Impossible to get over 130mbps
I have a router 600n wrt and a wusb300n and can only get a max of 130mpbs connection.
Here are my settings basic wireless
Here is my wireless security settings:
What can I do to get my bandwidth closer to 300mbps brand?
Change the channel to 11.
Click on advanced wireless
settings > change the tag at 50 interval > change the Fragmentation
Threshold to 2304 change the RTS threshold to 2304 > click on "save settings".
Tags: Linksys Routers
Similar Questions
-
Satellite U500-176: Impossible to get an HDMI output to work on television or monitor
Hello
I have a new Satellite U500-176 but impossible to get the HDMI to work on a TV or monitor.
Usually, when the monitor is connected and I press Fn + F5 I get only the 1 option (LCD).
Occasionally, the HDMI options work but when I select one it goes to the screen and runs successfully for a few seconds then automatically returns.Any ideas?
See you soon,.
Roy.Hello
Hmm, what operating system are you using?
Was - this operating system preinstalled by Toshiba?Please take a look in the BIOS. There should be HDMI settings. Please check if it is enabled.
In addition, I would recommend checking the graphics card driver update.What version of BIOS you are using the most recent?
-
My "Sweep" block future messages Hotmail is maxed out at about 500 addresses. Blocked addresses can be developed? I get over 100 emails a day I want to block forever.
Hello
Answers is a peer group supported and unfortunately has no real influence on Hotmail.
HotMail has its own Forums, so you can ask your questions there.
Windows Live Solution Center - HotMail - HotMail Forums Solutions
http://windowslivehelp.com/Hotmail - Forums
http://windowslivehelp.com/forums.aspx?ProductID=1Hotmail - Solutions
http://windowslivehelp.com/solutions.aspx?ProductID=1How to contact Windows Live Hotmail Support
http://email.about.com/od/hotmailtips/Qt/et_hotmail_supp.htmWindows Live Hotmail Top issues and Support information
http://support.Microsoft.com/kb/316659/en-usCompromised account - access unauthorized account - how to recover your account
http://windowslivehelp.com/solution.aspx?SolutionID=6ea0c7b3-1473-4176-b03f-145b951dcb41Hotmail hacked? Take these steps
http://blogs.msdn.com/b/securitytipstalk/archive/2010/07/07/Hotmail-hacked-take-these-steps.aspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
-
Impossible to get Vista SP2 installed
Impossible to get SP2 to install on my windows vista 32 bit
Download the SP2 installation file in a folder on your hard drive, then double-click it to start the installation.
Windows Server 2008 Service Pack 2 and Windows Vista Service Pack 2-five language standalone (KB948465)
http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=a4dd31d5-F907-4406-9012-a5c3199ea2b3&displaylang=enService Pack 2 for Windows Server 2008 and Windows Vista
http://TechNet.Microsoft.com/en-us/Windows/dd262148Never be afraid to ask. This forum has some of the best people in the world to help.
-
After the Windows 10 update (don't like it) and go back to Windows 7 Home premium, impossible to get the Windows Update to run.
Sorry, but KB3153199 has replaced two times at the same time. It takes the new version of the Windows Update client to correct known issues.
http://support.Microsoft.com/kb/3161608
Manual installation requires a continuous search to be interrupted. The value of the automatic updates to "never check updates" and then restart Windows.
Best regards, VZ
-
Impossible to get brother printer to run on windows 8 model is MFC 685 - CW... also can't download itunes... Help, please!
Hi Dominic,
I understand that you are unable to respond to this thread and created a new thread.
As restart the print spooler does not solve the problem, please reinstall the printer and then check if that helps.
Check out the following link to resolve the problem of iTunes.
http://support.Apple.com/kb/HT3204
Hope that the information provided is useful.
-
With the help of LR4 with Windows 8 - impossible to get the images to desempilement.
Using LR4 with Windows 8 - impossible to get the images to desempilement.
Right click on the picture, select stacking, select Unstack
-
Newly build Production environment (don't use it yet)
OS: Linux redhat 64-bit 2.6.18
Cluster version: 11.2.0.4
This environment clusterware installed last December, we are trying to install oracle RDBMS, so try to first stop the crs. However on node 1, the v$ asm_diskgroup shows nothing under total_mb /free_mb on diskgroup OCR. and stop the crs shows: impossible to get in touch with the loan of cluster service.
Alerts cluster log shows below:
2014-03-25 03:50:01.429:
[crsd (8608)] CRS-1013: the location of the OCR in ASM disk group is inaccessible. Details in u00/app/11.2.0.4/grid/log/oprd100/crsd/crsd.log.
2014-03-25 03:50:01.433:
[crsd (8608)] CRS - 0804:Cluster Ready Service interrupted due to the Oracle Cluster registry error [PROC-26: error when accessing the physical storage]
]. Details at (: CRSD00111 :) in u01/app/11.2.0.4/grid/log/orpd100/crsd/crsd.log.)
2014-03-25 03:50:02.123:
[ohasd (12490)] CRS - 2765:Resource 'ora.crsd' failed on the server "orpd100".
2014-03-25 03:50:03.407:
[crsd (8623)] CRS-1013: the location of the OCR in ASM disk group is inaccessible. Details in u01/app/11.2.0.4/grid/log/orpd100/crsd/crsd.log.
2014-03-25 03:50:03.411:
[crsd (8623)] CRS - 0804:Cluster Ready Service interrupted due to the Oracle Cluster registry error [PROC-26: error when accessing the physical storage]
The NEWSPAPER of the ASM alerts:
Wed Mar 25 03:21:49 2014
WARNING: Waited 15 seconds IO to write to the disk of PST 1 in Group 1.
WARNING: Waited 15 seconds to write IO to disk of PST 2 in Group 1.
WARNING: Waited 15 seconds IO to write to the disk of PST 1 in Group 1.
WARNING: Waited 15 seconds to write IO to disk of PST 2 in Group 1.
Wed Mar 25 03:21:49 2014
NOTE: process _b000_ + asm1 initiating (21071) 1.1807368888 disk offline (OCR_0681_2EF4) with mask 0x7e in Group 1
NOTE: process _b000_ + asm1 initiating (21071) 2.1807368889 disk offline (OCR_0681_2EF5) with mask 0x7e in Group 1
NOTE: check PST: grp = 1
GMON seeking ways of disc for Group 1 to 5 pid 27, DiSo 21071
ERROR: read no quorum within Group: required 2 found 1 records
NOTE: audit PST grp 1 fact.
NOTE: start the PST update: grp = 1, dsk = 1/0x6bba42b8, mask is 0x6a, op = clear
NOTE: start the PST update: grp = 1, = 2/0x6bba42b9 dsk, mask is 0x6a, op = clear
GMON update modes of disk for the Group 1 to 6 for 27, DiSo 21071 pid
ERROR: read no quorum within Group: required 2 found 1 records
Wed Mar 25 03:21:49 2014
NOTE: disassembly of the cache (not clean) Group 1/0x35AAB27B (OCR_DATA)
WARNING: For disk offline OCR_0681_2EF4 0x7f mode failed.
2 node rac cluster is normal. We were able to stop the crs without force.
What should I look at to understand what is happening here?
Thanks to adavnace.
WARNING: For disk offline OCR_0681_2EF5 0x7f mode failed.
NOTE: e-mail CKPT suspend pins Unix process pid: 21073, image:
No default value is 1 M
-
Impossible to get anything I photo shopped with Adobe Elements at a Wal-Mart / Walgreens. Never had a problem with the photos, saving and printing with Corel Photshop
File > save under of the editor and use the drop-down list to change the file type.
-
Downloaded standalone 6 Lightroom on a MacBook Pro. Impossible to get a program to open - an internal error cannot create the required folder. Any suggestions about how to proceed?
Hi woodysk
Greetings.
- You will need to read and write permissions on the Adobe folders manually.
Please follow the steps below:
- Right-click on the icon in the Finder and select the 'Go - To' folder option.
- You will get a text box, type in the following command and then press the 'return '. (Don't miss ~ symbol)
- ~/Library
- Then go to the Application Support > Adobe.
- Right-click on the Adobe folder, then select the GetInfo.
- Expand the section sharing & permissions.
- Click on the padlock icon in the lower corner on the right. Enter your administrator user name and password when you are prompted, and then click OK.
- Please click on '+' symbol, it will open the list of user accounts.
- Add all of the user accounts and then give permission to "Read & write" to all user accounts. (If not agree, just add currently logged in username and administrator)
- Click the gear icon and select apply to closed. Close the dialog box for information.
- Then launch Lightroom application and check.
Let me know if still face you any issue.
Concerning
Rohit
-
Recently I replaced my hard drive on my imac and now when I try to open Ps Id and another app for my CS4 I have error 150:30. How can get over this? Thanks much for any help.
Hello
Please see error "Licensing has stopped working". Mac OS
Kind regards
Sheena
-
My Mac crashed and I had to reinstall everything. Photoshop keeps giving me the following error message, even after multiple uninstalls and reinstalls: error 16. It is impossible to get support from adobe - no one to call. It's for Photoshop 13.0.6 and Mac Os 10.10.5 help please. Please respond by email to [email protected]
I got this error 16 experience on my Macbook. The permissions for the Application Support folder have been changed.
A simple fix Terminal can take care of that.
Open Terminal (you can just tap Terminal in Spotlight to find it).
Copy and paste this command in Terminal: sudo chmod-r 777 library/Application\ Support / Adobe
Press enter, give your password if requested, and then try again. You may need to restart your Mac.
Gene
-
Just downloaded latest updates Camera Raw update for use with my new Sony RX100 M3 but still impossible to get the RAW files to open it. Any suggestions?
Nevermind, I finally got it to work, thanks!
-
Impossible to get Min, Max and median of the values in the date range values
Hello
I had a requirement as to show the data of each charge group of wise men as '< 100' ' 100-199 "" 200-299 "" 300-399 "400-499, 500-599 600-699 700-799 800-899 900-999 > = 1000 '"»
With the query be able to get the count between the beach and the total below. But impossible to get the Min and Max values for this range. For example if the County < 100 is 3 then in these 3, the lowest value is need to display in the min. Idem for Max column also.
In the light of the median value on these values.
Thanks in advance.
Requirement is as below:
State < 100 100-199, 200-299 300-399 400-499, 500-599 600-699 700-799 800-899 900-999 > = 1000 Min Total median Max
AK 1 2 0 4 1 4 4 35 35 4 1 $25 $85 850 $1,200
AL 0 0 2 27 10 17 35 2 2 35 0 $103 100-$1 500 750
* "QUERY ' * '"
WITH t AS
(SELECT 'AL' State, 12 DUAL FROM VALUE
UNION ALL
SELECT 'AL' State, 67 FROM DUAL VALUE
UNION ALL
SELECT 'AL' State, 23 FROM DUAL VALUE
UNION ALL
SELECT 'AL' State, 12 DUAL FROM VALUE
UNION ALL
SELECT 'AL' State, 12 DUAL FROM VALUE
UNION ALL
SELECT 'AL' State, 78 FROM DUAL VALUE
UNION ALL
SELECT 'AL' State, 34 FROM DUAL VALUE
UNION ALL
SELECT 'AL' State, 4 DUAL FROM VALUE
UNION ALL
SELECT 'AL' State, 12 DUAL FROM VALUE
UNION ALL
SELECT 'AL' State, 15 VALUE FROM DUAL
UNION ALL
SELECT "AZ" State, FROM DUAL VALUE 6
UNION ALL
SELECT "AZ" State, 123 FROM DUAL VALUE
UNION ALL
SELECT "AZ" State, 123 FROM DUAL VALUE
UNION ALL
SELECT 'MY' State, 23 FROM DUAL VALUE
UNION ALL
SELECT 'MY' State, 120 FROM DUAL VALUE
UNION ALL
SELECT 'MY' State, 456 FROM DUAL VALUE
UNION ALL
SELECT 'MY' State, 11 FROM DUAL VALUE
UNION ALL
SELECT 'MY' State, 24 FROM DUAL VALUE
UNION ALL
SELECT 'MY' State, 34 FROM DUAL VALUE
UNION ALL
SELECT 'MY' State, 87 DUAL FROM VALUE
UNION ALL
SELECT 'MY' State, 23 FROM DUAL VALUE
UNION ALL
SELECT 'MY' State, 234 DUAL FROM VALUE
UNION ALL
SELECT 'MY' State, 789 FROM DUAL VALUE
UNION ALL
SELECT "HD" State, VALUE FROM DUAL 54321).
-End of test data
AS T1
(SELECT State,
NVL (COUNT (DECODE (VALUE, 0, 0)), 0) '< 100 ',.
NVL (COUNT (DECODE (VALUE, 1, 1)), 0) '100-199.
NVL (COUNT (DECODE (VALUE, 2, 2)), 0) '200-299.
NVL (COUNT (DECODE (VALUE, 3, 3)), 0) '300-399.
NVL (COUNT (DECODE (VALUE, 4, 4)), 0) '400-499.
NVL (COUNT (DECODE (VALUE, 5, 5)), 0) '500-599,'
NVL (COUNT (DECODE (VALUE, 6, 6)), 0) '600-699.
NVL (COUNT (DECODE (VALUE, 7, 7)), 0) '700-799.
NVL (COUNT (DECODE (VALUE, 8, 8)), 0) '800-899.
NVL (COUNT (DECODE (VALUE, 9, 9)), 0) '900-999. "
NVL (COUNT (DECODE (VALUE, 10, 10)), 0) ' > = 1000.
(SELECT STATE,
CASE
WHAT VALUE < 100 THEN 0
WHAT A VALUE BETWEEN 100 AND 199 THEN 1
WHAT VALUE BETWEEN 200 AND 299, THEN 2
WHAT VALUE BETWEEN 300 AND 399 THEN 3
WHAT VALUE BETWEEN 400 AND 499 THEN 4
WHAT VALUE BETWEEN 500 AND 599 5 THEN
WHAT VALUE BETWEEN 600 AND 699 6 THEN
WHAT VALUE BETWEEN 700 AND 799 THEN 7
WHAT VALUE BETWEEN 800 AND 899 8 THEN
WHAT VALUE FROM 900 TO 999 9 THEN
WHAT VALUE > = 10 THEN 1000
END
VALUE
T)
GROUP BY State)
SELECTION STATE,
"< 100."
"100-199.
"200 299",
"300-399.
"400-499.
'500-599,'
"600-699.
"700-799.
"800-899.
"900-999."
"> = 1000."
'< 100 '.
+ "100-199.
+ "200-299.
+ '300-399.
+ '400-499.
+ "500-599.
+ '600-699.
+ "700-799.
+ "800-899.
+ '900-999 ".
+ ' > = 1000.
in total,.
less ("< 100",)
"100-199.
"200 299",
"300-399.
"400-499.
'500-599,'
"600-699.
"700-799.
"800-899.
"900-999."
("> = 1000 ') min_val,.
largest ("< 100",)
"100-199.
"200 299",
"300-399.
"400-499.
'500-599,'
"600-699.
"700-799.
"800-899.
"900-999."
("> = 1000 ') max_val
FROM t1
/Why not keep it simple?
WITH t AS (SELECT 'AL' state, 12 VALUE FROM DUAL UNION ALL SELECT 'AL' state, 67 VALUE FROM DUAL UNION ALL SELECT 'AL' state, 23 VALUE FROM DUAL UNION ALL SELECT 'AL' state, 12 VALUE FROM DUAL UNION ALL SELECT 'AL' state, 12 VALUE FROM DUAL UNION ALL SELECT 'AL' state, 78 VALUE FROM DUAL UNION ALL SELECT 'AL' state, 34 VALUE FROM DUAL UNION ALL SELECT 'AL' state, 4 VALUE FROM DUAL UNION ALL SELECT 'AL' state, 12 VALUE FROM DUAL UNION ALL SELECT 'AL' state, 15 VALUE FROM DUAL UNION ALL SELECT 'AZ' state, 6 VALUE FROM DUAL UNION ALL SELECT 'AZ' state, 123 VALUE FROM DUAL UNION ALL SELECT 'AZ' state, 123 VALUE FROM DUAL UNION ALL SELECT 'MA' state, 23 VALUE FROM DUAL UNION ALL SELECT 'MA' state, 120 VALUE FROM DUAL UNION ALL SELECT 'MA' state, 456 VALUE FROM DUAL UNION ALL SELECT 'MA' state, 11 VALUE FROM DUAL UNION ALL SELECT 'MA' state, 24 VALUE FROM DUAL UNION ALL SELECT 'MA' state, 34 VALUE FROM DUAL UNION ALL SELECT 'MA' state, 87 VALUE FROM DUAL UNION ALL SELECT 'MA' state, 23 VALUE FROM DUAL UNION ALL SELECT 'MA' state, 234 VALUE FROM DUAL UNION ALL SELECT 'MA' state, 789 VALUE FROM DUAL UNION ALL SELECT 'MH' state, 54321 VALUE FROM DUAL) SELECT state , NVL( COUNT( case when VALUE < 100 then 0 end ), 0 ) "<100" , NVL( COUNT( case when VALUE between 100 and 199 then 0 end ), 0 ) "100-199" , NVL( COUNT( case when VALUE between 200 and 299 then 0 end ), 0 ) "200-299" , NVL( COUNT( case when VALUE between 300 and 399 then 0 end ), 0 ) "300-399" , NVL( COUNT( case when VALUE between 400 and 499 then 0 end ), 0 ) "400-499" , NVL( COUNT( case when VALUE between 500 and 599 then 0 end ), 0 ) "500-599" , NVL( COUNT( case when VALUE between 600 and 699 then 0 end ), 0 ) "600-699" , NVL( COUNT( case when VALUE between 700 and 799 then 0 end ), 0 ) "700-799" , NVL( COUNT( case when VALUE between 800 and 899 then 0 end ), 0 ) "800-899" , NVL( COUNT( case when VALUE between 900 and 999 then 0 end ), 0 ) "900-999" , NVL( COUNT( case when VALUE >= 1000 then 0 end ), 0 ) ">=100" , count( value ) "total" , min( VALUE ) "min" , max( VALUE ) "max" , avg( VALUE ) "avg" , median( value ) "median" from t group by state
-
Impossible to get a substring of the current s URL page
Hello
I have a very strange problem with the URL returned by GSF. I seem to be impossible to get a substring of the URL - the String.substring (int, int) method does not appear to return the expected results. It seems that other methods of strings (such as the indexOf (String)) seem to be operating on the chain of substring returns a part, rather than on the chain saw when the url is printed in its entirety. The corresponding code is less to:
-----
AssetApiWraCoreFieldDao wraDao = new AssetApiWraCoreFieldDao (ics);
String wrapperCurrPage = ics. GetProperty ("com.fatwire.gst.foundation.url.wrapathassembler.dispatcher", ServletRequest.properties ", true);
WebReferenceableAsset wraCurrPage = wraDao.getWra (pageId);
String theLongUrl = new String ((new WraUriBuilder (wraCurrPage, wrapperCurrPage)) .toURI (ics));
This displays the correct URL (http://www.example.com/page)
out.println ("FULLURL:" + theLongUrl.toString ());
This displays the first 25 characters of a string of unknown characters (satellitescheme://SSURI/?)
out.println ("substring:" + theLongUrl.toString () .substring (0.25));
-----
All help to work out what happening would be appreciated – as far as we can tell GSF (or maybe WCS) are originally String to behave in a non-standard way.Hi 950972,
There is little of the magic that is you fool. Basically, if you change out.println () System.out.println () you will see TWO URLS begin with satellitescheme: / /. What is happening, this is the URL which are produced by the ISU Sites still are built with a satellitescheme://...#satellitefragment. Then, what is Server RHN Satellite will process the result and replace the strange chain with one that fits your URL assembler (and in this case, you use the GSF assembler).
In your code of substring, you are breaking the special chain and are cutting the encoded URL. RHN Satellite Server does not see the prefix and the suffix combined, so it does not have to make the substitution.
That's why Your ' e see what see Your ' e.
A big question is however, why you try to process the URL generated by the API. I guess that sort of substitution will happen, but that should not be done. What you trying to do? I'm sure we can find the right way to achieve your goals.
Kind regards
Tony
Maybe you are looking for
-
Hi all! Since upgrading to FCP 10.2.3, 80% of my images still in the movies and work, the other 20% weird color lines to this topic, see the image below. I tried to re - register and again add the media to the event, etc. and also deleted the files g
-
!! Lenovo M490s function keys and hibernate problem!
Hello world! I bought the laptop Lenovo M490s week last without BONES. I installed Windows 7 Professional x 64 retail. First of all, I could not find the software that controls the function keys. After installing each driver and software support page
-
Table of horodateurs multiple waveform
How to make more than two or three timestamps along the x-axis of a graph of wavefrom? Ideally I would like to have 5 scale on my map markers that update with value timestamp that happens with the data being plotted? Currently, I see a timestamp on
-
Pavilion CTO 2200 g6: test specifications for compatibility with windows 10
I have a Pavilion g6 CTO 2200 laptop comes with Windows 8 is installed. I bought it at the end of 2012. How long will it be until this HP tests to allow Windows 10? I want this OS.
-
Error at startup "unmountable_boot_volume" in Vista
I have 2 computers, age less than 2 years and with vista, as well as in the 3 weeks apart, I received an error message of "unmountable_boot_volume". At this point is it possible to get the computer to boot? The first computer I've already replaced