Images ASA

Similar Questions

• Update image ASA

  Need to improve my image of Cisco ASA 5510 of asa821 - k8.bin to asa903 - k8.bin with the following license. Do I have to purchase a new license with upgrade of the image?

  #sh version

  Cisco Adaptive Security Appliance Version 8.2 software (1)

  Version 6.2 Device Manager (1)

  Updated Wednesday, 5 May 09 22:45 by manufacturers

  System image file is "disk0: / asa821 - k8.bin.

  The configuration file to the startup was "startup-config '.

  TMN-5510 294 days 2 hours

  Material: ASA5510, 256 MB of RAM, processor Pentium 4 Celeron 1600 MHz

  Internal ATA Compact Flash, 256 MB

  BIOS Flash M50FW080 @ 0xffe00000, 1024 KB

  Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)

  Start firmware: CN1000-MC-BOOT - 2.00

  SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03

  Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.04

  0: Ext: Ethernet0/0: the address is *.

  1: Ext: Ethernet0/1: address is *.

  2: Ext: Ethernet0/2: address is *.

  3: Ext: Ethernet0/3: address is *.

  4: Ext: Management0/0: address *.

  5: Int: internal-Data0/0: the address is *.

  6: Int: internal-Control0/0: the address is *.

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 100

  Internal hosts: unlimited

  Failover: Active/active

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 2

  GTP/GPRS: disabled

  SSL VPN peers: 2

  The VPN peers total: 250

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect for Linksys phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  This platform includes an ASA 5510 Security Plus license.

  Series number:

  Running Activation Key: ****************************************************************************

  Registry configuration is 0x1

  Last modified by enable_15 to the configuration 22:29:35.255 * Friday, April 4, 2014

  -----------------------------------------------------------------------------------------------------------------------------------------------------------------------

  Need help

  > Do I need to purchase a new license with upgrade of the image?

  NO.

  But check the:

  1)

  https://supportforums.Cisco.com/document/48646/ASA-83-upgrade-what-you-n...

  (2) to migrate the configuration of 8.21 to 9.03 asking TAC cisco help

• ADSM 5.0.5 not loaded with image ASA 7.0.5

  Hello

  Having an ASA5520, who was running with the image: asa704-4 - k8.bin and the ADSM: asdm504 - 2.bin

  I improved the image in version 7.0.5 and the ADSM in 5.0.5

  The ASA boots properly with this new version 7.0.5, but still start with the asdm504 - 2.bin ADSM and not the asdm505.bin

  In the configuration, I have the following initialization variable:

  boot system Disk0: / asa705 - k8.bin

  Disk0: / asdm505.bin starting system

  So, I would like to know why the ASA 5520 does not accept the ADSM file at startup.

  PS: the ADSM file in the flash size is: 5823304

  You do not want to have the boot system command reference the asdm .bin file. the correct command to the asdm file is:

  ASDM image disk0: /.

  Make sure that you remove the start control system of the asdm file references. you want to just start the file asa704.bin.

• Set of images of Device Manager, but not a valid image of the flash file: / asdm - 512.bin

  I'm putting this new image that I have loaded by ASDM version 5.0 and the name of the image is in my config and I wrote from memory, but all I get is the error message above.

  Hello

  Referring to the new image of ASDM image ASA (pix 7.x) file?

  Anyway, if it doesn't work, try reinstalling the image again through CLI.

  a. to load image PIX 7.0-> copy flash tftp:

  b. to load ASDM image-> copy tftp flash: asdm

  * Make sure that the tftp Protocol is ready, and probably to remove previous load from file.

  Once the installation is completed and after reboot, check the loaded file using 'sh version' command. You can also use 'sh bootvar' command to check system startup properties and image which is responsible for operating the unit.

  Rgds,

  AK

• PIX / ASA 7.0

  Is the PIX v7.0 OS the same OS that runs on the ASA? Configurations are portable between the two devices.

  They are essentailly the same thing, even if you can not put a picture of pix on a SAA or vice versa. PIX is Magi begin «pix...» ', images ASA... Well, you can guess.

  There are some differences due to material - an ASA does not have a serial port for failover (to use LAN-based failover), he did not FO/R/UR and interface IDS are different.

  But in terms of NAT, ACL, itineraries, opposed groups etc. is the same thing. You can config port but attention config interface and failover.

• ASA fire threat defense unified image (DFT)

  Hello

  Cisco would anyone please explain what is this image? And what parts of the SAA does include? Can do VPN/Anyconnect?

  ASA OS is being retired?

  Concerning

  Fix. From now on, not all features are available, but they will eventually. The current image is released 6.0.1 that didn't anyconnect. Please rate the answer if it helps. Thanks Yogesh

• Version of the Cisco ASA images.

  Hi all.

  Anyone can check my perception on the differences between these images?

  asa933-7-lfbff-k8. SPA

  asa924-5-smp - K8.bin

  asa924-5 - k8.bin

  I guess that lfbff is for the X 5506 and 5508-X with firepower onboard services.

  What are the supposed to a user of the image of SMP (Symmetric MultiProcessing)? The ASA 5506-X and 5508-X would be able to run the SMP image?

  Witch platforms use the image without any abbreviation?

  Any clarification would be greatly appreciated.

  Concerning

  Hello

  Yes you are right.

  asa933-7-lfbff-k8. SPA - this would be used on active firepower ASA for example 5506-X etc.

  asa924-5-smp - K8.bin - this is used for devices using Multi hearts.

  Anything with "smp" in the file name is only compatible with the X-5500 series. The "smp" means symmetric multiprocessor and requires a multicore processor.

  asa924-5 - k8.bin - it is used for legacy of the ASA using single cores.

  Kind regards

  Aditya

• AIP - SSM recreate the image in secondary ASA 5500 (failover) with virtual contexts

  Hello guys,.

  The scenario is as follows:

  2 ASA 5500 with virtual contexts for failover.

  The ASA elementary school has the work of the AIP-SSM20.

  ASA school (which is in active / standby) has its SSM20 AIP to work now and everything is in production.

  Someone tried to configure this 2nd AIP - SSM, changed the password and lost, so I tried to re - the image (without authorized passage recovery), but the connection fails on the TFTP server, where is the image of the AIP - SSM.

  Now questions, documentation Cisco re-imaging view orders under ASA #.

  but as this scenario has several virtual contexts the ASA # shell contains no IP address as you know (which I suppose is the reason why the ASA cannot download the image from the TFTP server) and switch to another context (ASA / admin #) re-imaging commands do not work (hw-module module 1... etc...).

  What is the solution? Is there documentation for it (with security contexts)?

  Thank you very much for reading ;) comment on possible solutions.

  Yes,

  Some things to keep in mind.

  (1) run 'debug module start' on the SAA before running the command "hw-module module 1 recover boot. This will show you the ROMMON of the MSS output as it tries to make the new image and you can look for any errors.

  (2) before trying to download from the SSM, first use a machine separate download tftp from your laptop. This will ensure the TFTP on your laptop works and confirm what directory (if any) that you can use as the file location.

  (3) if the tftp download does not SSM, then the SSM is unable to properly connect to your laptop. You need a crossover cable to connect your laptop to the SSM. If you have a crossover cable, then you could try to connect the MSS and your laptop to a small hub, or configure a new vlan on your switch with only 2 ports and connect the MSS and your computer laptop this vlan 2 port.

  (4) also try the download first at the end of the gateway to 0.0.0.0 since your laptop and the SSM will be on the same subnet. If this does not work then you can try a non-existent 30.0.0.4 address as gateway.

  (5) understand that the IP address that you specify for the MSS using the command "configure the hw-module module 1 recover" is just temporary for download. Once an image is installed, then sitting at the module and run the "setup" command in order to configure the permanent address you want ure on external port of the SSM. This address in the "setup" command can the same as that used in the command 'get the 1 hw-module module configure' or a completely new (as in your case). Just make sure that you connect to the network just to what address you give.

• ASA image upgrade

  Hi all experts

  We now use asa 5510 with asa image version 8.0 (4) (256 MB of memory). Do you think we can improve the version asa image of 8.0 (4) ASA 9.1.3? functioning after upgrade?

  Hugo

  Sorry, but you can't. The ASA 5510 requires 1 GB of memory to run ASA 8.3 or hgher software. Reference.

• Transfer the image to the ASDM ASA on the anyconnect VPN

  I'm relatively new to the ASA firewalls.  My previous experience of firewall is a firewall provider.  I work with an ASA 5515 - X running ASA 915 and ASDM 713.  I connect Windows 8 and therefore improve the ASDM to 731.  I've done it before no problem.  My problem with this particular update is that I really need to download the image to a VPN connection.  I can't configure a NAT device on my end to allow the ASA to connect to my public IP address - so I can connect to the ASA via anyconnect.  I can't SSH in public IP address of the ASA (for now) but I can't transfer the asdm image obviously not my public IP b/c I have no NAT on my end.  So I connect my PC to the anyconnect service and get an IP VPN.  I need to run the command:

  copy ftp://user: [email protected] / * *//asdm-731.bin disk0:

  I get the following output: for access to the ftp://user: [email protected] / * *//asdm-731.bin...
  Error opening % ftp://user: [email protected] / * *//asdm-731.bin (Permission denied)

  Anyone know good ways to solve this CLI only?

  Thanks for your help.

  Zach

  Looks like a FTP permission problem. The user has read access? Also, make sure that your 8 victory is tuned for FTP requests on map virtual VPN.

  one of the other option is to use a host of jump in your lan behind asa and open the asdm from there, using asdm, it will be easier to copy the file to asa flash.

• ASA 5520 Boot Error: Boot Image too large

  Hello

  I had 2 ASAs in an Active/Active configuration, but when I deleted the current config and passed back to the simple mode I get an error message at startup ' error: Boot Image too wide. " I've not seen any discussions or discussions on this matter. I am not sure, but I think the best way to solve this problem would be to take the configuration of starting of my still working ASA... send it to a tftp server and put it back on my ASA that will not start. If anyone has experience this problem or can give me a definitive answer regarding a possible solution please post a reply.

  Thank you

  Chris Bailey

  You can download the file from the following url. But you must log in using your ID EAC:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/ASA

  The two download asa and asdm.

  Once you've got the file asa, load everything first to your ASA. Restart, and then go to the CLI. Load the asdm by using this command:

  copy the flashftp://your-server-IP/pathtofile t: / asdm - 511.bin

  http://www.Cisco.com/en/us/partner/products/ps6121/prod_release_note09186a00805b8543.html#wp37943

  http://www.Cisco.com/en/us/partner/products/ps6120/products_field_notice09186a0080655b8b.shtml

  http://www.Cisco.com/en/us/partner/products/HW/vpndevc/ps2030/products_tech_note09186a00804708d8.shtml

  Good luck.

  Rgds,

  AK

• How to configure ASDM Cisco ASA 5505

  I have a Cisco ASA 5505 firewall, and currently it is a command-line firewall. I want to configure ASDM so that I can use it as a Web based GUI interface.

  I don't really know what to do. Can someone help me please how I can configure ASDM on my firewall.

  Kind regards

  Naushad Khan

  Hi Naushad,

  First of all, must load the image ASSDM on SAA and then use the command:

  ASDM image dosk0: / asdm645.bin (if the image name is asdm645.bin)

  then:

  Enable http server

  http 10.0.0.0 255.0.0.0 inside (if your machine is 10.0.0.0 subnet behind inside the inetrafce)

  Go to the machine, open a browser and type:

  https://

  It will open the GUI.

  Thank you

  Varun

  Please evaluate the useful messages.

• Updated AIP-SSM-10 on ASA 5510

  Hello

  I want to upgrade the IPS module in an ASA 5510, and I have a few questions. The AIP - SSM is running E3 479.0 1.0000 and I have a valid account of the ORC etc for this.

  1. What is the version of the software on the question of the ASA?
  2. When I look in the software downloads< ips="" there="" are="" .pkg="" and="" .img="" files.="" i="" want="" to="" upgrade="" to="" 6.3(3)e4.="" do="" i="" have="" to="" re-image="" the="" ips="">
  3. AFAIK redefinition to wipe the device so I just reload the config after, right?
  4. I guess I can apply any update after going to E4?
  5. Can you give me links for this upgrade?

  see you soon

  Let me give some clarification on a few points:

  2. There is no need to recreate the image on the device using the .img file.  You can improve the mechanism of maintenance of your existing configuration using the .pkg file.  It is the recommended method for upgrading to Cisco IPS devices/modules.  The .img file to recreate the image should only be used to restore the default device.

  5 here are links for the upgrade of the probe using a .pkg file.  For updates through the IDM user interface:

  http://www.Cisco.com/en/us/docs/security/IPS/6.2/configuration/guide/IDM/idm_sensor_management.html#wp2126670

  For upgrades via the CLI:

  http://www.Cisco.com/en/us/docs/security/IPS/6.2/configuration/guide/CLI/cli_system_images.html#wp1142504

  Another point of clarification; current releases of IPS software supported on the AIP-SSM-10 are (taking into account you are currently running 6.2 (1) E3):

  6.2 (3) E4

  7.0 (4) E4

  You can go directly to each output.

  Scott

• ASA Rommon boot guard!

  Hello

  I recently had to re - format, add a new activation key and add the asdm504.bin and the asa704 - k8.bin in my ASA 5520 (I accidentally erased memory on the machine). Now, whenever I use the command "reload" it just directly load in Rommon #... when I get to the Rommon prompt # all what I have to do is type currently... 'start-up' and it loads my file asa704 - k8.bin and load to the top of my config and good mine. I just wonder, is it possible that I would be able to put it easily so it loads the image automatically?

  asa2 (config) #show boot

  Variable BOOT = disk0: / asa704 - k8.bin

  Current BOOT variable = disk0: / asa704 - k8.bin

  Variable CONFIG_FILE = disk0: / startup-config

  Current CONFIG_FILE variable = disk0: / startup-config

  asa2 (config) # disk0 see the:

  The boot disk0: caching, please wait... Fact.

  -# - length - time - path

  8 2995 June 7, 2006 06:30:02 startup-config

  9 5437440 June 7, 2006 06:18:04 asa704 - k8.bin

  10 5958324 June 7, 2006 06:24:08 asdm504.bin

  51515392 bytes available (11431936 bytes used)

  Thank you

  Chris

  Hi Chris,

  0 x 00112002-> which means start the TFTP server, runs aground, go to rommon.

  The ' config-register 0 x 1 ' is ok, that it will ask the ASA to load from default image.»

  As precaution (ditto for me), pls save the config (evem but will not delete the config file).

  Rgds,

  AK

• Site to site VPN - impossible to reach the other side ASA

  Hello

  Recently, I replaced a Juniper with a Cisco ASA 5505 firewall in a branch. This branch has a VPN site to another seat. Firewall at Headquarters is a Juniper and managed by third parties. I have configured the ASA and replaced Juniper. Everything at the Branch works, and can reach all subnets and servers. As the user is concerned, there is no problem.

  But corporate headquarters, I am unable to reach this ASA on the interface of data or management. See the image, I am unable to ping or join a network 192.168.10.0 and 192.168.200.0 or any other subnet 10.15.8.0 to Headquarters. However, I can ping computers from branch office which is in the same subnet as the data interface.

  You guys could help me as I need to reach the ASA headquarters branch. I welcome all networks on both sides inside and the external interface. I also created a NAT as below. Am I wrong configured NAT

  NAT (inside, outside) static source DM_INLINE_NETWORK_4 DM_INLINE_NETWORK_4 HO_Subnets HO_Subnets non-proxy-arp-search of route static destination
  !
  NAT Dynamics obj_any interface of source to auto after (indoor, outdoor)

  DIWA

  This information is useful. You try to SSH to the address inside or management? May I suggest that we focus for now on access to inside? After we get this working, we can watch access via the management.

  It does not appear in what you posted, but I'm not sure if it might be something that you have removed before posting. Do you have configured access to the administration? If this is not the case, may I suggest that you add access management inside the config.

  HTH

  Rick