Index a signal from a TOC file by attribute

Hello

I need to search a waveform within a TOC file by its name attribute, then pull (if possible just) that the simple waveform for later processing. I have attached a diagram where I am now:

Data storage - filepath to open and pass its refnum

Read [Channel] data - by refnum spent and provide the channel refnums

Create a query Expression - creates a correct query

Run a query Expression - runs, but returns an array instead of a single channel refnum?

Reading data [Channel] - out: the TDM channels, although I have indexed just a 1st?

Can someone help me solve this problem?

Here is the situation of file - I saved more than 100 shaking the stepped table. Each of them has produced 4 files x TDMS I had converted to 4 x TDM files. For each test, I need to locate and remove 3 waveforms that are randomly inside these 3 corresponding TDMs and perform a treatment on them and save a new TOC 7 waveforms from the transformation. My only problem so far is to get out of these different waveforms of the PDM. Is it possible to get out alone - not complete chains of the PDM 3 sets? -This is to avoid memory problems.

Thanks in advance,

Hi golubovski,

I suspect that the problem is in the execution of the loop after the first close data For. The refnum channel array passed to the loop For must be invalid because they will be released by first data closely.

Can you please try to move the first narrow data somewhere after the loop For?

Hope this helps,

Mavis

Tags: NI Software

Similar Questions

  • When you create PDF from WORD 2010 files, can't do the TOC header as hyperlinks entries

    When you create PDF from WORD 2010 files, I can't have the TOC header as hyperlinks entries. I'm used to be able to do this in WORD 2003. I tried to create a PDF file in Acrobat by selecting file > create PDF > navigate to the WORD file > select three check boxes >

    Help them get the entries in TOC topic as hyperlinks?

    Try to do this from Word by using the Ribbon.

  • opening .toc files

    I can't open the .toc file I HAV downloaded. Ive tried chip register but my computer says that the component that you are trying use 2 is on an unavailable network resource, then said: a smart registry product installation package cannot b found and told me to try the package installation again using a valid copy of the installation package "Setup.msi", then I get a fatal error during installation screen , which is weird bcaz smart registry came with my computer, why would not valid?  And my anti-Viru spyware is protected.  My computer is brand new, so I know that nothing is outdated.  Need help please, I paid ten bucks 4 the .toc file.  The .toc file is a mod for a game online, I bought.

    This is a mod for Word of Warcraft?

    If so check out this link
    http://forums.worldofwarcraft.com/thread.html?TopicId=442927843

    Relevant article copied from this link.

    How do we install the AddOns?

    I downloaded an AddOn, but I don't know how it works in the game, help!
    I downloaded an AddOn, but it does not appear under the [AddOns] button in the character selection screen, help!

    -The FAQ at Invisionboard.fr has a nice walk step by step through on how to install AddOns. There are also a few images of the good ways and hard to install, as well as a checklist of the most common mistakes, in case you're having trouble. Check it out here: http://www.wowinterface.com/forums/faq.php?faq=install#faq_howto_install

    Example of screen of the files directory structure: http://www.wowinterface.com/storage/faq/correct.gif

    Um. This zip file I downloaded is not all folders... just a bunch of files. What should I do? Credit: Syllani

    -One of the files in the zip should have the extension .toc file (e.g., there should be a file with a name similar to NameOfTheMod.toc). Simply create a new folder under your Interface/AddOns/directory with the same name (NameOfTheMod), put all the files zipped into this new folder.

    If it's not Wow then what game you try to mod? Will basically be the same procedure. Just find which directory that the file is assumed to be the place for the match to see. You will not be able to 'Open' the normal with windows tools .toc file. If you are really eager to see what is in it that you need to do for the game modding community searches to find the tools to extract the contents of the mod .toc.

  • where can I get a video decoder for win xp media center so I can pick up a signal from TV

    I use to be able to pick up a signal from TV, but since a new reinstall of xp media center I can not get a signal - the message says that I need a video decoder, where can I get this article

    Hi davidwiddecombe,
     

    A codec is a software to compress or decompress a digital media file, such as a song or a video. Windows Media Player and other programs use codecs to play and create digital media files.

    A codec can consist of two components: an encoder and a decoder. The encoder performs the compression function (coding) and the decoder performs the decompression function (decoding). Some codecs include both components and some codecs only one of them.

    Use your favorite search engine and browse for such a program which is used to.
     

    Note: This response contains a reference to third party World Wide Web site. Microsoft provides this information as a convenience to you. Microsoft does not control these sites and no has not tested any software or information found on these sites; Therefore, Microsoft cannot make any approach to quality, security or the ability of a software or information that are there. There are the dangers inherent in the use of any software found on the Internet, and Microsoft cautions you to make sure that you completely understand the risk before retrieving any software from the Internet.

  • ePub creation - TOC FILE MISSING - questions with 7zip VS zip.exe

    Since this question is not really answered - that is to say, the same problems are produce I found elsewhere the ePub Script, I need to reup the question.

    Here's my biggest problem - when 7zip is selected BY RoboHelp to generate an ePub, it does not work.

    However, when RoboHelp tells me to select zip.exe in stahlforce.com/dev/zip.exe, it works fine.

    But there is no way for me to put the ZIP. EXE as the standard when I create an ePub and run the script - he immediately says TOC FILE MISSING as it does the file NCX (TOC) creation.

    Warnings:

    I always get an error.

    This occurs if the XML file generate is in the folder SSL project or not, no matter whether on a C drive or a drive E (or a network drive, USB stick, etc etc etc)

    If I manage to, by some MIRACLE, he can use zip.exe instead, it will compile happily with a table of contents.

    My system path already has System32 inside. No need to change it.

    System: Windows 7 Professional 64-bit

    7zip: latest version

    RoboHelp: 9.0.2 in ATCS3

    So far, I have:

    1 removed all spaces in my project name and outputs ePub by this post: http://forums.adobe.com/message/3155109#3155109

    2. followed the instructions of Praful letter after having contacted him to find out exactly how we're going about adding the system32 in path variables.

    3. run the generator fifty - nine times.

    Out of those fifty - nine times, I also have:

    A. downloaded 32 bit 7zip used as the source Zip and it craps the bed with a missing TOC error message. No go.

    B. downloaded 64-bit 7zip used as the source Zip and it craps the bed with a missing TOC error message. No go.

    Zip.exe c. downloaded as requested, used as the source Zip, HOORAY! It works!

    D. try to replicate, it goes back to 7zip and craps the bed. KHAAAAAAAAAAAN!

    Now I did this on my C (SSD) drive and my drive E (a regular storage drive) and used RoboHelp in two places, that on both the C and the E drive all is content (project, file, exit) at the same place. I did it on systems clean and 'dirty' and all. UNIQUE. TIME. RoboHelp blithely informs me that there is no TOC file.

    When this happens, it's ALWAYS when it tells me to use 7zip instead of, let's say "zip.exe.

    robohelp_epubbedcrapping.png

    Like this.

    My default ePub reader has been Adobe Digital Editions. She always does.

    I changed the default ePub for Sony Reader Library drive. She always does.

    I changed the default ePub to gauge reader. SHE IS ALWAYS.

    I did it with drive C as the unique environment system.

    I did it with the drive E as the unique environment system.

    I even installed RoboHelp on a computer with a single hard drive and did nothing, but generate this file.

    When RoboHelp wonder for zip.exe location, it compiles BEAUTIFULLY.

    But then he goes immediately to 7zip and craps the bed.

    Now, when I say "There is always this", I mean that I returned to all the variables from that moment. So, when you get to 'Drive C as the system of unique environment' which means all that above, I did with this condition.

    So to answer the question in abeyance, "What is your system?" it's in Windows 7 Professional 64 bit running.

    Yes, I tried the path of Praful system variable.

    Yes, I tried clean installs.

    Yes, I tried it on a solo record.

    Yes, I've tried it on a clean build of Win7.

    Yes, I tried all of this.

    He's still crapping the bed when it comes to the path of TOC disappeared.

    As some authors have said, there no errors in the log. There are no files not referenced, no oddity in the project naming conventions, nothing.

    But if she goes to 7zip, it craps the bed.

    If she stays with zip.exe, that's fine.

    So, what else can you guys help out here with? This isn't a terribly difficult thing - to compile an ePub is really not that difficult. But what I need to know is that could possibly do to solve this problem?

    Is there a setting to make the zip extension zip.exe in ONLY in the script? Which seems to work, but RoboHelp like return to 7zip.

    Like others, I have followed these instructions very closely, but it seems to always be a "oh yes, make sure that..." "that comes with RoboHelp who never gets bound upward in the manuals.

    So, what's the next "Oh yes, make sure that '? I would like to know because frankly, at this point RoboHelp made less useful work the creator of ePub $40 program I bought of frustration with the process of generation of ePub.

    Hi, 7zip is the old method of zipping toward the top of the epub. When you install 902, a new script is provided, but you need to make it accessible by hand. Maybe this new version allows to your problems.

    See the 9.0.2. README:

    output ePub

    After you install the hotfix, copy the script to update ePub Generator.jsx of [InstallDir] / RoboHTML/settings presets/scripts/in the following location:

    • Windows XP: [USER] / Application Data/Adobe/RoboHTML/9.00/Scripts/Sample Scripts.
    • Windows 7: [USER]/AppData/Roaming/Adobe/RoboHTML/9.00/Scripts/Sample Scripts /]

    A little bit of guessing here: are there special characters (e, to, etc.) in the name of your project? The output XML really should OCD assigned for output?

    Would it not possible to share the project so that we can take a look?

    Take a bow

    Willam

  • How can I restore signal from my Mac Pro to my Viewsonic monitor, connected by VGA?

    I have a Pro Mac OSX version 10.7.5 running. Trendy top is a monitor 24 inch Viewsonic, the only monitor connected. Last week, everything was fine. I stopped him all night and the next morning, when I tried to start, there was no signal from the Mac to the screen.

    The screen displays a 'No Signal' message.

    I checked the entry on the monitor, and it is correctly set to PC.

    The computer starts normally. I can hear him do his thing.

    The monitor starts up normally. No flashing or spots.

    I tried restart, disconnect the monitor from the computer, just stop and unplug it, then reconnected. I tried to plug the old monitor (using VGA connection) and start again, with the same result.

    I tried to recall the NVRAM (found the instructions on this site) and it made no difference.

    It would be appropriate to get a HDMI cable to connect the?

    It seems to me that if the computer does not recognize the monitor, try another cable wouldn't make any difference, but I'm really an 'end user' at this stage and would appreciate any advice.

    Thank you!

    Try resetting the SMC

    Reset the management system (SCM) controller on your Mac - Apple Support

    The VGA input and cable works with another computer/device?

    The port of exit on the Mac works with another monitor?

    What model Mac pro?

    What video card is installed in the Mac?

    What output port are you helping?

    Maybe the video card has failed. If yo have an old Mac Pro with an original which is likely to card

  • My p6000 resumes signal from the wireless router. He has worked for months, has left, any help?

    HP Pavilion p6631p

    Windows 7

    I have a slightly new wireless router and the PC is always connected like this, but in the last days he will not pick up any signal from my router or our hot spots of our my touch 4g cell phone.

    It will not work so hard cable...

    Occasionally, he'll go get a weak signal, but I think there out crapped on me, anyone else having this problem?

    Warranty has expired 3 weeks ago! Pissed! I think they do it on purpose.

    If the antenna wire is not damaged or not connected, I would consider looking at an ASUS, Linksys, D-Link or Netgear PCIe x 1 or wireless USB adapter to replace the original one. Here is a selection of Newegg.

  • I'm doing a script that takes a list of e-mail from a text file and then allow me to select a save as a string. I found some ways to get the path of the file, but I'm in check by pulling the list

    I found some ways to get the path of the file, but I am defeated by pulling the list from that. the function of the path get gives me the path as "Macintosh Users:: Documents: extractedb.txt (myUsername).

    What I can't understand is how to get a dialog box to display a list that represents the content in the text file, I need to change the contents of the text file, I need the box to show me what I chose and I want to save my selection as a single string.
    e '.

    example of extractedb.txt information:

    [email protected]

    [email protected]

    [email protected]

    * has a random number of emails as well *.

    I want this is to pull those emails from the text file and turn them into a list so I can get to be a selection in my dialog box.

    Any help would be great = D

    Assuming you have a text file with your example e-mail addresses, the following AppleScript will read this file in a list (mf_List) and then use this list as input to choose among the list. Because multiple selection is allowed (control button), the output is sent to a list (sel_addr). We check if the Cancel button was pressed by testing for false and if this condition is met, we the script error.  Based on a single or multiple list item content of the list, display accordingly.

    game of mf to ((path to the folder as text) & "mail_list.txt")

    the value mf_List to {}

    the value sel_addr to {}

    the value mf_List to paragraphs of (read file mf)

    the value sel_addr to (choose from the list mf_List with title ¬

    ('Mail list' with multiple selections allowed without empty selection allowed)

    If sel_addr is equal to false then

    Error number-128

    return

    end if

    If length of sel_addr is equal to 1 then

    sel_addr display dialog box as text

    on the other

    the value Point to the text of TID to AppleScript delimiters

    the value Point text in AppleScript return delimiters

    display the dialog box elements of sel_addr in the text

    the value Text of point AppleScript delimiters to TID

    end if

    return

  • How can I restore my bookmarks from an HTML file?

    I just installed Ubuntu 11.04, and I want to restore my bookmarks from an HTML file.

    This used to be accessible through the "bookmarks - > organize bookmarks ' menu item 'Organize bookmarks' no longer exists so I'm stuck.

    This help system seems to think that there is, however, so please note that on my system, it isn't. I suspect that hundreds, thousands or even millions of new users of Ubuntu 11.04 will have exactly the same problem.

    I don't think that users will be able to help with this one, unless someone knows how to restore the menu item 'Organize Favorites '. It is the only one that will do what I want and so there is no point recommending "Show all bookmarks" as a solution. It does not work.

    Finally, persuade this system that I don't really have a new problem that are not addressed in the FAQ section has been a very irritating experience. I wonder if Chrome will know what to do with my file "bookmarks.html"?

    "Bookmarks > organize bookmarks ' has been renamed to"show all bookmarks"in Firefox 4.

    If the menu bar is hidden, and then click the Firefox button to open the Firefox menu and click the bookmarks entry or click "Show all bookmarks" to open the library.

  • Toshiba 42Z3030D TV not receive signals from the remote control

    I can't use any (Toshiba or the distance from Sky TV) remote on my TV.

    Everything works on the TV when I use the buttons on the side of the TV but the TV does not seem to receive all signals from remote control.

    I changed the batteries in the remotes, and it still does not work.

    Can anyone help please?

    Model: Toshiba 42Z3030D TV

    T couldn't be possible that your TV remote is malfunctioning?
    Maybe you need to replace.

  • No Signal from my hp probook 4320 s on TV with the HDMI cable

    Hello, I have a hp probook i3 4320 s, and recently I have buy a new lg led tv, my problem is my new TV can not get the signal from my laptop, please help me, thanks

    Hmmm, if the screen is black no don't say no signal?
    This means that it is signal to the TV, but don't not why I cannot display graphics.

    Refer to:

    http://Windows.Microsoft.com/en-CA/Windows7/automatically-get-recommended-drivers-and-updates-for-your-hardware

    Then see (in order to please):

    https://sites.Google.com/a/mhelp4u.com/mhelp4u-com/Windows/Windows-7/How-to-scan-for-hardware-changes-using-Device-Manager-in-Windows-7

  • How to extract the text from corrupted pages file

    Really appreciate if someone of you knows a way to extract text from a page files of 9 MB that contains text and images and which does not:

    Error message: file format not valid.

    Change the type of file and opening in various programs (Word, Acrobat, Google doc converter) but nothing I've tried will open it.

    I have a backup at home, but am away for several weeks and done a lot of work on this file since the last backup.

    I hope there is a solution! Thank you

    JR

    If it is in fact a v5 Pages document, and it will not open in preview, or open in v5 Pages while holding the SHIFT key, then you're done. The inner content in Pages v5 is in a format that is illegible, indecipherable, scrambled anything able to read except Pages v5.

    If it's a v5.5.2 Pages or a later version of the document, then it is by default in a single file format (file zip compressed/renamed), and no version of Pages thru v5.2.2 on Mavericks v5 was designed to play a single file format documents that are not original Pages ' 09. If it is a document Pages from Yosemite or El Capitan, you will need the v5.5.3 Pages or later to change the type of file to the package format - which can be read by v5 + Pages on the Mavericks.

    If it is a Pages ' 09 document, there is a good possibility that your attempt to open/edit/etc this document with all of the people mentioned applications has damaged the document permanently. Try the preview or the free LibreOffice (v5 or later) which can open documents file format only (not the package files) of Pages ' 09 very simple, sometimes with pictures. No warranty if.

  • 4540 s: no Signal from my computer to the TV with a HDMI cable

    No Signal from my computer to the TV with an HDMI cable. What can I do? Windows is up to date! My laptop is Hp4540s, Enterprise 64-bit windows 10

    Hi!, attilak:

    Welcome to Forum!

    (1) try, update of the graphics drivers, of... http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=5229457&swLangOid=8&swEnvOid=4192

    (2) try to change, by others, the HDMI cable.

  • There is a possibility to run Labview projects or to set them off from a batch file or if the exist and the ability to control labview or run it from an external application?

    Hi, I m a bit new in LabVIEW and I'd like to ask a few questions...

    -There is a possibility to run Labview projects or to set them off from a batch file or if the exist and the ability to control labview or run it from an external application?

    -One API PI or raspberry beaglebone exists for LabVIEW?

    -Power supply Wich can recommend you control with LabVIEW? (some chip solution witn 0 - 30v / 0 - 3A DC)

    Thank you very much for your advice!

    Best regards

    Elena

    Elena,

    I know raspberry, so no comment on that.

    For the rest:

    -Do you want to create tools for developers? If so, we must look in the API of project VI and VI server. If this isn't the case, please compile your application LV as executable and call this one using a batch file.

    -LV prefer specific supplies. LV is a programming language. There are several power supply providers (including OR) which provide directly the LV API for their power supplies. So, essentially, the approach is:

    1. choose food that serves your needs.

    2. check if the power supply has a standard interface for programming (such as Ethernet, GPIB, or if the power supply is PXI, is already providing a programming interface!)

    3. check if the LV API (so-called "instrument driver") is available for the device. In the case of a PXI system, get you a device driver (for example NI DCPower).

    4. check if the LV samples are available (for example in the Finder for example LV once you have installed the driver).

    Norbert

  • How to write data from the INI file for the control of the ring

    Hai,

    I need to write the data read from the INI file to a control of the RING. Doing this operation using variants I get the error.

    I will be happy if someone help me. I have attached the file special INI and VI.


Maybe you are looking for