Impossible to get more than 1 channel to read with DAQmx cDAQ-9172 under Windows 7

I have the cell load, voltage, and input thermocouple connected to a cDAQ-9172. My sensors entries have been scaled and verified in MAX, and all of them work.  DASYLab 13, the driver is "dcDASY.dll" and the hardware configuration is "NI MAX.

When I add a task NEITHER-DAQmx Analog Input (that is, a set of scales) it appears correctly. If I add a second channel of the task and select it, I get this message:
'Channel of task name saved with the module is not available. DASYLab resets the module parameters for usable first channel name task. »
The name of the task remains the same for each new channel I have Add. If I change the name of the task by using the tab to the drop down menu, it says:
"You have configured several ways out for the module. If you modify the task, you lose the settings. You want to change the task? »
Both display the same data channels, and I can't work simultaneously several channels. It seems I missed something obvious, but I can't.

The parameters are:

Measurement and Automation Explorer 4.6.1
NOR-DAQmx 9.0

Material:-cDAQ-9172
Slot 1 - NOR 9215 (0-10 Vdc analog voltage)
Slot 2 - NEITHER 9211 (thermocouple)
slot 3 - NI 9481 (relay)
slot 4 - NI 9237 (entry deck w / excitement)
housing 5 - OR 9402 (DIO)
slot 6 - NI 9263 (0-10 Vdc output analog)

Thank you

You can't perform different tasks (continuous) HERE on a single chassis. The first tasks that starts will be 'the resource booking '.

Combine the AIs of the various modules in a single task (see photo): start by creating the task of thermocouple. Then add AIs 9237 (e.g. Kraft) and 9215 (volts) using the button with the blue, symbol. Set the mode of synchronization of the task of "continue". Save the task, start DASYLab (second photo).

Change a task (adding channels, etc.) to the MAX while DASYLab works always, will result in unexpected behavior. To synchronize the configuration of MAX with DASYLab, you will need to close/restart DASYLab or use the 'sync' of the function (see photo 3 "syncmax.jpg"). You can set this function as a shortcut by right-clicking on one of the eight green or grey circle things.

You should think about an update of the MAX/DAqmx drivers. 9.x is a little outdated.

Updated at least DAQmx 9.9, better 14.x or 15. 0 (stay far 15 1.x).

Tags: NI Products

Similar Questions

  • Selection of a subset of channels to read with DAQmx

    Hello

    I use a 32 channel NI9205 analog input module, connected with the chassis OR cDAQ-9174 and LABVIEW 2011.

    I created a task in the measurement and Automation Explorer who has 16 analog input of virtual channels (each of them with her has an entry configuration, scale, calibration, etc...). Inside LABVIEW, I opened this task to acquire some data, but I just want to read some of the 16 channels (defined by the user), not all, so before the "time DAQmx", I put a 'DAQmx reading node' and I put the ChannelsToRead with the names of the channels that I want to read. It seems to work, but when I put the acquisition rate it's error.

    The acquire module supports a rate of 250 kHz (divided by each channel). So if I put 5 channels to read, for example, it should work with a rate of up to 50 kHz. But whenever I try to use an acquisition rate higher than 15 625 kHz (which is 250 kHz/16) I get an error that says that the maximum rate is 15, 625kHz. As if I was using 16 channels of the task, but I'm not...

    Here the screenshot of channels read and sync configuration.

    Thank you
    Alexander

    Hello Alexander, and welcome to the forums,

    As odessy27 says that you do not reach the correct sample rate because the task is to be set up to read 16 channels; in spite of you more later by specifying which channels are to read.

    To preserve the configuration settings of your created able task and Automation Explorer (MAX), I recommend creating global chains of these. A Global channel will store your configuration for each physical channel and can be accessed from multiple tasks

    Creating a Global channel by the physical channels in your task of MAX right-clicking and then selecting create Global Channel. .

    You can drag these through to your block diagram and wire in the task/channels in the terminal of a function of mx-acquisition of data, as shown in the image below.

    If you change to a control by right clicking > change control channels can be set by the user and the maximum purchase price will go as planned.

    Concerning

    Jamie

  • SSL VPN 25 user license - impossible to get more than 2 SSL VPN connections

    Hello

    I just installed a user license user Premium 25 for SSL VPN on my Cisco ASA5505.  Even though it states that the license is installed I get still only two client Anyconnect SSL VPN connections and the third fails systematically.  What Miss me?

    Thanks for posting to the forum and that the problem has been resolved, and what caused the problem and what has been done to solve the problem. It's the most useful forum when people can read on a problem and can also read what the problem turned out to be and what was done to solve the problem, I think that it is also a good example to remind us that sometimes, the problem is not in our configuration, or even in the area that we administer. So sometimes we have to look beyond our normal home to find the source of the problem.

    The question mark it resolved makes it even more obvious to readers that they will find a solution to the problem. So thank you to mark the issue as resolved.

    HTH

    Rick

  • Try to use the same pattern for more than two channels (CSR configuration) with usb 6000

    Hello

    I am currently trying to implement a LabView code to get readings of voltage using 5 different places at the same time. I want to only use the first location in the ground and get 4 measurements of voltage between the ground and each of the other 4 channels. I use a USB 6000 which, for now, allows me to use the same pattern for only two channels. Is it possible to use the same pattern for 4 channels?

    Thank you

    Maria

    The images do not explain everything. You must explain what are the sensors. I think you totally wrong on how they should be linked. CSR, all sensors must be a common understanding and the outputs not individual channels as I have already explained. If you are unable to do this, you should probably not use CSR and you have the wrong data acquisition device. If you want a side of a sensor as a reference, you need differential connections.

  • Get samples of the clock machine (NEITHER with NOR cDAQ-9172-9422)

    Hey guys

    I'm trying to produce data for the position of a 1000 Hz all about stamping press with an absolute encoder which is connected to the NOR-DAQ.

    Two not that I am trying to program, but can not understand:

    (1) use a hardware clock to trigger the acquisition of the data at the selected speed

    (2) synchronize the three data acquisition modules I have to ensure that all data are received at the same time

    the material I have does not seem to have any counters. A few examples that I read would not go because of this.

    Any thoughts? If there is some examples/tutorials about this problem that I have missed please let me know.

    Thank you

    Hey, Rohan,.

    Thanks a lot for your help. I was talking to a National Instruments process engineer yesterday and it me that the problem was the vi calendar clock source option - instead of using AI/SampleClock, I had to use the time base of 100 kHz clock that did not appear in the list until I checked the option "ListAdvanced Terminal" in the name of e/s filtering dialog box. You must right-click the constant/control of the source of the clock and select I/O name filtering to open this dialog box.

    Thanks for all your suggestions, I'll try to apply it and check the performance.

    Nik

  • Presentation of master-detail Spry insert cannot get more than two columns?

    Ive been trying to get more than two columns only experiment with spry data sets and can not with the option to «insert master/detail layout» layout

    What I am doing wrong?

    ??????

    <! DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional / / IN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd" > ""
    "< html xmlns ="http://www.w3.org/1999/xhtml"" xmlns: spry = "http://ns.adobe.com/spry" > ""
    < head >
    < meta http-equiv = "Content-Type" content = text/html"; charset = utf-8 "/ >"
    < title > Untitled Document < /title >

    < script src = "SpryAssets/SpryData.js" type = "text/javascript" > < / script > "
    < script src = "SpryAssets/SpryHTMLDataSet.js" type = "text/javascript" > < / script > "
    < link href = "SpryAssets/SpryMasterDetail.css" rel = "stylesheet" type = "text/css" / > "
    < script type = "text/javascript" >
    DS1 var = new Spry.Data.HTMLDataSet ("benefitsdata.html", "bizben", {firstRowAsHeaders: false});
    < /script >
    < / head >

    < body >
    < div align = "center" >
    < div class = "MasterDetail" >
    < div spry: region = "ds1" class = "MasterContainer" >
    < div class = "MasterColumn" spry: repeat = "ds1" spry: setrow = "ds1" spry: hover = "MasterColumnHover" spry: select = "MasterColumnSelected" > {column0} < / div >
    < / div >
    < div spry: detailregion = "ds1" class = "DetailContainer" >
    < div class = "DetailColumn" > {column1} < / div >
    < div class = "DetailColumn" > {Column2} < / div >
    < div class = "DetailColumn" > {Column3} < / div >
    < / div >
    < br style = "" clear: both "/ >"
    < / div >
    < / div >
    < / body >
    < / html >

    ____________

    Spry framework all related examples are available here: http://adobe.github.com/Spry/samples/ you can take a look.

    On a sidenote, Spry has been deprecated and is no longer officially supported by Adobe: http://blogs.adobe.com/dreamweaver/2012/08/update-on-adobe-spry-framework-availability.htm l

    I would recommend that you switch to a jQuery library to your other needs.

  • Difficulties to get its entry set up and its entry to read more than 2 channels

    I need a multichannel audio for my project. I can't read more than 2 channels of my audio interface.

    The interface Im using is a mixer Alesis Multimix8 USB 2 and audio interface. It supports 10 channels and 2 outputs. With other software, I can read that all the channels simultaneously, without any difficulty of entry. When I specify the audio set up and read of input sound, to read more than 2 channels of any extra channel is a white signal. I'm using Labview 8.5 here.

    Have a look here

    http://forums.NI.com/T5/LabVIEW/play-waveform-express-VI-list-devices-on-front-panel/TD-p/1559336

  • Questions with more than 16 channels in daqmx

    I've implemented a .VI (from the pieces of the help on the forum) that I use with the NI USB-6225 to collect and record anywhere voltages 1-30 or more 4-20mA sensors (pressure, linear voltage,... etc.). I tried to implement the .VI to make it user-friendly so that a person could name each channel, as well as to set the duration record and frequency (ie the number of samples).  After the data were recorded, the .VI generates a time-stamped PDM file, a timestamped LVM file as well as a time-stamped LVM file for an average of all voltages on each channel.

    The problem, I noticed that whenever I have more than 16 channels activated, the saved values for channels 17 and higher pressures are wrong.  For example, the output voltages of 1 to 16 channels of a tension of 1.0 to 5.0 (which is expected) and 17-30 channels is negative or very small (0.100 volts).  I know that the NI USB-6225 is working properly because I created a simple .VI which simply uses the DAQ Assistant ouptut 30 channels on a waveform graph and all channels of reading in the range I'm waiting (1.0 to 5.0 volts).

    To me, it seems that there must be something in the DAQmx (as opposed to DAQ Assistant) I use my .VI who questions whenever I try to save more than 16 channels.  I just don't understand enough of labview to understand what may be the cause of this problem and I was hoping someone could point me in the right direction

    As you have not joined in the work programme, it is impossible to tell what you did differently. In this program, you do not specify the configuration of the inputs (simple nerve or diff).

    p.s., The program is bad need of major cleanup. Keep the program to a single screen. Simplify.

  • Get more than one individual target when activating a trigger

    Is there a way to get more than one target during the activation of a trigger. A target contains text, the other shows the photo or video. Each of them must be moved independently of the other and placed anywhere on the page. No idea how to do this? Thank you.

    You change the published HTML and assign it the same classes and IDs to several elements.

    Mylenium

  • can I use cloud adobe on more than 1 computer that I have an imac, a computer windows laptop and a macbook?

    can I use cloud adobe on more than 1 computer that I have an imac, a computer windows laptop and a macbook?

    Yes, you can install and use the Adobe application on 2 computers (no more than 2).

    You can get the details, http://www.adobe.com/products/creativecloud/faq.html

    Can I use the software that I download creative cloud on several computers?

    Yes, you can use applications desktop cloud creative on two computers at once, regardless of the operating system of the individual associated with the composition of the creative cloud. See the page of theproduct license agreements for more information.

  • Failed to get more than 1 email on the shipment line [blush].

    Hello and thank you for your time, just use Mozilla for 2 months [ex user of outlook express]. I want to send an email, the address is available for good, now I want to include a different address, as soon as I get the address first becomes 2nd red and my second address is not, only the first letter is then I quit smoking and do not send anything. I need help, my mail before develops. Thank you, frosty.

    Thanks Todd, had the opportunity to move your suggestions and I have learned from them, I now can I send more than one forward both by using the Enter key, thank you for helping me along the way. Frosty

  • I can't get more than 3 "To" fields and need more - help!

    If I want to send an email I get only 3 "to:" fields before entering the title field. Because I can not type in more than one name in each field, how can I send the email recipients a dozen (without going through the address book for each of them, which seems a very tedious way to do)?
    I am a new user of Thunderbird, so forgive me if this is a stupid question, but I can't find the answer in the FAQ.

    Press ENTER after you have entered the third e-mail address.

  • PIXMA MP210. When I print, I get more than one sheet of paper that goes thru.

    When printing, more than one sheet of paper passes through. So far, it still prints what I need. Then I get a message that there is a paper jam. I took almost all of the pieces, but can find no documents or anything in animal feed. I have not changed anything before starting.

    All solutions?

    Carl

    Hi Carl54,

    Performing a cleaning of the printer roller may solve the problem you are having.  To do this, please follow the steps located here.  We recommend that at least three cleaning of rollers on the printer.

    It has not responded to your question or problem? Please call or write us using one of the methods on the page contact us for further assistance.

  • New Predator X 34-failed to get more than 60 Hz

    I'm curious to know if anyone has a fix/recommendations for things to try in this situation: I just got the X-34 last weekend.  I'm running it with a 980ti SC EGVA + on Windows 10 with Nvidia driver 359.06 version.  My problem is that I can't monitor running more than 60 Hz.  In the OSD, I turned it on IT with a Max of 100 refresh.  When I run the Nvidia Control Panel, I see that the monitor is running at 3440 X 1440 and Gysnc works.  However, when I select anything that exceeds 60 Hz and click on apply, the app immediately goes back to 60 Hz.  When I try to change the Hz using the Advanced view setting Windows 10, I can get it to apply a setting higher than 60 Hz (80, 90, etc.) but will not take the X 34 it - it wobbles black several times then past in black and will not appear until I have go back to 60 Hz.

    Feedback would be to understand whether it is a fixable problem (software problem or setting) or if I have a bad screen and need to RMA it back to the supplier.

    Thank you!

    JV1

    It's great to hear!  I know it seems strange, but the cable carries the bandwidth of the signal and if the cable is not of sufficient quality, it can cause these issues.  Longer cables tend to degrade the signal on the length, that's why you should always use the shortest cable possible for video signals

    Please do not forget to mark my post, or your response indicating the cable swap patch worked as a 'solution' here so that others with the same problem can see and find the solution quickly and the thread will be marked as "resolved".

    Cheers and happy playing,

    Vand

  • on my desktop screen, icons are real blurry changed resolution and it wont let me get more than 60 hertz__

    Remember - this is a public forum so never post private information such as numbers of mail or telephone!

    Ideas: I tried to change the resolution and refresh rate, but which is not help and find a way back to the factory setting on the monitor or if it is a good idea. It won't let me go higher than 60 hertz says it's all my screen to refresh 19 inch flat screen made by dell please help out of options

    • You have problems with programs
    • Error messages
    • Recent changes to your computer
    • What you have already tried to solve the problem

    Was this work very well at a time earlier - I hope that recently?  Was your monitor there ever a better than 60 Hz resolution? Do you know when this problem started?  Try a system restore to a point in time BEFORE the problem started.  Here is the procedure: http://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/.  Don't forget to check the box to show more than 5 days of restore points.  If the first attempt fails, then try an earlier point or two.  NOTE: You will need to re - install any software and updates that you have installed between now and the restore point, but you can use Windows Update for updates.

    Go to the Dell Support and enter your Service tag number.  Who should put up your system, including your monitor (assuming that your system is Dell - otherwise just check the make and model of the monitor) and get the latest device drivers available for this monitor and your version of Vista.  Once you have the drivers, you can install them through the Device Manager (start / Control Panel / Device Manager) as follows: http://www.vistax64.com/tutorials/193584-device-manager-install-driver.html. or it may be a simple executable file - it depends what downloads.  Given that this is the view I'd do the same for your video card (that this either Dell or another manufacturer's).  Once you have installed these drivers, restart and go to Start / Control Panel / customization / display settings and see if you have more options for resolution and can get things the way you want them to be.

    I hope this helps.  If this isn't the case, post back with the results of the above options, and any other information you can give us on the devices and the problem. Let's see if we can come up with a few other options to try.

    Good luck!

    Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

Maybe you are looking for