Implementation of the remote access VPN IPSec using SRI 2801
Hello
I tried to set up a VPN for remote access using 2801 SRI. I've been able to establish my house vpn tunnel using the DSL (behind a NAT) connection, give it SRI the IP address that is in the ip pool I configured on safety. The problem I have right now is that it does not reach the company LAN network.
DIAGRAM:
MODEM PC (VPN CLIENT) ADSL - ROUTER SOHO - INTERNET - ISR2801 - LAN---(10.10.0.27&192.168.0.9) COMPANY
PC: 172.16.10.122
SOHO ROUTER LAN IP: 172.16.10.254
SOHO ROUTER WAN IP: Dynamically assigned by ISP
ISR2801 WAN IP: x.x.x.5/224
IP LAN ISR2801: 10.10.0.50/24
The CORPORATE LAN subnet: 10.10.0.0/24 and 192.168.0.9/24
2801 SRI CONFIGURATION:
AAA new-model
!
!
connection of AAA NOCAUTHEN group local RADIUS authentication
local NOCAUTHOR AAA authorization network
!
!
IP domain name xxxxx.com
!
!
!
username root password 7 120B551806095F01386A
!
!
crypto ISAKMP policy 3
BA 3des
preshared authentication
Group 2
ISAKMP crypto 5 40 keepalive
ISAKMP crypto nat keepalive 20
!
Configuration group isakmp crypto-GROUP NOC client
touch [email protected]/ * /! ~ $ 9876 qwerty
DNS 192.168.0.9
192.168.0.9 victories
xxxxx.com field
LWOP-pool
include-local-lan
netmask 255.255.255.0
!
!
Crypto ipsec transform-set AC - SET esp-3des esp-sha-hmac
!
dynamic-map crypto NOC-DYNAMICMAP 10
transformation-LWOP-SET game
!
!
list of crypto AC-customer card NOCAUTHEN card authentication
list of crypto isakmp NOCAUTHOR AC-card card authorization
crypto map CNP-map client configuration address respond
Crypto map AC - map 10-isakmp dynamic ipsec AC-DYNAMICMAP
!
!
!
!
interface FastEthernet0/0
IP address x.x.x.5 255.255.255.224
Speed 100
full-duplex
card crypto AC-map
!
interface FastEthernet0/1
IP 10.10.0.50 255.255.255.0
Speed 100
full-duplex
!
local IP NOC-POOL 192.168.250.101 pool 192.168.250.110
IP route 0.0.0.0 0.0.0.0 XXX1
IP route 10.10.0.0 255.255.255.0 10.10.0.10
IP route 172.16.10.0 255.255.255.0 FastEthernet0/0
Route IP 192.168.0.0 255.255.255.0 10.10.0.10
IP route 192.168.250.0 255.255.255.0 FastEthernet0/0
!
I have attached a few screenshots. My goal here is to have access to my LAN to the company (10.10.0.0/24 and 192.168.0.9/24). I don't know what is missing here.
No, we don't need not NAT. wanted to confirm if NAT could cause this problem.
The config looks good. Can you ping routers ip internal interface the client LAN once it connects?
Are correct, w.r.t. transatlantic lines reaching pool behind router VPN?
If so, I would like to take a look at the exits following when a client is connected.
See the crypto eli
ISAKMP crypto to show his
Crypto ipsec to show his
SPSP
Tags: Cisco Security
Similar Questions
-
Configuration remote access VPN (IPSec) using FULL domain name
Hi friends of Cisco,
We have the DNS (only the internal IP) within our network, right now that we have configured VPN for remote access using public IP address and connect us with the same public IP address. I need help to use the domain name FULL rather than use public IP.
Can you please provide the configuration for this.
Feature: ASA 5520
Type of configuration: IPSec
Thank you
Estel
Hi Philippe,.
You can use one of the free Web of DNS dynamic sites and configure ASA to dynamic DNS.
Reference - http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/basic_ddns.html
HTH,
-Dieng
-
Unable to SSH/telnet through the remote access VPN to ASA interface
Hi all - im trying to SSH/telnet to my ASA in my remote access VPN tunnel but
can't get this to work. what Miss me?
remote access VPN subnet: 192.168.25.0
LAN subnet: 192.168.1.0
config is attached. THX-
Please enter the command
Private access Managament
and you will be able to telnet/ssh to the asa on this ip 192.168.1.253
-
Through remote access vpn Ipsec within the host is not available.
Team,
I have a question in confiuration vpn crossed.
ASA 3,0000 Version 5
the only question is, to access remote vpn clinet IP cannot access inside the host. However able to reach the branch of IP and it uses corprate Internet.
In SAA from the external interface I am able to ping remote clint IP but not from within the interface. Please help and let me know if additional information is required.
Thank you
Knockaert
Hello
For the NAT0 configuration, you only need NAT0 instruction for the interface "inside".
This single command/ACL should allow for 'inside' <-->'vpn-pool' communication.
NAT0 configurations on the 'external' interface should be necessary only if you make NAT0 between 2 VPN connections. I guess you could do this since you mention traffic crossed?
I suggest using different 'object-group' to define networks of NAT0 destination for different ' object-group' to the 'outside' to 'outside' and 'inside' users NAT0.
I also obsessively using beaches too wide network in the statements of NAT0. According to some records, they can cause problems
For example, this network ' object-network 172.16.0.0 255.240.0.0 "contains the 172.x.x.x.x set private IP address range. And in this case it contains some of your 'inside' networks too?
How is this a problem of crossed by the way? You say that the problem is between the VPN clients on the 'external' interface and network local hosts behind the 'internal '? Crossed would mean you have connection problem between 'outside' <->'outside' perhaps.
I don't know if I made any sense. Can be a bit messy. But can not give very specific answers that I don't know the entire configuration.
Also make sure you have the "inspect icmp" configured under the policy-map of the world, so that the response to ICMP echo messages are automatically allowed through the ASA.
-Jouni
->--> -
Client connected to the remote access VPN, but got the wrong default gateway
Hi all
I struggled for a few days and really need some help here. My PC (192.168.254.x) is on the same vlan with external interface (192.168.254.171) to my PIX506E. When I run the Cisco VPN client, my PC shows connected and gets the IP address of 10.9.0.150 that is expected. However, it also gets the entry door of 10.9.0.1 that I have no idea where it came from. So my PC can not access any external or internal network.
I've listed below the configuration of my and highlighted the part that I typed in. PIX version 7.1 (2) is the latest version that I can install on PIX506E. Help, please. Thank you very much.
pixfirewall # sh run
: Saved
:
PIX Version 7.1 (2)
!
pixfirewall hostname
activate 2KFQnbNIdI.2KYOU encrypted password
names of
!
interface Ethernet0
nameif outside
security-level 0
IP 192.168.254.171 255.255.255.0
!
interface Ethernet1
nameif inside
security-level 100
IP 10.10.10.1 255.255.255.0
!
2KFQnbNIdI.2KYOU encrypted passwd
Flash: / pix712.bin starting system
passive FTP mode
pager lines 24
Enable logging
timestamp of the record
logging buffered information
Outside 1500 MTU
Within 1500 MTU
10.9.0.150 mask - local 10.9.0.160 ROBERT-pool IP 255.255.255.0
don't allow no asdm history
ARP timeout 14400
Route outside 0.0.0.0 0.0.0.0 192.168.254.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00
Timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
internal group strategy Robert-GP
attributes of Group Policy GP-Robert
value of server DNS 8.8.8.8
username cisco password encrypted privilege 15 3USUcOPFUiMCO4Jk
robert yXUoa8oHzS0Ncp2O of encrypted password username
robert username attributes
Strategy Group-VPN-Robert-GP
the ssh LOCAL console AAA authentication
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Dynamic crypto map DYN1 1 set of transformation-RIGHT
Dynamic crypto map DYN1 1jeu reverse-road
map MYMAP 1 ipsec-isakmp dynamic DYN1 crypto
MYMAP outside crypto map interface
ISAKMP allows outside
part of pre authentication ISAKMP policy 1
ISAKMP policy 1 3des encryption
ISAKMP policy 1 sha hash
Group of ISAKMP policy 1 2
ISAKMP policy 1 life 43200
ISAKMP nat-traversal 30
tunnel-GROUP ROBERT type ipsec-ra
tunnel-group ROBERT-General-attributes
address-pool ROBERT-
Group Policy - by default-Robert-GP
tunnel-group ROBERT-GROUP ipsec-attributes
pre-shared-key *.
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 60
SSH version 2
Console timeout 0
SSL rc4 - md5 encryption
Cryptochecksum:7157c6095f2abae2aae9e15c1caa81aa
: end
pixfirewall #.disconnect from the vpn session after adding the new ACL to the external interface and try again?
Disconnect the vpn session and try again and if does not apply this line.
permit same-security-traffic intra-interface
See the ipsec crytop her.
Please post this output.
Thank you
-
Remote access VPN with ASA 5510 by using the DHCP server
Hello
Can someone please share your knowledge to help me find out why I'm not able to receive an IP address on the remote access VPN connection so that I can get an IP local pool DHCP?
I'm trying to set up remote access VPN with ASA 5510. It works with dhcp local pool but does not seem to work when I tried to use an existing DHCP server. It is tested in an internal network as follows:
!
ASA Version 8.2 (5)
!
interface Ethernet0/1
nameif inside
security-level 100
IP 10.6.0.12 255.255.254.0
!
IP local pool testpool 10.6.240.150 - 10.6.240.159 a mask of 255.255.248.0. (worked with it)
!
Route inside 0.0.0.0 0.0.0.0 10.6.0.1 1
!
Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dyn1 1jeu transform-set FirstSet
dynamic mymap 1 dyn1 ipsec-isakmp crypto map
mymap map crypto inside interface
crypto ISAKMP allow inside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
!
VPN-addr-assign aaa
VPN-addr-assign dhcp
!
internal group testgroup strategy
testgroup group policy attributes
DHCP-network-scope 10.6.192.1
enable IPSec-udp
IPSec-udp-port 10000
!
username testlay password * encrypted
!
tunnel-group testgroup type remote access
tunnel-group testgroup General attributes
strategy-group-by default testgroup
DHCP-server 10.6.20.3
testgroup group tunnel ipsec-attributes
pre-shared key *.
!
I got following output when I test connect to the ASA with Cisco VPN client 5.0
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: (4) SA (1) + KE + NUNCIO (10) + ID (5), HDR + VENDO
4024 bytesR copied in 3,41 0 seconds (1341 by(tes/sec) 13) of the SELLER (13) seller (13) + the SELLER (13), as well as the SELLER (13) ++ (0) NONE total length: 853
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ISA_KE
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, nonce payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received xauth V6 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, DPD received VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received Fragmentation VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received NAT-Traversal worm 02 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, connection landed on tunnel_group testgroup
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA proposal # 1, turn # 9 entry overall IKE acceptable matches # 1
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build the payloads of ISAKMP security
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building nonce payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for answering machine...
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of payload ID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of Cisco Unity VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing payload V6 VID xauth
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building dpd vid payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing the payload of the NAT-Traversal VID ver 02
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of Fragmentation VID + load useful functionality
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, send Altiga/Cisco VPN3000/Cisco ASA GW VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR SA (1) KE (4) NUNCIO (10) + ID (5) + HASH (8) + SELLER (13) + the SELLER (13) + the SELLER (13) + the SELLER (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) total length: 440
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + HASH (8) + NOTIFY (11) + NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) overall length: 168
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, useful treatment IOS/PIX Vendor ID (version: 1.0.0 capabilities: 00000408)
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: Group = testgroup, I
[OK]
KenS-mgmt-012 # P = 10.15.200.108, status of automatic NAT detection: remote end is NOT behind a NAT device this end is NOT behind a NAT device
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 72
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 87
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, transformation MODE_CFG response attributes.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized primary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized secondary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Compression IP = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling political = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: setting Proxy browser = no - modify
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: browser Local Proxy bypass = disable
Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, (testlay) the authenticated user.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 64
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + NONE (0) overall length: 60
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cfg ACK processing attributes
Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 49ae1bb8) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 182
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, treatment cfg request attributes
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 address!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 network mask!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for DNS server address.
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the address of the WINS server.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, transaction mode attribute unhandled received: 5
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the banner!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting save PW!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: receipt of request for default domain name!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for Split-Tunnel list!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for split DNS!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for PFS setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Proxy Client browser setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the list of backup peer ip - sec!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting disconnect from the Client Smartcard Removal!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Version of the Application.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Type of Client: Windows NT Client Application Version: 5.0.07.0440
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for FWTYPE!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: request received for the DHCP for DDNS hostname is: DEC20128!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the UDP Port!
Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = b04e830f) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE has received the response from type [] at the request of the utility of IP address
Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cannot get an IP address for the remote peer
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE TM V6 WSF (struct & 0xd8030048)
, : TM_DONE, EV_ERROR--> TM_BLD_REPLY, EV_IP_FAIL--> TM_BLD_REPLY NullEvent--> TM_BLD_REPLY, EV_GET_IP--> TM_BLD_REPLY, EV_NEED_IP--> TM_WAIT_REQ, EV_PROC_MSG--> TM_WAIT_REQ, EV_HASH_OK--> TM_WAIT_REQ, NullEvent Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE AM Responder WSF (struct & 0xd82b6740)
, : AM_DONE, EV_ERROR--> AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL--> AM_TM_INIT_MODECFG_V6H NullEvent--> AM_TM_INIT_MODECFG, EV_WAIT--> AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG--> AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK--> AM_TM_INIT_XAUTH_V6H NullEvent--> AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b ending: 0x0945c001, refcnt flags 0, tuncnt 0
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending clear/delete with the message of reason
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing the payload to delete IKE
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 9de30522) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80
Kind regards
Lay
For the RADIUS, you need a definition of server-aaa:
Protocol AAA - NPS RADIUS server RADIUS
AAA-server RADIUS NPS (inside) host 10.10.18.12
key *.
authentication port 1812
accounting-port 1813
and tell your tunnel-group for this server:
General-attributes of VPN Tunnel-group
Group-NPS LOCAL RADIUS authentication server
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
We have 10 sites with ASA 5505 connected to the ASA 5510 of main office
through IPSec VPN tunnels. Home users connect to the main office network
using the remote access vpn connection. They can also connect to the ASA 5505
remote sites by vpn for remote access to the ASA 5510?
Thanks, please help!
Here's the PDF.
-
Redundancy ASA - Client to the remote access (AnyConnect or IPsec) VPN Cisco to 2 PSI
Hello
I realize that the true public access redundancy require routers and BGP need &AS#; but some can't afford such a solution. Should someone have ASA 5510 dry + with 2 of the ISP could use IP SLA functionality for primary education to save the failover, etc.. What VPN clients for remote access (SSL or IPSec). I'm curious if you have any other solutions/configurations on it to allow either of these customers, AnyConnect or IPsec, to try the primary counterpart and after a few failed attempts over fail to backup (even if a user tries to establish a VPN)? I know that one of the possible solutions may use a domain name FULL peer IPSec or AnyConnect client input, then maybe public operator DNS TTL change or other hosted / failover services... but these "proxy" or DNS services are not the best solution because there is cache and other associated DNS weaknesses (right)? These are not infallible fail-over, I'm sure that some users might succeed and some may fail; I do not know administrators will be like that as much as they like going to the dentist.
Anyone who has any ideas or possible solutions?
Thank you.
Hello
Backup servers are supported by remote access VPN clients.
The client will attempt to connect to the first IP/configured FULL domain name and will try the following in the list, if no response is received.
Federico.
-
How to prohibit remote access vpn client to use the local DNS server
Hello
I'm on ASA5505 remote access vpn configuration.
Everything works fine so far, except when the client got connected, he always used the local DNS server provided by the ISP. How can I force the customer to use the DNS server configured on ASA?
Thank you.
Kind regards
The command "Activate dns split-tunnel-all" is supported only on SSL VPN and VPN IKEv2. Since you're using IKEv1, this command is not supported.
Here's the order reference:
http://www.Cisco.com/en/us/docs/security/ASA/asa82/command/reference/S8.html#wp1533793
You configure no split tunnel? If you are, then you need to configure "tunnelall" split tunnel policy, and that will force the dns resolution and everything else through the VPN tunnel.
-
Hello
I'm trying to solve a problem with the VPN, and I hope that someone could give me a helping hand.
We have 3 offices, each with an ASA 5505 like the router/firewall, connected to a cable modem
(NC Office) <----IPSEC----->(office of PA) <----IPSEC----->(TC Office)
Internally, we have a full mesh VPN, so all offices can talk to each other directly.
I have people at home, by using remote access VPN into the Office of PA, and I need them to be able to connect to two other offices there.
I was able to run for the Office of CT, but I can't seem to work for the Office of the NC. (I want to say is, users can remote access VPN in the PA Office and access resources in the offices of the PA and CT, but they can't get the Office of NC).
Someone could take a look at these 2 configs and let me know if I'm missing something? I am newer to this, so some of these configs do not have better naming conventions, but I'm getting there
PA OFFICE
Output of the command: "show run".
: Saved
:
ASA Version 8.2 (5)
!
hostname WayneASAnames of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 70.91.18.205 255.255.255.252
!
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS lookup field inside
DNS domain-lookup outside
DNS server-group DefaultDNS
75.75.75.75 server name
75.75.76.76 server name
domain 3gtms.com
permit same-security-traffic intra-interface
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
inside_access_in of access allowed any ip an extended list
IPSec_Access to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.2.0 255.255.255.0
IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0
inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.224
inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
TunnelSplit1 list standard access allowed 192.168.10.0 255.255.255.224
TunnelSplit1 list standard access allowed 192.168.1.0 255.255.255.0
outside_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
outside_2_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
outside_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
RemoteTunnel_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.1.0 255.255.255.0
RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.2.0 255.255.255.0
RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.5.0 255.255.255.0
out_access_in list extended access udp allowed any SIP host 70.91.18.205 EQ
out_access_in list extended access permit tcp any host 70.91.18.205 eq 5000
out_access_in list extended access permits any udp host 70.91.18.205 range 9000-9049
out_access_in list extended access permit tcp any host 70.91.18.205 EQ SIP
out_access_in list extended access allowed object-group TCPUDP any host 70.91.18.205 eq 5090
out_access_in list extended access permit udp any host 70.91.18.205 eq 5000
Note to outside-nat0 access-list NAT0 for VPNPool to Remote Sites
outside-nat0 extended ip 192.168.10.0 access list allow 255.255.255.224 192.168.2.0 255.255.255.0
outside-nat0 extended ip 192.168.10.0 access list allow 255.255.255.224 192.168.5.0 255.255.255.0
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU----IPSEC----->----IPSEC----->
IP mask 255.255.255.224 local pool VPNPool 192.168.10.1 - 192.168.10.30
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 0-list of access outside-nat0
inside_access_in access to the interface inside group
Access-group out_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 70.91.18.206 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set esp-3des esp-md5-hmac VPNTransformSet
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto IPSec_map 1 corresponds to the address IPSec_Access
card crypto IPSec_map 1 set peer 50.199.234.229
card crypto IPSec_map 1 the transform-set VPNTransformSet value
card crypto IPSec_map 2 corresponds to the address outside_2_cryptomap
card crypto IPSec_map 2 set pfs Group1
card crypto IPSec_map 2 set peer 98.101.139.210
card crypto IPSec_map 2 the transform-set VPNTransformSet value
card crypto IPSec_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
IPSec_map interface card crypto outside
card crypto outside_map 1 match address outside_1_cryptomap
peer set card crypto outside_map 1 50.199.234.229
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
Telnet 192.168.1.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 60
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.1.100 - 192.168.1.199 inside
dhcpd dns 75.75.75.75 75.75.76.76 interface inside
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal RemoteTunnel group strategy
attributes of Group Policy RemoteTunnel
value of server DNS 75.75.75.75 75.75.76.76
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list RemoteTunnel_splitTunnelAcl_1
dfavier vUA99P1dT3fvnDZy encrypted password username
username dfavier attributes
type of remote access service
rduske vu0Zdx0n3oZWFSaX encrypted password username
username rduske attributes
type of remote access service
eric 0vcSd5J/TLsFy7nU password user name encrypted privilege 15
lestofts URsSXKLozQMSeCBk username encrypted password
username lestofts attributes
type of remote access service
jpwiggins 3WyoRxmI6LZjGHZE encrypted password username
username jpwiggins attributes
type of remote access service
tomleonard cQXk0RJCBtxyzZ4K encrypted password username
username tomleonard attributes
type of remote access service
algobel 4AjIefFXCbu7.T9v encrypted password username
username algobel attributes
type of remote access service
type tunnel-group RemoteTunnel remote access
attributes global-tunnel-group RemoteTunnel
address pool VPNPool
Group Policy - by default-RemoteTunnel
IPSec-attributes tunnel-group RemoteTunnel
pre-shared key *.
tunnel-group 50.199.234.229 type ipsec-l2l
IPSec-attributes tunnel-group 50.199.234.229
pre-shared key *.
tunnel-group 98.101.139.210 type ipsec-l2l
IPSec-attributes tunnel-group 98.101.139.210
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the pptp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:6d1ffe8d570d467e1ea6fd60e9457ba1
: endCT OFFICE
Output of the command: "show run".
: Saved
:
ASA Version 8.2 (5)
!
hostname RaleighASA
activate the encrypted password of Ml95GJgphVRqpdJ7
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
192.168.5.1 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 98.101.139.210 255.0.0.0
!
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS lookup field inside
DNS server-group DefaultDNS
Server name 24.25.5.60
Server name 24.25.5.61
permit same-security-traffic intra-interface
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
Wayne_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
Wayne_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
Shelton_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.2.0 255.255.255.0
out_access_in list extended access permit tcp any host 98.101.139.210 eq www
out_access_in list extended access permit tcp any host 98.101.139.210 eq ftp
out_access_in list extended access permit udp any host 98.101.139.210 eq tftp
out_access_in list extended access udp allowed any SIP host 98.101.139.210 EQ
out_access_in list extended access permit tcp any host 98.101.139.210 eq 5090
out_access_in list extended access permit tcp any host 98.101.139.210 eq 2001
out_access_in list extended access permit tcp any host 98.101.139.210 eq 5080
out_access_in list extended access permit tcp any host 98.101.139.210 eq ssh
out_access_in list extended access permit tcp any host 98.101.139.210 eq 81
out_access_in list extended access permit tcp any host 98.101.139.210 eq 56774
out_access_in list extended access permit tcp any host 98.101.139.210 eq 5000
out_access_in list extended access permit tcp any host 98.101.139.210 eq 902
out_access_in list extended access permit tcp any host 98.101.139.210 eq netbios-ssn
out_access_in list extended access permit tcp any host 98.101.139.210 eq 445
out_access_in list extended access permit tcp any host 98.101.139.210 eq https
out_access_in list extended access allowed object-group TCPUDP any host 98.101.139.210 eq 3389
out_access_in list extended access allowed object-group TCPUDP range guest 98.101.139.210 5480 5487
out_access_in list extended access permits any udp host 98.101.139.210 range 9000-9050
inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.2.0 255.255.255.0
inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0
NAT (inside) 1 0.0.0.0 0.0.0.0Access-group out_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 98.101.139.209 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac WayneTransform
Crypto ipsec transform-set esp-3des esp-md5-hmac SheltonTransform
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto IPSec_map 1 corresponds to the address Wayne_Access
card crypto IPSec_map 1 set pfs Group1
card crypto IPSec_map 1 set peer 70.91.18.205
card crypto IPSec_map 1 the transform-set WayneTransform value
card crypto IPSec_map 2 corresponds to the address Shelton_Access
card crypto IPSec_map 2 set pfs Group1
card crypto IPSec_map 2 set peer 50.199.234.229
card crypto IPSec_map 2 the transform-set SheltonTransform value
IPSec_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 5
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.5.100 - 192.168.5.199 inside
dhcpd dns 24.25.5.60 24.25.5.61 interface inside
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
eric 0vcSd5J/TLsFy7nU password user name encrypted privilege 15
tunnel-group 50.199.234.229 type ipsec-l2l
IPSec-attributes tunnel-group 50.199.234.229
pre-shared key *.
tunnel-group 70.91.18.205 type ipsec-l2l
IPSec-attributes tunnel-group 70.91.18.205
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:3d770ba9647ffdc22b3637e1e5b9a955
: endHello
I might have found the problem.
To be honest, I'm a little tired and concentration is difficult, especially when access between multiple device configurations. So second pair of eyes is perhaps in order.
At the moment it seems to me that this configuration is the problem on the SITE of PA
IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0
This is an ACL that defines networks the and remote for a connection VPN L2L.
Now, when we look at what connection VPN L2L this belong we see the following
card crypto IPSec_map 1 corresponds to the address IPSec_Access
card crypto IPSec_map 1 set peer 50.199.234.229
card crypto IPSec_map 1 the transform-set VPNTransformSet value
Now, we see that the peer IP address is 50.199.234.229. Is what site this? The IP address of the CT Site that works correctly?
Now what that said the ACL line I mentioned more early basically is that when the 192.168.10.0 network 255.255.255.224 wants to connect to the network 192.168.5.0/24 should be sent to the CT Site. And of course, this should not be the case as we want traffic to go on the NC Site
Also worth noting is that on the SITE of the above connection is configured with the '1' priority so it gets first compared a connection. If the VPN L2L configurations were in different order then the VPN Client connection can actually work. But it's just something that I wanted to point out. The actual resolution of the problem, of course, is to detach the configuration which is the cause of the real problem in which ASA attempts to route traffic to a completely wrong place.
So can you remove this line ACL of the ASA of PA
No IPSec_Access access list extended ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0
Then, test the VPN Client connection NC SITE again.
Hope that this will finally be the solution
-Jouni
-
VPN error 868 the name of the remote access server is not resolved
I use Windows 7 Home Premium and you want to configure a VPN with my office network that uses the Check Point Safe@Office. I am unable to log in and get the error that does not resolve the name of the remote access server and Windows cannot find the host using DNS name. Any suggestions on what to try to fix the problem? I set up the VPN connection according to the instructions of our network administrator. We use XP in the office.
Hello
Welcome to the Microsoft answers siteThe question that you'd be better suited in the TechNet community. Please visit the link below to find a community that will provide the best support.
http://social.technet.Microsoft.com/forums/en-us/ForefrontedgeVPN/threadsIt may be useful
Thanks and greetings
Support Microsoft-dieng
Visit our Microsoft answers feedback Forum and let us know what you think
http://social.answers.Microsoft.com/forums/en-us/answersfeedback/threads/ -
ODA IP ASA when you browse the web via remote access vpn
Hi all
I was wondering if it is possible to configure an ASA5510 in a way to allow users remote access VPN use external IP of the ASA when browsing the web. So what I'm looking for is a solution to hide my IP address and use the IP address of the ASA, when browsing.
The firmware version of the ASA is 9.1 (6)
Thanks in advance
Hello
What you want to achieve is calles u-turn.
You must enable the feature allowed same-security-traffic intra-interface
For the configuration of the asa, here's the Cisco documentation (I don't copy paste on the post):
http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...
Thank you
PS: Please do not forget to rate and score as good response if this solves your problem
-
How to use ACS 5.2 to create a static ip address user for remote access VPN
Hi all
I have the problem. Please help me.
Initially, I use ACS 4.2 to create the static ip address for VPN remote access user, it's easy, configuration simply to the user defined > address assignment IP Client > assign the static IP address, but when I use ACS 5.2 I don't ' t know how to do.
I'm trying to add the IPv4 address attribute to the user to read "how to use 5.2 ACS", it says this:
1Ajouter step to attribute a static IP address to the user attribute dictionary internal:
Step 2select System Administration > Configuration > dictionaries > identity > internal users.
Step 3click create.
Static IP attribute by step 4Ajouter.
5selectionnez users and identity of the stage stores > internal identity stores > users.
6Click step create.
Step 7Edit static IP attribute of the user.
I just did, but this isn't a job. When I use EasyVPN client to connect to ASA 5520, user could the success of authentication but will not get the static IP I set up on internal users, so the tunnel put in place failed. I'm trying to configure a pool of IP on ASA for ACS users get the IP and customer EasyVPN allows you to connect with ASA, everything is OK, the user authenticates successed.but when I kill IP pool coufigurations and use the "add a static IP address to the user 'configurations, EzVPN are omitted.
so, what should I do, if anyboby knows how to use ACS 5.2 to create a user for ip address static for remote access VPN, to say please.
Wait for you answer, no question right or not, please answer, thank you.
There are a few extra steps to ensure that the static address defined for the user is returned in the Access-Accept. See the instuctions in the two slides attached
-
VPN IPSec using possible FWSM?
Hello
Is it possible to configure a module 6500 FWSM to allow a windows-based IPSEC VPN to put end to this and to allow access to the network protected inside.
Documentation for the FWSM talks about the configuration of the FWSM for remote access and management using a VPN. but it does not mention anything to have the vpn in the protected network.
Please tell me all the links on CCO.
Thank you
Verhasselt
Well, it's really simple...
Add the devices you have to complete the IPSec VPN. You're right, none of the components that you will allow you to IPSec VPN (at least not without assistance to complete a debit)...
Add a VPNSM (or the more fancy SPA-IPSEC solutions..) in each 6500 or put a VPN device size on each side...
Did she help?
-
Hi all
I need help with remote access vpn configuration. I want to some remote users who have access to the internet on their system to connect and access an application server in my seat social cisco vpn client user. I use Cisco 881. I am unable to use the SDM configuration because it seems that SDM is not supported by the router so I'm using command line. I'd appreciate any help I can get. Thank you.
This is the configuration I have:
VPNROUT #sho run
Building configuration...Current configuration: 6832 bytes
!
! Last configuration change at 10:50:45 UTC Saturday, May 30, 2015, by thomas
version 15.2
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname VPNROUT
!
boot-start-marker
boot-end-marker
!
!
logging buffered 51200 warnings
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login userauthen1 local
AAA authorization groupauthor1 LAN
!
!
!
!
!
AAA - the id of the joint session
iomem 10 memory size
!
Crypto pki trustpoint TP-self-signed-1632305899
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 1632305899
revocation checking no
rsakeypair TP-self-signed-1632305899
!
!
TP-self-signed-1632305899 crypto pki certificate chain
certificate self-signed 01
3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
69666963 31363332 33303538 6174652D 3939301E 170 3134 30313233 31323132
33325A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 36333233 65642D
30353839 3930819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
8100BC0C 341CD79B A38572CE 1F0F9A91 F96B133C A889B564 E8352034 1CF5EE4B
B505616B 6014041B EC498C0A F6C5CD2B F5BF62DA BD6E1C44 0C7B9089 1FD0C6E5
299CEB40 28CD3F3B ADE3468A B07AAA9F AC42F0A7 4087172A 33C4013D 9A50884D
5778727E 53A4940E 6E622460 560C F597DD53 3B 261584 E45E8776 A848B73D 5252
92 50203 010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355 D
551 2304 18301680 14E85AD0 DEF133D8 E09516FD 0AA5FDAD E10EAB1A FA301D06
03551D0E E85AD0DE 04160414 F133D8E0 9516FD0A A5FDADE1 0EAB1AFA 300 D 0609
2A 864886 818100A 5 05050003 5B23ED5B 9A380E1F 467ABB03 BAB1070B F70D0101
7A 218377 73089DC1 D32DA585 C5FD7ECE 0D000F96 7F3AB6CC 71509E8F 3F1C55AE
E37536A3 1008FBF9 A29329D5 6F76DDC0 AA1C70AE 958AAE5D 32388BE4 2C1C6839
0369 D 533 027B612C 8D199C35 C008FE00 F7E1DF62 9C73E603 85C3240A 63611D 93
854A61E2 794F8EF5 DA535DCC B209DA
quit smoking
!
!
!
no record of conflict ip dhcp
DHCP excluded-address IP 10.10.10.1
DHCP excluded-address IP 172.20.0.1 172.20.0.50
!
DHCP IP CCP-pool
import all
Network 10.10.10.0 255.255.255.248
default router 10.10.10.1
Rental 2 0
!
IP dhcp pool 1
network 172.20.0.0 255.255.240.0
domain meogl.net
router by default - 172.20.0.1
172.20.0.4 DNS server 41.79.4.11 4.2.2.2 8.8.8.8
8 rental
!
!
!
no ip domain search
IP domain name meogl.net
name of the IP-server 172.20.0.4
name of the IP-server 41.79.4.11
IP-server names 4.2.2.2
8.8.8.8 IP name-server
IP cef
No ipv6 cef
!
!
license udi pid CISCO881-K9 sn FCZ1804C3SL
!
!
username secret privilege 15 thomas 4 JXSizd1r/hMqPpGz94vKBb5somtpZLy03k50rJvHO6c
username privilege 15 secret 4 mowe hlfv/rdDRCAeTUzRXbOIfdaKhJCl1onoGdaQeaQsAnw
!
!
!
!
!
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
ISAKMP crypto client configuration group moweclients
XXXXXXX key
DNS 172.20.0.4
meogl.net field
pool mowepool
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac moweset
tunnel mode
!
!
!
Dynmap crypto dynamic-map 1
Set transform-set moweset
market arriere-route
!
!
card crypto client mowemap of authentication list userauthen1
card crypto isakmp authorization list groupauthor1 mowemap
client configuration address card crypto mowemap answer
mowemap 1 card crypto ipsec-isakmp dynamic dynmap
!
!
!
!
!
interface Loopback0
IP 172.30.30.1 255.255.255.0
IP nat inside
IP virtual-reassembly in
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
switchport access vlan 100
no ip address
!
interface FastEthernet3
no ip address
!
interface FastEthernet4
IP 41.7.8.13 255.255.255.252
NAT outside IP
IP virtual-reassembly in
intellectual property policy map route VPN-CLIENT
Shutdown
automatic duplex
automatic speed
mowemap card crypto
!
interface Vlan1
Description $ETH_LAN$
IP 10.10.10.1 255.255.255.248
IP tcp adjust-mss 1452
!
interface Vlan100
IP 172.20.0.1 255.255.240.0
IP nat inside
IP virtual-reassembly in
!
local pool IP 192.168.1.1 mowepool 192.168.1.100
IP forward-Protocol ND
IP http server
23 class IP http access
local IP http authentication
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
IP nat inside source overload map route interface FastEthernet4 LAT
IP route 0.0.0.0 0.0.0.0 41.7.8.12
!
access-list 23 allow 10.10.10.0 0.0.0.7
access-list 23 allow 172.20.0.0 0.0.15.255
access-list 100 permit ip 172.20.0.0 0.0.15.255 everything
access-list 144 allow ip 192.168.1.0 0.0.0.255 any
not run cdp
!
LAT route map permit 1
corresponds to the IP 100
IP 41.7.8.12 jump according to the value
!
route VPN-CLIENT map permit 1
corresponds to the IP 144
!
Line con 0
no activation of the modem
line to 0
line vty 0 4
access-class 23 in
privilege level 15
transport input telnet ssh
line vty 5 15
access-class 23 in
privilege level 15
transport input telnet ssh
!
!
endPlease the configuration above, give me the desired output.
Thank you.
Hello Thomas,.
I'm glad to hear that you have found useful in the example configuration.
I checked your configuration and everything seems ok with him, especially the statements of nat.
ip local pool mowepool 192.168.1.1 192.168.1.100 access-list 100 deny ip 172.20.0.0 0.0.15.255 192.168.1.0 0.0.0.255 access-list 100 permit ip 172.20.0.0 0.0.15.255 any route-map LAT permit 1 match ip address 100 ip nat inside source route-map LAT interface FastEthernet4 overload interface Vlan100 ip address 172.20.0.1 255.255.240.0 ip nat inside ip virtual-reassembly in
Try to generate ICMP traffic behind your 100 VLANS to the client VPN in order to answer the following questions:
-The router receives this traffic between VLAN100 unit?
-The router is encrypt this traffic, after receiving the ICMP packet?
#show crypto ipsec router its can help you with this question. Look for the program/decaps counters.
-The same, but the other way around (from VPN client to device behind VLAN100) try to locate the problem.
The following document explains more this crypto commands and debugs if necessary.
Maybe you are looking for
-
Retrieve the Info Mac hard drive?
I have the hard drive, I've pulled my broken MacBook Pro. I'm selling my MacBook Pro online, but I don't remember the card. I was able to pull the hard drive and it still works. What is there of nowhere that the information system is stored on the ha
-
Satellite 5205-S505 - support wide screen LCD TV?
I have a new wide screen LCD TV with a VGA port, I connected this with my old Satellite 5205-s505 via the VGA port as the second screen. But it displays 'unsupport signal' on the TV screen. Can someone have the answer.Thanks anyway.
-
Satellite 5105-s901: what RAM should I use for replacement
Toshiba Satellite 5105-s901P2.0, 15, 512, 60, RW/DV, WL, BT, 64VPART NO. PS511U-0P1RSXZSERIAL NUMBER 72065321PU-0 Dear Sir/Madam,5 years ago, that I bought in the city of St. Petersburg mentioned above for laptop. I amprofessional programmer, Geologi
-
Satellite P200-1EE - how to connect to the device using Belkin Mini Bluetooth Adapter
Please can someone help with my problem. I am running Vista sp2 and just bought one of these adapters.Tried to load the software and I'm having problems. This icon appears in the system tray, but no icon on the desktop. Now I have 3 other computers r
-
get the error message "status.msi".
After insalling windows XP Pro SP3 yesterday, everything was fine. Today, I turn on the computer and get this continuous message "status.msi" missing. I have accumulated my brain trying to find the file with no luck. Done a repair and still a problem