installation of switchport lwapp running of multiple ssid access point
Hi all
When you set up a hotspot lwapp, must I trunk all the VLANS on the port to the ap? or do I only allow the vlan management for the access point? That is to say 1 vlan and normal access port?
see you soon
Carl
If it's a LWAPP AP, then the switchport should be an ACCESS PORT... It's just to get the IP to the AP, then the AP wil try to join the WLC... once that the AP has joined, the SSID and the rest through the LWAPP tunnel...
Concerning
Surendra
Tags: Cisco Wireless
Similar Questions
-
RV180W - multiple wireless access points
Hey there, looking for some advice.
I currently have 2 two devices Cisco RV180W and I'm looking to expand my saturation wireless in my house and you're looking for the best way. a bit of back story... I originally had a signal (1) RV180W and it was in my basement (essentially a pop room configuration) and on the top floor of my house, the signal was very week. I found a text of presentation mentioned due to the chipset RV180W best wireless Extender/Expander was actually another RV180W and just used in an access point mode. So now I have two of these devices whats their best way to put in place? I saw two different implementations in this scenario and im not sure which is best.
1. install a WDS network. Add each as authorized access points.
2. installation each with the same SSID but together on different channels.
What is the best configuration for the best saturation wireless within the House thus maintain the client when hoping between AP connections? also looking for easy management.
Hello
I would say your best bet here would be option 2, with a wired connection between them.
WDS can be useful, but it has a few drawbacks. For each hop that you take your speed will get divided by two, since each station can send or receive at the same time, not both. With a wired connection eliminate you this additional relay between a router and the other on the air and can get better wireless performance.
One thing I should mention, is that neither the installation program will result in customers maintaining connections perfectly while hopping between APs. This would require something called seamless roaming, which is only available on the business access points where there is a controller wireless LAN involved.
However, most of the time when hop customers between two networks it will be very fast and they will lose only briefly about connections. The decision on the time of the actual customer belongs, so that all devices will act in the same way.
So in short, the same SSID on different channels is your best bet, ideally the channels 1, 6 or 11 If you do not overlap.
In regard to the ease of management, they will be essentially two independent devices, each managed separately. But once you set up the access point RV180 it will not be too many reasons to change the configuration, except maybe to change the wireless password.
Thanks for choosing Cisco,
Christopher Ebert - Advanced Network Support Engineer
Cisco Small Business Support Center
* Please note the useful messages *.
-
How connect N600 router wndr3400v3 to another hotspot or wifi ssid access point
I want to connect to my router to an another ot hotspot or access point ssid to increase network range
I tried but not found any option
Help, please
Ok thank you
-
BVI Interface inaccessible since the addition of multiple SSID
Announcement to the community for the first time.
I have a simple HomeLAN which consists of a Cisco router for series 800-> switch PoE Cisco3560-> Cisco Aironet 1131AG Access Point.
Everything works well for a while in which I had a simple port to "change the access mode" configured on the switch facing the AP and one SSID on the access point that is configured in stand-alone mode (without controller).
My provider has enabled IPv6 on my broadband connection and I started to reconfigure my installation this afternoon to allow this.
I decided to run only a bunk Dual LAN and a separate native IPv6 only test LAN for proof of concept.
With this in mind, I changed the switch port to the access point to a "mode trunk switch' using simple dot1q encapsulation. I have also consulted the post helps very https://rscciew.wordpress.com/2014/05/24/multiple-ssid-configurations-on... after finding in this community post on the topic of multiple SSID https://supportforums.cisco.com/discussion/10899511/how-broadcast-2-ssid...
I have now two SSID broadcasting (we will call double stack and ipv6 only for the sake of the argument). The SSID double stack uses VLAN 2 and 1 bridge, while the SSID only ipv6 uses 6 VLAN and bridge 6.
I must stress at this point that my router (where I want to layer 3 for the two LANs gateways) I have DHCP, DHCPv6 and SLAAC configured on relevant VLANs.
I seem to be the 2 VLAN trunking of properly and I can see the SSID broadcast in my house. I can connect to the SSID (authenticate and form an association as seen in 'show the dot11 association'), but I don't get an IPv4 address or IPv6 assigned to all clients (I tried Mac OS x, iOS, Android, and Windows phone). Furthermore, I can't ping the IP bvi1 of the AP - that is the element that is annoying me more that I must console to the AP to make any changes at all.
Here is an overview of my AP configuration, with relevant parts removed for safety...
dot11 syslog
!
dot11 said ipv6 only
VLAN 6
open authentication
shared authentication
authentication wpa key management
MBSSID-guest mode
WPA - psk ascii 7
!
dot11 said double stack
VLAN 2
open authentication
shared authentication
authentication wpa key management
MBSSID-guest mode
WPA - psk ascii 7interface Dot11Radio0
no ip address
no ip route cache
!
the cipher mode vlan 6 encryption tkip aes - ccm
!
the ciphers of vlan 2 encryption tkip aes - ccm mode
!
has declared ipv6 only
!
such double stack
!
MBSSID
root of station-role
Bridge-Group 1
Bridge-group subscriber-loop-control 1
Bridge-Group 1 block-unknown-source
No source of bridge-Group 1-learning
unicast bridge-Group 1-floods
Bridge-Group 1 covering-disabled people
!
interface Dot11Radio0.2
encapsulation dot1Q 2
no ip route cache
Bridge-Group 2
the bridge-group subscriber-loop-control 2
Bridge-Group 2 block-unknown-source
No source of bridge-Group 2-learning
No extinction unicast by bridge-Group 2
Bridge-Group 2 covering-disabled people
!
interface Dot11Radio0.6
encapsulation dot1Q 6
no ip route cache
Bridge-Group 6
the bridge-group subscriber-loop-control 6
Bridge-Group 6 block-unknown-source
No source of bridge-Group 6-learning
No bridge Group 6 unicast-flooding
Bridge-Group 6 covering-disabled people
!interface FastEthernet0
no ip address
no ip route cache
automatic duplex
automatic speed
Bridge-Group 1
No source of bridge-Group 1-learning
Bridge-Group 1 covering-disabled people
!
interface FastEthernet0.2
encapsulation dot1Q 2
no ip route cache
Bridge-Group 2
No source of bridge-Group 2-learning
Bridge-Group 2 covering-disabled people
!
interface FastEthernet0.6
encapsulation dot1Q 6
no ip route cache
Bridge-Group 6
No source of bridge-Group 6-learning
Bridge-Group 6 covering-disabled peopleBridge IRB
1 channel ip bridge
interface control2
MGMT AP Interface Description
address 192.168.1.6 IP 255.255.255.0
no ip route cacheIP default-gateway 192.168.1.50
As you can see I can not ping the gateway of AP - I would be very grateful if someone could point me in the right direction with regard to what I'm doing wrong here?
Thank you
Mick
OK means your AP is to have IP vlan2:
Do it like this and try again:
!
interface Dot11Radio0.2
encapsulation dot1Q 2
encapsulation dot1Q 2 native
Group 1 bridge
Bridge-Group 2
!
interface FastEthernet0.2
encapsulation dot1Q 2
Group 1 bridge
encapsulation dot1Q 2 native
Bridge-Group 2!
Or alternatively, you can delete the name native dot11radio0 and fa0.2. (It should also work without it), but be sure that for vlan 2 you have bridge Group 1.
Concerning
Remember messages useful rates
-
Multiple SSID on AIR-SAP702I-E-K9 (700 Aironet Access Point)?
Hello community
I wonder if it is possible to simultaneously run multiple SSID (actually 3) on a single Cisco AIR-SAP702I-E-K9, which is a standalone AccessPoint (AP). Each SSID should be linked to a different VIRTUAL LAN. Or do I need another model or even an AccessPoint driven by the controller to run multiple SSID on different VLANS to the same AP?
Thanks in advance.
Kind regards
AdrianHi Adrien,.
Yes, you can have multiple ssid on the AP standalone. Each SSID must be mapped to a VLAN different.
Kind regards
Shubham
Please do not forget to note positions that answered your question and mark as answer or was useful
-
Windows Installer Cleanup Utility cannot run because corrupt Microsoft installation Service
I can't get the Microsoft Installer Cleanup utility to run, I get an error message "the Microsoft Installer could not access the Service." I tried re-registration of the service nothing is done. I work on a customer's computer and can not get KB2467173 or Windows Live Essentials update, so I am unable to run internet explore in the standard 32-bit functionality.
I would avoid reinstalling Windows if possible.
Note: Windows Installer Cleanup utility is no longer supported and is not available via a Microsoft page.
Comment: If your client is in the habit of running "Registry cleaners", a clean installation of Windows will be your only recourse.
-
having a problem installing drivers for a new Epson printer scanner all in a WF-2530 on my desktop using windows vista
error message "could not launch the required program during installation, check the installation disc, then re-run the installer.
I managed to install the software on my laptop using windows 7.
spending some time with epson tech dept, after several attempts to solve the problem, they advised that it was a problem with the microsoft software.
have tried to install it on the internet from the site of epson, but same error
any help would be greatly appreciated
< have="" tried="" installing="" over="" internet="" from="" epson="" website="" but="" same="">
Do you mean that you have downloaded the Epson driver?Try using the wizard adding printer in the Control Panel, printers. In the wizard, select EPSON under manufacturer. If you don't see your printer in the list, click the Windows Update button. It will take several minutes (about 20) be patient, Windows updates the list. You should see a hard drive activity during the update.
If that wouldn't work, try to run the System File Checker:
Use the System File Checker tool to troubleshoot missing or corrupted on Windows Vista or Windows 7 system files
http://support.Microsoft.com/kb/929833?WA=wsignin1.0 -
original title: problems with the installation!
I'm trying to reinstall iTunes I have experienced problems with it. However, when I try to install an error pops up saying something along the lines of "there is a problem with this windows package install." A program to complete this installation could not be run "." I have no idea why this happens and no idea how to solve this problem.
Any help would be great.
Error 9010
To disable the Desktop Window Manager by process - response: this is a normal message when a process requires exclusive access to the desktop (e.g. use DirectDraw /OpenGl in exclusive mode) or just likes to turn off the Messenger of the window of the Office for some reason any. It is not an error.
Error 9013
Press Windows Flag + R
Type %windir%\system32\SystemPropertiesAdvanced.exe
Press OkUnder performance, click the Settngs
Check enable the Composition of the Bureau
Click on apply, Ok
Error 1002 - I need the specific message
Installation of the Windows Installer Application
http://TechNet.Microsoft.com/en-us/library/cc735604 (WS.10) .aspx
Error 1001-
Installation of the Windows Installer Application
http://TechNet.Microsoft.com/en-us/library/cc735588 (WS.10) .aspx
Reset the Web browser
Tools > Internet Options > Advanced tab
Click on the Reset button
Check delete all personal settings
Click on the Reset button
Click Ok
Close the window
Restart the computer for the changes to take effect
Retry Installation
Error 100 - support contact Apple
http://TechNet.Microsoft.com/en-us/library/cc774985 (WS.10) .aspx
-
Installer Windows continues to run.
The Windows Installer continues to run whenever I do any type of activity from Solution Explorer or launch a desktop application. I am running Office XP on Vista Home Premium and it used to work fine, until I rebooted my PC. I installed the Vista service packs before you reinstall all my programs and this is where the problem started. All other programs work very well. I have admin on the account that I use and UAC turneed off right. I have all the updates of Windows installed. No matter if I run the first program or open a document to open the program. I always get the message that wimndows is to install office, and then configure it. Any ideas? Installer Windows continues to run
Hi smlandau1,
This only happens when you try to open Office XP?
You can try the following steps and check if you can solve the problem.
Step 1: Start the Windows Installer service
1. click on Start, type Services.mscin start Searchand press ENTER.
2. double-click click Windows Installer
3. set the start type for Windows Installer to manual
4. click Start start service.
Step 2: you can also try the steps followingRéinscrivez Windows Installer and check if it helps
a. clickStart, type %windir%\system32\msiexec /unregserver in the search box and press onENTER.
b. type%windir%\system32\msiexec/regserver , and then pressENTER. If you are prompted for an administrator password or a confirmation, type the password, or click on allow
Step 3: install windows upgrade.
You can check the following link to download the latest version of windows installed click on the link
Hope this information is useful.
Boumediene. K.
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
WLC 2504 several VLANs multiple SSID
I have three sites
Data center management unit A - main - controller + Access - Point IP 172.16.x.x - Vlan 38
Unit B - system managed by controller IP 172.17.x.x - Vlan 38 Access Points
Unit C - system managed by controller IP 172.18.x.x - Vlan 38 Access Points
In the network topology OSPF runs. We have several VLANS about 38 we wish to propagate through SSID, but maybe I'm not create more than 16. How to make a movement of the user of a unit for unit B how do mention Vlan IP for the user because it is 38 Vlan spread on each unit.
UNIT A - UNIT B - UNIT C
| | |
172.16.X.X 172.17.X.X 172.18.X.X
| | |
VLAN 2-38 VLAN 2-38 VLAN 2-38
| | |
AP-1 AP-2 AP-3
| | |
User to user-1 user-2-3
Need of advice and suggestion
Hello Saad,
If I understand your scenario, you have 2-38 or 16 VLAN for each unit. To ensure exactly the addressing specific IP must be assigned to the user, you must create groups of AP and add AP group particular AP. Let's say for the 1st floor that you used the subnet 192.168.1.0/24 and AP-group1 so all the first floor AP will be in AP group1. In addition to browse documents cisco you will get any idea on AP groups concept.
In order to obtain roaming when users move from one unit to another unit we configure mobility in the controller. As OSPF is already running then you have reach-ability between the controller.
Hope this information helps you.
-
Unique SSID from the multiple SSID
Hello
We seek to deploy wireless at five sites great campuses, one in each State.
Does anyone have any ideas on the deployment unique verus multiple SSID SSID for each location.
Are the benefits of filing a return and security to identify red devices associated with
a unique SSID.
The question was raised that it would be easier to configure one SSID to scan wireless
devices that have separate SSID different places.
Would appreciate any experience on this design
Mate,
Remember, when you're dealing with WLC, you do not configure the APs. You configure the WLC and configs will be propatated of all APs manages the WLC.
The WLC, you can use up to 18 SSID but you can configure 1 024.
Currently, I have three SSIDS and one of them is for VoWLAN.
Moreover, some hand scanners do not like the (hidden) SSID broadcasting.
-
Hello
I have an AP 1252 and I wanted to know what I need to do to set up to broadcast multiple SSID
y at - it something I need to do on the web interface or something through CLI. Thanks in advance
and have a great day.
Please copy - paste the 'controllers to see the output. This will let us know if we can or we cannot broadcast multiple SSID.
The command to enable this featute is...
AP (config) #int dot11 0
AP(Config-if) #mbssid
SSID #dot11 AP (config)
AP (ssid-config) #no - guest mode
AP (config-ssid) #mbssid - guest mode
SSID #dot11 AP (config)
AP (ssid-config) #no - guest mode
AP (config-ssid) #mbssid - guest mode
This will do
Concerning
Surendra
-
About WLC "one-to-many" designates a LAN VIRTUAL mapped to multiple SSID possible?
The Cisco Wireless LAN Controller Architecture includes this feature (possibility of configuration)?
You can map multiple SSID to a VLAN, but you cannot map several VLANS on a SSID.
-
Multiple SSID for AP in light mode
Hello
I tried to configure an AP that is light to have multiple SSID mode, as I do with autonomous AP but I couldn't, is it possible for an AP in light mode to have multiple SSID? If so, how can I do that?
Thanks in advance for your help.
supported wireless LANs is 512 and the AP you're just 16...
http://www.Cisco.com/en/us/docs/wireless/controller/5.2/configuration/guide/c52wlan.html
-
multiple SSID in autonomous broadcasting 1242ag
Hello
I have a 1242ag AP stand-alone series.
I want to broadcast more than one SSID.
pls tell me the step by step approach considering I am new on the basics of radio a g etc.
It's one of the differences between the LWAPP and autonomous access points... That's y I mentioned "its the rule of thumb in autonomous"
Concerning
Surendra
Maybe you are looking for
-
Safari does iPad 10.0.2
I used an IPad with software 10.0.2 with 27,92 GB of memory capacity and 3.85 GB of available memory + i purchaseevery month £0.99 for additional memory cloud. The problem I have is that whenever I open a screen request 1 who reached Safari blocks an
-
HP Pavilion 8 Windows: my hp pavillion windows 8 has a black screen after I put my password in
After i.put my.password in expenses n then goes to a black svreen. I have tried f11, taking battery, reboot, close to the bottom.., .nothin works... Please.Help
-
Intel Turbo Memory - useful or not?
Hello. can I install this: E20680-002 Intel Turbo Memory Module 4 GB on my Pavilion DV7-1020ea? It would make a difference? I use Windows 7-64 bit. I already upgraded one of the HDD with a SSD Corsair with 535mbs/550mbs-reading-writing.
-
I play games and said to update Flash.
play games and it tells me to update Flash. I've updated, uninstalled, reinstalled and still no help... Please help me. Facebook, all games