ICP accelerometer

Similar Questions

• Voltage Excitation for IEPE/ICP and IOTech 650U

  Hi all

  I am using IOTech DAQ 650U (OR product no. 781277-01) with ICP/IEPE accelerometer. It works very well with accelerometers of general purpose PCB/IMI (IMI 607 A 11 model example). We want to use seismic accelerometers and wonder if IOtech 650U can collect data from seismic sensors (example - IMI 626 A 04 model). Most of the electrical specifications of the two sensors are similar (2-20 my constant current), except that the voltage is more versatile (18-28 VDC) for seismic sensor (24-28 VDC). -What it means and means of IOTech 650U does not work with seismic sensor? I don't think, but I'm not sure. I tried to read about this subject and found NO article on voltage is lower than the voltage of compliance (http://digital.ni.com/public.nsf/allkb/3CEFD95B14604C7386257598006C6233).
  However, I couldn't find the conformity of IOTech 650U voltage specifications. Any help in this regard is highly appreciated. I want to know if we can use the accelerometer seismic (IMI 626 A 04) with IOTech 650U or not? Thank you.

  Usually you want to measure low or very low frequencies with seismic sensors.

  So check to see if the high passes of frequency of your data acquisition fits your needs.

  A lot more low power low voltage will only limit max amplitude can be measured...

• cDAQ 9184 with module NI9232 for sensor accelerometer and pressure

  I'm currently building a CompactDAQ system for measuring two signals: vibration and pressure in the duct system. The system will consist of the following elements: chassis, NI 9232 Module cDAQ9184. Accelerometer IEPE to measure acceleration (vibration) and pressure for the measurement of the pressure sensor. My question is: can I connect the pressure sensor in the NI 9232 module? I have found on the site OR that this module is designed for acceleration and offers a conditioning of signals and excitation for accelerometers but nothing mentioned about pressure sensors. On the other hand the site mentions NI9237 module as the best choice for pressure sensors. So can I just use 9232 OR both sensors or not.  Thank you

  Here's an IEPE (source of ICP (r)) of transducors pressure: http://www.pcb.com/products/browse_productlist.asp

  Kistler is another provider.

  To help choose - can you tell us more about what you are going to connect the sensors - what is the unit under test?

  What do you do in the hope of discovering or surveillance of the unit?

• Portege M405: Programming for Toshiba accelerometer API software

  I am interested in the programming of an application that would be able to use my computer's built-in accelerometer

  Computer: Toshiba Portege M405 Tablet (w / HDD protection against shock)
  Language: C# or Visual Basic

  I'd be grateful if someone would be able to help me.

  Thank you

  Hey Buddy

  I think that this is not a bad idea, but I doubt that anyone here in the forum would be able to help you...
  Here in the forum, you will find ordinary laptops users who try to solve "common problems that might appear on laptops Toshiba."

  But I doubt that there are people who would be able to help you in this case...
  However, maybe someone knows how to program such request...

• Re: Incorrect accelerometer readings

  I have a strange problem: shortly after the start of my tablet, the accelerometer is weird. Therefore, the acceleration of the screen is always upside down, and it does not meet the rotation of the tablet.

  If I read the readings of accelerometer with a test program, the trend is good, but the zero level is incorrect. 0 g, X denotes + 4 m/s, Y indicates-9 m/s and Z watch-5 m/s. What explains the problem with the rotation of the screen. The only solution seems to be a reset.

  Is that what I can do to solve this problem, or do I need to bring it back? I'm just inside 6 months since I bought it, so I need to know soon...

  PS: This is a Pro to excite 10.1 16 GB, I think AT10LE-A108 is the official type.

  > I feel it was a rogue background process.
  > It is difficult to say which, but I learned that any application can recalibrate (or spoil) the accelerometer.

  Sometimes its very useful restore Android system, but also the tablet to the factory settings. Where the Android system was confused upward through an app or a process, this reset should solve the problem.
  That's why I think you should check it out in case you no it did not in the past.

• Satellite A-P70-11V - HARD disk protection works without accelerometer?

  Hi all

  I'm new here.
  I did another post. In short, I'm expert enough in Toshiba Satellite laptops, but my new, Satellite P70-A-11V, a portable high professional range, had some problems. It came with Windows 8, which I upgraded to 8.1. Unfortunately, the degraded system so bad that all pendrives made plant. I have connected my Toshiba camcorder, and it also crashed the laptop.

  The search indexing was not working outside the C: drive. The pointer of an optical mouse has started to freeze for seconds on the screen.
  This last I believe was due to the low power USB ports.

  So, I really had no choice after 2 restorations system total and installed Windows 7 Enterprise x 64 SP1. Operating system almost seems ok, but I still have problems, and one of them is that but I'm trying to install the accelerometer utilities, there is no driver.

  I tried that Windows 8 x 64, but just, it does not appear on the list of services.

  I found that the utility of the HARD disk protection was also arrested, I searched this forum and someone said that the Intel Rapid Storage technology must be uninstalled. I did and my HDD is running... but I don't know if it's effective!

  I remember with the 8.1 Windows, the utility always shown a message on the upper right: Vibration is detected, the drive is temporarily closed, etc..

  She has been associated with some high tone sound indicating that the drive has been effectively stopped. Now I can shake it off the laptop, but no message appears, there is no sound.

  I checked all the boxes on the interface of protection of HARD drive to indicate if there are vibrations, but so far nothing. The drive protection is in place and running, but in the absence of use of the accelerometer, the protection of disk HARD just don't know when to act.

  Am I wrong? Can Toshiba fix this?

  All responses are greatly appreciated.

  Hello

  Toshiba drivers and tools available to win 8 or 8.1 to win are not entirely comparable with Toshiba available for Win 7 OS software.
  Some drivers and tools that are available to win 8 don t exist for the Win 7 system.

  For example; commercial accelerometer or HDD Protection Utility released in particular to win 8 / Win system 8.1 and are not available for Win 7.

  But for Win 7, you can find the Toshiba VAP (value added package) and this package installs a range of important services that are an essential component of the Windows system and this PPV will perform the other original programming TOSHIBA works correctly.

  Therefore, you must install the VAP as Toshiba's first tool to ensure that other software such as HDD/SSD Alert Utility or PC Health Monitor

• Windows 7 Pro x 64 does not detect HP Mobile Data Protection Sensor (accelerometer)

  Hello.

  I installed win7pro x 64 yesterday and already fallen on a serious problem, which is how I use the laptop a little dangerous for my valuable data.

  When I was working on HP Vista 32 bit (of the partition recovery etc.) brand, it was a device called the HP Mobile Data Protection with HP ProtectSmart software sensor (or protect Smart). In other words, the accelerometer HDD which parks the HARD drive heads when it "feels" it is down or something and the software for it. It has worked flawlessly.

  
  

  Until I decided to install Win7... And then, surprisingly, after failure of driver install and take a look in the Device Manager, I have noticed that there is no such device. I checked three times, looked at property of each device, even reinstalled Vista 32bits back - he has shown again - and installed Win7 - not detected again. There is nothing that has the HPQ004 device ID! I remember people saying that after that fresh Windows installed, there are 6 unknown devices or more. I got only 5. [Device fingerprinting, 3 x MemCard player and IR receiver]. There is no accelerometer... Also, when I try to install the drivers/software, windows appears:

  ProtectSmart Hard Drive Protection: with the text Property.AccelerometerNotPresent

  and then another saying something like features were not installed due to wrong installation or not supported feature.

  So now I'm stuck with a laptop it is dangerous to travel with, because the disk is no longer protected

  I have already installed all the drivers available on the HP page, even downloaded those newer Intel (chipset) etc.

  Is there a solution to this? Has anyone else encountered this problem?

  Windows 7 is officially released and available in RTM version, not beta, so I think that HP should open support in his favor and release new drivers for win7! And above all, to solve this problem...

  If anyone is interested, this problem is solved now.

  Just download the new drivers from http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en & cc = us & prodTypeId = 321957 & prodSeriesId = 3744188 & swItem = ob-76187-1 & mode = 4 & idx = 2, install and make sure you have the latest version of the BIOS. Tested - heads are being finally parked! Yay!

• Portege M700 - Rotation buton and the accelerometer does not

  Running Vista Business 32-bit.

  When I put my M700 in tablet mode and tilt the tablet to 1side and press the button next to the slider he used to rotate the screen in that direction.
  He doesn't do this more. I have
  Note also that all the utilities of the accelerometer, like tilt, shake and advanced security no longer work. detection of movement of hard drive does not work.

  I reinstalled from recovery discs and installed original and new extension of the tablet version and pvat. Nothing seems to help. I also installed Windows 7 ultimate 64-bit, it does not work there either. I've actually noticed that it also does not work on vista because of this does not not under Windows 7.

  I wonder whether or not my accelerometer is broken or not because it allows to work with the original installation of discs or is it a software problem?

  Hey mate,

  > I reinstalled from recovery disks
  To be honest, if you have the same problem with the factory settings, it appears to be a malfunction of the equipment. With the settings everything should work properly without updating a software or driver.
  So I recommend you contact an authorized service provider. Guys can help you because here it s only a user to user forum.

  By the way: is the new version of the BIOS installed?

• Yet WT8 - question of Gyroscope (accelerometer 3 axes) all in game

  Hi all

  Recently I bought unit Toshiba again.

  However, I am not able to solve the problem with the accelerometer (or gyroscope).
  I will use the example of asphalt 8 game despite the fact that I checked several other titles.

  Still has the same problem.
  While gaming, it is only the left... only it self.
  If I'm blocking the past of automatic position of the screen that allows the car to turn right.

  Could you please tell any resolution?

  Thank you very much

  This problem occurs with all tested games?

  Check if its possible to calibrate the accelerometer in the game settings.

  How about you, affecting the system back to factory settings?
  Have you tested it?

• Calculate speed using acceleration < accelerometer iPhone >

  I'm working on an application where I need to find the speed and Distance without using GPS. I did some R & D on the accelerometer and the Framework.but movement could not be any idea my job. Any suggestions are welcome.

  Ask Mr. Newton. You must integrate the accelerometer of entry (in the mathematical sense of the term) to get the speed and integrate to get the distance.

• Are there problems with the accelerometer/compass on the Flipout?

  My flip is great, except that most of the applications that use the accelerometer does not work correctly.

  This includes: drop http://www.android.com/market/#app=com.infraredpixel.drop

  Labyrinth lite http://www.android.com/market/#app=se.illusionlabs.labyrinth.lite, aTilt 3D labyrinth free http://www.android.com/market/#app=com.fridgecat.android.atiltlite, and the reality applications, Wikitude and Layar immersed.

  In all this, left, right, front, rear are twisted.

  On the other hand, the "abduction" game seems to work fine, and it uses tilt left/right to lead your cow...

  I wonder if this a bug in all of these programs, a bug in the Flipout, or just a problem in my phone.

  Else you have noticed this problem on their phone?

  Yes, I have a flipout. I tried Labyrinth lite and it works fine.

  You can try to go in the game settings and calibrate the level. You can also try to do a software reset the phone, but you may have a hardware problem.

  If a reset does not work, then you will need to exchange the phone. MotoBlur will restore much of your data, but you will lose messages SMS and photos - but let's go back to the top of your data on your computer or SD card.

• HP EliteBook 840 G3: Impossible to find acquisition of ICP data and Signal Processing controller, memory controller, PCI and SM...

  Hello

  I can't find acquisition of ICP data and Signal Processing controller, memory controller PCI bus controller SM for HP EliteBook 840 G3 running Microsoft Windows 7 Enterprise (64-bit).

  Any help is greatly appreciated!

  Hello:

  See if this driver works...

  FTP://ftp.HP.com/pub/SoftPaq/sp74001-74500/sp74152.exe

• Satellite P850 - wonder about the accelerometer pilot description

  I was delighted to see an accelerometer for the P850 pilot in the driver downloads.

  I was also happy or sad to find that it was really a hard throttle.
  There must be a correction of the description, or the correct driver should be loaded.

  I assume you mean the [utilities accelerometer | http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 2 & selSeries = 152 & selProduct = 7507 selSh ortMod = null & language = 13 & selOS = all & selType 216 = & year = upload & monthupload = & dayupload = & useDate = null & mode = allMachines & search = & action = search & macId = & country = a he's & selectedLanguage = 13 & type = 216 & page = 1 & ID = 88083 & OS ID = 46 & driverLanguage = 42]

  Description says:
  + These utilities are a set of utilities of material working with motion detectors built into your machine. With the accelerometer, your machine will be able to detect the position you hold your computer at any given time. You can set the machine to perform a specific function when the device is tilted quickly left or right, either at the front or back. You can also take control of the cursor in some applications and move by leaning the PC in a certain direction. +

• HP PAVILION NOTEBOOK 17-g000nv: accelerometer for windows 10 pilots

  I have the HP PAVILION NOTEBOOK g000nv 17. I do not see my accelerometer in nowhere Device Manager, and looks to does not work. Please guide me to solve the problem or perhaps install new drivers for windows 10.

  Thank you

  Hello:

  You can find out if 3D driveguard is installed by going to Device Manager, click to expand the category of peripheral system and then look for the HP Mobile Data Protection sensor.

  If you see the device listed, then you should be fine.

  If you want to update the driver, here is the latest...

  This package provides the software HP 3D DriveGuard to the notebook models that are running a supported operating system. HP 3D DriveGuard software protects the drive hard by parking the heads if cell phone accidentally falls, or is suddenly struck by another object.

  FTP://ftp.HP.com/pub/SoftPaq/sp75501-76000/sp75979.exe

• Noise measurement of an accelerometer with card PCI-4461

  Hello world

  I'm trying to measure the noise of an accelerometer, except with a card PCI-4461.

  First of all, I measured manually this noise with the help of a HP35665 signal Analyzer. I get something like this:

  

  And now with LabView and the PCI-4461 map, I get this:

  

  My question is: Whence this part? And how to remove it? (Since there is no with the signal Analyzer)

  

  I'm using LabView 8.5.

  This is how I configured the DAQ acquisition:

  

  and it's my VI:

  

  Thank you in advance for help

  Arthur