iMac restarts after the first start since 10.11.6

Similar Questions

• My new Macbook Pro backup in a time Capsule with 2 iMacs. After the first incremental backup but backup every now and again he returned to the backup of the entire drive, why is - this

  My new Macbook Pro backup in a time capsule, as well as 2 iMacs. After the initial backup, it seemed incremental backup but from time to time, he performs a full backup why, is it?

  time to time, she performs a full backup

  What evidence are you using to decide that she performs a full backup?

• iMac restarts after the osx update

  Hi my son has an iMac (mid-2011 Office), and there is an OSX update it will update, but then goes to a screen gray white and just sat there. I've left overnight and does not finish the installation and come back to life.

  I tried to reinstall the operating system via CMD R and I tried first aid on the hard drive.

  If I reinstall the iMac from the time machine backup recovers OK, but I can't get the updates of the OS on the machine.

  So my question is that someone has an idea what could be the cause?

  I contemplate wiping the HD and basically start again, but I have to reinstall MS Office and his Steam account

  Any advice would be welcome

  Your Modem may be loss of connection? Are you using Wifi?

• Partition recovery system fails after the first start

  I just purchased and receive the laptop next: Pavilion DV7-6C95DX. I went through the Setup program and then created recovery DVD.

  After playing with him for a short period, I decided to try to restore to factory using the recovery partition and F11 State when starting.  This started the Recovery Manager, which (according to his Checklist), reformat the Windows partition, copy the files required and restored the file on the hard drive.  Then it prompted me to restart and complete the process, which I did.

  When starting, it reported that he immediately reported "Windows could not start...". "Status: 0xc000000f... a necessary device inaccessible."

  I pressed Enter to continue and the screen says "choose one to start operating system... "and he only gave me the option"[active EMS] Ramdisk Options"choose it brings back me to the previous screen and so on.

  So, I tried using the recovery media that I made earlier.  Who started Windows and Recovery Manager reported the following: "this computer does not support the system recovery media. You are not able to restore this computer with the media"there was a code below that read"0110-A6X02UAR #ABA - A6X02UA #ABA"

  Apparently, there are two problems - the reecovery partition does not work and the recovery media does not work.  I don't know if they are related, but in all cases, the computer is now unusable. It's less than a week.

  Thanks in advance for any advice to fix this.

  Hi Lance,.

  This error can occur if there are USB devices or media attached to your laptop cards.  If this is the case, remove all connected to your laptop then repeat the recovery process.

  If the above is not relevant, I would try the following to rule out a hardware problem.

  Before you try the following, make sure you can read the activation code on your label Windows COA (5 blocks of 5 alphanumeric games).

  Assuming that it's just a problem of software with the recovery process, it is a job before right around if you have (or can borrow) an installation disc Windows 7 at retail which is exactly the same version as your OEM installation - IE if your laptop comes with Windows 7 Home Premium 64-bit, it comes to version exact commercial that you would need.

  If you don't have access to a retail disk, you can create an installation disk yourself using another PC - just download the good Disk Image from the link below and use an app like ImgBurn to burn the ISO correctly on a blank DVD - a guide on the use of ImgBurn to write an ISO on a disc is here.  These Images are clean and a well respected source, however there are only limited versions available.

  Windows 7 sp1-iso-official-32-bit-and-64-bit

  Use the disk to perform the installation, enter the activation key of Windows on the label of the COA at the request and once the installation is complete, use ' 'phone Method' described in detail in the link below to activate the operating system -this made method supported by Microsoft and is popular with people who want to just have a new installation of Windows 7 without additional software load normally comes with OEM installations.

  http://www.kodyaz.com/articles/how-to-activate-Windows-7-by-phone.aspx

  Additional drivers, you may need to find from here.

  If this also fails to install Windows, I would simply return the laptop to the retailer, he bought at and get a replacement while you are still on time where it is an option.

  Kind regards

  DP - K

• Windows 7 Pro 64-bit not start after the first update.

  Integrated system:

  Motherboard: Version of the BIOS Gigabyte GA-X58A-UD3R revision 2.0: FA

  CPU: Intel Core i7-930

  Memory: 6 GB Corsair PC3-12800 DDR3 Triple channel

  HD: Western Digital Black 500 GB SATA 3 Gb/s

  Water cooler: Corsair H50

  The operating system has been installed and running perfect. Readers for the mobo has been installed and and all is well. I can see everything on my computer, network, disks, programs, Device Manager and etc.

  First update for the system, only the important updates were downloaded and after the reboot, the system will not start. The system to start repairing the system but found no problem and restart again and return to the screen of system repair.

  The operating system has been installed 5 times and I had the same problem after the first update, the system unbootable. I tried to boot from the Windows dvd, but I had the same problem again.

  Can someone help me with this problem?

  Thank you

  M. Vilela

  Hi Danielle,

  In addition to the suggestion of Rock Star, you can try the following steps and check if it helps.

  Step 1

  You can first try to start the computer in safe mode and check if you can boot to the desktop. Access the link below and follow the steps to boot to the desktop. To boot to the desktop in safe mode keep tapping key F8 during restart. Once you see the option to start in safe mode select and press to enter.

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2

  If you are able to boot to the desktop in safe mode, you can access to view the history of update on your computer and search for the error code and the updates that failed to install and post it back.

  To view the update history, follow the steps below:

  A. open the control panel (all items view) and click the Windows Update icon.

  B. click on the link to view update history.

  To view the details of a single Windows Update. Select and right-click on a Windows Update list, and then click details.

  Step 3

  I would say also allows you to perform a system restore in safe mode to see if you can restore the computer to an earlier date when it was working fine.

  To restore the operating system to an earlier point in time, follow these steps:

  a. Click Start, type system restore in the search box and then in the list click on the system restore program.

  If you are prompted for an administrator password or a confirmation, type your password or click on continue.

  b. in the System Restore dialog box, click on choose a different restore point and then click Next.

  c. in the list of restore points, click a restore point created before you started having the problem, and then click Next.

  d. click Finish.

  The computer restarts and system files and settings are back to the State they were in when the restore point was created.

  Access the link below to learn more about how to repair the operating system and how torestore configuring operatingsystem to a point in time earlier in Windows:

  http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Apps de Metro de Windows 8 Pro cannot connect to internet after the first reboot

  Hello

  I have recently installed Windows 8 Pro x 64 OEM, and I noticed after awhile that my store, Stocks, Weather, News,... cannot connect to the internet more. However, all other applications work.
  Even more strange, after installing all the updates, I noticed that I can navigate with my IE on the desktop, but not a single party of metro?
  Long story short, after several relocations (refresh option), I've noticed as a result of behavior:
  1. during the first start after installation, EVERYTHING WORKS PERFECTLY. I can browse, look at the weather, everything store.
  2. when I restart the computer and any time after that, is STOP WORKING.
  Another thing I noticed was that his (SoundBlaster Audigy) card didn't work the first time, but after rebooting, it worked, so I guess something happened after the first reboot?
  It was a clean install (OEM version) and Windows are activated, and I tried signing in with or without live account (no difference).
  Help me please, since this is quite irritating :(

  Hello

  I finally found the problem.
  The invisibility of the active network has pushed me towards the answer.
  biggest mistake I made was using the option refresh windows, because it was useless for my troubleshooting.
  By mistake I chose my first install, public internet connection and the course of the updating of the system did not ask see me that.
  In defining the private connection after clean installation (No refresh, brute force reinstall) makes everything work after reboot and completely solved the problem for me.
  Why the network does not disappear after reboot? It's something weird, and it shouldn't happen!
  The resolution of network problems found no problem, because the internet connection worked, but he had no problem with no network also appear or metro apps does not.
  This should be corrected, as it would be a great help in this scenario.
  TL; DR: Make sure you set your connection on the private sector, or windows becomes crazy and your metro applications do not work (and I also noticed that visual studio could not deploy projects in this scenario, but that's another story).

• Portege M750 restarts after the standby or Hibernate mode

  Since I remmember I use my laptop with activate the sleep and hibernation features.
  A couple of days, it started not to restart after the sleep or Hibernate mode.

  You have to take the battery or current alternative, then it starts but without taking the sleep/hibernate.

  Another thing is that when you press the switch on the alternating current led, which is normally green button, it flashes yellow with some sort of a code long and short flashes.

  This happens with different OS cause I tried to reinstall and the problem persists.

  > Another thing is that when you press the switch on the alternating current led, which is normally green button, it flashes yellow with some kind of code long and short flash

  I know that if there is a failure of memory the * power indicator * flashes repeatedly on and off the power (0.5 sec) if there is an error in the slot A the indicator would blink twice in orange, and then green.
  If there is an error in the B slot, the LED will Flash orange and green twice.
  If the error is in the two slots, the LED flashes twice green and orange.

  By the way: it's your BIOS up-to-date?

• Satellite P300 itself keeps restarting after the initial splash screen.

  My Satellite P300 itself keeps restarting after the initial splash screen.

  Start-up of the first screen with the F2 and F12 options down is displayed, the screen goes black, then a cursor appears in the upper left corner and flashes once or twice. Then the laptop stops and restarts and goes through the same process again and again.

  That's all with the power adapter is plugged in. If disconnected, he goes through the above process and close with no reboot.

  Any help or advice would be much appreciated.

  Post edited by: aic-poppy

  Start your laptop and enter the settings of the BIOS (F2). Set to its default value. Restart your computer, and press F8 to access the advanced boot menu.
  To start the laptop in safe mode and let us know if it works, try it please.

• Error "Windows has stopped this device because it has reported problems (code 43)" after the computer start in low resolution and remains after the connection

  Original title:

  Problem occurs intermittently, but almost every time at the first start the morning. The problem can be seen during the POST and the rest after logon. After several reboots, he can come good, but at the next restart could be bad. One clue is that the Device Manager said that to display card NVIDIA Ge Force 8400 GS that "Windows has stopped this device because it has reported problems (code 43)." Driver update says I have the latest driver insalled, version 8.17.12.9573. Help, please

  Have you tried to update your BIOS? Are there updates the firmware for your video card?

• Upgrade Windows 8 Pro blocked after the first reboot

  I have a HP Media Center PC m7470n. When I upgraded with Windows 8 Pro disc, after the first reboot, it gets stuck on the Windows form with turning points. He's not going back to XP and when I stop and restart, he goes right back to the same screen. I tried to boot from a hard drive and CD ROM with the disc in. I also tried to do a system restore, but it still maintains just that goes back to the same screen. , I even contacted Microsoft Support and after 1 1/2 hours, I had to let go because I had to go to work and they do not have a solution for me. I am not able to go in Mode safe either. Can someone help me with this update or at least get back to XP so that I can at least use my computer? At the moment I feel that Windows 8 Pro comes to have my computer in an oversize weight.

  Hello

  Thanks for posting the question in the Microsoft Community. If I understand correctly, you can not connect to the computer. I understand that it must be frustrating, but don't worry, we are here to help solve the problem and guide you in the right direction.

  I suggest you follow the steps:

  (a) starting from the DVD of Windows 8.

  (b) click on repair your computer.

  (c) click on troubleshoot.

  (d) click on Advanced options , and then click auto repair.

  (e) follow the on-screen instructions and complete the repair.

  If you are always faced with the question, please respond with more information, and we will be happy to help you.

  Thank you.

• Successive connection LDAP fails after the first LDAP authorization: with wrong password

  Hello
  
  I am currently integration Oracle CC & B utility to LDAP (Sun Directory Server java - SunOne), but I made a post here because CC & B delegates the task of authentication to the server Weblogic (I user WLS version 10).
  
  In Weblogic, I configured two authentication providers:
  1. the principal is the LDAP authentication provider (defined as optional control indicator)
  2. secondary education is the default authentication provider (defined as optional control indicator)
  
  Currently, some users of CC & B are stored in LDAP, and some other (more users system) are stored in the default authentication provider.
  
  To help you make the problem more clear, I did the test with followingscenario:
  1. user LDUser2 (stored in LDAP) login with correct passwrod-> success
  2. the sysuser user (stored in the default authentication provider) connect with incorrect password-> access denied (what is good and normal)
  3. the LDUser2 (stored in LDAP) user login with password-> successful OK
  4. the sysuser user (stored in the default authentication provider) connect with correct password-> successful OK
  5. the user (stored in LDAP) LDUser2 connect with the incorrect password-> denied access, which is normal. However, from this point, the problem starts
  6. the user (stored in LDAP) LDUser2 connect with the right password-> rejected access KO is the problem
  7. connection (also stored in LDAP as LDUser2) LDUser1 with the right password of the user-> big problem of access denied KO
  8. the LDUser7 user (stored in the default authentication provider) connect with the right password-> successful access
  9 restart the server resets the situation, but once a user is stored in the LDAP connection with a wrong password (5 point number), attempts by users stored in LDAP fail.
  
  It seems that after the first LDAP authentication with wrong password, all users stored in LDAP connection attempts will fail.
  
  Help, please.
  Thank you.
  
  Jeffry

  Hello

  The connection attempt is made on console weblogic with the same result?

  If I'm not wrong, until WLS 10.3 it is a problem reported where once the user connects with password and username incorrect, all attempts after that results in the failure of the connection.

  The patch is available with up to 10.3 WLS support

  This might be the question however need to check.

• iPad will not restart after the update iOS9.3. Should force us the reboot?

  iPad will not restart after the update iOS9.3. Should force us the reboot?

  By restart do you average will not turn on?

  There seems to be a bit of a problem past, especially with older models of iPad 2. Some people have reported success after that restore their device via iTunes, for others that it has not worked and all they get is a message "bring it in an apple store.

  Since it affects a lot of people, I think it's safe to say that the problem lies in the range of Apple. But I don't think it is recognized or no matter what put forward fix.

  You can try to restore your device, or you may just be stuck waiting to see if a fix comes out.

  http://support.Apple.com/kb/HT1414

• Windows 7 crashes 5-10 minutes after the game starts!

  Whenever I load my games that all crash after 5-10 min I have all new drivers and all games are compatible... PLEASE TELL ME WAT I'M DOING

  Hi LZYGA09,

  1 you get an error message before or after that you get the black screen?

  You can try the following workaround to find the root cause of the problem:

  Please check if you are facing the same question when working in safe mode.
  Step 1.
  1. reboot your computer.
  2. when the computer starts, you will see your computer hardware are listed. When you see this information begins to tap the F8 on your keyboard key repeatedly until you are presented with the screen Windows 7 Advanced Startup Options.
  3. using the arrow keys, select the desired option of Mode safe.
  4. press the Enter key on your keyboard to start in safe mode of Windows 7.
  5. when Windows starts, you will be at a typical logon screen. Connect to your computer and Windows 7 goes into safe mode.
  6 do whatever tasks you need and when you are done, reboot to return to normal mode.

  Step 2
  If the question had existed in Mode safe, make the boot minimum troubleshooting to find the root cause of the problem:
  Clean clean boot:
  1. click on start, type msconfig in the search box and press ENTER.
  The user account control permission.
  If you are prompted for an administrator password or confirmation, type
  password, or click on continue.
  2. in the general tab, click Selective startup.
  3. under Selective startup, clear the check box load starting points.
  4. click on the Services tab, select the hide all Microsoft Services check box, and then click Disable all.
  5. click on OK.
  6. When you are prompted, click on restart.
  7. after the computer starts, check if the problem is resolved.
   
  If the problem is resolved to check what is the cause of the problem, referring to the link given below:
  http://support.Microsoft.com/kb/929135
   
  8. in addition, you will need to uninstall and reinstall the software problem on your computer.
  Reset the computer to start as usual
  9. When you have finished troubleshooting, follow these steps to reset the computer to start as usual:
  Click Start, type msconfig.exe in the start search box and press ENTER.
  10. If you are prompted for an administrator password or for confirmation, type your password, or click on continue. On the general tab, click the Normal startup option, and then click OK.
  11. When you are prompted to restart the computer, click on restart.

  2. I recommend you to run online Virus Scan to remove any infections, as appropriate.
  Follow the link below to start the free online scan:
  http://OneCare.live.com/site/en-us/default.htm The following thread discusses the removal of viruses and malware online:
  http://social.answers.Microsoft.com/forums/en-us/vistasecurity/thread/ba80504b-61f1-4D71-960f-b561798b7b42

  It will be useful.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Pavilion Media Center does not restart after the full system recovery. get the error code 0 x 4001100200001005

  Pavilion Media Center does not restart after the full system recovery. created recovery disks when purchased new. get the error code 0 x 4001100200001005

  Original title: recovery problem

  Hello

  According to the HP Support Forums, this error may be to do with the hard or for other reasons.

  You never have it replaced with a no HP bought in car?

  Read these threads HP on your error code:

  http://h30434.www3.HP.com/T5/notebook-operating-systems-and-software/recovery-disk-error-0x400110020000-1005/TD-p/22936

  http://h30434.www3.HP.com/T5/desktop-recovery-reply-only/trying-to-recover-an-old-PC-error-code/TD-p/964509

  If the original hard drive, press F11 at startup to start the process of recovery partition HP, did you recovery disks of.

  See you soon...

• URGENT::opening multiple files - i have 3 files in my directory... When I run the code I can open a file and read it... but the while loop get blocked after the first iteration... can someone me help or give some indications

  bbmChatDB of public database;

  public static FileConnection fconnRead = null;
  public static String fileReadData = "";
  public static InputStream is = null;
  data Byte [] = null;
  DataInputStream is = null;

  Here is my code...

  I have 3 files in my directory... When I run the code I can open a file and read it... but the while loop get blocked after the first iteration... can someone me help or give some indications

  try {}

  FileConnection fc = Connector.open("file:///store/home/user/documents/BSM/") (FileConnection); "

  If (fc.exists ()) {}

  Enumeration e = fc.list ();

  While (e.hasMoreElements ()) {}

  System.out.println ("files are:" + (String) e.nextElement ());

  play this file
  StringBuffer stringBuff = new StringBuffer();
  try {}
  System.out.println ("opening file")-;
  System.out.println ("file name is:" + (String) e.nextElement ());
  fconnRead = Connector.open("file:///store/home/user/documents/BSM/(String)e.nextElement(),Connector.READ_WRITE) (FileConnection);
  System.out.println ("data length")-;
  If (fconnRead.exists ()) {}
  is = fconnRead.openDataInputStream ();
  data = IOUtilities.streamToBytes (is);
  Ddd = new String string (data);
  fileReadData = ddd.toString ();
  System.out.println ("length of data:" + fileReadData.length ());
  System.out.println ("read data :" + fileReadData);

  }

  } catch (IOException ee) {}
  ee.printStackTrace ();
  System.out.println ("Exception in the read data :")
  + ee.getMessage ());
  }

  }
  }

  } catch (IOException e) {}

  e.printStackTrace ();
  }

  {Finally

  try {}
  If (is! = null) {}
  is. Close();
  }
  System.out.println ("is closed...");
  } catch (IOException e1) {}

  E1. PrintStackTrace();
  }

  If (fconnRead! = null) {}
  try {}
  fconnRead.close ();
  } catch (Exception e) {}
  System.out.println (try ());
  }

  }

  }

  You can recode this treatment so that it uses only:

  e.nextElement ())

  Once a loop iteration.

  Directly at the start saying something like:

  String fileName = e.nextElement ());

  and use fileName everywhere in your loop.

  Also be aware that printStackTrace() will do nothing in your situation, it only works if you catch Throwable.  So make sure you something output all your catches exception and also have a catch (Throwable t) to catch the things you miss, as follows:

  {} catch (Throwable t)

  t.printStackTrace ();

  System.out.println ("Eception exception:" + t.toString ());

  }

  I think your code is thrown an exception and you don't see it.