??? Insert the "NI LabVIEW Run-Time Engine 7.1.1.

OK everyone, I'm "dead in the water" when launch LabVIEW 2014 SP1 after a long night of installing updates to Developer Suite 2014 DS2 SRL 2015 DS1 SRL

Search Forum has this old thread

http://forums.NI.com/T5/LabVIEW/error-1334-in-LabVIEW-run-time-engine-7-1-1-Setup-when-launching/TD-...

Since 2008

NOTE: at least its looking for a CD ROM is not a floppy disk!

Hooray!

I've recovered from that.  And Yes, I'll tell you how that you can do it yourself if this happens to you:

From the control panel select programs and features, then National Instruments software.

Scroll to "LabVIEW Run - Time Engine 7.1.1" and select Repair

You will need the following:

  • Device drivers OR August 2014
  • C:\ProgramData\National Instruments\Update Service\Installers\NI_20150630_0736
  • NEITHER Developer Suite 2015 Encarta software
  • Patience

Tags: NI Software

Similar Questions

  • Can I run two separate versions of the LabVIEW Run - Time Engine on a PC?

    Hello, I am curious to know if anyone knew if it is possible to install and use the two separate versions of the LabVIEW Run-Time Engine on a PC?  I have currently 2009 runtime engine installed on a machine, and I wanted to install the runtime for 2011 as well. I know that you can run two separate versions of the LabVIEW program on the same machine, but what about the Run-Time Engine?

    Thank you!

    No problem at all. I currently have the engines of execution for 8.2, 8.6, 2009, 2010 and 2011 on my computer. Multiples are no problem at all. Go ahead and load.

    Rob

  • Unable to locate labview run time engine

    Hi all

    I have a problem while trying to run a simple labview software on a Tablet PC.

    My development machine is under win 7 64 bit with labview 2010 sp1 10.0.1

    My computer is a win 7 32 bit based tablet.

    I installed labview runtime engine TEN 2011 standard 32-bit sp1 but I get the following text: «unable to locate labview run-time engine...» "

    I tried to install sp1 64-bit of the 2011 standard RTE because one of the items suggested, but windows is not allowing to install 64-bit applications...

    Should which version of the Runtime I install!

    You did not say, but I'm assuming that you are using LabVIEW 2010 sp1 32 bit to develop and build the application.

    You can include the 2010 sp1 Runtime when you build the Setup program, or you can download it (here) and install it separately.

    (The runtime version must match the development system, so time to run from 2011 will not work. Even the 2010 (non - SP1) could cause problems)

    Kobi Kalif wrote:

    I tried to install sp1 64-bit of the 2011 standard RTE because one of the items suggested, but windows is not allowing to install 64-bit applications...

    Can you tell me what position suggested to install an operating time of the wrong version of 64-bit. That makes no sense at all! Please provide a link.

    (You can only install the runtime on a 64 bit OS, 64-bit, and he will agree only if the application has been developed in 64-bit LabVIEW to the same version.)

  • LabView Run - Time Engine 2009 installation failure

    Hello

    I have problem to install Labview Run - Time Engine 2009.

    This error occurs:

    Die Installation von NI VC2008MSMs x 86 ist auf Grund of the following Fehlers fehlgeschlagen.

    Auf den Windows-Installationsdienst konnte nicht rarely werden.

    Die kann occurrence, wenn Sie Windows im abgesicherten Modus implement oder der

    Windows-install extension installed ist nicht. Wenden Sie sich an den Support, um Hilfe zu receive.

    (The installation of the NC is VC2008MSMs x 86 has failed due to the following error.

    The Windows Installer Service could not be accessed. That may occur when you run

    Windows in safe mode or Windows Installer is not correctly installed.

    Contact your support team.)

    I tried to reinstall and reregistrate program windows installation, I tried to upgrade the installer from windows to version 4.5

    I installed Microsoft Visual C++ 2008 Redistributable-x 86.

    IM runing Windows XP Service Pack 3

    (Microsoft Windows Version 5.1 (Build 2600.xpsp_sp3_gdr.100427 - 1636_ Service Pack 3))

    I have no problem installing other programs, for example, can I install runtime labview 7.1.1.

    So my question is:

    How do to solve this problem, how can I make a Labview Run-Time Engine 2009 installation on this computer which gives me the error described at the beginning?

    Best regards

    Simon

    Now I have solved my problem.

    The solution was to raise and to build my code in Labview 2010.

    But the question of the installation contains yet to install LabView Run-Time Engine 2009.

    I don't think it's associated Windows Installer, because I can install everything on my computer in addition to LabView Run-Time Engine 2009.

    I can even install LabView Run - Time Engine 7.1.1 and LabView Run-Time Engine 2010.

    So, my solution was to jump using LabView 2009 and install LabView 2010.

    Best regards

    Simon

  • Impossible to uninstall LabVIEW Run - time Engine 2013

    I have a PC that had both the LabVIEW Run-Time Engine installed 2013 and 2013 LabVIEW development environment.  I uninstalled the 2013 LabVIEW development environment, and now the executable files will not work.  They say that the Run-Time of 2013 is not installed.  However, execution 2013 is listed in MAX.  It does not appear in the list of available software to uninstall, so I can't uninstall and reinstall either.  When I try to run the installer from the runtime of 2013, it is said that the runtime is already installed.  It seems that I am stuck with a corrupted installation of Run-Time?  Is there anyway to remove completely the execution so I can reinstall it properly?

    Thank you

    I thought about it.  I managed to uninstall the runtime engine by following the instructions here: http://digital.ni.com/public.nsf/allkb/F4B8D92A304E4A7B862577460072002F

  • LabVIEW: error building Installer 2011SP1: LabVIEW Run-Time Engine 2013 missing 3 dependencies?

    I'm having a problem of construction of an installer in 2011SP1 of LabVIEW.

    It has been a while since I tried to build an installer but it used to work properly and building executables still works fine.

    Now when I try to compile the installer, I get "generation failed."

    The possible reasons: error generating preview for my 3.1.7 Application.

    Details:

    Visit the Request Support page at ni.com/ask to learn more about resolving this problem. Use the following information as a reference:
    
    CDK_Build_Invoke.vi.ProxyCaller >> CDK_Build_Invoke.vi >> CDK_Engine_Main.vi >> IB_MSI.lvclass:Build.vi >> IB_MSI.lvclass:Engine_InitializeDistribution.vi >> IB_MSI.lvclass:Report_Preview_Error.vi >> IB_Source_Container.lvclass:Report_Preview_Error.vi
    
    Loading product deployment information*** WARNING ***NI LabVIEW Run-Time Engine 2013 is missing 3 dependencies. This product, or other products that depend upon NI LabVIEW Run-Time Engine 2013, may not function properly while the dependencies are missing.  Visit ni.com/info and enter the Info Code "" for more information.
    
    ***************** Error: An internal error occurred for which the cause is unknown. (Error code -41)***************** Error Details:Error in MDF API function: _MDFCommon_GetNextLogMessageError in MDF::GetInstance - MDF static instance is not initialized!*** End Error Report**************
    
    Loading product deployment information*** WARNING ***NI LabVIEW Run-Time Engine 2013 is missing 3 dependencies. This product, or other products that depend upon NI LabVIEW Run-Time Engine 2013, may not function properly while the dependencies are missing.  Visit ni.com/info and enter the Info Code "" for more information.
    

    The really strange thing is that I'm using LabVIEW 2011SP1, I don't even have installed LabVIEW 2013, not even the runtime.

    Where is the problem? Why is he still complain about LabVIEW 2013? Anyone seen this before?

    Troy,

    This behavior makes me assume that you updated certain components from the past. There are drivers of OR who use LV components (e.g., AFAIK the DAQmx of Test panels).

    Update you things? If Yes, why don't you LV 2013 RTE installed as it would be necessary for full functionality of the driver?

    Norbert

  • VI LabVIEW Run-Time Engine adapter server configuration

    I want to connect to use the desktop execution trace toolkit to debug LabVIEW code modules using the adapter runtime TestStand.  How can I configure Server VI using LabVIEW VI in the LabVIEW Run-Time for TestStand engine adapter?

    Have you tried to create seqedit.ini (really .ini) or even in the directory of the executable that you use for the TestStand UI?

    -Doug

  • Error occurred during deployment of TS and the LabVIEW run-time engine only

    Hi all
    I'm new to Teststand deployment.
    Now, I want to deploy a program to clean install with SP1 2012 Teststand engine, LabVIEW 2012 SP1 Runtime, VISA 5.2 DURATION.
    My file in the sequence is empty. (In fact with a label only)
    But I got "Internal error code - 12 making an installer... ", and" MSI error code: 110 ".
    Attachment is the newspaper.
    Any Suggestion? Thank you.

    Thanks to KateB.

    Now I find out why an error occurred.

    I installed LabVIEW 2012 first, then crushed with LV 2012 SP1 but no uninstall.

    I think it makes Teststand to be comfused or maybe something conflict.

    Now I install LV 2012 or LV 2012 SP1 only. It works very well.

  • Error 1335 during installation of NI LABVIEW Run time engine 2009

    Hello

    When installing Labview 2009, I get the following error.

    Error 1335: The file 'mib100.cab' required for the installation is damaged and cannot be used. This may indicate a network error, error reading from the CD-ROM, or a problem with this package.

    I tried to install the software using 2 different CD-ROMs, and hard drive. I also uninstalled software OR previous and tried to install Labview again.

    Screenshot of error during the installation of the hard disk is attached.

    Thanks in advance,

    Hyacinth D

    The installation was successful, after replacing the DVD drive.

    Thank you!

    Corinne

  • Improved LabVIEW 8 to 2013 and VI asked now to find the installation package for Run-Time Engine 7.0

    I recently installed LabVIEW 2013 on a computer (running Windows XP 32-bit).  The machine has also of LabVIEW 8 is installed, which is what I used before the upgrade.  I opened a VI has been created in LV8 and then saved it and all its subVIs in LV2013.  Now when I open the VI in LV2013 and try to run it, a window opens asking me to find the installation package 'lvruntimeeng.msi' for LabVIEW Run-Time Engine 7.0.  If I cancel this dialog box, and the subsequent message, indicating that the installion files were not, the VI appears (at least of the initial inspection) to function normally.

    I have closed LabVIEW, downloaded Run-Time Engine 7.0 on the site of NOR and tried to install it, but I received a message saying that it is already installed (as I had suspected).  How can I determine what part of the VI and/or its subVIs tries to make use of Run-Time Engine 7.0?  If not, how can I get LabVIEW to use instead the Run-Time Engine 2013 that was installed when I upgraded to LabVIEW 2013?

    Bob_Schor wrote:

    You run your VI of a project?  If so, you can watch the dependencies and get an idea of what live "in charge", you might have.  There may be "something old" in your code in LabVIEW 8, which was replaced in 2013, but ' plane still around "-If you can identify it, you can probably replace it with its"more modern"equivalent

    If you do not have the VI in a project, you can simply open LabVIEW, create a blank project and add your first level VI.  If all of your relevant screws are in a single folder, add the entire folder.  Now look in the dependencies.

    BS

    Yes, I run the VI from within a project of LV.  After some more research in the knowledge base OR I could solve the problem by using the following procedure:

    1. use the measurement and Automation Explorer to uninstall Run-Time Engine 7.0

    2. restart the PC

    3. open the project, close the project by choosing "save all".

    4. restart the PC

    5 reinstall the Run-Time Engine 7.0 using a file downloaded from ni.com

    6. restart the PC

    7. open the project, close the project by choosing "save all".

    8. open the project and run the VI.  No more messages on LabVIEW, trying to find the Run-Time Engine 7.0.

  • Where the last installation program LV2010 Run-Time Engine?

    Sorry for this absurd question, but after a half hour of roaming the site I can't find an installer LV2010 RTE.

    Would it not be this difficult?

    Could someone tell me please in the right direction?

    Thanks in advance!

    http://lmgtfy.com/?q=+LV2010+RTE+Installer

    Sorry, but I love this site sometimes.  I found the search function OR be so difficult.

    Or click on Support Services & > NOR drivers > software > LabVIEW Run - time Engine

  • NI-VISA run-time engine

    When 'building' a LabVIEW program containing NI-VISA under VI (for example to connect with USB), I had problems to get the code 'built' to find my devices NOR VISA, even if the NI VISA's USB drivers are correctly installed on the computer 'target'.

    (The code 'built' will run if the target machine has an installation of LabVIEW to this topic, including NI-VISA)

    -The NI-VISA run-time engine will automatically appear in the 'Build' (because of the Sub - NI VISA VI), or should I specify myself - and how?

    Thank you. Peter.

    Create an installer as you did the executable version.  The installation program will be for the executable, not for the original project.

    What version of LabVIEW are you using?

  • VISA writing differs between TS and LV Run - Time Engine development agencies

    Hi all

    I made a request on LabVIEW to test the BERs (Bit error rate), and I used the Write VISA between two COM ports to Exchange data.

    Everything works great using just of LabVIEW.

    Later, I used TestStand to call my application (VI). Adapters of LabVIEW TestStand have been set by default on the development system , and everything works OK!

    Finally, I had to disable the development system and to define the types of adapters LabVIEW of TestStand for LabVIEW Run-Time Engine and I noticed that the speed of the exchange of data between two COM ports significantly decreased.

    The only difference was the speed... because all data (changed slowly in this case) happened correctly on the other COM port too.

    The symptom was the same that decrease baud rate... but baud rate and all other configurations remained the same. The only difference was the change between the development system for the runtime to notice this reduced speed between the data exchanged using VISA Write.

    All the solutions for this?

    Thanks in advance

    João

    Hi all!

    I'm sorry, I forgot to reply to this thread...

    Solution was change the way VISA WRITE of "asynchronous" to "synchronous" to book a thread just to WRITE visa.

    The problem here was something like this (?): TestStand used all available threads and when we wanted to WRITE of VISA, the thread has been busy and VISA would wait until the wire emerges. After changing to syncrhonous, there was a thread dedicated to this process (?).

    Now, everything works the same using LabVIEW Run-Time Engine or system deployment.

    Thanks for the help Chris and Norbert :-)

    João

  • License OR VISION Run-Time Engine

    Hello

    I send you this question because despite the number of doc that I could find in relation to my question, I have not had a clear answer to my pb:

    I have an application that has been developed with LV 8.2.1 using NI IMAQ 3.7 from functions. (Very briefly the program acquires images from a camera, performs simple operations on images and saves the results of these operations, so other images).

    I would like to know what are the licenses I need to purchase pour installer of the compiled version of my prog on client pc (which does not have LV). (I know I'll have to buy for each client PC licensed IMAQ 3.7 but regarding the treatment of these images can I just no VISION Run - Time Engine 8.2.1 which seems to me is free in the same way that NEITHER LABVIEW Run-Time Engine 8.2.1)

    Pour your response thanks in advance that I help him nothing I hope to see more clearly between the IMAQ vision, vision performance, VISA Run-time...

    Normal 0 21 false false false FR X-NONE X-NONE MicrosoftInternetExplorer4 / * Style Definitions * / table. MsoNormalTable {mso-style-name : « Tableau Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-marge-haut : 0 cm ; mso-para-marge-droit : 0 cm ; mso-para-marge-bas : 10.0pt ; mso-para-marge-gauche : 0 cm ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

    Hello fabrice91,

    The Runtime of NOR-VISION is available to download for free, however during the installation you have to activate it. When you create an executable LabVIEW AAFC is not automatically run time engine, this is why you need to create an installer that will contain the TENS of LabVIEW and NI of VISION. If you run the executable on the development computer it is normal that your application turns car you have all the necessary Runtime on this post. However if you try to run your application on a machine where there is no software OR your executable will not have to work and that's your Installer. Pour the know National Instruments programs installed on a PC you have several opportunities either through Measurement & Automation Explorer either start > Control Panel > Add/Remove Programs > software from National Instruments.

  • Run time engine Web Service

    Hello gentlemen, everybody knows why I can't access VI (*.exe) on the remote PC. On remote PC has been installed only standard 8.6 Run Time Engine. Do I need to install additional like OR LabVIEW Run - Time Engine Web Server parts or / and Server Web LV? And is it possible to communicate through this using RTE on both sites?


Maybe you are looking for