Interesting VPN traffic

Similar Questions

• ASA encrypt interesting VPN traffic

  Hello everybody out there using ASA.

  I had a few IPSEC VPN tunnels between the company's central site and remote sites.

  Two dsl lines were connected to the ASA, one for VPN traffic and the other for the internet.

  The default gateway has been configured online internet, some static while insured roads as traffic to the sites of the company was sent through the other line.

  A few days ago we changed the configuration of ASA to use only a single dsl connection, then the line serving the internet has been cut, while the other will become the gateway default and static routes have been removed.

  The VPN connections instant stopped working and trying to send packets to the remote lan, it seems that ASA will not recognize that the traffic is encrypted. Obviousely we checked cryptomap, acl, ecc, but we find no problem... do you have any suggestions?

  Thanks in advance,

  Matt

  -----------------------------------------------------------------------------------------------------------------------------------------------------------------

  XNetwork object network
  10.10.0.0 subnet 255.255.255.0

  network of the YNetwork object
  172.0.1.0 subnet 255.255.255.0

  card crypto RB1ITSHDSL001_map2 1 corresponds to the address RB1ITSHDSL001_1_cryptomap
  card crypto RB1ITSHDSL001_map2 1 set peer a.b.c.186
  RB1ITSHDSL001_map2 1 transform-set ESP-3DES-SHA crypto card game

  RB1ITSHDSL001_1_cryptomap list extended access permitted ip XNetwork object YNetwork

  -------------------------------------------------------------------------------------------------------------------------------------------------------------------

  Hello

  Your exit the ASA must be encrypting the traffic between XNetwork and YNetwork.

  If the ASA does not encrypt this traffic, it could be because there is a problem with the NAT configuration.

  When the ASA receives a packet, it must first check if there are ACLs that allows traffic, passes through the inspection engine and check that the associated NAT. For example, if the package is coordinated, then the private IP encryption will never take place.

  Could ensure you that packets from the XNetwork are really reach the ASA, the NAT rule is correct and you may be looking for "debugging cry isa 127" and "scream ips 127" debug to check for errors of incompatibility.

  In addition, what is the condition of the tunnel trying to communicate: "sh cry isa his"

  Federico.

• Source of interesting VPN traffic to PIX / ASA

  Is it possible the CLI to interesting to implement traffic source or otherwise test a VPN strategy?

  As far as I KNOW - this is not possible, because you cannot create a tcp/udp/icmp from a source interface in the device.

• 7.2 ASA5520 - filters VPN traffic

  Hi all,

  I would like to know how can I filter out VPN traffic with a list of access, by using the source address and port of destination as filters.

  I tried with "no sysopt permit vpn connection" but it is to filter the traffic through the VPN tunnel and I want to filter the host which can establish the VPN tunnel.

  I did it in a router with this access list:

  Note access-list 101 VPN

  access-list 101 permit ahp host x.x.x.x everything

  access-list 101 permit esp host x.x.x.x any newspaper

  access-list 101 permit host x.x.x.x esp all

  access-list 101 permit udp host x.x.x.x any eq isakmp

  access-list 101 permit udp host x.x.x.x any eq non500-isakmp

  But I tried the same thing in the ASA and does not work, I think it's because the ASA does not apply the access list for VPN traffic.

  Sincerely, Fernando.

  Fernando

  You can disable it with "no crypto isakmp are outside", but then even if you apply an acl to the outside which allows all IP, ESP, AH it still does not allow an IPSEC connection.

  So for the moment I see no way to do this without using an acl on your router upstream.

  I'll do a reading just in case I missed something.

  Jon

• Capture packets for VPN traffic

  Hi team,

  Please help me to set the ACL and capture for remote access VPN traffic.

  To see the amount of traffic flows from this IP Source address.

  Source: Remote VPN IP (syringe) 10.10.10.10 access

  Destination: any

  That's what I've done does not

  extended VPN permit tcp host 10.10.10.10 access list all

  interface captures CAP_VPN VPN access to OUTSIDE gross-list data type

  Hello

  If you have configured capture with this access list, you filter all TCP traffic, so you will not be able to see the UDP or ICMP traffic too, I would recommend using the ACL, although only with intellectual property:

  list of allowed extended VPN ip host 10.10.10.10 access everything

  Capture interface outside access, VPN CAP_VPN-list

  Then with:

  See the capture of CAP_VPN

  You will be able to see the packet capture on the SAA, you can export the capture of a sniffer of packages as follows:

    https:// /capture//pcap capname--> CAP

  For more details of capture you can find it on this link

  Let me know if you could get the information that you were trying to achieve.

  Please Don t forget to rate and score as correct the helpful post!

  David Castro,

  Kind regards

• NAT on the VPN traffic

  Hello everyone, I need help in a vpn configuration, this is the problem that I need nat all vpn traffic because I net to put into place a vpn but I already have another vpn with the same network, so that overlap with the new one, then how I can nat overlaps all traffic to another network in order to avoid the network?.

  Please I really need help

  Thank you

  You say that the 192.168.1.100 is able to go through the tunnel and the internet now?

  Try to add another...

  IP nat inside source static 192.168.1.101 10.10.44.101 map route VPN

  for example.

  Federico.

• Configuration of the router to allow VPN traffic through

  I would like to ask for assistance with a specific configuration to allow VPN traffic through a router from 1721.

  The network configuration is the following:

  Internet - Cisco 1721 - Cisco PIX 506th - LAN

  Remote clients connect from the internet by using the Cisco VPN client. The 1721 should just pass the packets through to the PIX, which is 192.168.0.2. Inside of the interface of the router is 192.168.0.1.

  The pix was originally configured with a public ip address and has been tested to work well to authenticate VPN connections and passing traffic in the local network. Then, the external ip address was changed to 192.168.0.2 and the router behind.

  The 1721 is configured with an ADSL connection, with fall-over automatic for an asynchronous connection. This configuration does not work well, and in the local network, users have normal internet access. I added lists of access for udp, esp and the traffic of the ahp.

  Cisco VPN clients receive an error indicating that the remote control is not responding.

  I have attached the router for reference, and any help would be greatly apreciated.

  Manual.

  Brian

  For VPN clients reach the PIX to complete their VPN the PIX needs to an address that is accessible from the outside where the customers are. When the PIX was a public address was obviously easy for guests to reach the PIX. When you give the PIX one address private, then he must make a translation. And this becomes a problem if the translation is dynamic.

  You have provided a static translation that is what is needed. But you have restricted the TCP 3389. I don't know why you restricted it in this way. What is supposed to happen for ISAKMP and ESP, AHP traffic? How is it to be translated?

  If there is not a static translation for ISAKMP traffic, ESP and AHP so clients don't know how to reach the server. Which brings me to the question of what the address is configured in the client to the server?

  HTH

  Rick

• VPN needs access to all external internal vpn traffic traffic all in tunnel

  Hello

  Could someone help me find the problem?

  I am ASA configuration as firewall + vpn server, essentially outside of the device's access T1 (there are two VLANS in inside via an iptables, outside of iptables is on the same vlan as insdie of ASA (192.168.5.1 and 192.168.5.2).)  VPN users are authenticated via authentication 2 factors (SDI, ip is 192.168.5.5) and get the ACL by local database.  pool of VPN is 192.168.6.1 - 192.168.6.15. pool of VPN is coordinated to the external IP address

  trying to access a remote host A from the host a is open for the IP and one specific Protocol. all vpn traffic are in the tunnel. the VPN user can connected and ACL vpnuser1_ONLY not working does not as expected.

  Here is the part of configuration:

  ASA Version 8.2 (2)
  ...........

  Route outside 0.0.0.0 0.0.0.0 xx.10.194.193 1

  Route inside companynet1 255.255.255.0 192.168.5.2 1

  Route inside companynet2 255.255.255.0 192.168.5.2 1

  Route inside companynet3 255.255.255.0 192.168.5.2 1

  Route inside companynet4 255.255.255.0 192.168.5.2 1

  ...............

  Route inside companynetn 255.255.255.0 192.168.5.2 1

  
  

  NAT (inside) 4 vpnpool 255.255.255.0 outside   <--------- is="" this="">

  Global (outside) 4 xx.10.194.238 netmask 255.255.255.255

  Split-tunnel-policy tunnelall

  .....................

  vpnuser1_ONLY list extended access permitted tcp vpnpool 255.255.255.0 192.168.1.28 host 255.255.255.255 eq ssh connect

  vpnuser1_ONLY list extended access permitted tcp vpnpool 255.255.255.0 74.2.23.195 host 255.255.255.255 eq ssh connect

  ............

  enable SVC

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  VPN - connections 8

  VPN-idle-timeout 10

  VPN-session-timeout 60

  Protocol-tunnel-VPN l2tp ipsec

  WebVPN

  SVC Dungeon - install any

  time to generate a new key of SVC 8

  SVC generate a new method ssl key

  SVC request no svc default

  internal GroupPolicy1 group strategy

  attributes of Group Policy GroupPolicy1

  VPN - connections 1

  VPN-idle-timeout 9

  VPN-session-timeout 45

  VPN-tunnel-Protocol svc

  Split-tunnel-policy tunnelall

  WebVPN

  SVC Dungeon - install any

  time to generate a new key of SVC 15

  SVC generate a new method ssl key

  client of dpd-interval SVC 30

  dpd-interval SVC 30 bridge

  value of deny message connection succeeded, but because some criteria have not been met, or because of a specific group policy, you are not allowed to use the VPN features. For more information, contact your COMPUTER administrator.

  disable the SVC routing-filtering-ignore

  username vpnuser1 encrypted password xxxxxxx

  username vpnuser1 attributes

  VPN-group-policy GroupPolicy1

  VPN-idle-timeout 6

  VPN-session-timeout 20

  VPN-filter value vpnuser1_ONLY

  VPN-tunnel-Protocol svc

  value of group-lock COMAVPN

  type of remote access service

  tunnel-group DefaultRAGroup webvpn-attributes

  Disable group companyvpn aliases

  type tunnel-group COMAVPN remote access

  attributes global-tunnel-group COMAVPN

  address (inside) vpnpool pool

  address vpnpool pool

  SDI Group-authentication server

  authentication-server-group (inside) SDI

  LOCAL authority-server-group

  Group Policy - by default-GroupPolicy1

  tunnel-group COMAVPN webvpn-attributes

  activation of the Group companyremote alias

  I did anything wrong / missing?

  Thank you

  Yijun

  
  

  First of all, you can set "no nat-control" because once you have relieved of NAT, 'no nat-control' becomes disable anyway. 'No nat-control' is useful if you have no statement of NAT at all on the interface.

  Second, if you can't access the outside inside which is because you must configure the NAT exemption. Not sure if you have configured it.

  Here's the command:

  access-list allowed sheep ip 192.168.1.0 255.255.255.0 192.168.6.0 255.255.255.0

  NAT (inside) 0 access-list sheep

  You can then add all other subnets that are internal to the ACL sheep if you need VPN access.

  Finally, for the error message deny on access-group "OUTSIDE", you would need check if you have configured "sysopt connection VPN-enabled'. If it is disabled, it will also check the "OUTSIDE" interface for VPN traffic.

• VPN traffic via a secondary access provider

  Hello world

  I have been asked by a client to implement this topology:

  

  where:

  ISP 1 is used as primary internet connection.

  2 ISP will be used to connect remote users by IPsec VPN.

  Currently, I'm not looking for the Active/Backup feature, I need to know if I can use both ISP connections (as I've written before) an ISP for the Internet company and the other for the user remote access VPN.

  I read some post where, said, it's possible, but I want to be sure.

  Kind regards

  Jose

  ASA must add the static route in the routing table automatically when the VPN client is connected. So, in general, you don't need to do anything. But if not, you can just manually configure who will forward a VPN client IP packet to ISP2.

  With respect to NAT, in general, VPN traffic must ignore the NAT. You can use "nat (inside_interface_name) 0-list of access ' with an ACL that define the vpn traffic to do so.

• WSA issue with MS-OUTLOOK and VPN traffic

  Hi all

  I am facing a problem where

  1. my users are able to access their mail from the web page, but ms-outlook is not able to synchronize e-mail.

  2. our internal user to an external site via VPN, the user is able to establish the VPN connection, but the web page user tries to gain access to via VPN is not available. I can see traffic from the user to WSA in the firewall, but the traffic of WSA is not forward traffic after that.

  Please suggest. As it is new, I needmore helps everyone.

  Run the command grep in WSA CLI to get the corresponding access logs to see the behavior of the ASO at demand management.

  Grep, access connects for a starter, SSH to the ASO and run the following command from the CLI:

  1 Grep
  2. Enter the number of the journal you want to grep: 1 (for accesslogs)
  3. Enter the regular expression to grep: . *.
  4. do you want the search to be case insensitive? : Y
  5. do you want to tail the logs? : Y
  6. you want to paginate output? : N

  Please keep in mind WSA is passively receiving the traffic and please ensure those kind of traffic will be sent to ASO before confirm us that it of a WSA question or not.

• VPN traffic scanned by CSC

  Site2Ste VPN are configured at the branch offices. Traffic Internet goes through the VPN and the main office. Can the module CSC analysis this traffic?

  Concerning

  Remco

  If the traffic is decrypted before/on the ASA, then Yes.

  Concerning

  Farrukh

• VPN-filer configuration on the VPN traffic

  Hello world

  We set up a site to ipsec with the seller.

  For security reasons we do not want to allow all traffic through the tunnel.

  ASA has 2 interfaces both inside and outside.

  We refuse any one on the external interface ip.

  I have config vpn run ACL to allow traffic on port ssh, icmp through the tunnel.

  Then I applied it under the group policy.

  name of VPN-filter value.

  Need to confirm that I must also allow ipec protocols as esp etc under VPN filter ACL?

  Concerning

  MAhesh

  The vpn-filter is applied to the traffic flowing through the tunnel. You don't need to allow all traffic that 'built' like IKE and IPsec VPN.

  On the SAA, you must also add this traffic to your external ACL is it necessary on IOS routers.

  For the vpn-filter, be aware that the syntax is not

  permit/deny PROTOCOL SOURCE DESTINATION

  It's

  permit/deny PROTOCOL REMOTE LOCAL

  This is relevant when you want to filter traffic from your network to the network of peers.

• Send all VPN traffic and the other end it blocks Internet

  Hello

  I wonder if I can get a RV042 VPN Tunnel to a RV082 and in the RV082 block all traffic on the internet that comes form the computers that are behind the RV042.

  Something like this:

  Remote PC-> RV042-> VPN-> RV082-> firewall RV082 (block internet traffic, allow intranet traffic)

  Thank you very much

  Oliver

  The scenario you describe should be doable with a pair of RV042 and RV082, where all traffic is transmitted by RV042 to RV082. What you need is to configure an access on RV082 rule to deny the RV042 subnet HTTP traffic to ALL (internet).

• VPN traffic routed not when ATM / Dialer interface is up

  I have a 1841 router using a serial port for the T1 and a WIC ATM to ADSL. I want all traffic to the data center of my company to go out to the T1 and all other traffic out of the ADSL connection. There is a VPN connection to the data center which works fine until the ATM/Dialer interface is enabled. The VPN tunnel is created, but no traffic is routed over the VPN. I have attached the router config.

  Jason,

  You can try configurations and make the new test below.

  IP route datacenterLAN 255.255.255.0 serial0/0/0

  IP route datacenterLAN2 255.255.0.0 serial0/0/0

  IP route datacenterLAN3 255.255.255.0 serial0/0/0

  IP route datacenterLAN 255.255.255.0 Dialer1 5

  IP route datacenterLAN2 255.255.0.0 Dialer1 5

  IP route datacenterLAN3 255.255.255.0 Dialer1 5

  Kind regards

  Arul

  * Please note all useful messages *.

• A VPN traffic fall

  We are setting up a asa 5505 with anyconnect. But vpn-pool local traffic network is to be droppped. but the traffic from the inside network to the vpn client is not being deleted. Any help

  Hi [email protected] / * /.

  Can you also clear line 'access-group anyconnect in external interface' bur leave a vpn-filter configuration?

  You can also add a line to deny a whole at the end of each ACL to see which blocks the traffic.

  Best regards.