iMac 2009 does not start

Similar Questions

• iMac A1311 does not start, due to no HARD drive

  I have an iMac A1311 that has no HARD drive, so I have a disk HARD of Windows and OS X 10.6.1 discs. Can I use my PC to format the HARD drive and install OS X on the HDD using my PC? iMac will not start cuz no HARD drive

  Unfortunately, you can not. You will need to install a hard drive in the Mac - you cannot install or run Mac OS on a Windows machine (or anything other than Mac hardware).

  In addition, if this one is to end 2011, most likely cannot install 10.6.x as it came without doubt with 10.7 Lion (depending on when it was released or purchased). Mac can not boot from an OS older than what they came with. If it came with Lion, you can install a HDD and then use recovery to format and install the original above operating system (if you downloaded/purchased previously with your Apple ID).

• Mac Disk Manager Pro 2009 does not start

  I have Mac Pro 4.1 2.93 Quad-cord. I look on the net for a solution to the question I had, without success. I recently updated my graphics card to an NVIDIA GTX 960. I connected through HDMI on my monitor. Now, with my old factory graphic card I could just hold the option key to bring up start between 10.11.3 OS and Windows 10 disk management. Now (with the new graphics card), when I take the key Option, it monitor does not turn. But I hear my Mac Pro work. If I let him start normally, without anything hold the monitor will stay a 'sleep' mode until load OSX.

  Could I get some ideas what could be the problem?

  Of course, it looks like you have a PC (not not flashed with Apple EFI).

  A card flashed not Apple will not display anything until loading drivers that is right in front of the login screen.

  This means that you can not use special startups as Option (Boot Manager) or recovery.

• I ran Recover and my iMac still does not start.

  My iMac is frozen and will not restart.  I ran recover and repair disk permissions, still won't start.  The progress bar freezes approximately a third of the way across and stops.  Any ideas?

  Click on the following 3 links & make the necessary:

  On the screens, you see when you start your Mac - Apple Support

  Reset the management system (SCM) controller on your Mac - Apple Support

  How to reset the NVRAM on your Mac - Apple Support

  

• End of 2009 does not start after upgrading RAM

  Just installed 8 GB of RAM from OWC and 240 GB SSD from OWC. At startup, the screen stayed black, the Mac mini beeps (several times), the LED blinked.

  I reversed the positions of chip RAM - same result.

  I replaced the new RAM with the RAM (2x2gb) original. The machine starts perfectly.

  The RAM was purchased from OWC as a Mac Mini 3,1 end 2009 package upgrade that many have commented as works perfectly. My machine doesn't have an update of the firmware. Where from here, please?

  Examine the contacts of the OWC RAM. Compare with work/original RAM.

  Try just a stick of the OWC in each slot and see if a stick is going to work, and in what locations.

  Maybe yo receive a bad stick (or two).

  You can call OWC when available Monday

  I bought the 8 GB (2 x 4 GB) OWC for my Mini end 2009 and it worked without problem.

• MapPoint 2009 does not start when connected to a network

  Hello

  I'm currently trying to install Mappoint Europe 2009 on an HP under Windows XP SP3 laptop. Previously he has worked well with no problems at all - until now. After the installation of Mappoint Euro 2009 application will only work if the laptop is not connected to a network or the DHCP client service is prevented from running by using msconfig (essentially the same thing as pulling the cable). I have now tried this on 2 different laptops and can't seem to find what is causing the problem.

  I tried to install, run as administrator and also to give the administrative user account access, but they all have the same result. As you can tell from above, I have also lived the tedious process of using msconfig and selective startup options after seeing the other messages in relation to similar problems on Win7. So far, no joy.

  At the moment the only way that the user can access Mappoint is to disconnect from everything and remove the cable - use Mappoint and then plug it back in and re-login to all new - which is not ideal.

  It seems to be a bit of a weird error then I was wondering if anyone has found this before or has any ideas?

  Hello

  I suggest you to send your query to the following link.

  http://social.Microsoft.com/forums/is/streetsandtrips/threads

• iMac does not start after the last security update

  Hello

  After the last update my iMac (late 2009, El Capitan) does not start.

  The iMac starts he accepts my user and password entry, the loading bar stops at 80% and then nothing happens... after I turn off the iMac. Repeating this procedure change nothing.

  Does anyone have any advice for me?

  THX

  INTELLECTUAL PROPERTY

  a solution that helped me:

  Re: security update causes damaged Apps

• iMac does not start after 10.11.6

  Since the 10.11.6 patch my IMac does not start with my hub plugged.

  Everyone

  I assume you mean a USB hub? What does do when it's plugged in? It starts successfully when the hub is not plugged? If so, I would say that something is wrong with the hub or there is a problem with the port it is plugged or something plugged into the hub.

  Try to plug it into a different USB port on your Mac.

• 2006 iMac does not start. Help restore

  I have an Intel iMac core duo with iSight and built in disk drive around 2006. It does not start.

  When I turn on, it sounds and passes to the gray screen with the apple logo and a progress bar or a spinning wheel. Then he stops down. I tried all the troubleshooting and nothing works. In addition, I don't have the disks that originally from cane with the computer. So I can't make a diagnosis of the hardware. (Unless someone is willing to sell me their album hehe).

  This problem happened to me in 2012. I had a friend restore the computer to empty the hard disk, then boot from the snow leopard disc and reinstall everything. It worked like a charm.

  In 2013, a disc is stuck in the drive. I have troubleshooted only and nothing has worked. I assumed that the drive is dead and has continued to use the computer without worrying about that. Then, in 2014 someday when I restarted, the disk jumped! I never tested the drive then because I was afraid of another stuck disc. Then, the computer is dead again as he did in 2012.

  SO I know what to do. I need to wipe the hard drive and start over. However, I didn't have a drive. So, I bought one on eBay. When I insert it, the computer enters the disc. I can hear the mechanics works. It ejects even properly. However, I can't boot from the drive. When I start the iMac by pressing option, I don't see the Macintosh, no disk drive.

  My hard drive died? If so, a USB dvd drive would work? If USB does not work, how can I replace the drive?

  Is it possible that I bought a drive bad or fake software and that's why I can't boot from the dad?

  Please help in some way!

  Try a boot sure try safe mode if your Mac does not end commissioning - Apple Support

• Mid 2009 Air. Does not start. Grilled motherboard

  Mid 2009, 2.13 with SSD. I started a Youtube video and the screen froze with lines of color stained and with a strong constant cry. Computer was locked up and I had to leave hard. Now, it does not start at the top. The screen stays black when I push the power button, but the computer will beep and the standby light flashes every 5 seconds. I have to hold the power button down a few seconds as a hard to stop it from. Ideas?

  

  https://support.Apple.com/kb/PH21716?viewlocale=en_US & local = en_US

  Please contact Apple.

  Genius Bar reservation

  http://www.Apple.com/retail/Geniusbar/

• Two iMacs does not start after the 10.11.4 update.

  Two iMacs does not start after the 10.11.4 update.  Progress bar starts moving and then text appears on the black screen saying unexpected sigkill to launchd.  He then gets stuck in a loop trying to start.  Tried to reset the SMC and LANDAU.  Without success.  Started in recovery mode and ran disk utility.  Discs said OK.  Chose to reinstall OS X from the list of options in the recovery mode (assuming it would be 10.11.4).)  Installation is finished but still once does not start.  Reinstalled on 10.11.0 successfully from a USB key and downloaded the 10.11.4 combo updater.  Installation seems to work, but once again, the macs will not start.  Same 'unexpected launchd sigkill' error.  A mac is now back working properly with 10.11.3 the other will be shortly.  Is there a problem with the accession?  Our COMPUTER support use Munki to get updates from one day to the next.  Fortunately, we were able to stop it before the other 20 or if Mac had the same problem.

  More information: two bricks iMacs were late 2013 models.  A 21 "and a 27.  We have just updated a test iMac which was a late model 2012 using the 10.11.4 combo updater.

• My iMac does not start correctly. Instead, I just a gray screen. Safe mode starts, it's ok. No problem. So I ask what next step can I try? Thank you very much

  My iMac does not start correctly. Instead, I have a gray white screen. Safe mode starts, it's ok. No problem. But not in safe mode, only grey screen again.  So I ask what next step can I try? Thank you very much and sorry for my bad English.

  Reinstall El Capitan without erasing the drive

  Make sure that you have a current backup before continuing.

  HD recovery start:

  Restart the computer after the ring, press in and hold the COMMAND and R keys until the menu screen to appear.

  Repair

  When the recovery menu appears, select disk utility and press the continue button. Disk utility charges and select Macintosh HD entry indented from the list on the left.  Click the first aid tab in the toolbar... If disk utility reports any errors that have been corrected, then re-run first aid until no errors are reported. Wait until the operation is complete, then quit disk utility and return to the main menu. Select restart from the Apple menu.

  Reinstall OS X: Select reinstall OS X and click on the continue button.

  Note : You will need an active Internet connection. I suggest to use Ethernet if possible because it's three times faster than Wi - Fi and more reliable.

  In the future please post in the appropriate forum. Your question is not related to the developers forum. I will take care of moved it.

• Creative cloud app does not start on my imac.

  Hi community

  Creative cloud app does not start on my imac. Once she appeard on the bar menu, but as soon as I started to open a session he disappeard. Anyone know this? I use one I use OSX on an iMac 5K 10.11.3 ultimo 2014.

  Reto

  Just for confirmation, enable the account of Root user and you connect to same and try to launch Adobe Creative Cloud application and check. We can turn off later.

  Let us know if you are able to launch the app or not.

  Root user account activation step:

  
  

  OS X Mavericks: enable and disable the root user

  (Applies to Yosemite / El Capitan way)

  

  

  How to connect as root

  1. If you are connected, choose quit from the Apple menu.
  2. If you connect from a list of names of users with pictures, click on the other.
  3. In the name field, type: root
  4. In the password field, type the password that you set when you configure the root user account.

  

  Once you connect to the Root account try to launch creative cloud application and check.

• I'm using Photoshop CS4 on an iMac with OS Lepord of snow.  Recently, I had to do a fresh install of the OS software, then brought back all my Apps, etc. back using Time Machine.  My problem is that now my Photoshop does not start and gives me a messa

  I'm using Photoshop CS4 on an iMac with OS Lepord of snow.  Recently, I had to do a fresh install of the OS software, then brought back all my Apps, etc. back using Time Machine.  My problem is that now, my Photoshop does not start and gives me a message to contact Technical Support with error # 150:30... What should I do now? @

  You must click on this link 150:30 blue and start with message 11.

  Don't forget to leave a space after sudo python before submitting the script.

  Remember that you will not see your password when you enter it when calling to make.

• It seems that there are updates but AppStore does not start

  It seems there are updated but does not start AppStore. Someone at - it an idea how to solve this problem. My iMac restart does not solve the problem.

  I am running OS X El Capitan 10.11.4

  THX in advance

  Select the text below, go to the Safari menu > Services > reveal in Finder.

  ~/Library/preferences/com. Apple.AppStore.plist

  Remove the "com.apple.appstore.plist" file and then restart your Mac and try again.