InterVLAN routing for S4810 VLT

Hello

I just want to clarify things because I get confused all intervlan routing if it is possible to implement if I used VIDEO Lottery devices

First of all when I configured the VLT field in sweetheart two switches (S4810), I need to have an itinerary for my VLAN

-what I used intervlan routing is my favorite, but when the peer routing, active in VLT intervlan routing is applicable or supported in routing peers. ?

-also all configurations of the two peer switches must be identical or same

  • example: when I configured intervlan routing in Peer-1, also, I need to configured intervlan routing in Peer - 2

I want to have an answer if I need intervlan or OSPF configuration with this problem

Thank you very much

BRENT

This technical guide I think answer all your questions. Yes, you can have VLAN routing enabled on the switches. The guide goes through many examples, including examples of switches that is configured to perform the VIRTUAL LAN routing. It also includes examples of configuration that you can use as a reference.

http://Dell.to/1wfDl3n

Let us know if this helps out.

Tags: Dell Switches

Similar Questions

  • LRT214 InterVLAN routing databases

    Could someone understand me, what "InterVLAN Routing" setting (under management port > 802 1 q LAN) actually did or influence?

    It's a bit tedious to find trying and the manual, which is essentially a textual serialization of interfaces Web (kind of pointless), doeosn can't help much.

    It is just a shortcut for firewall access rules, or influence it something else? I can get between the VLANS with access for people with disabilities, and appropriate rule set. However, I have however a strange behavior.

    Anyone know?

    Firewall access rules can override the settings of the inter-VALN. Without the two access rules, hosts VLAN1 will not be able to access hosts in VLAN8 and vice versa.

  • InterVLAN routing problem

    Hi friends,

    I have a question related to the Inter-VLAN routing. I have 2 switch a 3850 L3 and another is 2960 L2 (Pure L2). I even vlan on both switches and IP routing enabled on switch L3. But not woking switch l3 to L2 Intervlan Routing switching systems.

    Configuration as below:

    L3 switch:

    hostname L3

    !

    IP routing

    !

    pvst spanning-tree mode

    !

    interface FastEthernet0/1

    switchport access vlan 7

    spanning tree portfast

    !

    interface FastEthernet0/2

    !

    interface FastEthernet0/3

    !

    interface FastEthernet0/4

    !

    interface FastEthernet0/5

    !

    interface FastEthernet0/6

    !

    interface FastEthernet0/7

    !

    interface FastEthernet0/8

    !

    interface FastEthernet0/9

    !

    interface FastEthernet0/10

    !

    interface FastEthernet0/11

    !

    interface FastEthernet0/12

    !

    interface FastEthernet0/13

    !

    interface FastEthernet0/14

    !

    interface FastEthernet0/15

    !

    interface FastEthernet0/16

    !

    interface FastEthernet0/17

    !

    interface FastEthernet0/18

    !

    interface FastEthernet0/19

    !

    interface FastEthernet0/20

    !

    interface FastEthernet0/21

    !

    interface FastEthernet0/22

    !

    interface FastEthernet0/23

    !

    interface FastEthernet0/24

    Are connected to the L2 switch

    switchport trunk encapsulation dot1q

    switchport mode trunk

    !

    interface GigabitEthernet0/1

    !

    interface GigabitEthernet0/2

    !

    interface Vlan1

    no ip address

    Shutdown

    !

    interface Vlan2

    IP 1.1.1.1 255.255.255.0

    !

    interface Vlan3

    3.3.3.3 IP address 255.255.255.0

    !

    interface Vlan4

    4.4.4.4 IP address 255.255.255.0

    !

    interface Vlan5

    5.5.5.5 IP address 255.255.255.0

    !

    interface Vlan6

    6.6.6.6 IP address 255.255.255.0

    !

    interface Vlan7

    7.7.7.7 IP address 255.255.255.0

    !

    interface Vlan8

    8.8.8.8 IP address 255.255.255.0

    !

    interface Vlan9

    9.9.9.9 IP address 255.255.255.0

    !

    IP classless

    -----------------

    The L2 switch configuration:

    !
    hostname SwitchL2
    !
    !
    !
    !
    !
    pvst spanning-tree mode
    !
    interface FastEthernet0/1
    switchport access vlan 2
    !
    interface FastEthernet0/2
    !
    interface FastEthernet0/3
    !
    interface FastEthernet0/4
    !
    interface FastEthernet0/5
    !
    interface FastEthernet0/6
    !
    interface FastEthernet0/7
    !
    interface FastEthernet0/8
    !
    interface FastEthernet0/9
    !
    interface FastEthernet0/10
    !
    interface FastEthernet0/11
    !
    interface FastEthernet0/12
    !
    interface FastEthernet0/13
    !
    interface FastEthernet0/14
    !
    interface FastEthernet0/15
    !
    interface FastEthernet0/16
    !
    interface FastEthernet0/17
    !
    interface FastEthernet0/18
    !
    interface FastEthernet0/19
    !
    interface FastEthernet0/20
    !
    interface FastEthernet0/21
    !
    interface FastEthernet0/22
    !
    interface FastEthernet0/23
    !
    interface FastEthernet0/24
    switchport mode trunk
    switchport nonegotiate
    !
    interface GigabitEthernet0/1
    !
    interface GigabitEthernet0/2
    !
    interface Vlan1
    no ip address
    Shutdown
    !
    interface Vlan2
    1.1.1.2 IP 255.255.255.0
    !
    interface Vlan7
    IP 7.7.7.8 255.255.255.0
    !

    -------------------

    Note: I do not have any router.

    When I test the same setting on packet tracer then get error:

    1. the destination IP address is not the broadcast address, and it does not match the IP address of the port. The appliance ignores the packet.

    Please resolev question:

    Kind regards.

    Deepak Kumar

    I think that Reza questions 3 and 4 are more important than questions 1 and 2, but perhaps do not go quite far enough. The two switches to assign certain ports to a vlan specific and use the vlan by default for most of the ports. There are no statements on a switch which create the vlan but only statements that a port must Access a specified VLAN

    interface FastEthernet0/1

    switchport access vlan 7

    On some versions of switches that may be enough to create the vlan, but on other switches, it is necessary to create the vlan before using it. Maybe something like

    VLAN 7

    name server_vlan

    I would ask if the VLAN on each switch existence?

    There is another question in this config. The switches have created more than 3 VLANs (vlan 1 - the vlan by default and vlan 2 and vlan 7.) But the L3 switch configured more than one interface vlan (3, 4, 5, 6, 8, 9). Without a vlan underlying pertaining to these layer 3 interfaces vlan will not work.

    HTH

    Rick

  • [SOLVED] Problem with the ACB and InterVLAN routing

    Hello.

    I have Cisco 3750 G with IOS k9 - mz.150 - 2.SE4 Service of intellectual property. In my network, I have 4 VLANs with 4 internet gateways. I have set 4 static route for each gateways and with PBR to match this static routes. If I use "set ip next-hop" all traffic goes through the specific gateway interVlan routing does not work (I need to because the customers interVlan routing in different VLANS must be), and if I use 'set ip default next-hop', I was incapable of it attributed to Vlan (road-map lan14 not supported based on routing strategies).

    Model SDM is on the road that ip Routing is enabled.

    Here is my config for 2 of these VLANS:

    interface Vlan7
    IP 192.168.7.254 255.255.255.0
    IP access-group 107 to
    !
    interface Vlan14
    IP 192.168.14.254 255.255.255.0
    IP access-group 114 to
    !
    IP http server
    IP http secure server
    !
    !
    IP route 0.0.0.0 0.0.0.0 192.168.70.254
    IP route 0.0.0.0 0.0.0.0 192.168.140.254
    !
    access-list 107 permit udp any eq bootpc any eq bootps
    access-list 107 allow ip 192.168.7.0 0.0.0.255 any

    access-list 114 permit udp any eq bootpc any eq bootps
    access-list 114 allow ip 192.168.14.0 0.0.0.255 any

    lan7 allowed 10 route map
    corresponds to the IP 107
    IP 192.168.70.254 jump according to the value
    !

    lan14 allowed 10 route map
    corresponds to the IP 114
    IP 192.168.140.254 jump according to the value

    !

    Where is my error in config?

    Please help me, I'm stuck here almost three weeks.

    Hello

    You have created courses 2-card to set the next hop for a portion of the traffic classified with an acl.

    If you want any other traffic manager you must create an empty instance of your roadmap

    Example:

    lan7 allowed 10 route map

    football game...

    map of route allowed lan7 20 ==> Add this instance and leave it empty. You say the switch/router that he must refrain from other traffic but nothing to apply.

    Hope that this clear.

  • No "ip Routing" command on the switch and still intervlan routing.

    Hello

    In my companies 4500 switch I see there is intervlan routing configured for 4 VLANS there but I don't see any command "ip Routing" on this subject

    to enable routing on the switch. A switch can route the same if the command is not there?

    Ninja,

    Default configuration options often do not appear in "show run".  Please try «performance see all»

    Kind regards

    Christopher

    PS your switch and device business, not small business.

  • Cisco SG300 / ASA 5505 intervlan routing problem

    Dear all

    I have a problem with the configuration correctly sg300 layer 3 behind the ASA 5505 switch (incl. license more security)

    The configuration is the following:

    CISCO SG300 is configured as a layer 3 switch

    VLAN native 1: 192.168.1.254, default route ip address (inside interface ASA 192.168.1.1)

    VLAN defined additional switch

    VLAN 100 with 192.168.100.0/24, default gateway 192.168.100.254

    VLAN 110 with 192.168.110.0/24, default gateway 192.168.110.254

    VLAN 120 with 172.16.0.0/16, default gateway 172.16.10.254

    Of the VLANS (100,110,120) different, I am able to connect to all devices on the other VIRTUAL local networks (with the exception of Native VLAN 1; is not the ping requests)

    From the switch cli I can ping my firewall (192.168.1.1) and all the other gateways of VLANs and vlan (VLAN1, 100, 110, 120) devices

    Asa cli I can only ping my switch (192.168.1.254) port, but no other devices in other VLAN

    My question is this. What should I change or installation in the switch configuration or asa so that other VLANs to access the Internet through the ASA. I will not use the ASA as intervlan routing device, because the switch does this for me

    I tried to change the asa int e0/1 in trunkport (uplink port switch also), to enable all the VLANS, but as soon as I do that, I can not ping 192.168.1.254 ASA cli more.

    Any help is greatly appreciated

    Concerning

    Edwin

    Hi Edwin, because the switch is layer 3, the only necessary behavior is to ensure that default gateways to the computer are set on the SVI interface connection to the switch to make sure that the switch is transfer traffic wished to the ASA.

    The configuration between the ASA and the switch must stay true by dot1q, such as the vlan all other, unidentified native VLAN tagged.

    Also, if I'm not wrong, on the SAA you must set the security level of the port to 100.

    -Tom
    Please evaluate the useful messages

  • Problem of layer 3 of SGE2010 with installing intervlan routing

    I'm new to the switches for small businesses and could use assistance in the configuration of routing for intervlan between several VLANs on the switch. I changed the 3 layer mode and configure the VLAN. When I enter an IP address for VLAN2, I disconnect (VLAN1 ip) configuration on the switch interface and I can't access the switch unless I reset it. I tried several times and each time it has the same. Is there something else I need installation before you configure the ip address for other VLANs?

    Hi Jacqueline,.

    Thank you for your participation in the community of support to small businesses. My name is Nico Muselle of Cisco Sofia HWC.

    This is the normal way for the switch to behave. There are 2 ways to work around this problem.

    1. You assign a port to the VLAN2. After the configuration of the IP address, you connect your PC to this port and make sure that it is in the same subnet as the address IP 2 VLAN.
    2. You assign a static IP address for the vlan by default first and make sure your connected PC is in the same subnet.

    The reason for this behavior is that the switch has its DHCP client enabled, if no DHCP server is available, it will return to its default IP 192.168.1.254 (which I assume that you connect to the configuration).

    However, once you set up a static IP address on the switch, the DHCP client and the default IP address is disabled, which means that the obtained from DHCP or the default IP address 192.168.1.254 are more accessible.

    I would go to step 2, because it's the simplest solution to your problem and you would like a default static IP VLAN in any case, I guess.

    I hope this helps!

    Best regards

    Nico glacier

    Senior Network Engineer - CCNA

  • R8500: QOS is terrible on this router for $400

    So before you get this router I was using a $20 off of eBay refurbished Linksys router E6500 running DD WRT (Yes, you can run it on this router if you know where to find the firmware for this). In any case, the flow was not the greatest, but I never had problems.

    I have a ReadyNAS RN516 to my office and the backup on my Mac using the time machine office nas. I also have the Charter which gives single 4mbps upload (it's slow, but once he finished the initial and subsequent backup backups are fine). In real life, it's more like 4.75mbps. I have QOS value 3.75 to ensure that my modem is not bufferbloat and kill my connection.

    My problem is however that often my devices slow to a crawl (if more than 5 Ghz wireless or wired) whenever I am downloading. On my other router I just put 4 Mbps as the download limit and all devices than 4mbps equally, and I never had no problem with slowdowns or high pings and lag. No matter what I put the download speed at... He accuses just out for no apparent reason on this router.

    If someone can tell me why free DD WRT software works better than the software on a router for $400? Just curious?

    The new firmware seems to have helped. I changed a few things as well, and it seems to work very well.

    Regarding the comment of routers figure 3 and 4 routers in figure, there must be an improvement on the 2 figure routers and routers multi-3, otherwise what's the point?

    I'm trying the test of the future a little, that's why I chose this router. It doesn't matter if I take it right back and stick with my $ 20 DDWRT router. I do not have the latest and greatest tech (2012 macbook air and several iPhone 6 more ' and a room above the router and I can not even through any speedtests 60mbps (run through the gigabit mac that is wired and I move 65mbps each time.)

    I don't have a fast enough home nas box, but I'd be curious to see wireless local area network speeds. I wonder if I can break even 100 Mbps with this thing...

  • Can what comparison be made between time capsule and Smart RG s505 wireless modem router for wifi

    Can what comparison be made between time capsule and Smart RG s505 wireless modem router for wifi

    Superior...

    After all, the chip is mainly a modem.

    Wireless is there but not designed as the primary connection.

    Wireless 802.11n 300Mbps AP with 2 x 2 MIMO Wireless bridge, WDS multiple SSID, including isolated invited SSID WiFi QoS (WMM) and PowerSave wireless security: • Wi - Fi Protected Access (WPA, WPA2) • AES, TKIP, WEP encryptio

    It is the Wireless N standard.

    The TC is dual-band simultaneous AC1750... even if in fact apple never leaves anything use 300mbit on the 2.4 GHz is more like AC1450... It is also 3 streams on both bands not 2 x 2.

    The fact that aid.

    The only thing to note is that a router from Apple can join never a router wireless not apple... so, there must always be plugged in by ethernet.

  • I have a MN700 router for my wireless. How to reset the password?

    I have a MN700 router for my wireless. How to reset the password?

    I contacted Microsoft via the phone, but because they no longer carry this point they couldn't help me.

    Hello

    1. what operating system is installed on your computer?
    2 did you change your computer, after which the issue started?

    Here is the manual for the device...

    http://download.Microsoft.com/download/b/6/9/b69c956c-85d9-4641-aa6f-1548391e0967/mn700_base_station_configuration_guide.PDF

    Reset the router and set it up as if it was the first time. Then, you can simply choose a new password and security settings.

  • Need to modernize the modem; How do I 'plan' relocation WRT54G Router for wired / wireless

    I went late to upgrade my modem, and from what I've read in the comments, do a modem/router combo doesn't seem to be the best thing to do in what concerns the issues of reliability and range.  So, I want to upgrade my modem & then use the same router/access point that I currently have.  However, I've read other users with problems by accessing the control panel after you connect to a new modem... so want to know the information that I need to have before starting this project.

    Is this to say that I'm going to basically start early and set up my home network all over again?

    I'm pretty tech-savy... but I do not enough to really launch the project & see where it takes me... I don't have the TIME!  Laughing out loud!

    Thanks for any help/advice anyone can offer!

    Jane

    Really, it depends on the type of settings that your ISP would put on the new modem. If the configuration of the new modem would be the same with the old, so there is no need for you to make any changes on the router. Simply connect the new modem, perform a powercycle by unplugging the power cord from the modem and router and it should work. However, if it is not, what you can do is to reset the router and reconfigure. The following links help you reconfigure the router after a reset.

    Setting up a Linksys router with cable Internet service

    Setting up a Linksys router for DSL Internet connection

    Setting up a router with a static IP address account

  • Where to find the ability auto-raccordement on a router for PPPoE linsys for ADSL connection on request?

    Where to find the ability auto-raccordement on a router for PPPoE linsys for ADSL connection on request?

    Hello

    Use Linksys router information questions.

    Look for the router of the link exact model number.

    http://homesupport.Cisco.com/en-us/support?ICID=global-header-support-link

    See you soon.

  • I'm unable to watch videos on a certain type of site. They all now say, 'file not found '. They worked until I added a router for my Kindle Fire.

    I used to be able to watch videos on a certain type of site now all say file not found windows vista. I recently added a router for a kindle fire

    original title: streaming videos

    Hello

    ·          Do you mean that you use Internet Explorer 6 in Windows Vista?

    Windows Vista Internet Explorer 7 default features.

    http://Windows.Microsoft.com/en-us/Windows-Vista/find-out-which-version-of-Internet-Explorer-youre-using

  • Unable to connect to Homegroup Windows 7 between the Modem to the PC and the Modem to the router for PC users.

    I want to talk about WIRED computers, do not speak of wireless.

    I have 3 PC:

    -2 are connected via Modem directly to the PC.

    -1 is connected through router, and the router is connected to the modem.

    The problem, this is it, it cannot detect the homegroup that I created on the computer that is directly connected by modem.

    The 2 PC via modem are perfectly detected and connected to the homegroup, so I want to know what I would do to another PC (which is connected to the router via modem) detects the homegroup, I had already created?

    Help, please.

    A Modem can have only two ports, connect to the internet (Wide Area Network) and the second to a SINGLE local device. In most cases the internet Service Pwill provide with only an IP address so itself cannot connect to more than one at a time. In current solutions, it is very rare for a Modem to use. If as you say, you have several devices connected to this unit then he himself is a router but possibly with the Modem built in if you have ADSL ISP.

    If your second unit is also a router then that explains why you cannot connect all devices in the same residential group.

    Router 1 has created a Local Area Network including both PC and the WAN port on the Router 2. Router 2 has created another independent local network with the 3rd PC. It is very likely that the two local networks will be IPv4 and traffic can be routed between them correctly in both directions according to the two local networks subnet ranges.

    Even if they are properly configured to allow traffic that HomeGroup requires IPv6 that some home routers support fully and every Member of the residential group must be on the same LAN anyway, he will not support a routed connection.

    Remove the 3rd PC of the 2nd router and plug it into the direct 1 router, remove the router 2nd the 1st in order to free the port. 3 all PCs are now on the same local network and communicate both IPv4 and IPv6, and homegroup should work.

    If you need additional ports provided by the 2nd router for other devices is not part of this problem then consider replacing it with a switch. If you use Router 2 for other devices Wi - Fi irrelevant then you need a wireless access Point.

  • I want to know what I need to look at when buying a router for 50 concurrent users, 1 server connection information

    Original title: router Question.

    Hi all

    not sure if this is the right place to post but I was looking for some information about routers. specifically, I want to know what I need to look at when buying a router for 50 concurrent users, 1 server connection information. specifications, etc.

    Thanks :)

    Some routers will define a limited number of simultaneous connections. Domestic routers rarely do because the assumption is that the environment will not include such a high number.

    Ideally in a commercial environment you would separate on the hardware connection since the hardware firewall. It depends on the type of connection (ADSL?).

Maybe you are looking for

  • Is it possible to display an image full screen?

    I found a few larger images (986 x 1024 and 2420 x 2514) I'd like to see on the entire screen. Is there a way to do this by enabling / disabling (then restore it later) of all toolbars - including the status bar and the task bar? Or is there an FF ex

  • Question about resetting password IPAD?

    I apparently got myself a bit of a circular problem that I would be happy to help with.  I have an old IPAD 2 (WIFI only) I have stopped using about 8 months when I upgraded to AIR 2.  I took out the old IPAD today want to wipe so guests could use it

  • channel search

    Hello I'm programming an application in LV7.0.  The app is an extension of a previous application, and I need to find where strings are used throughout the program.  How do you search for a string in a vi and all sub vi, for a given application? Than

  • HP officejet pro: get instant ink

    How can I make instant ink to the new printer and remove the old printer

  • Read visa does not read as specified in bytes read