Impossible WAP54G access default IP address

Similar Questions

• I have a HP OfficeJet Pro K550 with a default IP address and I can't access it to change.

  Because the static IP address of the default printer is not in my subnet and my network doesn't have a DHCP server, that I am unable to access the settings, I need to change the IP address that I can use.  I use Windows 7 64 bit and am connected to the printer via the USB port.  I don't know if I got a my network IP address I could type in the address bar and open many more parameters, but I'm not sure how as the default IP address is not on my network.

  I guess that you can not connect to the printer subnet temporarily?  You can disconnect the printer from this subnet temporarily?  You can connect an Ethernet between your PC and the printer cable?

• Impossible to access remotely to Zoneminder on port 80

  I have a Cisco Linksys E2500 modem and I can't access Zoneminder which is basically a Linux video security DVR software package.  It runs on a Ubuntu Linux server.

  I have HTTP port 80 forwarded to the address static IP of the server Ubuntu but I repeatedly get an error indicating that the connection has expired whenever I try to access Zoneminder remotely as in access it remotely from a coffee shop.

  I have absolutely no problem to access the Zoneminder when I on my home LAN.

  I can access other software from remote sites on the parameters of the port 4369 with a favorite TCP protocol.  In other words, 4369 port is forwarded to an another Windows workstation with a static IP address assigned. Absolutely no problem with 4369 port forwarding.

  Also, I tried port 80 on the site, YouGetSignal, which is used to test port forwarding.  The Web site indicates that port 80 is closed.  But when I test port 4369, the site indicates that the port is open.  Zoneminder that uses port 80 is fully operational when I test port 80 via YouGetsignal.

  My ISP told me that they do not block the ports including port 80.

  Any help would be greatly appreciated

  Thanx

  Try the following steps:

  [A] with the help of the Cisco Connect software (if at all, you have installed the router using this software)

  1] open the software and go to the option that says "settings of the router.

  [2] then click on the option that says 'Advanced settings', which will take you to the router configuration page.

  [3] then click on disable SPI Firewall Protection Security tab, uncheck the box filter anonymous Internet requests...

  [B] If you have not installed Cisco connect then you can connect to the router's user interface using its default IP address in the browser which is 192.168.1.1 and enter "admin" as password empty username field. This will take to the web interface of the router and then follow the steps as indicated above to make the changes.

• Impossible to access anything whatsoever in the Panel, limited access to internet

  Impossible to access anything whatsoever in the Panel, run antivirus, nothing found, limited access to internet too.  Don't know what to do.

  Hello

  1. don't you make changes to the computer before the show?
  2. what happens when you try to access the Internet?
  3. what web browser you use to access the Internet?
  4. do you get the error message?

  Method 1
  Step 1: I suggest to start the computer in safe mode with network and check if you are able to access control panel and Internet.

  Startup options (including safe mode)
  http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode
  Step 2: If you are able to access the Control Panel on safe mode, then I suggest you perform the clean boot and remove the program that is causing the problem. Make sure that you disable also all firewall and antivirus when you perform the clean boot.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software
  Note: Microsoft does not recommend that you disable the antivirus protection in most conditions. Disable the antivirus protection that temporarily to restore a computer.
  Note: follow step 7 clean boot KB929135 article to reset the computer in normal mode.

  Method 2
  I suggest you run virus scan online by using the Microsoft safety scanner.

  Microsoft safety scanner
  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: when you do an antivirus online, you will lose data that are affected by the virus. Microsoft is not responsible for the loss of this data.

  Method 3
  I suggest you to create the new user account and check if the problem persists.

  Create a user account
  http://Windows.Microsoft.com/en-in/Windows7/create-a-user-account

  If everything works well in the new user account, then I suggest you to transfer data and settings to the fixed aid corrupt profile.

  Difficulty of a corrupted user profile
  http://Windows.Microsoft.com/en-in/Windows7/fix-a-corrupted-user-profile

• where can we find embedded oc4j option to set the default ip address in JDeveloper 10 G

  Hi all
  
  I installed the Jdeveloper 10 G in the system, I made all configurations correctly, but when I m running the EmpSearch page, it gives the error below
  
  Explanation: The IP address for the site you requested is not found.
  
  Try the following:
  Refresh the page: search for the page again by clicking the Refresh button. The timeout occurred due to Internet congestion.
  Spell check: check that you typed the Web page address correctly. Make sure the address of the Web page is correct and only contains no typo.
  Access from a link: If there is a link to the page you are looking for, try to access the page from this link.
  If you are still not able to view the requested page, try contacting your administrator or helpdesk.
  
  normally, in Jdeveloper 9i, we select the default IP address local in tools-> References-> Embedded OC4J
  
  but the same option that I could find in Jdeveloper 10 G, m
  
  Please guide me for the same thing.
  
  thanx
  
  Pratap

  Go to tools-> embedded OC4J preferences-> Global-> start

• When closing Firefox 13.01 I always get this pop-up: Exception EAccessViolation in module ntdll.dll to 000222 B 2. Access violation at address 77BF22B2 in module

  When closing Firefox 13.01 I always get this popup:
  Exception EAccessViolation in module ntdll.dll to 000222B 2. Access violation at address 77BF22B2 in module 'ntdll.dll '. Writing of
  address 00000008.
  With previous versions of FF it never happened.
  Any solution?

  Hello

  Please check if this happens in a new profile. If the new profile is correct, you can then reset Firefox on the old (previous) profile via the help (Alt + H) > troubleshooting information.

• Error "Library not registered" and "access violation at address 00000000. Read of address 00000000 "while trying to play Call of Duty 2 on Windows 7 64 bit

  Original title: Call of Duty 2 on windows 7: first window said: library not registered. After a minute, seven or more pop-up windows to say the same thing: access violation at address 00000000. Read of address 00000000

  I tried to play Call Of Duty 2 on windows 7 64 premium.  After installation, if I choose to click on the shortcut on the desktop, it keeps invites me to insert the correct CD in the drive.  That right is already in the drive.  If I have the game from the CD autorun, it invites library not registered.  Then opens upward of seven windows or more with the same message: access violation at address 00000000. Read of address 00000000.  the map system, game and video have all been updated and installed the latest patch for Call of Duty 2.  The funky thing is, if I use the fix offered for Vista I can get the multiplayer game to work, but the single player mode is still inaccessible.  I tried changing the compatibility, tried to use the option of windows XP mode and tried to open it in a new window and ran it under administrator.  nothing has worked, suggestions?

  I have thought about it myself, do what I tried above and activate the function of compatibility with Windows Vista service pack 2.  If you do not know the fix vista, click Start, Control Panel, hardware and sound, click sound, and then click the recording TAB.  Right click on a space in the tab itself, when see her disable devices is displayed click on to show them.  stereo mix is show in the tab, right click on that and turn on.  Only, remember, insert the CD, do not autorun installation just right click on the icon setup on the CD itself and open a new window.  run as administrator and install.  After that, go ahead and install the latest version of Patch 1.3 for Call of Duty 2.  When all is said and done don't forget to change the compatibility mode to Windows Vista service Pack 2. Note to Microsoft: Windows XP mode is a great idea, except that you dropped the ball twice, #1 - should have a version of it to support windows 7 Edition home premium for topics such as this for the public #2 - you must enable a way to get the video settings within the windows XP mode , in short to make a windows operating system that will play a game out there that has already been done to PC.

• TuneUp Utility has been installed on a trial basis, it changed the things that made it impossible to access the C:\ drive to install the important updates and uninstall Tuneup Utilities.

  On my old Dell with Windows XP I installed Tuneup Utility on an experimental basis, it changed things that made it impossible to access the C:\ drive to install the important updates and uninstall Tuneup Utilities.

  Anyone have a solution?

  Help, please.

  Software support to the YOU seem hopeless, they donot even read the request entirely to meet the last 8 weeks and many emails in series.

  Hello

  I suggest you to follow the steps in this link and check if it helps:

  Method 1:
  Try to uninstall the utility and check if it helps:
  http://support.Microsoft.com/kb/307895

  Method 2:
  Try to restore the computer to the point before you install the utility and check if it helps.
  http://support.Microsoft.com/kb/306084

  It will be useful.

• How can I make my default email address Qwest and get rid of the Windows Mail in Internet Explorer.

  I tried to change my default email address in IE from my old Cableone address to my new address Qwest.  I followed the steps on the Web site of Qwest, but now my emails are transferred to Windows Mail and remove from Qwest.

  How can I make my default email address Qwest and get rid of the Windows Mail?
  If you want to use Webmail and not Windows Mail, an e-mail client, just remove the Windows Mail account in tools | Accounts.

• Impossible to access the account, the message says: "you cannot access your account because your parent has blocked it.»

  Changed the title: I opened an account and set up parental controls. It is impossible to access that account the message said "you cannot access your account because your parent has blocked it."

  I opened an account and set up parental controls. It is impossible to access that account the message said "you cannot access your account because your parent has blocked it."

  Hello Nimaakhaven,

  The best place to ask your question of Windows Live is inside Windows Live help forums. Experts specialize in all things, Windows Live, and would be delighted to help you with your questions. Please choose a product below to be redirected to the appropriate community:

   

  Windows Live Mail

  Windows Live Hotmail

  Windows Live Messenger

  Looking for a different product to Windows Live? Visit the home page Windows Live Help for the complete list of Windows Live forums to www.windowslivehelp.com.

• How can I stop my windows mail as my default email address?

  How can I stop my windows mail as my default email address?

  you would have set up an e-mail account in Windows Mail if you have a default e-mail account in

  BigPond is an ISP (internet Service Provider) providing Internet connections

  They also give you an e-mail address by default when you register with them

  Look in Windows Mail and remove account

  Add or remove a Windows Mail account

  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-remove-a-Windows-mail-account

• Access violation at address 74F735D1 in module "OLEACC.dll". Read of address 00000048

  Original title messages: error

  Can you please help me fix this annoying message. I get several guests for her, and I don't know why.

  Access violation at address 74F735D1 in module "OLEACC.dll". Read of address 00000048

  Hi   Travis815,

  (1) when exactly you get this error message?

  (2) since when are you facing this problem?

  (3) remember you to make changes to the computer?

  Please quote the complete error message you receive.

  Method 1: Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps mentioned in the link below:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Method 2: Put the computer to boot and then check if the problem persists

  Follow step 1 in the link below,
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem.

  Continue with the remaining steps to pin-point on the third party service.
  After find you the program that is causing the problem, you will have to perhaps to update or install a newer version of the program, if you rarely use that you should consider uninstalling the software.

  Important: n ' forget not to put the computer to a normal startup follow step 7 in the link.

  Thanks and greetings

  Ajay K

  Microsoft Answers Support Engineer
  ***************************************************************************
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Default IP address does not work after resetting to factory default.

  Hello

  I have a problem with a HP LaserJet P2015 default IP address. If I unplug the LAN cable default IP is set.

  As soon as I plug back into the address does not work and if I print the summary page, now, there are whritten:

  IP address: Configuration (it does not stop to set up after waiting 1 hour it's still set up).

  and:

  Auto-IP: enabled

  I think that the Auto-IP (DHCP, probably) is the problem... but how do I turn it off?

  Thank you

  Jay

  Hello JayKM,

  Welcome to the Forums of HP Support!

  To get your question more exposure I suggest you post in the trade forums since it is a commercial product. You can do the Commercial LaserJet Forums.

  Support of your product page can be useful in the meantime: HP LaserJet P2015 printer

  I hope this helps!

• Question of ML6000 Web Client. "The library is busy. Impossible to access."

  Hello

  I hope that somone can help me in this case.

  We have ML6000 library running.

  Since today I can't like connect on ML6000 Web Client.

  I get the message:

  "The library is busy. Impossible to access."

  I checked the library doors. Library doors are closed.

  

  How can I solve this problem?

  Thanks for all proposals.

  There are a number of things that could cause something like this happens. The first thing that I would recommend would be to restart the ML6000 library and get tickets RAS on the ML.

• Cannot access memory at address 0 x 0 at start of thread for the connection to build...

  Here is my code,

  void AlertListPage::onOnCallClicked()
  {
      thread = new DownLoadThread();
      QThreadPool *pool = new QThreadPool();
      pool->start(thread,0);
  }
  

  class DownLoadThread: public QObject, public QRunnable {
      Q_OBJECT
  public:
      DownLoadThread();
      virtual ~DownLoadThread();
      virtual void run();
  ...
  ...
  }
  
  cpp...
  
  DownLoadThread::DownLoadThread() {
      // TODO Auto-generated constructor stub
  
  }
  
  DownLoadThread::~DownLoadThread() {
      // TODO Auto-generated destructor stub
      sta::out<<"test";
  }
  
  void DownLoadThread::run()
  {
  ...
  ...
  }
  

  I set the breakpoint at the line:

  pool->

  start at (wire, 0);

  and the first line within the Run() method.

  run once OOP-> start and before running, it rises can not access memory at address 0 x 0.

  I do not see where I put the object as null...

  Thank you.

  Do you need a thread pool and QRunnable? You can also use QThread-> http://qt-project.org/doc/qt-4.8/QThread.html

  You initialize QObject in constructor? It's not like so, cause your Builder does not need a QObject as a parent. Then maybe parent is set to NULL.