Install Windows 8 on Windows 8.1 pro

Similar Questions

• Install windows on mac pro (early 2008) in other SSDS with RAID card

  Guys, good evening to all the same time.

  I get out of this crazy short, I ask humbly help.

  I explain my problem:

  I have a Mac Pro (early 2008), with RAID CARD MEDIA

  He does not then I "gave" to my mother who must use windows for work.

  I'm out all 4 disks in RAID installed and mounted 2 - SSD OCZ Agility 256 GB.

  one of them is installed OSX Yosemite. on the other hand, I want to install WINDOWS.

  and here the problems begin:

  When I insert the win8.1 to proceed installation standard dvd (EFI not talked since the beginning of 2008), I get, when I have to decide on which disk to install and format windows, does not reveal the installed drives

  After 2 days of tweaking, I was able to understand that this is a problem due to the RAID card installed, I also read that you just remove it and connect the SSD in one of the two doors empty ODDsata (and not in the 4 planned the raid card slots)

  but still does not see the attached HDD / SSD, so keep trying and I think it's a driver problem and I need to install the AHCI driver, now, I'm pretty Nerd, but I still can't get.

  Someone could want explain step by step what I need to do to install this * win on MacPro 8.1 designed for RAID card?

  Thank you so much in advance.

  A welcome message

  Ruggero

  If you remove the card RAID Apple on the Mac, you MUST connect the iPass cable on its location on the motherboard, or all four bays are unusable:

  

  .

• Cannot install windows on Satellite Pro A40

  Hi I read through all the posts and I can't seem to find an answer.

  My problem is that...

  I tried to install windows from a full version and when I want to install windows on a partition it fails. If I try to delete the partition, it fails. If I use the recovery discs - Option 1 not entered completely load - looks like Gdisk? error and then a ghost. Option 2 loads but when I go again to install fails.

  I can't find an option in the bios to prevent disk access - as a protection against boot viruses. the key under the keyboard, I tried in both positions.

  I removed the battery to see if it is a power problem.

  I tried using the options of recovery in win xp - but cannot access the drive

  The really strange thing is over the option of recovery disks 2 - the size of the disk is larger than the actual size of about 1/3?

  The system initially went down while it is connected to the internet - the only option I can thing of is a power surge came down the line and has damaged the motherboard or hard drive. As it happened to a desktop system - blew 3 modems and a UPS before we have located the problem.

  Help!

  Hello

  tried to check and format the drive with an external tool? I'll give you a suggestion: try the "ultimate boot cd" which has many tools also some tools for the maintenance of hard drives.

  You can get the picture here: http://www.ultimatebootcd.com/

  Just burn it to a CD, boot and choose the tool for your hard drive to check it out and repartition it.

  It could be that useful...

  Welcome them

• Question to install Windows 8.1 Pro on 2014 iMac, 21.5 "?

  I was able to use bootcamp to create a windows bootable flash drive. I was able to create a 160 GB partition to install Windows. I could reboot and start Windows to install. When he arrives at the section of the partition, disk 0 partition 4: BOOTCAMP, this is what these instructions indicate that you choose, and format. I clicked on the format, but as soon as label 'BOOTCAMP' disappeared, I had an error message saying that Windows cannot install because the GPT partition style? Can someone please help me with this, and more if you have me delete the partition using boot camp and create a partition with disk utility, I will need still more detailed instructions. Instructions on how to format this partition so that Windows can be installed on it. I tried disc utility Lane, but he gave me the same error of TPG and wouldn't let me even click on format. Also I couldn't format options advanced as I read people talk in other forums. I would appreciate your help, please and thank you!

  I know he said Mavericks, but I've updated to El Capitan and have everything updated before doing all this!

• just installed Windows XP SP2 Pro and get error: 0x8024000A in Windows Update?

  I get the error: 0x8024000A in Windows Update, and I'm under that Windows XP SP2 Pro just recently reinstalled today.

  Can someone help me with this?

  im not the smartest on the block, but I reinstalled as xpsp2 windows update did the same thing for me I sat worrying two days with this stupid thing, they me windows update won't let me download with less than sp3 will be unless your computer is about to receive the sp3 icouldnt it can illuminate only after downloading sp3 so I had to reinstall again but this time I made sure my system date was correct - all my captures has been eliminated - an i downloaded the new window dowload agent 30 x 86 - a wala it worked hope I have to read these post for two days, I don't know how madning it can be

• Cannot install windows 8.1 pro (error 0 x 101-0 x 4017)!

  I tried to install win pro 8.1 on my desk and his shows "error 0 x 101-0 x 4017" and the installation fails after the entire installation is filled.

  Hello New,

  Thank you for the update.

  You try to install updates at a time and see if it works. For example: install 10 updates every time and see if it works.

  If this does not help then, try to run the Windows Update Troubleshooter. Follow the link below to do the same.

  Description of the Windows Update troubleshooting tool

  https://Support2.Microsoft.com/kb/2714434?WA=wsignin1.0

  I hope this helps. Otherwise, feel free to write us again for more assistance, and we will be happy to help you come.

• Install Windows Pro 64 bit on HP Pavilion 8.1 X 2 10-j033au

  Hello

  I need to know if this able to charge Tablet install Windows 8.1 Pro 64 bit?

  Currently, it is pre-installed with Windows 8.1with Bing 32bits.

  I wasn't able to boot from USB for it. The USB key, I had can start on any PC or laptop. With the exception of this particular Tablet.

  I hope that this tablet is not related to this OS only.

  Any help will be appreciated.

  Thank you.

  I checked the support drivers for this product and seems that only Windows 8.1 and recovery disc 32-bit drivers are available. 64-bit is not supported on this unit.

  http://support.HP.com/us-en/drivers/selfservice/HP-Pavilion-10-K000-X2-detachable-PC/7439381/model/7468031#Z7_3054ICK0KGTE30AQO5O3KA30R1

• HP probook 450 g2 i7: drivers windows 8.1 with windows 8.1 Pro compatibility

  I intend to install windows 8.1 Pro on "HP probook 450 G2 I7" but when I went to download the drivers, I have not found windows 8.1 Pro listed in the operating system... I found windows 8.1 so I wonder if 8.1 windows drivers can be installed on a windows 8.1 Pro?
  Thanks in advance!

  Mounirian

  Hello;

  Let me welcome you on the HP forums!

  I read your post on Win8.1 drivers and wanted to help.

  For Win8x, the Home and Pro versions only see different features that come with each of two Windows versions.

  The drivers for all versions of Win8.1 are the same.

  Good luck

  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!

  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• Validity Sensor does not not in dv7t - 6 c 00 CTO Quad Edition using Windows 8.1 Pro 64-Bit

  Hello

  I have a Pavilion dv7 (dv7t - 6 c 00) CTO Quad Edition (product # A1L77AV) I can't get the validity fingerprint sensor to work after installing Windows 8.1 Pro 64-Bit from scratch.

  Windows 8 drivers that are available for this model do not seem to work. Other drivers Windows 8.1 available in the HP site do not seem to work either.

  The unit shows in the management of the computer as a work, I guess by using a Microsoft Driver. The Unit presents itself as "validity sensors (WBF) (PID = 0018)' in the biometric devices topic."

  Any help will be appreciated.

  Thank you

  Hello SauveDuro, welcome to the Forums of HP.

  I see you are trying to install the drivers for the fingerprint reader on the laptop for Windows 8.1, you've seen questions get this working.

  Unfortunately, HP does not drivers for Windows 8.1 for your laptop.

  The most I can recommend in this case, check the manufacture of each component for Windows 8.1-compatible drivers.  Here's a link of validity, you may be able to get drivers that work for him: http://www.validityinc.com/software/hp/wbf.php.

  This can also help you to: Troubleshooting a (Windows 8) fingerprint reader.

  Sorry for the inconvenience that this may cause. I hope that something can help you.
  Thanks for posting on the HP Forums.

• Cannot install windows 7

  Hello. So I bought the Acer E5 - 527G - 77BU. I installed windows 8.1 Pro without problem. But I really dislike this window, and I want to install Windows 7. But when I plug in the DVD or USB stick with windows, I don't get the option to boot to it (in the f12 boot menu). If I put in the DVD of 8.1 win everything is fine. I can chose from the menu. I'd appreciate your help. Thank you!

  You can set the BIOS to use Legacy instead of UEFI and disable start-up secure if the option is available.

• HP ENVY 700-000z Desktop PC with 8 and the need to know if I can install Windows 7

  Just bought HP ENVY 700-000z Desktop PC equipped with 8 and need to know if I can install Windows 7 on this computer without problem.  My work does not allow the use of Windows 8.  If I can install Windows 7, what version of operating system do I need to buy to do a clean install.

  If I understand correctly, I could order the Windows 8 Pro, who has right to demotion and then install Windows

  7 pro, I have then I should be able to get the drivers, I need HP is correct.

  WARNING *.

  HP does not recommend installing Windows 7 on a computer comes with Windows 8, and it will support the installation of Windows 7. HP doesn't provide drivers for Windows 7 and the appropriate drivers are not available for the hardware in the computer. In addition, Windows 7 can not take in charge some of the hardware or software designed for the computer.

  Make sure you create your media recovery HP or USB Flash Recovery discs before you edit or change anything.

  You should ENABLE 'Secure Boot' and maybe 'Legacy Support' in the 'BIOS Setup boot secured' on the settings page below, before you try to install Windows 7;

  

  or

  

  In addition, as the hard drive is partitioned as TPG, you must start the computer by using the "UEFI - CD/DVD drive" in the start menu "F9". If "UEFI - CD/DVD drive" or something to that effect does not exist in the start menu, please post a screenshot and/or make startup listed options.

  I suggest using Windows 7 SP1 for the best installation experience. If you need Windows SP1, see 'How to install Windows 7 without the disc' to download and create your own. If the DVD does not start as UEFI, you may need to use a USB Flash drive (can ask "Quick start" DISABLING in BIOS) as the installation media. Please download the Windows 7 USB/DVD download tool to create a Windows 7 SP1 USB Flash drive.

  Most of the Windows 7 drivers from the drivers of HP Pavilion p7-1299 c desktop PC page should work on your desktop HP ENVY 700 - 000z CTO. Both models use a variant of the motherboard HP Jasmine. If you have missing or unknown devices after installing the drivers, please post the "Hardware ID" Device Manager for devices as shown in the example below.

  

  If you have any other questions, feel free to ask.

  Please click the White Star of KUDOS to show your appreciation

• Install Windows 8.1 64 bit on Latitude E6510

  Hello forum,.

  I failed repeatedly to install Windows 8.1 Pro 64 bit on my Latitude E6510 (from July 2010). Windows 7 Pro 32 bit was preinstalled, when I bought the laptop. As I've recently updated the 3 to 8 GB RAM, I would use a 64 bit system now.

  I tried to boot from the installation DVD and windows flag is displayed. After a few seconds, a message on blue background: ": (your PC) has encountered a problem." We collect certain information and then we will restart it for you. "It's the message, as FAS as I can remember. It appears only for a second, and then the computer restarts automatically. I have no chance to enter an installation menu.

  I tried an update of the A03 BIOS to the latest version A16 without success. Boot mode is set to legacy at the present time, I also tried UEFI temporarily, without change...

  Any help would be appreciated.

  I finally solved this problem by replacing my new 8 GB of RAM with 3 GB old RAM modules that were previously installed when I bought the laptop. Subsequently, Windows 8.1 boots without fault of the DVD.

  I really don't know how these two things can be combined between them, but maybe this message can be useful, if someone has the same problem in the future.

• Need help to install Windows 8.1 on the partition, bootcamp on Macbook Pro 15 "mid-2010 w / no optical drive"

  I tried for almost a week in all possible ways to get windows installed on a boot camp partition on my main SSD 1 TB drive as a partition, or on my HARD drive, which is installed in place of the optical drive.  So far, everything I tried to give me some sort of error at some point in the process.  It seems that many of them are case by case, so I thought that I invite you all and see if you can help!

  I use a Macbook Pro 15 "mid-2010 that I improved with a 1 TB SSD drive as the startup disk.  My optical drive was not functional, so I moved my old 500 GB HARD drive to the location of the optical Bay.  I am also under the latest version of El Capitan (10.11.6)
  Here are my system specs:

  
  Presentation of the material:

  Model name: MacBook Pro

  Model identifier: MacBookPro6, 2

  Processor name: Intel Core i7

  Processor speed: 2.8 GHz

  Number of processors: 1

  Total number of cores: 2

  (By heart) L2 Cache: 256 KB

  L3 Cache: 4 MB

  Memory: 8 GB

  Processor speed of interconnection: 4.8 GT/s

  Boot ROM version: MBP61.0057.B11

  Version of the SCM (System): 1.58f17

  What I tried (from what I remember):

  I tried to change the Bootcamp info.plist file for my version of the macbook pro to use a USB stick for the installer.  It seems to have installed correctly but once I partition the disk and restart the computer, it gets stuck on a white screen with the Apple logo and I am forced to make a hard stop and then hold down option to boot into OS X, recovery, or the EFI Boot.

  If I go through the windows installation to start the EFI system, I get an error of:
  "Windows cannot be installed to this disk.  The selected disk is a MBR partition table.  On EFI systems, Windows cannot be installed on GPT disks. »

  I also tried to create a partition by using disk utility, and that too made me an error in the installation of windows.

  So far, the only way that I'm away from windows to run at all has been using the free trial of VMware Fusion 8... but I intend to use windows for more intensive tasks like audio pro, and merger simply does not offer the performance necessary to run these programs.  I'm hoping to install windows 8.1 on my internal SSD or HARD drive, regardless of the work - as long as OS X and files associated with it are left alone.

  If someone could help me please understand this point, I would really appreciate it!

  Thank you

  If your computer has an optical drive, you must use the optical drive to install Windows using Boot Camp Assistant.

• Cannot install Windows 8 on retina Macbook Pro 2011

  I try to install and run Windows 8 on my Macbook Pro 15 "retina end 2011 with OS 10.10.5."

  I read a ton of forums, and they say all get a Windows 8 ISO from Microsoft Web site. I did it.

  Then, they say get a Virgin USB key and plug it in. I did, and I put the ISO on my USB external drive.

  Then he said: open Boot Camp Assistant, what I do, but then it does not match what say all forums. When I open the Boot Camp Assistant, he goes to the Introduction page. I click CONTINUE and the next page says SELECT TASKS. The only two available tasks are to "Download the latest software from Apple support" or "install Windows 7 or later.

  I select both, it asks me to select my destination drive, what I do, then click "CONTINUE".

  It downloads the Windows support software.

  Then I get an error message that says "Installer disc cannot is, wait a few minutes for something (I forget exactly).»

  So I wait and nothing happens and I'm back on the screen SELECT TASK.

  ANY HELP MUCH APPRECIATED.

  Greetings Peter Degaillande1,

  A MacBook Pro and MacBook Pro with Retina display requires different versions of Windows due to their different abilities. Here is the information you need to determine what Windows operating system can be installed on your.

  Use Windows on your Mac with Boot Camp 8.1 - this article explains what MacBook Pro models can install Windows 8.1 and the steps on how to do this.

  Install Windows 7 and older versions on your Mac with Boot Camp - this article explains what MacBook Pro models can install Windows 7 and previous versions, as well as the installation steps.

  I hope this helps!

• I tried to install Windows 8.1 on my MAcBook Pro mid2010 running that el Capitan - failed

  I tried to install Windows 8.1 on my MacBook Pro mid2010 running El - Capitan

  Boot camp could locate the iso file or CD the I burnt out of it.

  Any idea? should I try with Win 7?

  On a 2010 model, ISO (or installer USB) is not supported. Can you burn W8.1 to a physical DVD, and try to install using Wizard of BC?

  Please also see using 8.1 for Windows on your Mac with Boot Camp - Apple Support , and check to see if your specific model is listed.

• Try to install Windows 7 via USB, El Capitan, Macbook Pro 2011 but get this error "No. BOOTABLE DEVICE - INSERT BOOT DISK AND press ANY KEY ' when bootcamp restart my macbook to begin the installation. Any ideas?

  I am trying to install Windows 7 via USB, (El Capitan, Macbook Pro - early 2011), but this mistake "No. BOOTABLE DEVICE - INSERT BOOT DISK AND press ANY KEY ' when bootcamp restart my macbook to begin the installation. Any ideas?

  You cannot use a USB on Mac 2011 Installer. Please burn the ISO on a physical DVD Windows (a DVD - R Carbon SL on the rate of burning slower is better) and use it to install Windows. The file Info.plist changes only allowing the creation of USB, but does not fully support a USB Installation.