Implementation gets stuck to the 'HP invent' blue Boot Screen

I have a HP Pavilion a6332f desktop PC.

In Windows, I changed the drive letter of the DVD drive to 'F' to 'Z', and now when I reboot the PC, it gets loaded is stuck on the blue screen 'HP invent '.  This display has the instructions to enter the "Boot Menu", "Setup" and "System Recovery" by pressing key "F11" aor "Esc", "F10".  It is just there for ever.

If I try to enter the 'Boot' Menu by pressing the 'Esc' key, I get the message "Loading Boot Menu... ", but then it hangs there forever just.  If I try to enter the "Setup" Menu, I get a similar result - it says 'enter the Setup... ". "and just hangs there.  By pressing the "F11" key does not seem to do anything.

Any ideas on how to solve this problem?

Thank you

Dan

Spawn1155 wrote: I have a similar problem, have a HP pavillion a1101n starts fine, but after running for a while, if for some reason I have stopped (not restart) the pc, it will freeze on the screen hp for about 10 minutes and then turns off on its own. If I wait about an hour and a half, it will start fine. Restart does not have to do this, it happens only when the pc is turned off and you try to turn back before an hour and a half.

Hello Spawn1155, the problem you describe seems to be more than a heat issue than anything else.

I checked the specs of your system, which can be found here , and it shows that the system was published in May 2005.

This indicates that it is a little old system and could very well have a good amount of dust/dirt accumulation in the case.

I unplug the power cord, remove the side panel and clean the dust/dirt from the inside of the case, paying particular attention to all heatsinh/CPU fan. You can acquire some canned compressed air to clean the radiator/fan to the processor set.

After cleaning the system, try it for a while and see if that solved the problem. If she did not, you may need to restore the software on the system, due to possible corruption. While I do not think that the syytem has a problem of software corruption, she is always better with a new installation of the software after several years of use, if this has not already been done.

Tags: HP Desktops

Similar Questions

  • HP w1907: implementation gets stuck to the 'HP invent' blue Boot Screen

    Hi all

    I have HP w1907 desktop... I use it since 2008.
    Last month I format to have the new windows 7 in it... Previously I was also working with win7 Ultimate.

    But it's keep restarting after the use of 4-5 minutes and so I installed the entire operating system yet.

    It worked very well... after 3-4 weeks, when I started it, it gets stuck at the 'HP invent' blue Boot Screen.

    This display has the instructions to enter the "Boot Menu", "Setup" and "System Recovery" by pressing key "F11" aor "Esc", "F10".  It is just there for ever.

    If I try to enter the 'Boot' Menu by pressing the 'Esc' key, I get the message "Loading Boot Menu... ", but then it hangs there forever just.  If I try to enter the "Setup" Menu, I get a similar result - it says 'enter the Setup... ". "and just hangs there.  By pressing the "F11" key does not seem to do anything.

    Any ideas on how to solve this problem?

    Searching the forums I tried to reset the BIOS - who I've got from here:

    http://h30434.www3.HP.com/T5/desktop-lockups-freezes-hangs/powering-up-gets-stuck-at-Blue-quot-HP-in...

    and

    http://support.HP.com/us-en/document/c01080282

    After doing this too, the result is null

    Please help me...

    I'm in a hurry...

    Thank you.

    Date and the incorrect time can certainly cause problems.  What happens usually, however, is that the sites Web will not be opened because the State in which the certificate is not up-to-date.  I have not heard of the time and date causing the computer does not start.  I think that you need to change the CMOS battery.  Here's a guide on how to change it.  The guide has also some good troubleshooting information.

    Once the battery has been replaced, we'll see what happens.

  • When I turn on my computer, it gets stuck on the ultra-portable gigabyte 3 screen and custom which leave me there 2 hours still no luck the only button that works are TAB rebooting too

    Original title: stuck

    When I turn on my computer, it gets stuck on ultra-portable gigabyte 3 screen and custom wide movement which I gave 2 hours still no luck the only button that works are TAB restart too it can someone help please

    Follow these steps:

    Step 1: Start the computer in safe mode and check if the problem persists.

    A description of the options to start in Windows XP Mode

    http://support.Microsoft.com/kb/315222

    Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

    How to configure Windows XP to start in a "clean boot" State

    http://support.Microsoft.com/kb/310353

    Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

    After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

    (a) click Start, run.

    (b) type msconfigand click OK.

    (c) the System Configuration Utility dialog box appears.

    (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

    (e) when you are prompted, click on restart to restart the computer.

  • Laptop stops randomly and gets stuck on the saving settings

    Basically, we have some laptops 10 + this will stop randomly and get stuck on the "saving settings screens.

    Here are the different models of toshiba R500-R600 M10 M9 M5

    We changed versions of bios etc, reimagee them, even used an image of windows xp disc rather than soe.

    Hardware tests OK and customers do not something in particular, some when others when you connect using applications office, back in after a while. Some use docking stations, others not.

    All ideas

    Hello

    Just a question: are you an authorized service provider?
    I ask this question because it looks like you are an ASP because you have so many laptops and you have tested different things.

    It's really hard to say what the reason is for this but I think that in this case, you should contact Toshiba directly. Maybe it s a known issue and it can be fixed in a few minutes.
    So ask for it and wait for a response.

  • Sometimes, the Lenovo Y40 gets stuck on the Lenovo screen?

    The Y40 I bought in July sometimes gets stuck on the Lenovo screen where the laoding circle does not appear. It happens only intermittently, but occurs more often after long use (more than 45 minutes). Technical support already tells me to reset the BIOS and restore windows. Do you know the guys from any thing that can cause this problem? Would it be a HARD drive broken or damaged OS? Thank you!

    I've already sent my laptop in for repair. The technical support representative said that it was either a HARD drive or motherboard problem

  • I have a Macbook pro (2011 model). It gets stuck on the start screen on to half way through commissioning. This happens whenever the mac turns on. The problem is solved when I reinstall Yosemite to boot to Recovery Mode disk utility.

    I have a Macbook pro (2011 model). It gets stuck on the start screen on to half way through commissioning. This happens whenever the mac turns on. The problem is solved when I reinstall Yosemite to boot to Recovery Mode disk utility. However, the next time you start, the startup process is blocked to halfway to new (on the screen with the toolbar and the status of apple). I want a more permanent solution to reinstall the operating system every time. Would appreciate someone's suggestions and thanks in advance.

    Replace your hard drive.

    You have a backup of trust? If not, buy a disc of exterrnal for that as well.

    The progress bar from the left end at the beginning of the commissioning indicates that your drive has been so damaged, it could not be mounted. Five minutes of progress bar is shown as it does the equivalent of disk utility (ERD [Directory]). If you have reinstalled several times and the problem is not fixed, your drive is in solid form.

  • Servo motor gets stuck in the loop

    My project is to control two motors from the pedals with LabVIEW in combination with UMI-7774 and PCI 7350.

    I use a traditional format of State Machine to simultaneously control two motors according to the absolute position mode.

    In one of the first States, both motors are wound manually by using the speed mode (to make a desired voltage).

    In a later State, the motors are wound to a position specified by the user when you press a foot switch. When you press the other pedal, they are then held in the previous "original" position

    After the first "Tension" indicate when the winding engine and the course due to the pedals is running, the program gets stuck in the State of wind.

    Although drivers are told to go to a specific position, they never move and that's why the program is unable to move to the next State.

    I've attached a screenshot of the winding State where the program is stuck (the engines are not mobile, so when the final position is to compare it with the desired position, the loop continues to go).

    Help, please.

    CAT

    I solved the problem.

    States "Wind engine left" and "Right wind engine" speed has been put back to zero. When the program moves toward States of wind/flow, the speed is always zero (the engines cannot move).

    I simply set the speed value desired in each of the States LBL/RBL (that allowed the engine to get to the position of desire).

    Thanks for all the help,

    Catherine

  • Everything I print gets stuck in the queue, but the document is printed

    ORIGINAL TITLE: Spooler

    I installed a printer on a pc windows 7 64. Everything I print gets stuck in the queue, but the document is printed. The printer is on the network, I tried to restart the spooler and erased the record of the spooler, but perisisted of the question, given that the document gets stuck, no other agency will be able to print, remove the paper and print again to print but the file gets stuck again on the queue. I tried to change the IP address, but the same thing happened. Can someone help me?

    Hi, Omorguz,

    Printer brand and model, if you please.

    Start > run > type services.msc

    Press enter

    Scroll down to print spooler

    Select stop

    Let Windows stop the spooler

    Control Panel > printers and Faxes folder

    Right-click on the printer icon, then select open

    If you see pending orders in the queue, select the

    Click file > cancel all Documents

    If a job shows the deletion, but never finished, open the command prompt window

    Start > run > type cmd

    Press Ok

    Enter Net Stop Spooler

    Press enter

    Wait for the DOS window opens and is

    Open the command prompt window

    Type Net Start Spooler

    Press enter

    If that does not cancel the print job:

    Your directory of spools Windows XP is located at

    C:\WINDOWS\SYSTEM32\SPOOL\PRINTERS

    It will usually contain files like these:

    FP00008
    FP00008. SHD

    There are two files for each remaining print job.  Just delete these and restart the computer.  Your queue should now be provisioned.

    If you are printing over a network, and the queue is not clear after the above steps:

    Go to the computer that has the shared printer connected and perform steps 1 & 2 above.

    If this does not work, then go to the computer when he was sent to the printing of the task and perform the steps 1 & 2 on this computer.

    Run chkdsk

    Start > run > type CMD

    Press Ok

    Type C: chkdsk/r/f

    Press enter

    You will receive a message re: volume must be locked and you want to start scanning reboot?  Press y and press enter

    Type Exit to close the CMD window

    Restart the computer for the scan at startup

    This will check the integrity of your data on the hard drive of computer as well as find and fix errors that could corrupt your data or program files.

    I even recommend that you uninstall the printer and when you are done uninstalling, restart computer.

    When you reinstall the printer, reinstall it using the compatibility mode

    How to install a hardware device using the compatibility mode driver.

    http://social.technet.Microsoft.com/forums/en-us/w7itprohardware/thread/80cae5ee-dc98-4A2F-8284-a1ab826059b7

    It works on Windows 7 Professional, comprehensive and business - Windows XP Mode - it's free

    It's the best of both worlds: the new Windows XP Mode allows you to run Windows XP older right on your Windows 7 desktop business software.

    http://Windows.Microsoft.com/en-us/Windows7/products/features/Windows-XP-mode

    e FAQ or choose a link from the top of this page.
     
  • When I send a message it gets stuck in the Outbox and won't unless I click on the message until it is "BOLD" with a print, then delete.

    Forwarded messages or new messages are not automatically leave and get stuck in the Outbox.  If I leave it alone, I get a message that there was an error and the message could not be sent.  However, if I leave the message stuck in the Outbox, the message gets actually released several times until I have go into the Outbox and delete the message.

    Compacting files try one at a time.

    To defragment:

    Start | All programs | Accessories | System Tools | Disk Defragmenter. Just above that you'll also see disk cleanup. I was running first and also in the other Options tab, the third option to get rid of old that take place of restore points.

    Bruce Hagen
    MS - MVP October 1, 2004 ~ September 30, 2010
    Imperial Beach, CA

  • Documents get stuck in the printer queue and I have to restart so that they print

    often, when I try to print a document or web page, or anything, the document will get stuck in the queue for the printer.  the printer will tell me 1 post pending but nothing prints.  I have to restart my computer to print the document.

    No answers so I'll try to help. I don't have a printer for many years. A practical tool, I used to use repeatedly put my printer icon on my desktop or in the taskbar. Try it! Go to Control Panel, open Printers and faxes, right click on your printer and choose Create shortcut and click Yes. Once on your desktop then drag it to the taskbar when you have a page open it will be more accessible. Open it and click on the printer and click Cancel all documents. From what I remember when the print queue of the printer is over load it won't print and clicking on cancel all documents throws to the queue. Check the menu options to set your preferences. I hope this helps!

  • Question from windows vista - get stuck on the Welcome screen.

    I recently had my computer startup problems - it gets stuck on the home page, even if I restart it continues.  If I'm doing a ctrl + alt + delete, and then it displays the desktop.  I have no updates that must be accomplished.  you have an idea why this is stuck?  Thank you!

    Restore point:

    Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

    Try a restore of the system once, to choose a Restore Point prior to your problem...

    Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

     

    If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

    Download the ISO on the link provided and make a record of repair time it starts.

    Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

    At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

    When you have changed that, insert the Bootable disk you did in the drive and reboot.

    http://www.bleepingcomputer.com/tutorials/tutorial148.html

    Link above shows what the process looks like and a manual, it load the repair options.

    NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

    Read all the info on the website on how to create and use it.

    http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

    ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

    It's a very good Vista startup repair disk.

    You can do a system restart tool, system, etc it restore.

    It is NOT a disc of resettlement.

    And the 32-bit is what normally comes on a computer, unless 64-bit.

    See you soon.

    Mick Murphy - Microsoft partner

  • I train for adobe flash, but it gets stuck in the Middle download saying "close idvault. Cannot find where to close the application.

    I train for adobe flash, but it gets stuck in the Middle download saying "close idvault. Cannot find where to close the application.

    Click Start, type: Internet Options

    Press enter

    Select the "Advanced" tab

    Under reset Internet Explorer settings, click "reset".

    This should restore the Internet Explorer default settings.

    Then reinstall Flash Player

    http://get.Adobe.com/flashplayer/

    ----------

    Flash Player

    Troubleshoot installation of Flash Player for Windows

    http://kb2.Adobe.com/CPS/191/tn_19166.html

    Troubleshooting player stability and performance

    http://blogs.Adobe.com/JD/2010/02/troubleshooting_player_stabili.html

    Uninstaller

    http://kb2.Adobe.com/CPS/141/tn_14157.html

    Flash Player Support Forum

    http://forums.Adobe.com/community/webplayers/flash_player

  • HP G6 Windows 8.1 sometimes stuck on the start up repair/diagnostic screen

    I have a Pavilion G6 accompanying win 8 and I've updated to 8.1.   Normally, works very well.  But sometimes if it is not stop properly, or after updates, it gets stuck in the rotating balls forever.   Usually after 3 stops forced, I get repair folollowed preparation of the diagnose sceens pc, and then it works when I select restart.    A few times I had to go through the process several times, but so far, it has always started.

    Any suggestions?

    Thank you.

    Some things you could try for now.

    Make a diagnosis via hard drive BIOS

    Restore the default settings of the BIOS

    http://support.HP.com/us-en/document/c02693833

    Run the Memtest86 to test your RAM from there, not the paid version:

    http://www.Memtest86.com/

    Consider changing your CMOS battery.

  • How can I get rid of the second bar blue at the top of my browser window after I open a new window?

    When I open a new window or click a link that opens a new window, the new window has two blue bars along the top of the screen. The top bar is the one that I expect to see with the firefox logo, the name of the Web looking at page and the reduce, enlarge, close buttons. The second bar, below, has a tab orange on the left side who says "Firefox" with an arrow pointing downwards and then on the right side has him minimize, maximize and close buttons. These buttons are the same buttons on the blue bar to the top do. Below the second blue bar is the normal toolbar, but the upstream and downstream buttons do not work. How can I get rid of the second blue bar. He began to appear after the last update I did last week.

    This always happens if you launch Firefox with extensions disabled?

    This page is a report of another user with the same problem, which says that the problem has disappeared after disable the extensions.

  • Keys get stuck on the Satellite A60 - 142

    Hello all, I hope someone can help me here.
    Currently I; m using my laptop frequently, I write a thesis.
    I have problems with my keyboard: some keys stuck after working for a while, it is never from the beginning. The keys that get stuck caps lock, shift, and CTRL keys, very irritating when you type a text. Restart is not enough, when I do that some letter keys do not work. The laptop must be turned on during some time to make it work properly again. Anyone have experience with this problem and knows how to solve?

    Thanks, has soon B.T., Amsterdam, Holland

    Hello

    What do you mean exactly? The essential mechanism or the key issue of software?
    If you mean the key mechanism then I recommend to remove the CAP from the keyboard and then you can try to clean the key spot. Perhaps a dirt and grime could have a negative influence on the use of the key.

    But if it is a software problem if the cleaning process will not help.
    Sometimes cable keyboard could have a bad influence on the function of the keyboard.
    Have you tried to reinstall the OS? I think you should check if the new installation of the OS could solve this problem.

Maybe you are looking for