Installation of the USB-5680 kills Labview

Similar Questions

• Server does not start after the installation of the USB bootable, ESXi

  Hello

  I installed VMware ESXi 5 on a SSD drive using a bootable USB key, but my server does not automatically start since the SSD after installation. I can boot ESXi in the offered by the BIOS boot menu.

  The startup configuration is perhaps incorrect because during the installation of the USB drive is present, but after the installation, it is not?

  Also has anyone seen this problem?

  Kind regards

  Gijsbert

  Updating the BIOS on the DQ77MK at 49, and you should be able to start - UEFI must never be activated.

• Bootcamp errors during the installation of the USB on iMac mid-2011

  I tried to install Windows 8.1 on my iMac for mid-2011. The problem is that my optical drive is not working properly.

  I created a USB bootable via Bootcamp Assistant on my MBPr and have tried my iMac HARD drive partitioning, using OSX disk utility and disk in recovery mode utility. I tried to leave the space as free and formatted as ExFat and fat.

  At the start of the usb drive and try to install on the bootcamp partition, I get the error that it is a MBR and not on a GPT partition.

  In addition, do not know if it's important, but it is a secondary internal drive. My main drive of OSX is an SSD. I have no problem accessing the drive in question under OSX.

  Help please!

  Mac 2011 (and more) have challenges with no DVD installs due to optical drive problems. Changes to the file info.plist Bootcamp to allow creating install USB works only partially because of start-up problems. Only two solutions that work with a high degree of success are

  1. replace the optical drive, or,

  2 http://forums.macrumors.com/threads/install-a-windows-7-partition-on-mac-osx-wit hout-optical-car-or - usb.1836959 / #post... .

  Following two discussions have some installs successfully, but they usually lead to broken drivers or not functional Apple hardware.

  Re: Bootcamp without optical drive

  Re: Activate Bootcamp install USB for OSX 10.9 * ŒUVRES *.

• Installation of the USB - no scanner detected by the software

  I bought Microtec USB scanner ScanMaker6100 but cannot begin to work with it:)

  Recognize the scanner as a Plug & Play device my PC and install it but the software can't find it.

  I tried to scan on another PC to check and it works so I have problem with my TOSHIBA A60?

  I had send my PC profile to support of Microtec and they suggest the following:
  "your installation of USB needs chipset driver. Currently, he works in "universal". Unmanned correct install cannot USB chipsets support entirely. Normally you have the computer driver MB CD when you buy the computer. »

  My USB controllers in Device Manager are installed like:
  Standard enhanced PCI to USB Host Controller
  Standard openHCD USB host controller
  In devices, I see they are ATI SB200 - USB Controller and ATI SB200 - USB 2.0 Controller.

  I really should reinstall / update my USB driver? How? Where can I get these drivers?

  [Edited by: admin July 16 05 12:34]

  Hello

  I don't think you need to install or update the USB drivers. If the scanner is properly installed and recognized there must be another problem. In my opinion, you should try to use the scanner with another program. As far as I know, you can also use Microsoft word and try to import image from a scanner. If Office is installed on your device, try to import something in the word document.

  Good bye

• Not able to remove the USB stick while Labview is open

  For all the gurus.

  I'm using LabView 8.5 and made an Application that requires the user to download the data of the disc/USB. Then, when VI works user invited to select a. TXT from USB to download file. Here, the entire operation ends as desired. Only ONE PROBLEM I am facing is when download completed attempts to the user to 'remove the USB' where gives windows a warning saying USB is in use and cannot be deleted.

  This particular VI I use function of file dialog box to browse USB and let the user select a file. I even tried to use the function to open the file, but it gives same error.

  The only way I can pull out USB after the download is out of Labview which is not feasible for my application.

  is this a Bug in 8.5 or is there a different way to do it?

  Any help will be appreciated.

  Concerning

  You can call the Windows API SetCurrentDirectory function (see attachment), but if you follow the link you will see it warns about its use in multithreaded applications. I have no experience with it, so I can't comment.

• Installation of the USB 2.0 extension cable failure, and I am on Windows 7.

  I recently bought a foot 6 ' Male/female' USB extension cable, and it's USB 2.0.
  I bought it because my headphones would not properly work because of a problem in my computer and I thought that an extension can help to stop this problem.
  So, I try to install, but it never does.
  Does anyone know why there are installation problems?
  Also, Yes, the helmet works if I plug it directly on the computer, but with some errors.

  Hi guy,

  I understand that the USB 2.0 extension cable does not work on your computer.

  1. What is Gets the error message when you connect the headphones to the computer?
  2 have you tried plugging the USB cable into another computer?
  3. have you tried it with different USB ports?
  4. What is the brand and model of the computer and a USB headset?
  5. did you of recent changes to the computer?

  Extension cable does not need a driver, this is just a thread. USB cables come in varying degrees of quality. The length of the cable can also be important, because the voltage of the equipment can be reduced by the resistance of the cable. Some devices specify 6 feet or less while others may work correctly with 12 people or more.

  I would suggest trying the following steps and check if it helps.

  Method 1:

  I suggest to run the hardware and devices Troubleshooter and check if it helps.

  Open the hardware and devices Troubleshooter

  
  http://Windows.Microsoft.com/en-in/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2:

  I suggest to open a session on the helmet manufacturer's Web site and install the latest drivers for the headset, if the problem persists.

  You can also check the USB device drivers updated using windows update. See below the help link

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  If the edge of the question persists I'll ask allows you to check the chipset driver updates you find on the manufacturer's website. The chipset drivers normally integrate USB controller drivers as well.

  For more information:

  http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  It will be useful.

  For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

• Best installation of the USB driver of practices for non-persistent clones

  Hello

  are there best practices using non-persistent clones and USB driver?

  Client A connects to a linked clone and connects a drive USB flash or something else.

  The installation of the driver is horrible slow on Windows 7:

  • New device found...
  • looking for a driver in driverstore...
  • installing the driver software...

  Tested now and it took more than 8mins.

  After installation, the appliance is ready and can be used. But after disconnecting from the desktop computer updates and each driver installation must be run again at the next connection. We have disabled the Windows updates and specified do not search Windows Update for device driver locations. (Policies-> models-> system administration / Installation of devices-> search order specified for the device driver source locations).

  Clues, why it is so slowly installing drivers and how to prevent the reinstallation of drivers every day

  Thank you and best regards

  Well,.

  We have set. VA was the problem...

  We excluded analyzes the demand for processes drvinst.exe.

  Thank you

• no internet tv after installation of the usb tv tuner!

  I recently bought a HP laptop g62-228 ca series.

  I had set up the center of windows media, (no problem in doing so).

  I was able to open/Internet t.v and view them (especially short video clips / some full episodes, very crisp clear picture.) a lot of the content could not be considered because I reside in the Canada.

  After installing the usb tv tuner and set up for regular tv viewing with my local cable provider. (no problem with that too).

  I could not open/access channels or videos even as I liked be4 I had installed the tv tuner. I can see them in the Guide and even highlight, but I can't open them.

  If someone can help me solve this problem, so I can return to view internet tv. on my laptop?

  I would be very grateful.

  P. S.

  the tuner, I bought says it supports NTSC; ATSC; & clear QAM.

  poonman61

  Hello

  Unfortunately, Internet TV is not available in the Canada.

  David
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Portege R100 - question about the installation of the USB port and Windows problems

  Hello

  I just bought a used Portege R100, but I have some problems. Of course the laptop isn't a CD or DVD, player so I tried an external DVD drive, but it did not work. What kind of device I have to install Windows (not an edition of recovery or anything like that, but a whole new windows on the formatted HARD drive)?

  I also have another problem: whenever I plug a USB device (I tried the DVD drive external and a USB keyboard) when I start the laptop, it seems to hang. At least, I am not able to type anything more; the keyboard of the laptop is dead (the point where the entrance would still be flashing in the BACK platform, but typing. sth on the keyboard isn't doing anything). It is not normal, is it?

  I also tried to get to the BIOS, but I tried various commands (F1 to F12, DEL etc.), but I couldn't access the BIOS. It would be great if someone could tell me the command for it.

  Thanks in advance for the help and sorry for the bad English, I'm not a native speaker :)

  The forum has a search function, but to help you look still these 2 wires:

  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=19232
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=23921

  Here you can see that XP installation isn't very easy, but can be done successfully

  as long as you are working in an environment with appropriate back-drivers back, you can use any kind of external (USB or pcmcia) CD player you want

  the bios is accessible by pressing ESC and the Start button

• Is it possible to operate the USB TC-01 Labview 7.0 Express?

  I have the device of thermocouple USB TC-01. I installed DAQmx 9 and is recorded in «Devices and Interfaces» However, the sample code provided is written in Labview 8.1 and I'm under 7.0Express - is it possible to run in 7.0 (I can't find a vi to interface with it)? If so, someone has the code example and/or can convert the code example to 7.0? Thanks in advance

  Paul

  The latest version of DAQmx for LabVIEW 7.0 is the version 8.1. The Readme for 9.0 also claims that the 7.0 is not supported.

  Good reason to finally make a long delay LabVIEW upgrade.

• Installation of the USB Modem problem

  I am trying to install a Telstra 4 G mobile USB modem on a Dell Ultrabook on Windows 7, keep this message ' VB Script run time for custom action ' won't complete installation

  Update your Windows and install the latest update.

  Visit the website of support if your modem and install the latest version of the driver.

  Contact the manufacturer support and discuss this matter with them.

• Installation of the USB-6211 for DA

  I try to use a USB-6211 housing in a very simple system of Visual Studio C++. The final goal is to continuousely output for both channels to 180 samples per second. At this point, I have the following Setup:

  DAQmxErrChk (DAQmxCreateTask("",&taskHandle));
  DAQmxErrChk (DAQmxCreateAOVoltageChan (taskHandle,
  devcmd, //physical channel
  ' ', //name assigned.
  -10.0, the production of //min value
  10.0, output value of //max
  DAQmx_Val_Volts, release //units
  "" scale //custom name
  ));
  DAQmxErrChk (DAQmxCfgSampClkTiming (taskHandle,
  "", //source (default OnboardClock)
  180.0, //rate in the samples per second
  DAQmx_Val_Rising, //active edge
  DAQmx_Val_FiniteSamps, finite number of samples (to change) //a
  samples_to_write //samples to acquire
  ));
  DAQmxErrChk (DAQmxStartTask (taskHandle));

  On the last drive, I get the message:

  Non-bufferered of NI by the equipment operations are not supported for this device and the type of channel. I can't make any sense of it. Any suggestions?

  One of your support staff helped on the phone. It appears as a somewhat obscure command

  DAQmxSetWriteRegenMode (taskHandle, DAQmx_Val_DoNotAllowRegen)

  It takes to get buffering to work properly. It is a command badly documented, and there is no real indication that this is necessary.

• Publish with the installation of the USB SFD 321U/HP floppy drive.

  Can someone help me: I have an old USB SFD 321U/HP floppy drive and would like to find a driver for my Windows 7 to this regulation.

  Install a NEC USB Floppy driver and it will work in Windows 7 64 bit. Worked for me.

  Details are here: http://www.techgeekandmore.com/2009/12/11/hardware-getting-the-iomega-usb-floppy-drive-to-work-with-windows-vista-and-windows-7/

• Installation of the USB

  How are things at the minute. Connected a HDD IDE adapter USB to a Tin running with the intention to install win7. Got a message that says "unable to install USB. Perhaps the bios how the * do get around this? TY

  Windows 7 can be installed from a USB drive, but not on a drive connected by USB.

  Motherboard sees your drive (IDE) as it is connected through USB.

• DeskJet 1510 all-in-One: the installation of the software has failed after the USB connection and remain unfinihed. Work for printer and Scanner

  My PC Dell XPS401L has been updated to Win 7 Win 10.  Then, the HP DJ1510_188 software has been installed.

  The task was ok until the bond required of the Dekjet to the USB port.

  Heard the noise of the acknowledgement of receipt, but there screen remains unchanged despite I wait several minutes. So the installation remains unfinished. However, the printer and scanner are both of the device but are not available important "Solution Center" screen.  I already have the solutions of the error indicated by HP support withot success.

  The system indicates that the problems appear in the USBsetup.exe

  Can someone help on this subject?

  Horacio

  Hi @Horacio_B,

  Thanks for joining the Forums of HP Support for a solution to your installation problem.

  I understand that you try to use an all-in-one printer HP Deskjet 1510 with a PC that has been upgraded from Windows 7 to Windows 10 but does not complete the installation of the USB and the HP Solution Center is not available. I would like to help.

  I would like to start by disconnecting the USB cable and uninstall all software related to printers. Here is a support document which can be used if necessary reference - uninstalling the software of the printer (Windows).

  Once it's over try to use the HP printer installation wizard for installation. This tool will get the software and installation help.

  Please let me know if that solves the problem, or if you need assistance.

  Indeed, if this help you to achieve a solution please click the 'accept as Solution' and the 'thumbs up' buttons down below in this message.

  Thank you!