Intergrated PC NICS can cross PIX

I have several PC with integrated NICs that cannot access the internet. If we replace the NETWORK adapter with a PCI NIC it solves the problem. Anyone know of a reason which could cause such a problem?

What is the MAC address on the built-in maps? What version of the PIX code you run.

There is a bug in the old PIX code where it will not learn MAC addresses in the form 0008.xxxx.xxxx. Bug ID is CSCdt47829 (http://www.cisco.com/cgi-bin/Support/Bugtool/onebug.pl?bugid=CSCdt47829)

Tags: Cisco Security

Similar Questions

  • I have windows vista. I did a system restore. I can restore PIX saved on the backups before recovery was made?

    I have windows vista. I did a system restore. I can restore PIX saved on the backups before recovery was made?

    Hi rich,

    What kind of backup do you have?  If it were a full image backup, restoring them will be difficult unless you restore the entire image.  If it was a normal backup of files and folders, it should be fairly simple.

    Here is an article on the restore procedure: http://www.vista4beginners.com/How-to-restore-files to make sure you do this right.  It's a selective restore of a full or selective backup (not a full restore from a full backup) - but since you did a full backup, it matches your process more closely than would a full restore.

    This is a GREAT article on backup and restore Vista process

    http://technet.Microsoft.com/en-us/magazine/2007.09.Backup.aspx , but he won't go into detail about the restoration process - considering almost as easy, of course.  But it teaches you a lot about what is possible and how to do it.   It also focuses primarily on the full backup process, but he did mention the full backup and restore process as well.

    Here is an article on the advanced use of restoration (during normal restore does not work):

    http://www.mayankraichura.com/post/2009/08/06/Avdvanced-Restore-via-Windows-Vista-Backup-and-Restore-Center.aspx.

    Restore files from a backup
    http://Windows.Microsoft.com/en-us/Windows-Vista/restore-files-from-a-backup

    Back up and restore: frequently asked questions
    http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-and-restore-frequently-asked-questions

    If the above does not help with your problem, then please go to the special Microsoft Forum dedicated specifically to backup issues and problems at the: http://social.technet.microsoft.com/Forums/en-US/windowsbackup/ for assistance from experts by specialists in this field.

    I hope this helps.

    Good luck!

  • How Illustrator can crossed fast? (as 'select the fill - same - color")

    Hello. I have a curious.

    If I want to select objects that same color to fill in the document, I can use the function "select fill - same - color" in Illustrator.

    It's so fast. less than 1 second.

    But, if I want to do in Javascript, I can't do it as fast.

    for (i = 0; i < activeDocument.pathItems.length; i ++) {...}

    If the document has 10,000 items, above script cannot complete in same 60 seconds.

    How Illustrator can crossed fast?

    Is there something else?

    Unfortunately not support Javascript. Only the long long way.

    But you can call an action with the CS6 script: select a path in your scipt and call for action (in which is: select same fill color)

    By the way: you could solve your problem last? (http://forums.adobe.com/thread/1310394)

  • Is there that a limit on how many NICs can be associated with a group of ports?

    So, I have a large box with two onboards and two quad ethernet cards.

    Vswitch0

    port groups

    Service console - vmnic6 vmnic5

    kmkernel - vmnic5, vmnic6

    Vswitch1

    port groups

    VMotion - vmnic4, vmnic0

    Vswitch2

    port groups

    external - vmnic2, vmnic3, vmnic8, vmnic9, vmnic1, vmnic7

    The problem we had was when we grew up the server on the net and took it out of the way now, we noticed servers you access, but not ping. So, we watched the distrabution of ip dhcp and noticed that vmnic1 and vmnic7 did not have an assigned ip address range as the others did.

    So is there a limit vnic for grouping of network cards in a port group?

    Shane

    Welcoem to the Forums - according to the rate maximum config - http://www.vmware.com/pdf/vi3_35/esx_3/r35u2/vi3_35_25_u2_config_max.pdf - number maximum fo physical NIC by vswitch are 32 - ip addresses, you're seein' are discovered by the esx on the physical port, these vmnic connect to.

    If you find this or any other answer useful please consider awarding points marking the answer correct or useful

  • A PIX 501 can connect to a VPN service?

    Can a PIX 501 6.3 (4) establish a VPN to a supplier like www.privateinternetaccess.com?  They claim to support PPTP and L2TP/IPSEC.  If so, how the PIX should be configured?

    Thank you.

    No, none of the networking gear (Inc. ASA) can be configured as PPTP and L2TP over IPSec client client.

    Both are PC or MAC software.

  • PIX 501 10 User License

    Does anyone know if the PIX 501 10 user license will limit the number of users can cross a site to site VPN that ends at the PIX?

    Yes, it does, I encountered a problem with it myself in the past. The page at http://www.cisco.com/en/US/customer/products/hw/vpndevc/ps2030/products_data_sheet09186a0080091b18.html

    It is said "the Cisco PIX 501 license 10 users supports up to 10 simultaneous source IP addresses for your internal network to browse the Cisco PIX 501.»

    In my case what happened is that we had a VPN site-to-site created with a small office that adds a little more employees, everything was going well until the 11 IP address attempted to connect to a resource across the IPSec tunnel. We solved the problem by opting for a 50 user license.

  • can't network updates to install on Windows XP

    I can't get updates for Windows XP - this is an update of the network - and I need help badly because I need this update

    1. There is an update for my Windows XP Professional computer that came.

    2 kB951847x86

    3. I don't know if I will not that is why I ask you

    4. I don't know what is SP3

    5. a couple of days ago

    6 I don't know right now

    KB951847 is an update for .NET Framework 3.5 option . There is a chance that you don't need even!
    SP3 is synonymous with Service Pack 3. If you do not, you ask for trouble. Here's how to determine whether you have:
    Start | Run
    Type
    winver
    Press OK.
    What did he say?
    With regard to this part of your message:
    3. I don't know if I will not that is why I ask you
    Which is in contradiction with what you said in your original post! Specifically, you said that you need this update! But now it seems that you know not whether or not do you.
    As a general rule, you should stay away from OPTIONAL updates. In other words, only install CRITICAL security patches. In case another program may need one of the optional .NET frameworks installed, you can cross that bridge when you get there. In addition to stay away from optional software updates, you REALLY need to stay away from optional hardware updates. More than once these updates of the liquidation interfere with the systems of the people!
    Let's take a look at all your instances of .NET Framework:
    Start | Control Panel | Add or remove programs
    Check the box next to "See the updated". Scroll down. What .NET Frameworks are listed? For what it's worth, these are the ones I have:
    Microsoft .NET Framework 2.0 Service Pack 2
    Microsoft .NET Framework 3.0 Service Pack 2
    Microsoft .NET Framework 3.5 SP1 (it's the one that you have problems with)
    Which do you have?
    Remember that a Service Pack is just a series of updates bundled and some added functionality. As you can see, there are service packs for .NET Frameworks as well as the operating system (Windows XP).
  • can not connect to internet with Quest DSL. Quest DSL support said that the NETWORK adapter is missing

    Original title: can not connect to the internet on a desktop computer Windows XP Prof

    I try to use your older desktop with Windows XP Prof  I use Quest with an ADSL connection and that you have a wireless connection to a laptop.  The office is not wireless. I connected the cable earthnet and quest tell me that I don't have "NIC" on my device manager.  Anyone know how I can receive and install on a computer without internet connection?  Thank you

    L E K, I'm sorry, but I don't know the answers to the other questions. After you enable the NIC, can you check your service manual for an explanation of the other choices? Maybe someone else can answer these questions. Liz.

  • I can't send pictures by using ' send to ' or Snipping Tool.

    I use Vista & Windows Mail.  I don't even no error messages - just about nothing happens.   I can join pix directly to my e-mail in Windows Mail, but they are huge for the recipient.  I want to reduce their first reason I am sending via "send to" or a Snipping Tool method, but none works.   Frustrated.

    FOR INFO. It is a forum for Windows 7, Vista.

    Vista implemented network, electronic mail and to get online
    http://social.answers.Microsoft.com/forums/en-us/vistanetworking/threads

    The option send to only resizes pix a minimum quantity. What is the size of these pix? Add 33% for coding. What is the error message?

    Resize your pix first before trying to send them.

    IrfanView:
    www.IrfanView.com

    PIX Resizer:
    http://BlueFive.pair.com/PixResizer.htm

    Bruce Hagen ~ MS - MVP [Mail]

  • How can I burn a DVD in Windows Media Center with the closed captioning information included?

    I recorded a program in Windows media center.  When I read the program, it displays the closed captioning information.  If I burn a DVD program closed captioning information do not display during playback.  How can I burn the DVD to include captioning?

    Hello
     
     
    1. How do you try to burn the DVD? You have saved the DVD on the desktop (hard drive) or you burnt before you save it to a DVD?
    2. after are burning the DVDs in which application you trying to play?

    I suspect that the captions are already burned in DVD, at this point in time we can cross check if the option is set to display captions.
    To enable or disable subtitles for DVD
    a. on the Windows Media Center start screen, navigate to tasks, click settings, click DVD and then click subtitle.
    b. click the plus (+) and minus (-) buttons to select power off or when cut, and then click Save.
     
    For more information, refer to the article below.
    Show captions or subtitles in Windows Media Center
    http://Windows.Microsoft.com/en-us/Windows-Vista/Show-closed-captions-or-subtitles-in-Windows-Media-Center
    See also the belowl link:

    I hope this helps.

    Thank you, and in what concerns:
    Shekhar S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.
    If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • How can I disable Magnifier Comfort Mouse 3000?

    Just installed on XP X 64 edition PC. Turned on the magnifying glass. Nice, can use it. But it does not turn off. I re - clicked on the red side, nothing done. Impossible to find info on the site.

    XP forums:

    http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP

    Link above is for XP Forums.

    There is a list of the different Forums XP to the link above to help you.

    You get the help you need there.

    Here is the Vista Forums.

    See you soon

    Mick Murphy - Microsoft partner

  • VPN on PIX in VLAN own?

    Sink us our PIX 525 s our VPN service. The PIX is currently give IP addresses to the IP VPN.

    I put this IP address range in its own VIRTUAL LAN? I can a PIX with DOT1Q trunk on the switch?

    You could put the range of client IP addresses in its own VIRTUAL LAN, but make sure you announce this route to your core network, via the static route.

    802-1-q is also supported in 525 platform:

    Virtual-based networks VLAN virtual interfaces

    Provides greater flexibility in the definition of policies of security and global integration in switched network environments supporting the resulting creation of logical interfaces of the IEEE 802 VLAN tags. 1 q and creating security policies based on these virtual interfaces

    Supports multiple virtual interfaces on a single physical interface through trunking VLAN

    Supports several trunks VLAN by Cisco PIX Security Appliance

    Supports up to 10 VLANS on Cisco PIX 525 security equipment

  • Help the Site VPN Site PIX 501

    Hello

    I'm pretty new to PIX firewall, so I hope someone here can help me.

    I have two PIX and try to create a private network virtual between the two PIX. I posted the configs below.

    The problem is that I can ping PIX on a PIX two, but I can't ping the servers behind TWO PIX. On two PIX, I cannot ping PIX ONE or all the servers behind it.

    Any advice would be appreciated.

    Thank you

    PIX 1

    6.2 (2) version PIX

    ethernet0 nameif outside security0

    nameif ethernet1 inside the security100

    hostname TMAXWALES

    domain ciscopix.com

    fixup protocol ftp 21

    fixup protocol http 80

    fixup protocol h323 h225 1720

    fixup protocol h323 ras 1718-1719

    fixup protocol they 389

    fixup protocol rsh 514

    fixup protocol rtsp 554

    fixup protocol smtp 25

    fixup protocol sqlnet 1521

    fixup protocol sip 5060

    fixup protocol 2000 skinny

    names of

    inside_outbound_nat0_acl ip 192.168.254.0 access list allow 255.255.255.0 192.1

    68.1.0 255.255.255.0

    outside_cryptomap_20 ip 192.168.254.0 access list allow 255.255.255.0 192.168.1

    .0 255.255.255.0

    pager lines 24

    interface ethernet0 10baset

    interface ethernet1 10full

    Outside 1500 MTU

    Within 1500 MTU

    IP address outside of *. *.198.139 255.255.255.248

    IP address inside 192.168.254.1 255.255.255.0

    alarm action IP verification of information

    alarm action attack IP audit

    location of PDM 192.168.254.10 255.255.255.255 inside

    location of PDM 192.168.1.0 255.255.255.0 outside

    history of PDM activate

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_outbound_nat0_acl

    NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

    Route outside 0.0.0.0 0.0.0.0 *. * 1.198.137

    Timeout xlate 03:00

    Timeout conn 0 half-closed 01:00:10: 00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 TR

    p 0:30:00 sip_media 0:02:00

    Timeout, uauth 0:05:00 absolute

    GANYMEDE + Protocol Ganymede + AAA-server

    RADIUS Protocol RADIUS AAA server

    AAA-server local LOCAL Protocol

    Enable http server

    http 192.168.254.10 255.255.255.255 inside

    No snmp server location

    No snmp Server contact

    SNMP-Server Community public

    No trap to activate snmp Server

    enable floodguard

    Permitted connection ipsec sysopt

    No sysopt route dnat

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    outside_map 20 ipsec-isakmp crypto map

    card crypto outside_map 20 match address outside_cryptomap_20

    card crypto outside_map 20 peers set *. *.198.138

    outside_map crypto 20 card value transform-set ESP-3DES-SHA

    outside_map interface card crypto outside

    ISAKMP allows outside

    ISAKMP key * address *. *.198.138 netmask 255.255.255.255 No.-xauth non - co

    Nfig-mode

    part of pre authentication ISAKMP policy 20

    ISAKMP policy 20 3des encryption

    ISAKMP policy 20 chopping sha

    20 2 ISAKMP policy group

    ISAKMP duration strategy of life 20 86400

    Telnet timeout 5

    SSH timeout 5

    Terminal width 80

    PIX 2

    6.2 (2) version PIX

    ethernet0 nameif outside security0

    nameif ethernet1 inside the security100

    hostname tmaxbangor

    domain ciscopix.com

    fixup protocol ftp 21

    fixup protocol http 80

    fixup protocol h323 h225 1720

    fixup protocol h323 ras 1718-1719

    fixup protocol they 389

    fixup protocol rsh 514

    fixup protocol rtsp 554

    fixup protocol smtp 25

    fixup protocol sqlnet 1521

    fixup protocol sip 5060

    fixup protocol 2000 skinny

    names of

    permit 192.168.1.0 ip access list inside_outbound_nat0_acl 255.255.255.0 192.168

    . 254.0 255.255.255.0

    permit 192.168.1.0 ip access list outside_cryptomap_20 255.255.255.0 192.168.254

    .0 255.255.255.0

    pager lines 24

    opening of session

    debug logging in buffered memory

    interface ethernet0 10baset

    interface ethernet1 10full

    Outside 1500 MTU

    Within 1500 MTU

    IP address outside of *. *.198.138 255.255.255.248

    IP address inside 192.168.1.1 255.255.255.0

    IP verify reverse path to the outside interface

    IP verify reverse path inside interface

    the IP audit info action alarm reset drop

    reset the IP audit attack alarm drop action

    location of PDM 192.168.1.0 255.255.255.0 inside

    PDM logging 100 information

    history of PDM activate

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_outbound_nat0_acl

    NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

    Route outside 0.0.0.0 0.0.0.0 *. * 1.198.137

    Timeout xlate 03:00

    Timeout conn 0 half-closed 01:00:10: 00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 TR

    p 0:30:00 sip_media 0:02:00

    Timeout, uauth 0:05:00 absolute

    GANYMEDE + Protocol Ganymede + AAA-server

    RADIUS Protocol RADIUS AAA server

    AAA-server local LOCAL Protocol

    Enable http server

    http 192.168.1.0 255.255.255.0 inside

    http 192.84.7.111 255.255.255.255 inside

    http 192.168.1.10 255.255.255.255 inside

    No snmp server location

    No snmp Server contact

    SNMP-Server Community public

    No trap to activate snmp Server

    enable floodguard

    Permitted connection ipsec sysopt

    No sysopt route dnat

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    outside_map 20 ipsec-isakmp crypto map

    card crypto outside_map 20 match address outside_cryptomap_20

    card crypto outside_map 20 peers set *. *.198.139

    outside_map crypto 20 card value transform-set ESP-3DES-SHA

    outside_map interface card crypto outside

    ISAKMP allows outside

    ISAKMP key * address *. *.198.139 netmask 255.255.255.255 No.-xauth non - co

    Nfig-mode

    part of pre authentication ISAKMP policy 20

    ISAKMP policy 20 3des encryption

    ISAKMP policy 20 chopping sha

    20 2 ISAKMP policy group

    ISAKMP duration strategy of life 20 86400

    Telnet 192.168.1.0 255.255.255.0 inside

    Telnet timeout 50

    SSH timeout 5

    Terminal width 80

    Can't see anything obviously wrong with the configs. You have these connected back to back on the same subnet, it looks that it even if you have xxx out IP addresses? If so it's maybe a routing problem, in what they send everything to the default gateway of xxx.x.198.137 rather than to the other.

    Try to add a static route to the remote subnet to each PIX that points directly to the peer, so on PIX1 you should have:

    Route outside 192.168.1.0 255.255.255.0 xxx.x.198.138

    and on PIX2 do:

    Route outside 192.168.254.0 255.255.255.0 xxx.x.198.139

    and see if that makes a difference. Note that you wouldn't encounter this problem when these two PIX is on separate networks and uses the default gateway for all routing decisions.

    If this still fails, run 'debug cryp isa' and ' debug cry ipsec "on the two PIX are trying to build a tunnel again, and then and send us the output.

    Also, make sure your tests that you're rattling to a host behind a PIX to a host behind the other PIX, ping PIX to PIX or host because of PIX that won't test your VPN connection.

  • LAN &gt; PROXY &gt; PIX &gt; &gt; &gt; Internet. How?

    Hello

    We use PIX 515E (and we are satisfied), but now I need Activate Proxy Server with some restrictions (user can´t download files .exe etc.).

    Current setting: user has in Internet Explorer (for example) on the connection setting is checked "use proxy server" (192.168.1.151, port 3128) and all restrictions are applied successfully. BUT: If the user uncheck this setting - it can connect to the internet and no restrictions are applied on him - he can download whatewer he wanted.

    On the old version of firewall (kerio winroute 4.2.5) I can put the packet filter rule, and only the user who put the proxy can connect to the internet.

    Can you help me how I can configure PIX?

    Thank you, Milan

    Hello.. as the internal DNS is 192.168.1.2, you must allow access to this IP to talk to the DNS servers of the ISP.

    access your lists looks like this:

    access-list outbound01 permit udp host 192.168.1.2 host 194.228.2.1 eq 53

    outgoing access list permit udp host 192.168.1.2 host 194.228.2.61 eq 53

    outbound01 list of access permit tcp host 192.168.1.151 all http eq

    outbound01 list of access permit tcp host 192.168.1.151 all https eq

    make sure you nat the 192.168.1.2 host out.

  • I'm trying to implement the discoloration of the music (you know when a song fades to another it fades) in windows media player that you can in Windows Vista. Is this something they have taken away from Media Player?

    Help, please

    Hi garykholden,

    Thank you for visiting Microsoft Answers.

    Windows 7 is Windows Media Player default 12. You can cross fade music in Windows Media Player 12 as well.

    Press the Alt key to display the menu bar, then go to view menu to select improvements in the menu dropdown. The next option to highlight are:

    · Fade-chained volume and auto leveling.

    Another method to display enhancements menu in WMP12 is to click on the list on the upper right to display the playlist, and then click the button at the end of the Playlistpane and then go to enhancements menu item to display all the options available.

    Kind regards
    Amal-Microsoft Support.
    Visit our Microsoft answers feedback Forum and let us know what you think.

Maybe you are looking for

  • Contact accidentally deleted on my Mac

    Hello community, I accidentally deleted all my contacts on my Mac, is there a way to recover?What is strange, is that other devices (iPhone) I still have my contacts. I tried to uninstall and reinstall it but without success so far. Thanks for your h

  • HPE HP8 1360t DVI connections and two monitors

    I recently bought a new HP8 HPE 1360t directly from HP. I finally got around to get set up last night. I like almost everything about it, EXCEPT to try to figure out how to make it work with two monitors. Before buying, I contacted HP sales to confir

  • Mount Dev device as network drive does not

    I mounted the unit alpha as a network drive in Windows since the first day and all of a sudden, it doesn't connect. Someone knows how to get it is up again?  I use the same method as the Playbook of editing.

  • Problem with counterfeit report.

    I was badly sold a developer as a home license license. When I spoke to the MS support told me to submit a counterfeit report. I have done this and received an email asking me to send a bunch of stuff that I did not (DVD counterfeit, etc.). I am told

  • Connection to DPS link does not work.

    I tried to connect to DPS to indesign using my Adobe ID, but whenever I click on 'SIGN IN', the link does nothingI have re-installed InDesign CC but still do not work.Allowing this to work fine until in the last days – please help!Thank you.