instrument driver

I tried to connect TEC-9100 to Labview, but I couldn't find the right driver. I haven't tried any in IDN no chance.


Tags: NI Software

Similar Questions

  • SMU Chassis or modules appearing does not in NI Instrument Driver Finder/connecte Intstruments

    New user, to debut with a chassis SMU-1073, controlled by a PC, with supply POWER 4113, 4145 SMU and 4071 modules DMM.

    I installed all the drivers from the supplied USB system and I can indeed see/control of the chassis and modules of NI MAX.

    When I try to see the modules Labview 2012 or 2014 (I'm looking for example VI to start) Instrument Driver finder does not show any chassis or modules.

    Looking for support OR but could find no generic "Here's how to start using this box OR $20,000 without flinching" first steps to help.

    So, I was hoping that it was a mistake and plug and play like the other instruments I connected and used. What I am doing wrong?

    Do not use the finder of the instrument. Use the help > examples of find and refer to material input and output. Be specific in listing of the drivers you have installed.

  • How can I specify VISA as the interface of the wizard of IVI instrument driver?

    After a long hiatus and to reinstall on a new hard drive, I resumed an IVI driver development. Previously, when I experienced, I was able to generate a driver that uses the API of VISA.

    Now, on this new installation, when I start the wizard, the only choices I have are Gbspecifications FOR, serial and VXI (message and registry).

    How can I specify VISA?

    Hey Frog,

    As this measure Studio LabWindows/CVI Instrument Driver Developer Guide , VISA i/o interface is the mechanism through which the pilot communicates with the hardware of the instrument. The IVI Instrument Driver Wizard allows you to only select among GPIB, VXI and series more specify the interface for your instrument.

    I hope this information helps!

  • Find the instrument Driver won't find 6070E vi

    I have trying to find vi that have been written for card PXI-6070E.  Some fundamental, as output 1 V out of the DAC1OUT.

    When I use "Find her Instrument Driver"... and interrogate National Instrument (company) and 6070E (additional keywords) I get no driver?  I remember being able to get to drivers before.

    Can someone help me please?

    Thank you

    Find the tool instrument Driver is for drivers of finding for instruments like scopes, DMM, power supplies, etc. The PXI - 6070E is a data acquisition card, so the examples it would be installed when you install the DAQmx drivers. You can find the examples in the example Finder (help-> find examples) and search for "DAQ" or see material input and output-> DAQmx folder in the menu tree.

  • Instrument driver management

    Hi all

    I use Labview 2013 and later to drive various instruments of laboratory, including power supplies, multimeters, generators, etc. of signals. The Labview drivers are located on the Web site of OR or the provider. However, since I use a lot of different instruments, how can I get the latest driver for way better to go to the websites and to constantly check?

    Is there something like JKI instrument drivers?

    Thanks for letting me know.

    Really expected to update you your instrument drivers under one of the three circumstances:

    1. you have a problem with your instrument, data, or program that you can trace back to a bug in the driver

    2. your instrument has its updated firmware to update or you buy a newer version and the newer version/firmware does not work with your existing driver more

    3. you have updated your version of LabVIEW and the old drivers no longer work

    I know that during the debugging of generic or just PC problems PC maintenance it is always a good idea to update your drivers for your various pieces of hardware, but it must be remembered that most of the LabVIEW drivers are not really in the traditional sense device drivers, Windows device drivers are , but are rather wrappers around communication protocols IVI/VISA/etc which have predetermined commands all facts for you.

  • project style instrument driver

    Hi all

    1. What is the advantage or the importance of the project-style Instrument pilot pilot instrument type LLB?

    2. in the event that the project file be located in the directory "C:\Program NIUninstaller Instruments\LabVIEW 8.0\instr.lib"?

    (My problem is if I use the driver to a location other than the mentioned directory, all the screws that are related to the trace showing C:\Program NIUninstaller Instruments\LabVIEW 8.0\instr.lib\Chroma ATE 6310)

    Please find the picture as an attachment.

    Can someone explain why this happens?

    Thank you

    Davidson

    Hi Nathan,

    Thanks for the useful link. Cool

    So if I need to get rid of the cross-connection, I need ( manually download) copy the driver to the C:\Program NIUninstaller Instruments\LabVIEW 8.0\instr.lib"directory.

    Thank you

    Davidson

  • Impossible to select and place the Instrument Driver VI icons on the block diagram

    I am trying to automate some of the RF measurements using a Rohde and Schwarz Spectrum Analyzer. I downloaded the Rohde and Schwarz spectrum analyzer pilot named 'rsspecan' version 2.6.1 for Labview on Rohde and Schwarz site to use in my version of the software labview 7.1.

    I copied the files in the appropriate folders in the Labview software on the C drive files. I am able to access those files through the functions---> Instrument I / O---> range of Driver of instruments in the Labview diagram, but when I select the VI icon that I want to put, I am unable to place it on the block diagram. Instead of hovering under the cursor by clicking on the VI icon, by clicking on the icon of the VI has no answer whatsoever.

    Any help would be greatly appreciated.

    Thank you

    Thank you very much for the help.

    So, is there a way to get the above mentioned pilot online Spectrum Analyzer, which will be also compatible with LabVIEW 7.1, so that I don't have to go through the conversion of version Board?

    Thanks again,

    Vivek

  • How to make an instrument driver appear in the Toolbox tools

    Hello

    I created an instrument using driver to create a new instrument pilot project.  I have all the screws in place in the project and saved all, library and all in the instr.lib folder and have restarted labview and the screws are still not showing upward under instrument of e / s--> option instrument drivers.  could you please go on the process someone or just tell me what I might be missing to have these drivers appear in the Toolbox tools!

    Thanks for the help,

    Brent schenk

    In the Start Menu get > Browse

    In the create new window > project > project of the magician > Instrument pilot project

    Select the new driver model

    Select the type of instrument you have

    Click next

    * Make sure that the location of the project is correct. I think that's where you're wrong.* *.

    It should say something like: C: / / Program Files / National Instruments/LabVIEW 8.5/instr.llb/yourproject/yourproject.lvproj

    If you have the correct directory, it should appear in the library of instruments

  • With the help of NOR-5641R with FPGA and the instrument driver


    Hi Ran,

    I don't think what you describe is possible for two reasons.

    1. You cannot run the pilot bitfile instrument at the same time as a user defined FPGA bit file

    2. AO ports are AC coupled, so you will not be able to generate a DC bias on them.

  • possible bug in Agilent ENA series LabVIEW Plug - and - Play (project-style) Instrument driver

    think I found a bug in this driver and I wanted to get confirmation.  (Here's the link to the driver page, to help locate the driver):
    ( http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=74D1F1D4EB5268E8E04400144FB7D2...)

    The VI in question is public > Action-status > configure > marker Configuration > Configure Marker.vi.

    The question that I saw was that the marker was not be set to the frequency transmitted to the VI.  (The parameter named 'Stimulus'.)  I looked at the guide to the programmer for the Agilent 5071 B and decided that the format of the SCPI command string should probably:

    %.;:Calc%ld:Mark%ld %s;
    : CALC % ld: % ld MARK: X % lf

    The ": X" had disappeared but seems necessary.

    Can this be verified?

    Thank you for taking the time to look at it.

    -Joel

    Snood1,

    I took a glance at the driver and manual of the programmer. It seems to me that the driver behaves as described in the manual should. Configure the Marker.vi use the following string to format the command:

    %.;:CALC%ld:MARK%ld %s;
    :CALC%ld:MARK%ld:X %lf
    

    Is that what you see too? Looks like that's what you added yourself. What was the previous text? This is the text that was there when I downloaded the driver. When it is interpreted, it looks like this

    :CALC1:MARK1 OFF;
    :CALC1:MARK1:X 0.000000
    

    As described in the ENA series Programmer manual, the first turns of the line of the marker reads OFF (page 283). The second line sets the value of the marker 1 (page 295) stimulation.

    Let me know if this looks OK to you.

    Kind regards

  • HOWTO modify an icon of high level for an instrument driver

    Hello

    using labview 2009 I started a new driver for the device. During the Setup for the driver Wizard, I created an icon of high level. I would like to reuse this icon for the screw in the pilot, but can not understand how to change this icon (or copy it to other screw). For now the only place where I see it's in the library instrumt palette. Any help would be appreciated.

    Thank you

    Arun

    If it's the same as 8.6, go to tools > modify a Palette set. When the palettes open, go to one you want and right-click on it. You have the choice to copy the icon or change.

  • Undesirable gain created by AFG3022 generating function Instrument Driver example VI

    I used the function generator 'Create Standard waveform' example VI of AFG3022. I was able to create a waveform, but the gain of the wave looks like 5 times less on a scope. For example, if I create a square wave 5 Vpp 150KHz through the example of the VI, it resembles a 1Vpp, square wave of 150kHz within my reach. Why is this happening and how can I get rid of gain?

    Is the impedance setting for your game of the scope of the impedance of the probe entry?  I've seen this when the input impedance was not on the scope.

  • Suggestion regarding mitigation of the probe in the instrument Tektronix 7000 Series Driver


    Hello Brian,.

    In the Readme of the instrument under problems driver known:

    To report any questions or comments about this instrument driver, please send an email to [email protected].

    As this is a pilot certified NOR supported it but only R & D can change it.

    Kind regards

    Mart G.

  • Test driver for agilent 8960 for instruments run CDMA

    Hi, just wonder if there is an instrument for agilent 8960 for driver run CDMA tests? I know 8960 has E1963 and E1968, but 1963 is designed for W-CDMA and GSM/GPRS/EGPRS 1968. So there is a driver designed for CDMA mode? Thank you very much!

    Unfortunately, it is not that there is currently a.  When I search the Instrument Driver Network, I can't find that both pilots that you pointed out.

    Brandon Treece

    Technical sales engineer

    National Instruments

  • Looking for Driver of instruments Boonton 9242

    I'm looking for an instrument driver for a voltmeter of RF Boonton 9242. Any help is appreciated!

    Is this consistent SCPI instrument? If so you don't necessarily need drivers for the exact model.

    SCPI defines interfaces for several types of instruments - including voltmeters.

    Mike...

Maybe you are looking for

  • most recent software problem

    I just my iphone has been installed the latest version, but it comes out I can't use the search engine on the top (safari). Can someone explain what is happening and what is the solution?

  • Bug found during the use of references to the control in subVis on Compact RIO?

    Hallo, I have a simple task. I want to read higher VI into a Subvi the real value of a control to a level. I want to solve this problem by using a reference to the control. I have attached a simplified program that shows this. But the problem is now.

  • DeskJet all in a single 2542

    I need help find a software for my printer disk. I need the button print, I can bring up and use when I can't access the icon at the top of the current page.

  • QWERTZ keyboards sold as a default value in the United Kingdom

    I come on the Dell site to the United Kingdom to buy a new desktop... or so I thought. I found the default keyboard for the office, I was going to buy QWERTZ (instead of QWERTY). Now, I know very well that the QWERTZ is fine for the Germany and that

  • Cursor mess between monitors in a dual configuration monitor

    I have a Setup dual monitor and often when I move my cursor between two monitors using the lower part of the screen the cursor takes the form (usually to something that resembles an eyelash on the side). I can usually force it to change by moving qui