Installation of post RAM problems

Hi all

I have a little problem after I recently installed a 1.0 GB 400GHz Module RAM in my computer 2 days ago. As expected, the RAM module was automatically recgonize when starting up. After booting up I open the Task Manager to check the performance and 1m02s just later the CPU usage rises all the way up to 100 percent and he declined the use of the processor. I bought RAM to increase my computer performance not decrease.

I have a Dell Deminsion 3000

Here is my System Information:

System:
Microsoft Windows Xp
Home Edition
Version 2002
Service Pack 2
 
Computer:
Intel (r)
Pentium (r) 4 CPU 2 .80GHz
2.79 GHz, 1.25 dildo RAM

I recently ran disk cleanup, disk defragmentation and uninstalled antivirus software, thinking that perhaps the source however problem remains.

Could someone help me please to solve this problem?

(1) first try running Memtest86 +: "with the two sticks of memory installed.

It runs from a floppy disk or CD, you must remove or
confirm whether your one or more of your sticks of memory are bad or the values of the SPD in the BIOS are correct. Let it run for as long as you can: 2,4,6,8 or several hours (at least 3 full passes), if no errors at that time then your ram is OK.
http://www.memtest.org/
Memtest86 + Guide/How To (use the.) ISO to create a bootable CD)
http://www.overclockers.com/forums/showthread.php?t=409152

(2) remove the new memory and see if the problem disappears and the CPU load is back to normal.

(3) remove the original memory and only insert the new memory (in the same dwelling original memory was in) and try again to run Memtest86.

Note: any time you remove or install memory do it with the computer turned off AND removed the power cord. After removing the power cord, wait 5 minutes before removing or installing memory or other hardware component.

JS
http://www.PAGESTART.com

Tags: Windows

Similar Questions

  • Where can I post a problem of Aspire One AO756 USB system recovery?

    Hello.  Where can I post a problem of Aspire One AO756 USB system recovery?  I had a HARD drive crash, replaced the HARD drive and bought a USB (Win 8.1) on the Acer Store system recovery disk.  The USB settles all the installation files and then said to remove the USB key, then click OK to restart.  But the bios can not find a bootable disk to complete construction. I was sent a second USB drive with the same results.  The new HDD Seagate passes each Seatools test.  In addition, I can boot from USB to the DOS or Linux and access the disk without problem. Thank you

    You must use diskpart. in the windows setup program, there is an option to format the partitions manually. allows to delete all partitions, and it will automatically set the MBR or GPT disk.

  • Error: "SQLDUMPER library failed initialization.your installation is either corrupt or has been tampered with please uninstall then re run the installer to correct this problem.

    Original title: "SQLDUMPER.

    When I start my laptop windows xp, an error message appears "SQLDUMPER library failed initialization.your installation is either corrupt or has been tampered with please uninstall then re run the installer to correct this problem.

    Hi mark25666,
     
    Here's a similar post on this issue. Check the suggestion given in the link and see if it helps you too the question of fixing.
     
    If this is not enough, post your query in the SQL Server instances for better assistance.
  • It didn't install the package when I download the Flash Installer. Are there problems with Adobe?

    It didn't install the package when I download the Flash Installer. Are there problems with Adobe?

    I don't know what you've downloaded; Try

  • Installation/space Windows Vista problems

    Recently the Windows Vista Setup program does not allow the installation of the different software components.  Sometimes I have a vague (as impossible to install) error code, sometimes the installation starts from inside IE and then just comes back to IE. But no installation occurs.

    I am slot as Vista Business 64-bit Service Pack 2. (5 gig Ram)

    I have between 50 to 500 free MB on the disk. (I have a drive c to 35 gigabytes.  But, windows uses 31 G (winsxs uses 20 G).)  Supposedly, it's a problem of Microsoft to know during the years that they have no desire to fix.  I regularly try to clean the space, but it's like trying to hold back the Mississippi...

    Uninstall seems to work.

    I ran various utiilties of Microsoft to try to resolve the problem. (I think this is worse!)

    I ran sfc/scannow and it has detected/fixed no problem.

    When I was able to capture more storage space (by moving my virtual memory on another drive) briefly the problem has not disappeared.  The Publisher of the software after several hours of searching in various newspapers told me it was a problem of Microsoft Installer.

    I don't want to re - install the OS that I don't have a number of my installation for different software products discs (they are all legal).

    I'm not so sure that Windows installs my updates properly at this stage either.

    Any help would be appreciated.  I'm drowning in time to support.

    What is E? The dual computer boot or pagefile on E refers to the operating system in C?

    I did not used Easeus Partition Manager, Partition Magic and Acronis who buy software using, but the principles will be similar. What you need to do is to reduce the size of D, so that there is a free space between C and D, and then increase the size of C in this space. You can then increase the size of D in the original unallocated space of 5.86 GB in D.

    I suggest that you study the knowledge base, and there is a line on manual. Print the relevant parts. The FAQ in the first link and follow two particularly relevant links:

    http://www.partition-tool.com/EASEUS-partition-Manager/FAQ.htm

    http://www.partition-tool.com/EASEUS-partition-Manager/FAQ/technical-faq32.htm

    http://www.partition-tool.com/knowledge-base/how-to-extend-system-partition.htm

    Good luck.

  • 650 HP laptop with Windows 7 32 bit Home premium RAM problem

    Hello.

    I recently purchase a new HP650 notebook that came with Windows 8.  I have this wiped and reinstalled windows 7 32 bit edition Home premium and downloaded all the drivers/software relevant on the HP site.

    However, the machine is supplied with 4 GB of RAM, including the BIOS see' good sas.  Windows 7 recognizes that 4 GB but it says that only 969 MB is usable.

    There is nothing of configurable in BIOS for the use of video memory or information about the reserved addresses.

    I am aware that 32 bits will use about 3.5 GB but wow can get this machine to use all 3.5 GB?

    Any advice would be apreciated.

    Thank you very much

    James

    Hello

    I suggest that you uninstall the Windows 7 Home Premium (32 bit) and switch on Windows 7 Home Premium (64 bit) version to treat memory problems.

    The Microsoft Windows 7 activation key on the certificate of authenticity you have for the 32-bit version will work with the 64-bit operating system. The caveats are that you can have only a single installation active with the license key at a time and you must have an installed processor that is capable of 64-bit OS.  You will find that the 64-bit version is far superior to the 32-bit version for stability. Of course, there is the increased ability to recognize more memory installed up to limits of the motherboard.

    You can download the 64-bit here. The drivers are available on the support portal web for your mobile in the section download.

    Erico-

  • Upgrade to 4 GB Ram problem - computer desktop OptiPlex 780...

    Nice day

    Thank you for your services.

    I am trying to upgrade my desktop computer model # OptiPlex 780 and it's the standard I force the affected elements before, after I check what is the speed of compatible ram, voltage and timing, then I bought this model:

    KHX1333C9D3B1K2 / 8G

    Sound of Kingston - hyper-x blue or you can check the details by the Munificent code above or visiting them this link:

    http://www.Kingston.com/datasheets/KHX1333C9D3B1K2_8G.PDF

    The problem:

    When I delete the original 2 GB Ram and installed this 4 GB ram on the first location, the departure of light 1 # & 3 led with sound as continuous hum without starter or windows interface.

    I tried to:

    -Change the slot

    -Fix the maximum ram which is 4 GB for each slot up to 16 GB

    -Correction of the original 2GB ram in slot 1 then fix the new ram in slot 2 or 3 and 4

    -Update the BIOS to version 15A and update all the drivers from dell.com

    -I make sure that the ram is compatible Guide Dell book on this link:

    http://i.Dell.com/sites/content/business/solutions/engineering-docs/en/documents/OptiPlex-780-tech-guide.PDF

    So please help me in this case, it is urgent and I used this computer in the main office and my work.

    Thanks and regards,

    BYQ-

    svanwormer

    I have a 780 with the Intel E7500, Q45 chipset and A15 BIOS CPU and I'm running 12 GB of DDR3 RAM. Two 4 GB and 2 GB

    Yep, catilley, I'm afraid, you're just wrong on this point - your info is old, apparently.  I, too, running an Optiplex 780 with an Intel Core 2 Quad 9550 CPU, chipset Q45 and 12 GB of DDR3 memory - in fact, it's the same machine that I write this response at this time.

    As I posted a year ago on this thread, the official manual of Service from Dell for Optiplex 780 confirms it will take up to 16 MB of memory DDR3, 4 GB per slot.  Here is the link, directly from the Dell website:

  • RAM problems & windows 7 64 bit or Windows 7 32 bit

    Hello

    Have Presario SR5440AN

    2 GB of RAM (2 x 1 GB - factory loaded)

    Windows 7 Ultimate-32 bit

    NVidia Geforce 9500 1 GB DDR2 GT graphics

    The Porcessor AMD Athlon 64 x 2 Dual Core 5200 + 2.7 GHz

    My question is in 2 parts.

    (a) what's causing my next problem?

    4 GB (2 x 2 GB) of RAM Corsair DDR2 - 6400 compatible according to my survey.

    When I try to load it (ie. replace the current 2 x 1 GB RAM) the computer freezes or restarts the Windows 7 logo at startup.

    Does not extend beyond this point.

    If I load 1 x 2 GB Corsair computer loads OK BUT system is unstable and will randomly reboot or hang.

    (b) would be using 64 bit Windows 7 with his problem?

    Can I load Windows 7 64 bit (like the AMD 64 x)?... and she would help load and make use of the 4 GB of RAM I have.

    Thank you very much.

    jimmyjamster

    jimmyjamster wrote:

    Hello

    Have Presario SR5440AN

    2 GB of RAM (2 x 1 GB - factory loaded)

    Windows 7 Ultimate-32 bit

    NVidia Geforce 9500 1 GB DDR2 GT graphics

    The Porcessor AMD Athlon 64 x 2 Dual Core 5200 + 2.7 GHz

    My question is in 2 parts.

    (a) what's causing my next problem?

    4 GB (2 x 2 GB) of RAM Corsair DDR2 - 6400 compatible according to my survey.

    When I try to load it (ie. replace the current 2 x 1 GB RAM) the computer freezes or restarts the Windows 7 logo at startup.

    Does not extend beyond this point.

    If I load 1 x 2 GB Corsair computer loads OK BUT system is unstable and will randomly reboot or hang.

    (b) would be using 64 bit Windows 7 with his problem?

    Can I load Windows 7 64 bit (like the AMD 64 x)?... and she would help load and make use of the 4 GB of RAM I have.

    Thank you very much.

    jimmyjamster

    What do you mean by "compatible according to my survey?

    It is important that you buy only guaranteed compatible RAM. It is if you want it to run without problems like those you meet.

    You bought a good brand, but it is not enough. If it is guaranteed compatible RAM, I suggest go back because it does not work. Modules of memory are not lacking. Even those brands as Corsair.

    Installation of Windows 7 x 64 won't help. A 32-bit Windows 7 installation will be @ 3.25 GB of the 4 GB available. That's enough. Only install a 64 bit OS if you want or need to use more than 4 GB of RAM. The following image lists guaranteed for your Corsair PC compatible memory. Corsair indicates that 4 GB modules are designed for computers with 64-bit operating systems.

  • iMac 27 2010 graphics card / ram problem

    Hello - read through the form and try to isolate the problem.  A week ago my end 2010 iMac 27 I7, 12 GB of Crucial Ram, OSX Yosemite went screwy - icons went fuzzy, and the system has just stopped responding. I tried not just pull the plug, but the computer was out of order, so I had to pull the plug. Please keep in mind it was a day hot here in New York and I've come for a quick moment to remove some files and did not close the windows a turn on the AC, so they probably overheated system or so I guess

    Anyway, after a few hours and I came back home and turned back on the iMac. Immediately, I noticed some pale red bans on the screen. The system has been restarted slowly and then it stop at halfway however and just go to the gray screen. I did a reboot, re-installed the operating system made the system check, but the failure of operating system to kick when I do a normal restart, and I am only able to operate the computer in Mode safe.

    Is there a way I can understand if the RAM is the question, the graphics card, or if it's the OS? A faulty graphics card will prevent the system from starting normally? I have the same question when I open it on safe mode?

    I'm trying to see if there is a way to save the iMac and get more use out of it, but at the same time a few years if it's gong to fix an expensive that I can't do on my own, so maybe its not worth what's now 5-6yrld of fixing iMac little matter how the computer cost me back in 2010.

    Thanks for your help and sorry if this question has been answered countless times before.

    JB

    Most likely graphics card problem...

    Note:

    One way to test is to boot from the HD, (now shift key at startup), run utility disk in Applications > utilities, then highlight your reader, click on repair permissions, test for problem in Mode safe...

    PS. secure boot can remain on the gray radian for a long time, let go, he's trying to repair the hard drive & trash/rebuild the cache files

    Reboot, try again.

    If it does so only in ordinary chest, there could be a problem material such as Video card, (the Quartz is disabled in Safe Mode), or airport, some USB or Firewire devices, or the module in part 3, Check System Preferences > accounts (users and groups in later versions of OS x) > login items window to see if she or something relevant is listed. Or a stray process eating RAM.

  • RAM problem

    I have 8 GB of RAM installed in my MacBook Pro. Suddenly, I found almost all of this is in use, making my computer run like molasses in winter. I recently installed a updat for OSX but don't know if that is the question. I run many apps and just do basic stuff, nothing complicated. And it is not consistent, either.

    All used RAM isn't the problem. That's the idea and the OSX is very good in management RAM.

    After a report of etrecheck for an analysis of your system.  http://etrecheck.com

  • Installation of Qosmio G30 problem

    Hello to all the boys

    I have a huge problem

    I have a Qosmio G30, recently he repeats, or used the disk, format it, confg. RAID, it will restart the formatting begins, ends will restart and the problem here.
    Resuming at the end of installation, which occurs not because the video driver crashes (nv4_disp). So, every time I turn on the PC are always half installation.

    I ask for help! And while we are to what you enter into the BIOS of Toshiba Qosmio G30.
    Thank you

    To be honest, your assignment is a little confusing for me. If I understand you right, you want to install own OS, right?

    Are you using the original recovery for the OS installation disc or you try to use the clean version?

  • Mac Mini Ram problem

    Hello

    I just replaced the hard drive in my Mini 2011 Mid and during reassembly of the Mini and reinstall the RAM modules, the top was hard to seat. When I got the upper module in it makes a sort of "Bully" of noise (metal grid sound). At the start, I had the three beep to tell there is a problem of RAM card. I took the modules and re-sitting them, top of page gross sounding again. Same three beeps.

    I then took the upper module and has attempted to restart the machine - it booted up OK.

    What happened here? I destroyed the motherboard? Is this a known issue? Any thoughts appreciated.

    Inspect the contacts on the memory that went into the top slot. Inspect the top slot anomalies such as curved plastic and bent or corroded contacts.

    Other users have damaged locations when replacing memory. Can be caused by does not receive the baton in properly and forcing, debris got into the slot or on the key and he was forced in.

    I think that now the slot is damaged. and yo either have to replace the logic board or only a slot to use.

  • Satellite A60 - possible ram problem

    I have a satellite a60 he says he has 256 RAM. on aol checking my computer tells me that I have only 192 RAM anyone any idea, what the problem might be?

    [Edited by: admin on 22 May 05 20:28]

    Hello

    I suspect that your RAM is shared with your graphics (usually 64 MB) so even if you actually 256 MB RAM, 64 MB is pré-alloué graphics use 192 MB. Your computer AOL chack reports available rather than the actual RAM RAM

    HTH

  • Satellite 5200 701: RAM problem?

    Hello

    After my last thread, I could somehow isolate the problem further.

    My Satellite 5200 701 boots Win XP correctly, but when it is lifted upward or to the smallest shake the screen freezes or displays the Win screen in strange colors. When I hit carefully on its underside after you have started successfully, it crashes immediately when I touch the part of the cover of RAM.

    So, I guess it has something to do with the RAM. However, both RAM blocks have been verified by Toshiba, as well as the HARD drive.

    Does anyone have a solution?

    1 million thanks!

    Hi Moritz,

    According to your description of the problem, it is most likely something made intermittent contact where your RAM modules are connected. Try to remove and then reposition modules RAM themselves (by taking the necessary precautions of antistatic property course) to see if that helps. Make sure that the RAM modules are in place and properly locked in place.

    You can also try exchanging the RAM autour modules so that they are in the bays of spare.

    If your problem persists, then it is likely that there is a bad connection between takes of the RAM and the motherboard connections.

    HTH

  • Pavilion P7 - 1003w Win 7 sp1 - RAM problems...

    I have a Pavilion P7-1003w running Windows 7 sp1.  I have 2 strips of 4 GB of RAM installed, which should show that 8 GB under Windows Properties.  Instead it shows 16 GB (7.75 exploitable).  I tried to remove 1 stick and leaving 1 installed, the results show 12 (3.75 usable) GB.  I tried each stick individually in each of the 2 available DIMM slots and each time I get the same results.

    Why is this, and can it be fixed?  Or maybe it's bad advice?  Any suggestions are appreciated.

    Hello

    Open RUN and type: MSCONFIG---> look under the startup--> advanced options tab and make sure that both the box processor memory box and maximum is not checked.

    Try to clear the CMOSin case that the BIOS is damaged.

    Open the window RUN (admin) and enter: sfc/scannow

    RAM reporting problems in the past have been associated BIOS.  Try to install the release of updates to the BIOS.

Maybe you are looking for