Image file capwap IOS corresponding with image Wlc file flash

Similar Questions

• Set of images of Device Manager, but not a valid image of the flash file: / asdm - 512.bin

  I'm putting this new image that I have loaded by ASDM version 5.0 and the name of the image is in my config and I wrote from memory, but all I get is the error message above.

  Hello

  Referring to the new image of ASDM image ASA (pix 7.x) file?

  Anyway, if it doesn't work, try reinstalling the image again through CLI.

  a. to load image PIX 7.0-> copy flash tftp:

  b. to load ASDM image-> copy tftp flash: asdm

  * Make sure that the tftp Protocol is ready, and probably to remove previous load from file.

  Once the installation is completed and after reboot, check the loaded file using 'sh version' command. You can also use 'sh bootvar' command to check system startup properties and image which is responsible for operating the unit.

  Rgds,

  AK

• Laptop HP 15 15 - r014TX: I have 8.1 windows recovery image in a flash drive, I want to burn the DVD recovery

  I have the recovery windows 8.1 image in a flash drive, I want to burn the recovery in dvds.by error I've removed the drive from the partition that was on my computer, please help me with this problem.

  rohit1317 wrote:

  I have the recovery windows 8.1 image in a flash drive, I want to burn the recovery in dvds.by error I've removed the drive from the partition that was on my computer, please help me with this problem.

  Hello

  Unfortunately, you can only create 1 set of recovery media.

  Copy and burn recovery USB DVD and then using DVD to make the system recovery will not work.

  What you can do is to backup all your data on an external drive. Do a factory reset with the USB of recovery to recover all partitions including the recovery on the HARD drive partition.

  Concerning

  Visruth

• I can not compile for iOS more with Flex and AIR 3.8

  Hello team Adobe and others.

  I use for my business framework 4.10 Apache projects Flex and adobe Air 3.8.

  I always had problems to compile and publish iOS apps (with Air 3.5 front), but with AIR 3.8, it was a miracle, I compile my projects without error on Windows... until today.

  I am running this command in DOS to compile my project:

  "C:\Program Files\Java\jre7\bin\java.exe" - jar "C:\Program Files\Adobe\Adobe Flash Builder 4.7 (64 Bit)\sdks\4.10 - 3.8\lib\adt.jar AIR ' - package - target the ipa-app-store - hideAneLibSymbols non - implementation service-profile 'S:\Directory_to_MobileProvision.mobileprovision' - shops pkcs12 - keystore"S:\Directory_to_Certificats_ios.p12"- storepass my_private_password Proginov_FVTE_V45.ipa Proginov_FVTE_V45 - app.xml active com config_app.xml [email protected] Proginov_FVTE_V45.swf - extdir"S:/Directory_to_ANE/air_3.8_pnv_3.00 ".

  And I get this result after 1 hour of compilation:

  

  If you want, I can send you my file bin-release-temp and DONKEY to try for yourself, but I need to private messaging, because I don't want to publish my project private to everyone.

  Thank you

  Could you please try the growing size of the java heap in your order.

  for example, "C:\Program Files\Java\jre7\bin\java.exe" - Xmx2048m-jar...

• Area of the image in CS6 flashing

  As in the title, in Photoshop CS6 I seem to be getting a lot of blinking of the area of the image. By "flashing", I mean that the area becomes completely black for the fraction of second enough often. It seems to be somewhat influenced by my actions, as when I alt - tab on photoshop with the window always visible, the image area stops flashing.

  Card of my PC:

  Intel Core 2 Quad Q6600

  AMD Radeon HD5770

  6 GB OF RAM

  Windows 8

  EDIT: I seem to have found the thing causing the flashing, it seems to happen only when an image is selected. Still no idea why it goes well.

  Does make a difference if you set the mode to basic under Edit > Preferences > Performance > CPU graph use > advanced settings > Drawing Mode?

• trigger events based on the current image of the flash animation

  I have a Director with video qt project where are trigger actions based on specific times in the video (movietime and/or duration). I update this project in order to use flash instead of quicktime video.

  To facilitate the development and coding changes minimal if all goes well, I would like to keep this similar functionality, but I can't figure out how to capture the current image of the flash movie sprite.

  Can anyone help? or provide a workaround solution?

  I can't figure out how to capture the current image of the flash movie sprite.

  You were near. Try one of these:

  put sprite("flash").currentFrame
  -- or
  put sprite("flash").frame
  

• Check dynamic image loaded into Flash?

  Hello world
  
  Does anyone know a good tutorial to load in an external jpg in Flash where actionscript is to check the time / date of the image in the folder with the one in flash and update if it is a newer image?
  
  Your help is really appreciated :)

  In fact if all what you need to do is to check if the image has changed (different pixels) then you can use the BitmapData class to compare the current and new images.

  Create an object BitmapData of the current image (which is loaded in current_mc) and the new image (loading in new_mc). Then compare the two. If their different, then you can update current_mc by the new image.

  If I get some time, I'll try and create an example - unless someone has one sitting?

  See you soon,.
  OSH...

• Problem with iMac Start Up - file flashes and no sound

  Hello.

  I was using my iMac mid 2007 earlier today, when he started to slow down, with the color wheel appearing whenever I tried to click on something.

  I left only for a few seconds, thinking that he just needed some time, before the screen went all white. I turned off the computer in decision-making, tried to restart, but after several attempts to turn it back on, all I get is a white screen and a file flashing with an exclamation mark on the subject.

  I tried the cmd + R trick, but it does not work and there is also no startup sound, that is, or so I read, when you're supposed to press these keys.

  According to me, the iMac has been updated to OS X El Capitan (10.11), otherwise this was Yosemite, but I don't know what level of the update, I was on. I can't access the computer for you tell all the other details, but I'm sure he had a memory of 4 GB, I have improved the memory myself.

  Thanks for any help you can give me.

  The flashing? means that it cannot find your hard drive. Looks like your hard drive is faulty / failed.

• IBooks on ipad pro crash after IOS updated with 9.3.1.please

  IBooks on ipad pro crash after IOS updated with 9.3.1.please

  I have the same problem after update 9.3 OS on my Ipad 2... Crashing in IBooks. PDF and missing books. I have access to my books for about a minute before it crashed.

  It still occurs with the 9.3.1 update.

  I don't really know where to go then except put it there the 9.3.1 upgrade did not fix my problem.

  Thinking that I might have to consider for an Apple Tech which is an expense I really don't think I should have to bear, because I did not cause the problem that everything worked fine with my iBook before upgrading the OS 9.3.

  Thank you

• With the help of new access points with old WLC 4100; LWAPP layer 2 switching 3-tier

  Hi all

  We currently use two solutions Wiresless LAN - a 10 AP1230 access points-based autonomous (5 years) and a solution based on a Cisco WLC 4100 (4112, running 3.2) with 12 AP1010 LWAPP access points.

  First thing, we are considering to replace the stand-alone solution with the WLC one. However, I'm not sure if we can use the new access points such as the LAP1041N or the LAP1252G with our current 4100 WLC. Access reported data sheets 'Cisco Unified Wireless Network Software Release 7.0 or later version' 'software '. Does this mean that these access points can only be used with controllers running 7.0 or later?

  If we are unable to use the new access points with our current WLC and need to buy a new controller: can we use access points AP1010 current with a new WLC as the Cisco 4402?

  Second thing, it is that we want to expand the networks configured on the WLC 4100 to another site that is connected via VPN wireless. Wireless Setup guide indicates that the LWAPP mode can be changed from Layer 2 to 3 layers so that the access points can be configured with an IP address, which allows you to place access points basically anywhere as long as IP connectivity exists between the AP and the WLC.

  Y does it as described in a document with the change of mode LWAPP layer 2 to 3 layers? Or ist just the following steps (if I understand correctly):

  -Change the Mode of Transport LWAPP on the controller of layer 2 to 3 layers

  -Creation of a PA-manager interface with an IP address in the same subnet as the management interface (tried that, without changing LWAPP mode transport first and not was not possible - error)

  With regard to different sites:

  -Configure option DHCP 43 with the IP address of the WLC or DNS with CISCO-LWAPP - CONTROLLER.localdomain

  -Make sure that the interface ap - manager can reach points on the different site

  Is it really just as simple as that? All information about it is very appreciated!

  / edit: I would also like to know if the 1260 series access point are backward compatible with 802. 11B. Whereas it is stated in 1040 and 1250 for example series data sheets, it is not particularly mentioned in 1260 data sheet.

  Thank you

  Michael

  Well, let's start with the simple question/answer

  With regard to different sites:

  -Configure option DHCP 43 with the IP address of the WLC or DNS with CISCO-LWAPP - CONTROLLER.localdomain

  -Make sure that the interface ap - manager can reach points on the different site

  Yes, it's as simple as that.

  As for other issues, looks like you would be better served with a forklift upgrade.  New controllers and new AP.

  Now, the AP 1230/1240/1250. all work on the 4.2, 1140 code starts with 5.2 and 1040/3500/1260 are 7.0

  The AP 1000 series is not supported after 4.2 code.

  Refer to here for the complete list of the AP and taken codes supported:

  http://www.Cisco.com/en/us/docs/wireless/controller/release/notes/crn7.0.html#wp610751

  From what I see, the 4100 is not supported after the train of 3.2.

  So, it really depends on what you are trying to accomplish with the upgrade.  If you are looking for a 80.211n support, you really want to be 5.2 or better, we had some problems with MRR + 40 Mhz channels, 4.2, 5 GHz band only.

• ISE 1.2 - begging CWA provisioning with anchor WLC

  Hi all

  Having a problem with supply begging via CWA on a controller of the anchor. I am able to connect through CWA and authenticate etc no problem, but when the device registration page it says "cannot connect to the network at this moment" - the mac address is filled but the said button try again. Once I click on retry it cycles back to the original comments Portal login page. In the section reports the begging failed provisioning message is "error trying to determine access privileges: failed to get the host name of the session cache."

  I tried the same policy without the anchor (ie the local controller) and it works perfectly. Interestingly enough if I manually register the device then connect first the portal comments, that it allows me to click on register and proceed to the provision of begging. I also tried installing anchor using peap and NSP redirection - this also works perfectly.

  I can confirm beforehand that firewalls, etc. is not a problem with permit IP any one between all parts of work - no blocks without drops etc. Politics is the standard CWA trustsec installation with Enable ticked self-supply. For what it's worth, I am absolutely confident with the config having deployed before - but without a controller of anchor.

  Stephen,

  I have worked with TAC customer account team to find a solution.  The problem is with the WLC anchor and the session not replicated.  I was able to get around by disabling account management radius for the ssid on the controller of the anchor, but when we look at the bug looks like an alternative solution is to disable fast switching ssid, which could cause problems with BYOD worldwide double ssid.  I still do test, but the accounting change seems to have resolved.  Bug ID: CSCui38627

• Find invalid date and month not corresponding with the calendar

  Helllo,
  
  I want to find the line to invalid date, which do not correspond with day and month.
  
  Also, the program should capture the data if the year < 1900
  
  Thanks in advance
  
  
  
  with xx as
  (select 101 as the ID, May 24, 1899 ' than double create_date)
  Union of all the
  Select 101, 32/03/2012 "of the double
  Union of all the
  Select 102 30/02/2012 "of the double
  Union of all the
  Select 101, 29/02/2013 "of the double
  Union of all the
  Select 102, February 28, 2013 "of the double
  Union of all the
  Select 102, 24 January 2012 ' double
  Union of all the
  Select 101, ' - 11/22 / 2012 "of the double
  Union of all the
  Select 102, ' 05/42/2012 "of the double
  Union of all the
  Select 101, ' 01/72/2012 "of the double
  )
  
  Select * from xx
  

• With the help of Flash/AS as a possible model?

  Hi all!

  I am very new to flash (just started last week) so please bare with me if this question sounds stupid ridiculusly

  I wonder if it is possible to use Flash/AS files as 'model' - in other words, we have the website http://shop.variuscard.com and the header is subject to change according to the category of product, you click on in the shop. We will have about 10 categories and each will have a different product displayed in the flash movie, but "background" should remain the same.

  Now, in this case, I need to change something (say the logo goes from blue to red and the particle size and shape) I don't want to change all the 10 or more files again. So is it possible to use the "basic" flash file as a template, which means - position of the Logo & shadow and the code of the particle and just change the variables photos and stuff inside the categories? I got this card red-printer as a sample of the category of card-printer for example.

  Thanks in advance!

  There are several ways you can manage a template file.  The more modern method is probably to have the data file that defines certain characteristics of the contents of this file, such as the image of the logo it uses, the title appears, where things are placed, etc.  Then you have your file Flash load/dynamically adjust content by what dictates the data file.  So your data file might specify the name of the image logo file and where it is planted and the file could use this information to load this file and place it where it will.

  Another thing, you can do use the FlashVars parameter that allows the embed code.  So if you had the same banner in the same website on different pages or sections of a page, you can use the FlashVars to indicate some settings in each file must use to decide what content it must make use of.

  The combination of these approaches can alow you only have a Flash file and a data file that you are editing as needed.

• "When you leave the computer unattended for ten minutes an error pops up that says cannot find the .ocx file flash file.

  "when I return to the computer I have x try it and if I walk for ten minutes and more onus does not find the file flash.ocx.

  Hello

  1 how long have you been faced with this problem?
  2. don't you make changes on the computer before this problem?

  Flash.ocx is a flash plug-in which is responsible for adobe flash player run on the system

  Step 1: Maybe it's that the flash drive is gone corrupt. I would reinstall it again on the system and check if the problem is resolved.

  Before installing Adobe flash player on the system, make sure that all previous versions of Adobe flash player uninstalled from the system. Download the utility on the site mentioned below, install it and run it on the system.

  Uninstall Flash Player
  http://kb2.Adobe.com/CPS/141/tn_14157.html
   
  Once you uninstall Adobe and then try to download Adobe Flash player Adobe website form. Click on the link below.
  http://get.Adobe.com/flashplayer/

  Step 2: Check if the problem persists in the clean boot state.

  Put your boot system helps determine if third-party applications or startup items are causing the problem.

  Try the procedure described in step 1 in the section below to put your computer in clean boot mode.
  http://support.Microsoft.com/kb/310353

• I'm trying to restore my win7 with HP USB recovery Flash Disk, I get the following two messages

  I'm trying to restore my win7 with HP USB recovery Flash Disk, I get the following two messages:

  "Do not create C:\Users\User\AppData\Local\Temp; c:\arc\01Script\FormatUFD.SP' and the messsage "Fail to create.

  How to port HP_recovery in car to my flash drive?

  Windows 7 x 64, HP G62-144DX

  Hello:

  I can't help you with this specific issue, but if you can get it is resolved and you can read the product key 25 character Microsoft Windows on the bottom of your PC, do your own installation of W7 media to reinstall W7.

  Here's how:

  If you can read the Microsoft windows 7 25-character product key, you can download simple Windows 7 ISO files to burn on a DVD for the version of windows that is installed on your PC, and which is listed on the Microsoft COA sticker on your PC case.

  Burn the ISO with the option to burn the ISO on your DVD burning program and burn it at the slowest possible speed that will allow your program. This will create a bootable DVD.

  Or use the installation of Windows 7 USB/DVD tool to compile the ISO file that you download from Digital River. Link and instructions below. You need a 4 GB flash drive to use the USB compilation method.

  http://www.microsoftstore.com/store/msstore/HTML/pbPage.Help_Win7_usbdvd_dwnTool

  Use 25 characters on the PC product key to activate the installation.

  The key will activate a 32 or 64 bit installation.

  Then go to the support of the PC and driver page to install the drivers you need.

  Link to downloads ISO of W7 is below.

  http://www.mydigitallife.info/official-Windows-7-SP1-ISO-from-Digital-River/

  Paul