IOtech personnaldaq 3005

Similar Questions

• Unable to install audio drivers for Satellite 3005-S303

  Unable to install audio drivers for Satellite 3005 - S303, Windows XP SP2 installation of the Realtek AC97 drivers automatically, but with the error (blue screen). I tried to install the drivers of Crystal or Cirrus but Windows always changed for Realtek.

  Hello

  I found information on the net that this device supports a Crystal CS4299-A Codec chip.
  In this case, it should be possible to use the Crystal audio driver.
  As far as I know that he is an American unit. I searched the site of driver Toshiba us and have found a Crystal audio driver but only for Windows 98SE/Me/2000.
  If you have found the right driver, so I recommend you to remove first the driver of his former (Device Manager), then install the new.

  Here you can compare as you installed the BIOS with BIOS which is available on the site we Tosh.
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/Su/su_sc_home.jsp

• Can't find updates for my Satellite 3005 - s303

  Hello.
  I can't find a site update for Toshiba satellite 3005-s303
  It is absent from the list. My model of another which is in the list may what is similar, or there is another variant to update all drivers and BIOS for my Toshiba model.
  Thank you

  Hello

  I don't know what site you were watching. Your machine is the United States, here is a link to the download page for your machine.

  http://www.CSD.Toshiba.com/cgi-bin/TAIS/Su/su_sc_modItemList.jsp?MOID=1073833653&CT=DL&BV_Ses sionID=@@@1673061772.1127125127@@@&BV_EngineID=c ccfaddfjlffgggcgfkceghdgngdgnj.0

  Nick

• 3005 pro MT coprocessor driver for Win7 - 64 bit

  Kinda says it all. I have a desktop HP Pro 3005 MT with an AMD X processor 2 245, that I've upgraded to Windows 7 ultimate (64 bit). Everything works well except that the co-processor driver is not installed, and I can't seem to find anywhere (nothing online, pilots,). Apparently, the motherboard has a Nvidia Chipset, and the coprocessor driver should install with that. However, the page Pro 3005 MT drivers don't offer not a Nvidia Chipset driver down load for Windows 7 or any other OS no more. Any suggestions would be greatly appreciated.

  Added info! The motherboard uses NVIDIA GeForce 9100 chipset

  Thank you - RagnCagn

  PROBLEM SOLVED!

  Well, for what it's worth, I have finally found the right driver and solved this problem. Apparently, this link goes to a page of drivers HP for the MT 3005 Pro, but this is not the site takes you to when you type the number systen.  Anyway, the question of coprocessor is resolved. Here is a link to the page:

  http://www.driverscape.com/manufacturers/HP/laptops-desktops/HP-Pro-3005-microtower-PC/10307

  What you need to do is select the 'Coprocessor' driver in the list of drivers, click it, and then on the next screen scroll version: 5.1.26000208 (327.42 K) and downloaded to your desktop. Once downloaded, unzip it to a known location (I extracted on my desk). Now, on your desktop, go to the cutton to start, right click and go to "Device Manager" option in the upper left corner. Open it and click twice on the icon "coprocessor warning." Select the option "update driver" and guide them to the folder that you extracted the driver. Select the driver and leaves the system to update. Problem solved. Hope this helps someone.

• HP Pavilion dm4-3005 serious bug BIOS/drivers - ACPI.sys blocks constantly DPC to 3 milliseconds

  Some of our users reported problems with the HP Pavilion dm4, Intel i5, portable audio beats, so we bought such a system for the test, a HP Pavilion dm4-3005. The OS is Windows 7 Home Premium 64-bit.

  The questions were dropouts sound while using the software and USB audio interfaces that we do.

  Now, we have confirmed the questions and analyzed the cause behind it.

  The computer suffers from a DPC latency bottleneck, that fires continually in the OS ACPI.sys driver.

  ("CPD" is a regular work of pilots (Deferred Procedure Call).)

  Each DPC planned by each driver must always end quickly (less than 100 microseconds), or it causes a bug which acts as a bottleneck. When a long DPC runs in a driver, all other drivers are often necessarily suspended, for example, on a machine that behaves in the way reported, Windows can not reliable service all the drivers that need to run more often than once every 3-4 milliseconds.

  Low latency is necessary for all reception record, DAW, music app, software synth, as well as pro audio interface hardware drivers.

  Because of the congestion, they all suffer from heavy sound artifacts more use cases / underallocations for the pilot of the audio interface. This includes our products but also in any other software low latency and USB audio interfaces.

  HP Pavilion dm4-3005 has in this way from the factory, and no matter what drivers are disabled or set to date.
  I ran all the critical updates for installation of Windows 7 Home Premium 64-bit.

  I downloaded and installed all the updates driver from HP support.

  Finally, I also downloaded the BIOS update that available to HP support.

  I also followed several guides to address these issues, including advice prevailing to disable the driver "ACPI Compliant control method battery" in Device Manager (Edit: filled in the name of the pilot.)

  Does not the initial problem.

  I guess it's a bug in the BIOS - which has yet to be resolved by HP or their partner of BIOS for this product.

  I have the computer factory reset and ready for testing your solution, when it will be available.

  As it is now, we must warn our users of these systems because of their unusable latency.

  HP is aware of this problem?

  Thank you very much

  John Engstrom

  Developer

  Propellerhead Software

  Hello world

  I have good news for you, dm4-30xx users!

  The new BIOS is completed and will be published shortly by HP (need to package configuration file and write the documentation now...). The update of the BIOS version will be the F.0B.

  However, I have access to the "raw" version of this new BIOS. I can send it to you if you ask me, but in this case, you will assume any bad use of this file. In this case, please send me your mail by MP.

  The official release will not take much time, so I think it's best that you wait.

  Best regards!

• Voltage Excitation for IEPE/ICP and IOTech 650U

  Hi all

  I am using IOTech DAQ 650U (OR product no. 781277-01) with ICP/IEPE accelerometer. It works very well with accelerometers of general purpose PCB/IMI (IMI 607 A 11 model example). We want to use seismic accelerometers and wonder if IOtech 650U can collect data from seismic sensors (example - IMI 626 A 04 model). Most of the electrical specifications of the two sensors are similar (2-20 my constant current), except that the voltage is more versatile (18-28 VDC) for seismic sensor (24-28 VDC). -What it means and means of IOTech 650U does not work with seismic sensor? I don't think, but I'm not sure. I tried to read about this subject and found NO article on voltage is lower than the voltage of compliance (http://digital.ni.com/public.nsf/allkb/3CEFD95B14604C7386257598006C6233).
  However, I couldn't find the conformity of IOTech 650U voltage specifications. Any help in this regard is highly appreciated. I want to know if we can use the accelerometer seismic (IMI 626 A 04) with IOTech 650U or not? Thank you.

  Usually you want to measure low or very low frequencies with seismic sensors.

  So check to see if the high passes of frequency of your data acquisition fits your needs.

  A lot more low power low voltage will only limit max amplitude can be measured...

• How to set the differential input for personal iotech Daq/3000 mode

  Hi all

  I currently use personal iotech daq/3000 for the acquisition of data from the accelerometer.

  I got readings of the analog input, while there seems to be no configuration for the differential mode.

  What I have is:

  selection of material - personaldaq / 3000:direct

  Double click on, then:

  Channel installation, there should be a selection of differential mode, I guess. But this is not.

  Thank you very much

  Alan

  Have you reviewed the C:\Program Files\DASYLab 10.0\manuals\IOtech_DAQ_notes. PDF? Or the help of equipment?

  The section of material assistance, using the analog inputs with DASYLab, includes pictures to show how to do this.

  Open hardware driver.

  Click the line Analog Input Channels, and then right-click to open the properties. This will display a dialog box that allows you to set the properties.

• IOTech use for tiara in Windows 7

  Hi all...

  I use IOTech 650U, eZ-analyst for the acquisition of vibration data and DIAdem 2012 for post-processing and analysis. I used IOTech use to import the .dsc files in DIAdem. This is all on Windows XP. We will run Windows 7 64-bit. My question is will work fine, that is to say -

  1 eZ-analyst (I think is a 32-bit software)

  2 tiara (I think is a 32-bit software)

  3 use

  I talked to rep OR and knew that eZ-analyst and DIAdem 2012 should work fine without any performance problems, especially when acquiring data (mult-channel and high sampling rate). My question is about the use. Which works perfectly under Windows7 64-bit? If someone checked that? My concern is also because these products are not much upgraded. Please answer if you know about it. Thank you.

  Hi dream,

  I have no experience with eZ-analyst, so I won't be able to make statements concerning this product.

  In what concerns the tiara and any DataPlugins you may have, they will work just fine with Windows 7 32-bit or 64-bit versions of Windows 7 (such as 32-bit applications).

  I'm not sure what you are referring to this statement: "my concern is also because these products are not much upgraded."

  Here's the tiara lifecycle policy document, it should address questions of OS support: Policy of Life Cycle of DIAdem

  DataPlugins always work with the current version of the tiara.

  Best regards

  Otmar

• Router E1200 works not - error 3005 (and network does not connect by hand)

  I am trying to put in place a new monitor of N300 E1200 and am not having any luck. Using the Cisco Connect ends with an error in step 'Validate the connection' each time, telling me:

  Error: 3005

  An HNAP call to the device failed because the HTTP connection was broken.

  (If it is relevant, the serioal number, type of connection and IP (WAN) all happen as "unknown" in the details of the error).

  I am able to set up the router manually via the access by web browser. I can name the wifi network, set up security, and even see and authenticate to the network of my devices, however, no connection is available when it is connected. (The internet connection is good - when I move the incoming cable between the router and computer, I instantly have access - so perfect this post)

  I also tried all the basic steps of reset and restart all involved several times, but I always end with the same result - 3005 error in the application configuration, then on a manually configured wifi network that seems to be working and can authenticate devices, but does not include any internet connection.

  I am at a loss at this point - here someone has any advice? Thank you very much for your time and input.

  -e.

  Then you must configure PPPoe in the router, unless your ADSL modem is already acting as a router and not the PPPoe.

• VPN tunnel between the concentrator 3005 and router Cisco 827

  I am trying to establish a VPN tunnel between the Central Office with VPN 3005 and controller branch Cisco 827 router.

  There is a router of perimeter with access set up in front of the 3005 list.

  I quote the ACLs on the Central perimeter router instructionsuivante to allow traffic to permit ip 3005 - acl 101 all 193.188.X.X (address of the hub)

  I get the following message appears when I try to ping a local host in the Central site.

  Can Anyoune give me the correct steps to 827 and 3005.

  Thank you

  CCNP Ansar.

  ------------------------------------------------------------------------------------------------------

  Debug crypto ISAKMP

  encryption of debugging engine

  Debug crypto his

  debug output

  ------------------

  1d20h: IPSEC (sa_request):,.

  (Eng. msg key.) Local OUTGOING = 172.22.113.41, distance = 193.188.108.165.

  local_proxy = 202.71.244.160/255.255.255.240/0/0 (type = 4),

  remote_proxy = 128.128.1.78/255.255.255.255/0/0 (type = 1),

  Protocol = ESP, transform = esp - esp-md5-hmac.

  lifedur = 3600 s and KB 4608000,

  SPI = 0x83B8AC1B (2209917979), id_conn = 0, keysize = 0, flags = 0x400D

  1d20h: ISAKMP: ke received message (1/1)

  1d20h: ISAKMP: 500 local port, remote port 500

  1d20h: ISAKMP (0:1): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM

  Former State = new State IKE_READY = IKE_I_MM1

  1d20h: ISAKMP (0:1): early changes of Main Mode

  1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE...

  1d20h: ISAKMP (0:1): will increment the error counter on his: retransmit the phase 1

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE

  1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE...

  1d20h: ISAKMP (0:1): will increment the error counter on his: retransmit the phase 1

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE

  1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE

  1d20h: IPSEC (key_engine): request timer shot: count = 1,.

  You must also allow the esp Protocol in your ACL.

  access-list 101 permit esp any host x.x.x.x (address of the hub)

  Hope this helps,

  -Nairi

• Issue of IAS with the Conc 3005 configuration

  I have install IAS on 2003 Server to authenticate users. I think I installed everything correctly except for the type of authentication used by the 3005 and I'm stuck. It seems that the 3005 uses PAP to authenticate with IAS. I get the following error when you use the function Test (of the RADIUS authentication server) and when you actually try to connect to the 3005 with the IPSEC client.

  Tim user refused access.

  .

  .

  .

  NAS-Port-Type = virtual

  NAS-Port = 1056

  Proxy-policy-Name = use Windows authentication for all users

  Authentication provider = Windows

  Authentication server =

  Policy-Name = authenticate all VPN connections

  Authentication type PAP =

  EAP-Type =

  Code motif = 66

  Us reson = user attempted an authentication method that is not enabled on the matching remote access policy.

  To test I go ahead and enable PAP authentication on the IAS remote access policy and the RRAS remote access policy. With this I can connect without problems and see an IAS attesting to the authentication event. If I disable the PAP on IAS or RRAS political I get the same error as above. So, it looks like the 3005 uses PAP to authenticate to the IAS server.

  For the life of me I can't figure out how to use MSCHAP2. When I look at the properties of the database group AND the Test group, the only place to configure the authentication type is PPTP/L2TP tab and is not for IPSEC. However, the only verified method that there is MSCHAP-2.

  I'm sure that everything is set up correctly, because if I use a wrong password or try to connect when switched is disabled in AD I get a legitimate protest telling me I used a wrong password or RA is disabled on the account. I know that IAS correctly makes an AD request.

  Can someone tell me what I am doing wrong? How can I get the 3005 use MSCHAP-2 when you query the IAS server?

  Don't worry about this too. Concentrator use probably 02 attribute RADIUS User-Password instead of Chap 03-word of past, but the password itself is not sent in the clear. It is chopped by RADIUS shared secret. If you need MS-CHAP exchange between the RADIUS server and the hub to try to set up authentication = RADIUS with expiry on the tab screen IPSec change group. I didn't test it, but sure enough this expiration feature requires MS-CHAP exchage unfold. Please, drop a message if you get a success.

  Kind regards

  Oleg Tipisov,

  REDCENTER

• 3005 integrated VPN with ACS and server RSA auth

  Hi guys, I have a VPN 3005, using the version 4.7.2.B version, and I have the following problem.

  When a remote user using the Cisco VPN client tries to connect to the VPN 3005, it must try twice to authenticate.

  The first test, the user is authenticated, but the connection is immediately undermined by the peer.

  After the second attempt, the user is authenticated ok.

  Pablo,

  When you use RADIUS authentication on the hub, the ACS server will automatically send all the attributes of the user towards the concentrator for the user who is connecting. There is no need to have the authorization to be configured on the RADIUS server.

  According to the newspapers, it looks like the IP pool is the problem.

  [GroupP] user group [tuser] obtained IP addr (192.168.32.128) before launching the Cfg Mode (active XAuth)

  Subnet mask of the user [tuser] sending [GroupP] (255.255.255.224) group to the remote client

  User group [GroupP] [tuser] attempt to assign network or broadcast IP address, remove (192.168.32.128) of the

  After that, I see the customer negotiation again and the client is connected.

  Thus, the IP address is removed from the pool. Please make sure that you set up a pool that does not have a broadcast IP address.

  Thank you

  Gilbert

  Write it down, if this post can help.

• VPN 3005 concentrator Web Administration fails

  I have a vpn concentrator 3005 I can't connect to the web administration page. When I have the access concentrator, I get an HTTP 403 forbidden error. IE, the details of the error is "this error (HTTP 403 Forbidden) means that Internet Explorer was able to connect on the site, but it doesn't have permission to view the Web page." I tried several machines and Firefox as well, but all give the same error. I have no problem with the administration via telnet, but wishes to get the web interface works again. I even tried updating the hub to 4.7.2.P (from 4.7.2.O), but it does not solve the problem either. I also noticed an error in the event log which shows demand and an error HTTP 404 not found (/). Any ideas?

  On your interfaces, for example, "Configuration | Interfaces | Ethernet 1 ", on the WebVPN tab you have the check box for"allow management HTTPS sessions "?

• Recovery password: VPN 3005 concentrator

  How 3005 Concentrator VPN admin password.

  Here is the procedure

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_password_recovery09186a008009434f.shtml

• reset the admin pass cvpn 3005

  Hello

  I have a cvpn 3005 but I need to reset the admin password, without configuration has lost, someone at - it documentation on this subject?

  Here you go, it's the only doc for password recovery.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_password_recovery09186a008009434f.shtml