I want to set a specific timeframe for Upddates automatic

Similar Questions

• Cannot set a specific repository for a machine

  I tried many ways to change/set a specific repository for a specific computer and it always goes back to the original.  I removed from the basic machine (saved restore points) and created a new repository. When I added the rear machine automatically resumed inside the restore points, etc. and back have been started.

  I removed again (guarded restore points), pushed the agent to the machine and selected the new repository and he said the agent on this computer is the same as the agent on this computer and reset it with the changes. Rebooted the machine.  However, he still picked up points of restoration on the core and attached to the old repository.

  I tried a total of 5 different ways to get this machine to see a new repository, but no luck.  The only thing I did is remove the machine & points of restoration out of the nucleus and the Constable and I tried.   Archiving is a joke to say the least and takes 20 hours to around 2.2 to has failed or * the rest of the system (as he did last night).

  I used several different backup systems, but AppAssure is by far the worst, slower and less reliable I've seen.  Even my old band system Veritas has been 100% reliable and I spent less time to manage.

  I'm only protect three machines on it so it can't be that difficult.  Any thoughts?

  Thank you. Russ

  Hi Russ,

  AppAssure has a relationship one between the agent and the repository.  You can have data from an agent in a repository at the same time.  Because Wes pointed out you can follow this KB support.software.dell.com/.../117750 . to migrate from the agent and he gave repo from one to the other.

  There is another option to move an agent to a new repository.  You can change the Unique ID of the Agent and then restore it.  By doing this, the kernel will see it as a new agent and allow you to define any repository on your heart, as is the master repository.  If you take this approach, you can keep the old restore points for the agent in the first repository and have all new backups to go to the new repository. Please note that you can never match these two sets of recovery points together once again, because the kernel identifies as a different agent data.  Then they will be displayed always separately.

  To make this change:

  1. Change the display name of the current agent to something different (usually I just add - old for it)
  2. Stop the agent service
  3. On the agent, remove the HKEY_LOCAL_MACHINE\SOFTWARE\AppRecovery\Agent\AgentId registry key
  4. Start the agent service and the registry key and the subkeys will be regenerated
  5. Run the wizard of protection on the basis of protecting agent and be sure to select the right repository
  6. Delete the former agent of protection and keep the recovery points
  7. You have now - former agents like recovery Points only and agent under protection.  A new base image is taken as there is still no data for this agent, but once the base is taken all subsequent backups should be incremental.

  As for your statement about archiving is a joke, I would need to learn more about your configuration to make a statement. What storage do you use for your storage space?  What speed, the size and the number of disks are used?  What RAID configuration? Is it directly attached, NAS or CIFS? Personally, I always found AppAssure as reliable when repository storage is reliable.  Regarding speed, AppAssure runs how fast on your database server resources are capable. I saw TB of data archived in just a few hours.  I've also seen take days.  It depends on the material used.

  Tim

• I want to set up a PC to connect automatically to the field on switch. Netplwiz is not installed

  original title: install netplwiz

  I want to set up a PC to connect automatically to the field on switch. Netplwiz is not installed

  Hi BobSpence,

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows forum.

  http://social.technet.Microsoft.com/forums/en-us/categories/

• You want to set the parental authorization for Xbox live.

  Original title: authorization wizzard - x box live

  I'm trying to set the parental authorization for x box live, but the permission Wizard is American and does not accept my UK address. What can I do?

  Hi LizG1,

  I recommend you contact Xbox Live support for assistance:

  http://support.Xbox.com/en-us/Xbox-Live/browse

  Hope the helps of information.

• Could the developers of Firefox please re - implement the functionality that allows you to set a specific webpage for recently open tabs (as prevented from 2015-Oct-03)?

  October 4, 2015.
  This question is more for developers and users.
  With the introduction of new controls tab an hour or two there is the subject: Config, definition of browser.newtab.url is no longer works. I found this feature very useful, and many don't like new tabs display of my pages preferred in form of icons (or other), or just to be a Virgin.
  If this question does not reach developers (people who I'm and all Firefox users are in debt, although not financially), could they consider adding a parameter new tab control that provides the ability to define a selected page that may not necessarily be the homepage?
  Thank you.

  Hi, 41 of Firefox, you must use the add-on tab override (browser.newtab.url replacement), to make changes to the page tab.

  Once installed, open the Add-ons (Ctrl + Shift + A) Manager > Extensions, and then look for the new tab override and click Options to set your preference.

  Notice, if you want only the new tab to be the same as your home page, you can use the Add on new tab homepage instead.

  You will then need to restart Firefox for all changes to take effect.

  If you want to go back to the Mozilla developers, you can do here.

  If your question is resolved by this or another answer, please take a minute to let us know. Thank you.

• I want to set the default action for a file type.

  When I installed a photo editor the default action has changed from ""Preview " to 'Open'."  I want to return to "Preview".  Someone at - he had success with this?

  You can try your idea as an experimental, if you don't do that you export .jpg any key for simple restoration (import) in the registry.  Or create a restore point from the system to use.  Don't forget that my machine isn't your machine, so he could have probably NOT the goal in all cases.

  Have a look at the default programs in Control Panel.  Control Panel\All Control Panel Items\Default Programs\Set default programs.

  See which by default is actually set to "Windows Photo Viewer.  Click on the words "Windows Photo Viewer", then "choose default program".   Whatever file types you set as the default value for "Windows Photo Viewer" should give you the option to preview "BOLD" as the first and default option on right click for this particular file type.

  Then, you should probably use the Edit option to open a file for editing if you wanted to not just previsualisez?

• How to set the specific proposal for a specific IKE L2L tunnel?

  ASA 5520 running 8.0.4

  ASDM v.6.1

  Need help understanding how in ASDM/Configuration/Site to Site VPN/profiles of connection / "Any Entry" I can clarify that I want only to offer a pre-share-aes-256-sha IKE proposal?

  The area of the IKE proposal has a number of options, including: pre-share-aes-256-md5, pre-share-3des-md5, pre-share-aes-256-sha, pre-share-aes-192-sha, pre-share-3des-md5, pre-share-aes-sha and pre-share-3des-sha.

  I am able to choose a specific proposal of IPSec without problem, but when I try to do the same for the IKE proposal and click OK the choice doesn't "stick", but refers rather to the entire list such as defined above.

  Thank you.

  Hello

  IKE policies are defined globally on the SAA, there is no way to apply policy 1 to a connection and b of the policy to another.

  You can remove all polciies except pre-share-aes-256-sha.

  This could cause a problem that other VPN connections may have a policy to remove in order to connect.

  I hope this helps.

  Thank you

  Loren

• Set the font size for the target PCs ONLY

  I know that I have to include a custom ini file to specify the name of the font AND size for target PCs (those where the EXE is executed).

  For example

  appFont = "Tahoma" 13

  dialogFont = "Tahoma" 13

  systemFont = "Tahoma" 13

  Is there a way to specify only the size of the police and not the name? (i.e. I want to use the specific font for a given PC, but I would like to put its size).

  I tried with

  appFont = 13

  but this setting is ignored.

  When I used

  appFont = '0' 13

  the size was successfully set, but what is the '0 '?

  Hey Vix,

  Yes, I think it will work.

  You could confirm the fact,

  The default Application police is the police of the Box of Message which is respectively Segoi UI and Tahoma for XP machines with Windows VISTA. To check this on a Windows XP-based computer, follow these steps:

  1. "" "Open Start" settings "Control Panel" display
  2. Click on the appearance tab, Advanced
  3. Select the Area of Message of the point: drop-down menu
  4. The police will appear in the are: drop-down menu

  .. the police exchange between '0' and Tahoma for example...

• How to set a default view for 'Open' and ' Save as '.

  I am running Windows XP, Service Pack 3.  I want to set a default view for the windows 'OPEN' and 'SAVE AS' sort by 'Name' of A--> Z.  How can I do?

  Hello

  I suggest you to follow these steps and check if that helps:

  a. right-click in the folder.

  b. click the name to sort by alphabetical order.

  You can also click on the name of the list view to sort the files alphabetically.

• How can I set different background color for the slider?

  Hello
  I want to set a different color for track Slider, slider track is spitted into two sections by slider-button.
  I want to put a left gray, the right of a white.
  Under css only changes the background of the entire track, but how I can change different background color for the slider?
  Any suggestion?
  

  .slider {
      -fx-border-width: 0;
  }
  .slider *.track {
      -fx-background-color:white;
      -fx-background-insets:  0, 1;
      -fx-border-color: #faf0e6;
      -fx-border-width: 1;
      -fx-border-style:solid;
      -fx-progress-color:yellow;
      -fx-border-radius: 20;
  }
  .slider.knobStyle:focused .knob {
      -fx-effect: dropshadow( three-pass-box , red , 5 , 0.5 , 0 , 0 );
  }
  .slider.knobStyle:unfocused .knob {
      -fx-effect: dropshadow( three-pass-box , red , 5 , 0.5 , 0 , 0 );
  }
  .slider .thumb {
       -fx-background-color:rgb(224,225,226);
       -fx-background-repeat:stretch;
       -fx-background-size:stretch;
       -fx-background-position:center top;
       -fx-background-image:url("../images/volume_ball.png");
          -fx-padding: 10;
  }

  I don't know why I can't get the node of the track, track has always set to null and the thumb or the other.

  After that the cursor was displayed on an active scene are you doing research?

  (ex.: after you have added the slider to a scene, the scene for scene, then called stage.show ())

• How to set the threshold value for single tablespace in the 11g grid control

  Hello
  
  I want to set the threshold value for a single tablespace in the 11g grid control,
  Please give me a navigation path.

  Sandy wrote:
  Can you please give me the full navigation path?

  go to the target--> databases
  Select the database that you want to set this alert to
  Link select settings and policy settings

• Me and my dad is from the same Apple ID and I want to set up his own, but how it will get all his contacts, photos etc from my Apple ID? Or he will lose all? or I could keep them saved for him and send more via an application any?

  Me and my dad is from the same Apple ID and I want to set up his own, but how it will get all his contacts, photos etc from my Apple ID? Or he will lose all? or I could keep them saved for him and send more via an application any? I don't know how to resolve this issue, if someone could point me in the right direction.

  Have him create a id Apple here- create and start using a Apple - Apple Support ID, and then both you can create an album-photo sharing Photo Sharing - Apple Support iCloud

• I want to have the spell checker for set email sending to automatically check spelling when I send the mail.

  check spelling

  I want to have the spell checker for set email sending to automatically check spelling when I send the mail. I did, but my spell checker is set by default to a French dictionary. How is it still happen? and how can I get it back to English? It's not an option in the menu drop-down button. There is only the French. HELP!
  You no longer have the correction spell checking capabilities in some languages in Outlook Express 6.0 after you install the Microsoft Office 2007 or Office 2010 system
  http://support.Microsoft.com/kb/932974
   
  Outlook Express cannot use the check spelling of MS Word in Office 2007 or newer. A free spell-checking the download is the easiest way to get around this.
   
  Vampirefo spell check.
   
  Download from Major Geeks:
  http://www.MajorGeeks.com/download.php?Det=2952
   
  Or upload it to SnapFile:
  http://www.SnapFiles.com/get/spelloe.html
   
  You wanted TinySpell or. (Check spelling while typing).
   
  Download it here:
  http://www.tinyspell.M6.NET/ 
   
  Australian English spell checking
  (Also suitable for other English speaking countries).
  http://www.justlocal.com.au/clients/oespellcheck/ 
   
  If you have an earlier version of Office, see this:
  http://www.Outlook-tips.NET/archives/2006/20061228.htm

• Lost my power cord for HP Laserjet P1102W usb and I want to set up wireless.

  Lost my power cord for HP Laserjet P1102W usb and I want to set up wireless. (Instructions say I need cable to do).  How can I set up wireless without buying a new usb cable

  loudford73 wrote:

  Lost my power cord for HP Laserjet P1102W usb and I want to set up wireless. (Instructions say I need cable to do).  How can I set up wireless without buying a new usb cable

  Hello

  If the instructions that you need a cable then you need a cable. On several printers now, you don't need USB cable for Setup (that's why many boxes do not have) and you can run the installation on your computer or a button on the printer.

  Kind regards.

• want to set up Analytics for my Officejet, but have lost the CD with the printing software

  I have the OfficeJet 6500 E709n all-in-one, and I want to set up the function of scan on my Macbook Pro.  The printer function works very well from the laptop.  I have lost the CD with the software on it.  What are my options?  Thank you.

  Hi Dannyp43,

  You can download the software and drivers for your HP.com E709n.

  Please followthis link to access the download page. Click on the '+' next to the driver, then click on the link for your version of Mac OS X. you have the following options to choose:

  -How to install your product in 10.7.x (Lion) - this is a document that shows you how to install 10.7

  -Full Feature software and driver for® 10.6 (Snow Leopard) - after clicking this link, there will be a download button.

  -Full Feature software and driver (Universal) for 10.4 and 10.5 - after you have clicked on this link, there will be a download button.

  Once you have downloaded the software, double-click on the .dmg (download it), and then in the window that opens, double-click the HP Installer.

  If you install USB, connect the cable before beginning installation.

  If wireless, connect the printer to the network (using the front panel) before installing - this is not necessary, it just makes go more smoothly. You can also configure the wireless installation using wireless USB installation.

  Hope this helps