IDRAC reset

Similar Questions

• Reset the Web GUI on the M600 iDRAC

  Hello

  I have problems of access to the iDRAC web gui on a couple of blades M600 (needed to get the console and re - install the operating system).

  I read on Google that racadm racreset running can solve the problem, but this seems to be only available on of m610?

  When I ssh into the M600 blade I gives me a prompt SMASH CLP Console (v1.08) and can not find everything related to actually reset the interface itself idrac.

  Is it still possible on a M600?  Otherwise, how can we reset the iDRAC interface?  It does not fundamentally on port 80 - unlike our other blades, also M600s.

  Thank you very much in advance for any pointers or direction.

  Thank you

  SoC

  Rob,

  An option to rest iDRAC on M600 is with the CMC. You can connect to the CMC and perform iDRAC reset page "Overview-> troubleshooting-> Reset chassis components. Select iDRAC reset for the corresponding housing option. You can also do CMC Racadm. Run "racadm racreset m - Server -" of SSH or using remote racadm and CMC IP.

  What iDRAC firmware you have on M600? 1.65 is the last FW for iDRAC M600. If you do not have this FW on iDRAC can you update and check the same. You can download the same from

  www.Dell.com/.../PowerEdge-M600

• How can I fix my "iDRAC is not ready' problems?

  We have a PowerEdge R420 running a server VMware ESXi 5.1 in RAID mode.
   
  We had a power failure which resulted in obtaining R420 one ' SWC0700: iDRAC is not ready "error.  Our version of setting iDRAC is 1.30.30.27.  I found the report on the iDRAC reset and update the firmware of the iDRAC with this version and error state.  Following suggestions to disconnect power cables, USB cables and then keeping the power button for 15 seconds until not clearly the problem.  Boots following this process had the same error of SWC0700.

  I created an OSMA7.1 DVD boot and I tried to install, a USB drive, different versions of newer than 1.30 iDRAC, but every time that the system has reported/proc/ipmi/0 /: file not found (or something similar that I'm going on memory here).

  I needed the system upward, so I pressed F1 to continue to run.  The system seems well except that the fans turn at high speed.

  I saw another post on the button of the iDRAC for 15 seconds to reset the iDRAC, and I tried with the system in place and is functioning normally.  This did nothing for the speed of the fan, so I guess it has no effect on iDRAC.

  I installed the COnsole of Administration Dell, on the ESXi virtual machine in the hope of launching an upgrade of firmware iDRAC of this virtual machine, but I couldn't connect to vCenter, which is probably because I don't have a VCenter server, only two servers ESXi 5.1 - I think I misread the DELL site thought this could work somehow for me.

  Now, I think the performance of the ISO bootable, I found on this Web page: www.dell.com/.../SLN296511
  My fear is that something can go wrong, and I'm losing my server installation.

  If I put my confidence in the ISO bootable update?  Should I call Dell support - I am about 4 months out of warranty repair technician on-site - and plan to replace my motherboard as I read in other posts on this forum?  The motherboard can be replaced without altering my ESXi installation?

  I'm worried that runs the server with a "iDRAC is not ready" error will burn the server, or do anything else that will ruin the server.  Should I still worry about this?

  Thanks for the advice and suggestions in advance.

  The f

  It sounds like the replacement of parts is necessary. There is not a way to export the configuration of the BIOS. The fee for a replacement of tech is usually $299 for servers, plus the cost of the system board. I'm not sure what would be an extension of one year on the guarantee.

• Factory defects R710s

  Hi, I got the task to reset a number of R710s,.

  which is the best way to erasing\resetting all the user settings\data on them, I removed the readers and disinfected them with a data wiping program, but what about servers?

  I went into the bios and used the stop scroll, NumLock, CapsLock and keys ALT combos that are supposed to reset the NVRAM and restore the default settings.

  But what about resetting the LC and iDrac to the factory settings, which will remove all credentials iDRAC user and IP addresses also configuration settings it would remove all lifecycle logs that contain the history of all change events, firmware update and comments from users.

  would you advise to reset of the LC and iDRac and if I do it won't have problem when servers are used by someone else?

  Thanks for the tips...

  Jon.

  john_jones7

  What advise you to remove any info from company, as asset info, domain etc.

  clear memory nvram and reset the iDRAC in the default bios menu or?

  Clearing NVRAM via jumper will reset the BIOS TO default system and remove information from there. It has no effect on iDRAC. IDRAC resetting to default values should remove all information from the iDRAC come to be listed. If you're going to be when you run the LCwipe then that should be all you need to do to clear the information from the iDRAC. Which should remove all newspapers and all the information that would clear a reset to the default values.

  Thank you

• M600 No. Web Interface after update to 1.11 to 1.65 iDRAC

  Hello!

  We have a few M600s which have not been updated for a while and are still ongoing iDRAC 1.11. When we update to 1.65 that they do not always have a Web Interface like some of our other M600s which have been maintained over the years. Looking at the scans Nmap and Wireshark, it seems that port 443 is blocked even if it is defined by default in cfgRacTuning. We tried to reset the newspapers, configuration and adjustment of different ports but not luck.

  We run CentOS 6.6 on these blades, and our upgrade method uses the file .bin on the Dell site. I was wondering if there may be another method of upgrading for those with them running old firmware.

  Thank you

  Stevie

  Found the solution.

  Looks like there's an old bug where when downloading a cert Active Directory it would replace the Dell SSL cert and we had a few old m600s that never have been set. To return to the original self-signed cert Dell iDRAC firmware must be 1.11 and run "racadm racresetcfg." All the foregoing 1.11 does not seem to reset the cert.

  The other solution is to download a signed CA certificate.

• Cannot connect in the company of the iDrac 6

  iDRAC Enterprise never works on the login page that is a known issue on the net. I can not connect via Firefox, IE11, Edge, nothing. It refreshes the page in IE11 or connection, connect and everything says "undefined". Yet, it works in mobile Safari. Worst platform ever.
  Try to update the firmware via mobile or impossible (appears just "progress" for more than 15 minutes, not normal). I already used the idrac repeatedly reset tool. I even created a new ADMIN activated via the mobile browser, tried again through the office. Nothing.
  Why is their platform so useless and impossible to use? Seriously, Dell, get a grip. Your download section is such a mess and too confused.
  I guess this is the download page correctly
  www.dell.com/.../DriversDetails
  and the file, even if I can not connect my company to the idrac gui
  ESM_Firmware_78M0V_WN32_1.98_A00. EXE
  
  I'm so tired at this point and need help.
  My local machine is 10 64-bit Windows. I have installed java, latest version, and I added all my https://serverIP/login.html to the list of white security in java. Restarted. Tried several browsers.
   
  My server is running Linux 64-bit Centos 6.7.

  Try to run the sync .bin file , directly on the server and not on your client system.

• iDRAC Active Directory integration

  Hello

  I recently tried to integrate all our DRACs here with Active Directory to connect this way, rather than a generic username and the password shared by several employees. I downloaded the Dell Remote Access Configuration tool and it works beautifully. It is able to define the appropriate settings for many DRAC allow AD users to sign everything at once.

  However, there is a slight problem that I can't seem to understand. On the DRACs 11 of the ~ 50 that I have configured this way, credentials fail. I thought maybe I was just fat-fingering the keys, but after having several people try both the holiday and work DRAC, there seems to be a problem with the way those 11 have been configured.

  I did every configuration run in groups of about 10, and within each group, there was 1 or 2 that just did not work properly. After you have compiled a list of the 11 who did not work properly, I even tried to run through Setup once again, does not. And looking at the information provided to me, there is nothing to differentiate these from another ~ 40 who succeeded. There is so much iDRAC6s and iDRAC7s, and there are several different firmware versions. Basically, what I'm trying to say is that if I have a card DRAC of the same type in the 11 that don't work, there are one of the same type, version of the firmware, model and in the 40 ~ that work. So, I can't see the problem.

  I hope this is enough information to find someone has begun to help solve my problem. If anyone has any questions or suggestions, I would be very happy to have in your.

  Thank you

  Jacob

  Hello Jacob

  If there was a problem with one or two iDRAC, I would say that this could be a hardware problem or a problem with a bad firmware image. Because what is happening across a large percentage of your question iDRAC is probably with the configuration of your network or security. I suggest you to check your network configuration to ensure that the iDRAC who have problems is able to communicate properly with the advertising server.

  If you feel that there is a problem with the iDRAC so I suggest firmware reflashing, reset the default values and then reconfigure one of the iDRAC problem manually to see if the problem persists.

  Thank you

• Cannot change network iDRAC settings 7

  Hello

  I am trying to set up alerts e-mail for a few servers and have encountered a problem with the network settings on the iDRAC. The problem is that the DNS settings is not configured correctly on most of the servers, which would require me to use the direct IP to my SMTP server, that I prefer not to even if it would work. I have also some machine with an incorrect host name value that before email alerts has been only a slight cosmetic problem in the interface.

  When I try to change the settings on the network tab in the iDRAC charging page interface with old settings just once I hit apply. There is a note on the top of the page that tells me that the NETWORK card must be reset to apply the settings, but settings will still apply after reset of the iDRAC together.

  Hi AlbinG,

  Can you give us more details

  1: what server do you use?

  2: iDRAC FW Version

  3: what setting all you changed on the iDRAC network page.

  4: do you have any VLAN configured on iDRAC?

  5: what operating system and browser you use to launch the iDRAC Web Interface?

  Any network on iDRAC7 setting will take 30 to 60 seconds to apply. Can you wait 60 seconds and refresh the page and see if the changes are applied. There is no need to reset the iDRAC to apply the setting.

• iDRAC communication problems 6

  Recently, I tried an upgrade of an old R610 iDRAC6 firmware. Well, everything went wrong. It was done to the place where he was just download the new BIN file before I said to update. It is just hung to 65% for hours until I have to give up. I tried a racadm racreset but he showed:

  ERROR: An update is currently underway. Impossible to reset the RAC at this time.

  SO I deciede to stop the server, unplug it and then empty the 'flea' in operating power in the power button for 10 seconds. I then plugged it back in and waited a little before turning it back on.

  Then, it's really fun when I saw this on the POST:

  The remote access controller initialization...

  iDRAC Configuration Utility 1.54

  Copyright 2010 Dell Inc. All rights reserved

  iDRAC6 failure of Communication.

  The attention! iDRAC6 not responding do not. Reset.

  Then it restarts and then it showed:

  The attention! iDRAC6 not responding do not. Poer required exceed the power of the power supply.

  Change! Continuous start system accepts the risk that the system can turn off without warning.

  Strike F1 key to continue, F2 to run the system setup program

  I can possibly get into the OS and I try a racadm racreset, and it gives me the same warning as before update and this:

  IMPORTANT NOTE!

  FCAC is unable to communicate with the BMC. This condition can occur because of (1) any BMC is present, software components related to IPMI (2) missing or dysfunctional. Features CARS depend on BMC connectivity in order to work properly, and you can see failures as a result.

  I tried all the suggested 'fixed' this page, but it is still dead apparently: http://en.community.dell.com/techcenter/systems-management/w/wiki/3464.troubleshooting-idrac6-issues

  Is there anyway to force a re-flash of the iDRAC or since I can't still connect with him it's a little dead and now I have close F1 to start my server in the future?

  Hello

  the process has been altered and iDRAC will not be able to reflash, in this case, it will be necessary to replace the motherboard

• port bug console virtual iDrac 2.21.21.21

  Hi all

  We have a R430 with an idrac 8.

  We need to access the virtual console, and for many reasons, it must be that its port is different from the default (5900), let's say 5905.
  Everything works fine with the 2.15.10.10 firmware.

  Today, we updated the firmware with lifecycle controller v.2.21.21.21 and the virtual console a work stoppage: when Java runs, after a few seconds, a warning window appears with the message "the network connection fell.

  We tested it without a firewall or other NAT between, so we think it's a bug of the 2.21.21.21 version.
  With the new version, the virtual console only works if the port is configured to 5900.

  We did a restore to version 2.15.10.10 and everything works fine again, also with a non-standard port.

  Anyone with the same problem?

  Good bye

  Hello

  I just tested it and could not reproduce the problem. Have you been able to reproduce this on another system?

  I would like to start by trying a new port number that has not been used to see if it could be a caching problem. If the problem persists, then reset the iDRAC to default values to generate a new configuration file. The file was corrupted during the update of the firmware.

  Thank you

• PowerEdge M610 - IDRAC update version 3.65 to 3.75 fails

  Hello

  I'm updating the IDRAC6 Enterprise of a PowerEdge M610 Server installed in a M1000e blade chassis. In fact, the version installed is of 3.65 and I try to install the recently published 3.75.

  I have some problems, I tried a few different ways:

  -With "System update utility" R2 2012 Windows

  -L' execute the package "" ESM_Firmware_GR09H_WN32_3.75_A00. "» EXE' of Windows R2 2012

  -Chassis using the payload "firmimg.imc" extract the package management "" ESM_Firmware_GR09H_WN32_3.75_A00. "» EXE ".

  -With the help of racadm and download the payload of the TFTP

  It says update succeeded each time, but the version of the IDRAC is stil 3.65 Build 6. If the update is not applied correctly. Execution of the package "" ESM_Firmware_GR09H_WN32_3.75_A00. "» EXE' from Windows 2012 at the end of the procedure, I get the message "The update completed with success.", but in the same window, a strange message pops up: "device: iDRAC, Application: iDRAC data file not recognized ' (as you can see in the screenshot attached).

  Can someone help me solve this problem. All of the other "Server Update Utility" updates are installed properly.

  Thanks in advance,

  Davide

  Hello Davide

  The first update that you tried to apply may be blocked. Once the update is downloaded to the iDRAC, it should initiate a reboot of the iDRAC to apply the update. I would try to restart/reactivate manually iDRAC. You can use racadm racreset or there should be an option in the SAP to restart/reset the iDRAC.

  I just updated a M610 of 3.65 to 3.75 to verify that the image on our site work properly. I downloaded the self-extracting file image from:

  http://www.Dell.com/support/home/us/en/04/drivers/DriversDetails?driverId=GR09H

  iDRAC6_3.75_A00_FW_IMG.exe

  It should be the same file that you extracted from the package Windows install, but you may want to try a just in case where. Simply run the executable file to extract the files.

  Thank you

  

• Where to configure SNMP on iDrac 8?

  Hello

  We have two new servers and they came on reports of security because their SNMP string has been defined to the Public.

  I connected to the iDrac and went to alerts, SNMP & Email and changed the community string to Public to what we usually use.

  I then ran a racreset command where it had to be reset before it would take effect.

  Our security guys revived its audits and the server is always show Public.

  Is there another place in the interface of iDrac who could have a SNMP settings can I change?

  Thank you.

  Too bad. :)

  We found another parameter under iDrac settings / Network / Services and that changed it too.

• Intrusion status PowerEdge T110 II can not be reset

  Hello

  I have a PowerEdge T110 II which is flashing orange health status indicator. The OMSA, the problem was the intrusion alert. I opened the front cover, but now it is closed. How can I reset this alert? I read somewhere to go to the security configuration of the bios to reset it, but there is no encroachment setting it at all. I even updated the bios with the latest version. Any help much appreciated.

  Thank you

  Lee_Km,

  Normally this amber should go back to blue when the cover is restored. I want to watch updates iDrac on the server as well as access to the iDrac (Ctrl-E) and then clear the logs. If the error reappears, then remove the cover and see if now the Intrusion PIN down sensor manually disables the error. If yes reinstall it the lid and make sure the PIN is depressed and clears the error. If none of this works, you can also try to reconnect cable Intrusion sensors as well.

  Let me know the results.

• T310 without IDRAC6 warns of IDRAC communication failure, unable to access the BMC configuration

  Hello

  I got through my company a T310 which has no IDRAC6 Express card or the company.

  The LCD screen remains white/black constantly (tried with a spare one, same result) and when starting, it signals a failure of communication IDRAC6, which is normal since there is no card, then it restarts once more before entering Windows very well. He never offers me to enter a BMC configuration utility. I tried to reset the settings of the default BIOS nothing helps. OMSA reports no problem. Also updated the BIOS to the latest version 1.8.2 without modification. Fan is very noisy and I understand that by updating the BMC firmware, I have a chance to correct it, but I can't get into any configuration of the BMC.

  In my view, there was a map iDRAC6 before, but it is no longer, so don't know how to clear this error. I read that an iDRAC6 Express card is OPTIONAL, so it shouldn't bother me on this subject.

  ==> I want to erase those mistakes to POST, being able to update BMC firmware (or iDRAC) so that I can get the fan to operate at acceptable noise levels.

  (1) how do the server to understand that there is no. IDRAC whatsoever and give me access to the BMC during POST configuration utility?

  (2) is it normal that the remains of white LCD Panel at any time? Start button / stop works very well, just none of the buttons works, never get any color/light. Is it possible that it is controlled by the IDRAC/BMC, which, in its current mess, can't drive? I understand that the LCD comes with the option Connect hot (not sure why btw), so that I think it should work regardless of the IDRAC are there or not.

  I'm ready to buy an IDRAC6 Express card if there is a good chance that he will address this problem by eliminating the communication error and perhaps give me access to the config of the IDRAC. But I would really like to understand what's happening before you spend more money on it.

  Thank you!

  Max

  Hi Max,.

  The question might actually be caused by a problem of motherboard, a functional PowerEdge server without IDRAC should not show the error message, more if the Ctrl + E option is not displayed during POST, it indicates an abnormal start of BMC.

  Are what OS you running on the system? I don't know if you're aware, but the BMC update can be applied to the level of the OS, which are available here:

  http://Dell.to/HIBoTI

  If the system is still under warranty, I highly recommend asking for you assistance and support if a motherboard replacement is required.

  Thank you.

  Best regards

  DC Lim

  Reference Dell | Outreach services social - business

  Follow @DellCaresPro on Twitter: www.twitter.com/DellCaresPro

• Problems updating Firmware 7 IDRAC

  Hi, I had problems with my controller IDRAC PowerEdge T320. It seems to be a known issue, introduced with Firmware version 1.50.50, which is delivered with my machine. Basically, the device signals that all user sessions are used. (RAC0218). I am running Windows 2008 Server R2. To resolve this problem, I find the IDRAC firmware update version for my system. 1.57.57 downloaded the windows EXE file and it ran. The release notes say that a reboot is not necessary. At the end of installation, I got a message in a dialog box. "" Device iDRAC7, Application: iDRAC7 could not access Virtual USB Device "and then the following message in the upgrade of the firmware Installer information window" "" This message can be ignored"with many things on the R2 IPMI driver. My problem is that the Dell OpenManage Server Administrator noted the old firmware version number. I reset the iDRAC from the C: prompt to soft help from "racadm racreset" who have reported success. It made no difference. I emptied my cache of browsers as well. Any ideas how can I know if my firmware has actually been upgraded?

  When I googled the error message my own post came first on the list!  So I thought that I had better do a update.  After finally move to try to solve this problem (again), I opened a case of pension with DELL.

  There is now another more recent version if the firmware of the iDRAC. 1.66.65

  I downloaded and installed, but it failed with the same error on "Failed device to access virtual USB".

  The nice guy of support counted Dell that it is due to an incompatible BIOS version.  I currently have 2.0.22 and the latest version is the 2.3.3.  Then I spoke for her.

  I have successfully installed the BIOS update, requiring a reboot.  I then had another go to the update of the firmware to iDRAC to 1.66.65 and this time it worked WHOO HOO!

  Now wait us and see if real problems connection problems are solved.

  I'm quietly confident.

  Hope this helps someone else

  David