b / g or 1. 802. 11A?
  Ad Hoc power management: disabled or enabled?
  Ad Hoc QoS mode: WMM disabled or active WMM?
  Mixed Protection CTS-to-self or RTS/CTS compatible mode?
  Roaming aggressiveness: 1. the lower or 2. Moderately low or 3. Medium, or 4. Medium-high or 5. Highest?
  Improvement of flow: on or off?
  Transmitting power: 1. the lower or 2. Moderately low or 3. Medium, or 4. Medium-high or 5. Highest
  Wireless mode: 1. 802. 11 or 2. 802 11 b or 3. 802.11 g 11 or 4. 802. 11 b / g or 5. 802. 11a / g or 6. 802.11a/b/g

  Hello

  Method 1
  I suggest you try the steps from the following link:

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article: back up the registry in Windows Vista

  Method 2
  In addition, you can disable IPv6 to see if that nor does not affect the wireless adapter.

  To disable IPv6:
  (a) go to start, right click on the network, and then click Properties.
  (b) network and sharing window will appear, then click on manage network connections.
  (c) network connections window will appear. Here you can right click on the network adapter that you want to disable IPv6, then click Properties.
  (d) in the local area network connection properties window, clear the Internet Protocol Version 6 (TCP/IPv6) check box, and then click OK.

• Need help with the data storage store, local array and network connections

  Need help with my ESXi 4.1 installation

  My hardware:

  I built a server with an Asus P6T whitebox, i7 920, 12 Gig RAM, NIC, Intel Pro1000 PT Quad, 3ware 9650SE-12ML with 8 1.5 TB SATA green in a raid 6 array gives me about 8 + TB with a spare drive all housed within a NORCO RPC-4220 4U Rackmount Server chassis.  I also have a 500 GB SATA drive which will hold the ESXi and virtual machines.

  The network includes a firewall, Netgear Prosafe FVS336G, GS724Tv of Netgear ProSafe 24 port Gigabit Managed Switch on a dhcp cable modem internet service provider.

  I also have 2 old NetGear SC101T NAS disks (4to) I want to connect to the system how some - at a later date have... data on them and want to transfer to the new storage array. I always looking into the question of whether they will work with ESXi 4.1, or I might have to only access it through Windows XP.

  My Situation:

  I have already installed ESXi 4.1 and vsphere client with no problems and it is connected to a dhcp cable internet service.  I've set up host via a dynamic DNS service name give me a static hostname on the internet.  I installed three machines to virtual OS successfully at the moment and now want to first start by creating a multimedia storage server which will use some of this new 8 TB array, then separate data storage for use with a web server small overhead storage and a backup.  It is a domestic installation.

  Help with the data store and network:

  I was doing some reading, because I'm new to this, and it looks like I'll probably want to set up my table via ESXi as a nfs disk format.  Now, the data store is usually in another physical box from what I understand, but I put my readers and ESXi all in the same box.  I'm not sure that the best way to put in place with grouped network cards, but I want to make this work.

  I understand that in ESXi 4.1 using iSCSi LUN must be less than 2 TB, but nfs - I should be able to add a bigger partition then 2 TB (for my multimedia) in nfs, right? or should I still add it separately as a separate 2 TB drives and then extend them to get the biggest space.

  Any suggestions or direct resources showing examples on how to actually add some parts of the table as data warehouses separate nfs.  I know that to go to the configuration tab, and then select Add to storage, and then select nfs. I have not my picture, but it's here that I don't know what to do because ESXi 4.1 system already has an address, should I put the same thing to the new data store array also (will it work?), and what should I use for the name of the folder and the store of data... just do something to the top.  I thought to later install Openfiler (for a multimedia storage using this table server) as a virtual machine, use the table with esxi so that I can access the same storage space with widows and linux-based systems.

  I also know I have to find a way to better use my quad nic card... put in place of virtual switches, grouping, etc HELP?

  Any direction, assistance, similar facilities to sample, suggestions or resources that would help would be great. I did a lot of hunting, but still a little confused on how to best to put in place.

  You must think of VMDK files of large databases with records of random size guest go read some data (a DLL or an INI file), maybe write some data back, then go read other data. Some files are tiny, but certain DLLs are several megabytes. It's random i/o all and heavy on the search time. IO Opsys is small random operations that are often sequential (go read data, write data, go read other data,...) so that deadlines are critical to the overall performance. That's why people say OPS are / s of reference and forget the MBs flow. The only time where you bulk transfers are when you read media (ISO files).

  Well, now forget all this. Actually the disk activity will depend on the specific applications (database? mail server? machines compiler?), but the above is true for boots, and whenever applications are idle. You should see the profile to know.

  RAID 10 is faster (and often more reliable) than RAID 5 or RAID-6 except in certain specific cases. In General RAID 10 is ideal for many random writes, since the calculation of parity for RAID-5 and - 6 adds to the overall latency between command and response - latency is cumulative if a little slow here and a little slow it adds up to a lot of overall slow synchronous especially with e/s on a network. OTOH RAID-5 and -6 can produce faster readings due to the number of heads, so you can use it for virtual machines that transfer bulk. Test. You may find that you need several different types subdashboards for best results.

  You said 3ware, they have some good grades on their site, but don't believe it. With my 9650 that I found myself with only a couple of their recommendations-, I put the (simple) table for allocation size 256 k, nr_requests at 2 x the queue_depth and use the planner date limit. I had the habit for the Ext4 file system formatted with stride and stripe-width synced to the table and used the options large_files with fewer inodes (do not use the huge_files option unless you plan to have single VMDK files in the terabyte range). Use a cache of great reading in advance.

  Virtual machines use VMDK files in all cases except raw iSCSI LUN that they treat native disks. VMDK is easier to manage - you can make a backup by copying the file, you can move it to a PC and load it into another flavour of VMware, etc. There could be some features iSCSI to your San as a transparent migration but nothing for me. NFS has less chatter of Protocol if latency lower times to complete an operation. NFS is good to read and write a block of data, that's all it boils down to.

  UPS is good, but it won't help if something inside the machine explodes (UPS does nothing if the PC power supply goes down). If the RAID card has an option for a battery backup module, so it can contain some writings in memory and may end up the disk i/o after replacing the power supply. 3ware also limits the types of caching available if help is not installed, and you get just the right numbers with the module.

• Local connection Multiple functions

  Hello

  I have two exe files and trying to control with the other in two different windows (transmitter / receiver Windows)

  I do this in AS2 simply because the original cut (editing one screen now, they want a second screen) was some time in AS2 and I didn't re-create...

  I got the first function to work but can't get the second function to work and I don't know why... new local connection work so obviously I'm missing something.

  I do Code in a picture on its own layer to control all the buttons on a LocalConnection:

  Sender code:

  sending_lc = new LocalConnection();

  mybtn1.onRelease = function() {}
  sending_lc. Send ("my_lc_as2", "execute_this", gotoAndPlay (2));
  }

  mybtn2.onRelease = function() {}
  sending_lc. Send ("my_lc_as2", "execute_this", gotoAndPlay (4));
  }

  The receiver code:

  receiving_lc = new LocalConnection();

  receiving_lc.execute_this = function() {}
  gotoAndPlay (2);

  }

  receiving_lc. Connect ("my_lc_as2");

  receiving_lc.execute_this = function() {}
  gotoAndPlay (4);

  }

  receiving_lc. Connect ("my_lc_as2");

  Basically, I'm trying to get buttons (6 in total) on the sender to transmit the receiver to a new framework on the release. The "mybtn1" button works and send the film to receiver in box 2. The "mybtn2" button, but does nothing and I'm obviously not put together properly. Any ideas? Help? Please?

  Chris

  No object should have code attached to it.

  delete all of these statements on (release).

  mybtn2 test again and see if you can get the track work.  If you can not you do not have an object named mybtn2 that exist when this code stops, or you're not clicking mybtn2.

• Lenovo Solution Center: Local Connection Test: WARNING

  Hi, I'm getting a connection test local warning when the solution center of Lenovo runs a hardware diagnostic test. How to solve this?

  Hi thanks for the reply. I solved the problem. I use a wired connection and had no WI - FI enabled when you run diagnostic test. Turned on then ran test and everything is fine.

• Why the connection to a local database becomes lost when the network is disconnected?

  I use TestStand 3.1. I have a configuration database on the local drive and I use the option "Log on the Fly.

  The test takes 48 hours and I want to assure you that it will not stop if the network connection is lost.

  If I unplug the network before starting the test, fine. I can plug the network again while the test runs without problem.

  But if the network is connected and I start the test and then disconnect the network of recording on the fly will give an error.

  I narrowed down it to "New USE for database Logging" step in the SequentialModel.seq (process model). If this step is performed with the network connection then the rest of the test needs a network connection.

  Is it possible to avoid this error?  The point of all the local database was to avoid network problems.

  Thank you for your help.

  TDOT-

  I connect you always locally, please try to change it to "localhost\SQLEXPRESS" to see if you can log in and then see if the same problem as you disconnect the LAN causes previous saw.