I use a laptop Windows 7 in the office wireless remote for my desktop running Vista. The connection disconnects regularly "try to reconnect 1 20.

Similar Questions

• When you try to connect from my vista desktop to my laptop windows 7 through the DRC I get the error "unable to connect to the gateway terminal server."

  problems of the DRC of vista for windows machine 7

  I have 2 computers running on a homegroup. When you try to connect from my vista desktop to my laptop windows 7 through the DRC, I get the error "unable to connect to the gateway terminal server."   Can I remotely from the laptop to the desktop vista end. I the DRC 7 is installed on the desktop and tried to connect using the IP as well as the name of the machine but still no joy.

  can someone shed light on this please?

  Hello

  Temporarily disable the security software on both computers and check if it makes a difference.

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats.  In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

• When I opened my cell phone message shows that Windows detected a hard disk problem I use toshiba laptop windows 7

  When I opened my cell phone message shows that Windows detected a hard disk problem I use Toshiba laptop windows 7

  Hi Vimalpal,

  To provide the proper resolution, I would need more information on your side.

  1. What is the number of the model of the laptop?

  2. did you of recent changes on the computer before this problem?

  Method 1:
  I suggest to run the troubleshooter and check if that helps.

  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2:

  I suggest you run the disk check and check if it helps.

  Check a drive for errors

  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors

  Important: when running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost.

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• My laptop Windows XP seems to want to treat my broadband as a dial-up connection and, of course, there is no phone line hooked up.

  My laptop Windows XP seems to want to treat my broadband as a dial-up connection and, of course, there is no phone line hooked up. I tried to create a new connection to broadband under network connections and also, the unit seems to work fine. Any suggestions please?

  original title: I can't connect to the internet.

  Hi anthony meechan,.

  Follow these methods.

  Method 1: Temporarily disable the security software.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Step 2: If the problem does not persist in SafeMode with network, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 3: Follow the steps in the article.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  How to reset the Protocol Internet (TCP/IP)

  http://support.Microsoft.com/kb/299357

• try to connect the blue ray player to my laptop, everything works except the connection to the gateway?

  try to connect the blue ray player to my laptop, everything works except the connection

  Hi ArnoldWalterArnold,

  What exact error message that you receive?
  How do you connect your Blu - ray player to your laptop?
  This thread may contain information that can help you:
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/playing-an-external-Blu-ray-drive-on-laptop/cfeeeacc-043d-45B7-9570-dbefb9c9172d

• Windows 8 times the device disconnect sound...

  Windows 8 times the device disconnect sound, my screen goes black, then both the windows the device plug his and my monitor turns on again. All my windows open and then re sizes to the top left of the screen. This happens randomly as I work with the computer. I have a Dell Vostro 270 connected via a VGA cable to a Samsung S22B300. I checked the event logs and Device Manager. Everything seems good. Please help if you know what this may be.

  Typically, this means two things: either the cable is loose, or the video driver broke down.  Usually if it's the driver, you would see that in the event where newspapers and maybe even a notification bubble near the clock when you see your desktop yet (something like "your display driver recovered").

  Do you see something like that?

  In addition, when the problem started to occur?

• No related video and audio when using a sequence of nest in the source Panel and try to insert a clip in the timeline

  When I use a sequence of nest in the source Panel and try to insert a clip in the timeline, the video and audio are not related. Before this update (2015.1), I did not have this problem.

  

  Hi Daniel,.

  I can confirm this matter and will get a logged bug. It is a pain, but after having been published in the sequence, select the audio and video components, right click and select 'Link' to link the components between them. Sorry for the inconvenience.

  Colin

  First Pro EQ

• "The remote computer has disconnected your session because of an error in the licensing protocol. Try to reconnect to the remote computer, or contact your server administrator. »

  Hello

  I received the following error message

  "The remote computer has disconnected your session because of an error in the licensing protocol. Try to reconnect to the remote computer, or contact your server administrator. »

  This happens when I try to log on my remote on the icon access log, I put on my computer at home so that I can get to work if I need to.  He worked for a few months after I bought my new laptop and software, but now suddenly it doesn't.  I talked to my guy TI in the work and they seem to think it's a common problem with "Vista Home Premium", I can do to change it so that I can use the remote access icon?

  Thanks in advance

  Hello
   
  Licensing protocol handles the communication of information on licenses between your computer and the remote computer. If there is an error in the licensing protocol, your computer may not be connected to the remote computer.
   
  To resolve this problem, restart the computer and try connecting to the remote computer. If you continue to receive this error message, contact the server administrator.
   
  This also occurs if one of the registry entries is corrupt. Try the following steps to resolve this problem.
  1. Click Start, type regedit and press to enter.
  2. on the window of the registry editor, navigate to Computer\HKEY_LOCAL_MACHINE\Software\Microsoft\MSLicensing
  3. right click MSLicensing, click on export and provide a file name for example RemoteKeyBackup and click on save to the desktop.
  4. right click on the HardwareID key and store under MSLicensing folder and click on delete.
  5 restart the computer for changes to take effect. Restarting the computer will create new keys.
   
  NOTE: If the problem persists, then you can take backup of the MSLicensing registry key and to load it on the computer of the problem, this will fix the problem.
   
  Visit this link for more information:
  http://TechNet.Microsoft.com/en-us/library/cc756826 (WS.10) .aspx
   
  Important: Incorrectly editing the registry can cause serious problems on the computer.
  Back up the registry: http://windows.microsoft.com/en-us/windows7/Back-up-the-registry
   
  Try the steps and check the result.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Eternal HDD PX1266E - 1 25 retains the connection/disconnection

  I have an external HARD drive, type PX1266E - 1 25, that no longer seems to connect with my laptop.

  Until yesterday, everything worked fine, but then I started to hear the connect/disconnect sounds windows all the time (a first, later others and repeated all the 1-3 minutes approximately).

  They disappear when I remove the cable of the USB ports on my laptop HARD drive.

  If I look at computer Magement - Device Manager - Universal Serial Bus Controllers, I see that whenever I hear the sound connect, Device Manager refreshes and a new item "USB Mass Storage Device" appears between 4 'Intel (r) 82801 DB/DBM USB Universal Host Controllers"and 4 'root USB Hubs' already contained. When I hear the noise of the disconnection, the USB MSD disappears again.

  Following some comments I found on the web, I've uninstalled all the USB controllers and restarted, to clean, but that made no difference.
  If I right-click on the MSD line for the short period that it is visible and select uninstall, then reboot, my computer laptop actuall does not see the external hard drive (the balloons found new hardware USB 2.0 CD + HD and found new hardware USB Mass Storage Device appeared), but the drive is not really recognized (he normally stood like a G (: hard drive).
  Sometimes I get an error message as well after you have uninstalled the drive and when it is reviewed by the PC (a third balloon indicating that a problem occurred during hardware installation. Your new hardware might not work properly), but that only seems to happen if after uninstalling, I don't not yet restarted, but at the same time the HARD drive went through his routine to disconnect/connect again.

  Any suggestions on what I can do?

  Hello

  It of difficult to tell if it s really a laptop or drive HARD USB related issue s
  In your case, I would try to connect the HARD drive to another computer/laptop to check if the same thing would happen with an other other computers.
  This will help you know if his laptop or external HARD drive issue

  But to be honest, it seems that drive TOUGH question... maybe this disconnection messages balloon appears because the HARD drive stops working.

• How to use my laptop HP UK in the USA, I already have a universal adapter to connect

  HP G62 laptop

  Product number: XF230EA #ABU

  Operating system: Windows 7 64-bit

  I'm travelling to the USA, and I want to bring my laptop. I bought the laptop in the United Kingdom, I also have a universal adapter. How do I use it with my UK Plug and can I change adapter or converter.

  You must use a converter of pine with the universal adapter. See the following link for the view of this converter:

  http://www.Amazon.co.UK/US-UK-plug-travel-adaptor/DP/B0006OFKNC

• : Blue screen on my laptop which is runningWindowsXP the connection of the process window termiated unexpectly having the status of this system was arrested (I have windows xp)

  could someone please help me turn my computer again it is the problem:

  Blue screen on my laptop which is runningWindowsXP the window connection process termiated unexpectly with status OxC00000135(0x00000000 0x00000000) this system was stopped (I have windows xp)

  Hello

  Can you zip the minidump in the C:\Windows\Minidump folder files and (provide link) available via Windows Live SkyDrive or similar site?

  The following link has information about the use of Windows Live SkyDrive:

  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  LC

• Networking my laptop Windows XP, and the Windows Vista desktop

  Hello

  Can someone help me with my laptop Windows XP and Windows Vista desktop network?  Despite many attempts (and failures!) I was not able to get the two machines on the same network.  It's very frustrating because I'm unable to access the documents from one computer to another, i.e. file sharing etc and have spent ages trying to do this!

  I would be very gratful if anyone can solve this for me!

  Kind regards

  Here is an article on how do: http://www.informit.com/articles/article.aspx?p=1165037.

  Here is another article on how to do it: http://technet.microsoft.com/en-us/library/bb727037.aspx.

  The next thread can shed some light on the process (and provides a number of useful links):http://forums.techguy.org/networking/545552-how-do-i-network-my.html.

  I hope this helps.  Read all the articles and their references before you start, then use the one you think is the best and follow the process as indicated.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Can I Exchange BONES? I have a laptop running Windows 7 and desktop running Vista Home Prem Home Prem I have the OS disc.

  Hi, can I Exchange OS? I have a Dell laptop under Windows 7 Home Prem and a desktop Dell running Vista Home Prem. I have the OEM operating system disc. What I would do is put Vista on the computer laptop and Windows 7 on the desktop. The office is very capable of running Windows 7 BTW. Thank you

  Hello

  N °

  You can not do

  Dell machines come with preinstalled operating systems

  the operating systems pre-installed are OEM licenses

  OEM licenses are tied to original material, they are installed on this machine life

  When the machine dies dies of windows with her license

• HP envy laptop laptop 15-ah150na: loses the connection to the wireless network device I had not only portable for 2 days

  Loses the connection to the wireless network sometimes directly after that the computer is turned on at other times after 5 min and sometimes after an hour.  No other device I have loses the connection to the wireless network.  Help, please.

  Hello @fairgame,

  Thank you for visiting the Forums from the HP Support! The forums are a great place where you can find solutions for your problems, with the help of the community!

  I understand that you have a problem with the WiFi and wanted to help you!

  First of all, try to review the next steps, offered by community member @Great-Christine-Tree:

  First of all, we have a step by step guide to guide you through the process of diagnosis here:

  HP PC - troubleshooting Internet and wireless network

  A second option is to try the following steps:
  Powercycle the network:
  1. turn off your laptop.
  2. unplug the power to your router.
  3. disconnect the power to your modem.
  4. wait at least 45 seconds.
  5 reconnect the modem and wait for it to come back online.
  6 plug in the router and wait for it to come back online.
  7. turn on your laptop and test your connection.

  Turn off the power to the adapter:
  1. open Device Manager. (Win Key + R > type devmgmt.msc > OK)
  2. expand the network adapters.
  3. right click on the Ethernet adapter / wireless, and then click Properties.
  4. click on the power management tab.
  5 remove the check mark next to allow the computer to turn off this device to save power.
  6. click on OK.
  7 test cycle.

  Reset the TCP/IP settings on your PC:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh int ip reset resetlog.txt" without the quotes and press ENTER.
  4 restart your PC and test.

  It can also help to reset the winsock catalog:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh winsock reset" without the quotes, and then press ENTER.
  4 restart your PC and test.

  Reinstall the NIC drivers:
  1. download the drivers from here , but do not run them again.
  2. go to your Start menu/screen and type Device Manager.
  3. expand network adapters.
  4. right click on the wireless adapter and choose uninstall.
  5 install the drivers downloaded in step 1.
  6. restart your PC and test.

  Test an ethernet connection:
  Explicit. Test if the problem persists on a wired connection to the adapter hardware troubleshooting wireless can be directed to the appropriate areas.

  Test another connection:
  Many people excluded their home network as a problem if another device working on the same network. Networking is not as simple as that. Each device interacts differently with your router or modem and it is impossible to exclude the settings for this device until the laptop has been tested on another network.

  If these steps do not resolve the problem, try this document published by Microsoft for network management issues: wired and wireless network problems. You can change the operating system with the drop-down list in the upper right of the document.

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• Windows Live Mail - the connection to the server has failed.

  I use Windows Live Mail to read my email.  Today it stopped working with the following error:

  Can't send or receive messages for the Yahoo! Mail account. The connection to the server has failed.

  Server: 'pop.sbcglobal.yahoo.com '.
  Windows Live Mail error ID: 0x800CCC0E
  Protocol: POP3
  Port: 110
  Secure (SSL): No.
  Socket error: 10061

  It has worked very well.  Nothing has been changed or reconfigured by me even if I noticed that an update of Windows ran last night.

  Any suggestions to fix this?  I'll be happy to publish any necessary additional info.  Any help would be appreciated.

  Try these new account settings.
   
  Required changes continues using AT & T / SBC e-mail out
  http://www.technology-USA.NET/downloads/SBC%20Global%20pp%20Setup.PDF