Ipad Cisco ipsec VPN connects but not access to the local network
Hi guys,.
I am trying to connect our ipads to vpn to access network resources. IPSec cisco ipad connects but not lan access and cannot ping anything not even not the interfaces of the router.
If I configure the vpn from cisco on a laptop, it works perfectly, I can ping all and can access resources on the local network if my guess is that the traffic is not going in the tunnel vpn between ipad and desktop.
Cisco 877.
My config is attached.
Any ideas?
Thank you
Build-in iPad-client is not useful to your configuration.
You have three options:
(1) remove the ACL of your vpn group. Without split tunneling client will work.
2) migrate legacy config crypto-map style. Here, you can use split tunneling
3) migrate AnyConnect.
The root of the problem is that the iPad Gets the split tunneling-information. But instead of control with routing traffic should pass through the window / the tunnel and which traffic is allowed without the VPN of the iPad tries to build a set of SAs for each line in your split-tunnel-ACL. But with the model-virtual, SA only is allowed.
Tags: Cisco Security
Similar Questions
-
ASA 5505 IPSEC VPN connected but cannot access the local network
ASA: 8.2.5
ASDM: 6.4.5
LAN: 10.1.0.0/22
Pool VPN: 172.16.10.0/24
Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.
I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.
Here is my setup, wrong set up anything?
ASA Version 8.2 (5)
!
hostname asatest
domain XXX.com
activate 8Fw1QFqthX2n4uD3 encrypted password
g9NiG6oUPjkYrHNt encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 10.1.1.253 255.255.252.0
!
interface Vlan2
nameif outside
security-level 0
address IP XXX.XXX.XXX.XXX 255.255.255.240
!
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS server-group DefaultDNS
domain vff.com
vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0
access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
logging trap warnings
asdm of logging of information
logging - the id of the device hostname
host of logging inside the 10.1.1.230
Within 1500 MTU
Outside 1500 MTU
IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol nt AD
AAA-server host 10.1.1.108 AD (inside)
NT-auth-domain controller 10.1.1.108
Enable http server
http 10.1.0.0 255.255.252.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 10.1.0.0 255.255.252.0 inside
SSH timeout 20
Console timeout 0
dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal group vpntest strategy
Group vpntest policy attributes
value of 10.1.1.108 WINS server
Server DNS 10.1.1.108 value
Protocol-tunnel-VPN IPSec l2tp ipsec
disable the password-storage
disable the IP-comp
Re-xauth disable
disable the PFS
IPSec-udp disable
IPSec-udp-port 10000
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpntest_splitTunnelAcl
value by default-domain XXX.com
disable the split-tunnel-all dns
Dungeon-client-config backup servers
the address value vpnpool pools
admin WeiepwREwT66BhE9 encrypted privilege 15 password username
username user5 encrypted password privilege 5 yIWniWfceAUz1sUb
the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username
tunnel-group vpntest type remote access
tunnel-group vpntest General attributes
address vpnpool pool
authentication-server-group AD
authentication-server-group (inside) AD
Group Policy - by default-vpntest
band-Kingdom
vpntest group tunnel ipsec-attributes
pre-shared-key BEKey123456
NOCHECK Peer-id-validate
!
!
privilege level 3 mode exec cmd command perfmon
privilege level 3 mode exec cmd ping command
mode privileged exec command cmd level 3
logging of the privilege level 3 mode exec cmd commands
privilege level 3 exec command failover mode cmd
privilege level 3 mode exec command packet cmd - draw
privilege show import at the level 5 exec mode command
privilege level 5 see fashion exec running-config command
order of privilege show level 3 exec mode reload
privilege level 3 exec mode control fashion show
privilege see the level 3 exec firewall command mode
privilege see the level 3 exec mode command ASP.
processor mode privileged exec command to see the level 3
privilege command shell see the level 3 exec mode
privilege show level 3 exec command clock mode
privilege exec mode level 3 dns-hosts command show
privilege see the level 3 exec command access-list mode
logging of orders privilege see the level 3 exec mode
privilege, level 3 see the exec command mode vlan
privilege show level 3 exec command ip mode
privilege, level 3 see fashion exec command ipv6
privilege, level 3 see the exec command failover mode
privilege, level 3 see fashion exec command asdm
exec mode privilege see the level 3 command arp
command routing privilege see the level 3 exec mode
privilege, level 3 see fashion exec command ospf
privilege, level 3 see the exec command in aaa-server mode
AAA mode privileged exec command to see the level 3
privilege, level 3 see fashion exec command eigrp
privilege see the level 3 exec mode command crypto
privilege, level 3 see fashion exec command vpn-sessiondb
privilege level 3 exec mode command ssh show
privilege, level 3 see fashion exec command dhcpd
privilege, level 3 see the vpnclient command exec mode
privilege, level 3 see fashion exec command vpn
privilege level see the 3 blocks from exec mode command
privilege, level 3 see fashion exec command wccp
privilege see the level 3 exec command mode dynamic filters
privilege, level 3 see the exec command in webvpn mode
privilege control module see the level 3 exec mode
privilege, level 3 see fashion exec command uauth
privilege see the level 3 exec command compression mode
level 3 for the show privilege mode configure the command interface
level 3 for the show privilege mode set clock command
level 3 for the show privilege mode configure the access-list command
level 3 for the show privilege mode set up the registration of the order
level 3 for the show privilege mode configure ip command
level 3 for the show privilege mode configure command failover
level 5 mode see the privilege set up command asdm
level 3 for the show privilege mode configure arp command
level 3 for the show privilege mode configure the command routing
level 3 for the show privilege mode configure aaa-order server
level mode 3 privilege see the command configure aaa
level 3 for the show privilege mode configure command crypto
level 3 for the show privilege mode configure ssh command
level 3 for the show privilege mode configure command dhcpd
level 5 mode see the privilege set privilege to command
privilege level clear 3 mode exec command dns host
logging of the privilege clear level 3 exec mode commands
clear level 3 arp command mode privileged exec
AAA-server of privilege clear level 3 exec mode command
privilege clear level 3 exec mode command crypto
privilege clear level 3 exec command mode dynamic filters
level 3 for the privilege cmd mode configure command failover
clear level 3 privilege mode set the logging of command
privilege mode clear level 3 Configure arp command
clear level 3 privilege mode configure command crypto
clear level 3 privilege mode configure aaa-order server
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4
: end
Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.
The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.
On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.
-
Cisco ipsec Vpn connects but cannot communicate with lan
I have a version of cisco 1921 15.2 (4) M3 I install vpn ipsec and may have customers to connect but cannot ping anything inside. A glimpse of what could be wrong with my config would be greatly appreciated. I posted the configuration as well as running a few outings of ipsec. I also tried with multiple operating systems using cisco vpn client and shrewsoft. I am able to connect to the other VPN ipsec running 1921 both of these computers by using a client.
Thanks for any assistance
SH run
!
AAA new-model
!
!
AAA authentication login radius_auth local radius group
connection of AAA VPN_AUTHEN group local RADIUS authentication
AAA authorization network_vpn_author LAN
!
!
!
!
!
AAA - the id of the joint session
clock timezone PST - 8 0
clock to summer time recurring PST
!
no ip source route
decline of the IP options
IP cef
!
!
!
!
!
!
no ip bootp Server
no ip domain search
domain IP XXX.local
inspect the high IP 3000 max-incomplete
inspect the low IP 2800 max-incomplete
IP inspect a low minute 2800
IP inspect a high minute 3000
inspect the IP icmp SDM_LOW name
inspect the IP name SDM_LOW esmtp
inspect the tcp IP SDM_LOW name
inspect the IP udp SDM_LOW name
IP inspect name SDM_LOW ssh
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
Crypto pki trustpoint TP-self-signed-2909270577
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 2909270577
revocation checking no
rsakeypair TP-self-signed-2909270577
!
!
TP-self-signed-2909270577 crypto pki certificate chain
certificate self-signed 01
license udi pid CISCO1921/K9 sn FTX1715818R
!
!
Archives
The config log
Enable logging
size of logging 1000
notify the contenttype in clear syslog
the ADMIN_HOSTS object-group network
71.X.X.X 71.X.X.X range
!
name of user name1 secret privilege 15 4 XXXXXXX!
redundancy
!
!
!
!
!
property intellectual ssh time 60
property intellectual ssh authentication-2 retries
property intellectual ssh event logging
property intellectual ssh version 2
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
ISAKMP crypto client configuration group roaming_vpn
key XXXXX
DNS 192.168.10.10 10.1.1.1
XXX.local field
pool VPN_POOL_1
ACL client_vpn_traffic
netmask 255.255.255.0
!
!
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
tunnel mode
!
!
!
crypto dynamic-map VPN_DYNMAP_1 1
Set the security association idle time 1800
game of transformation-ESP-3DES-SHA
market arriere-route
!
!
list of authentication of card crypto SDM_CMAP_1 client VPN_AUTHEN
map SDM_CMAP_1 isakmp authorization list network_vpn_author crypto
client configuration address map SDM_CMAP_1 crypto answer
map SDM_CMAP_1 65535-isakmp dynamic VPN_DYNMAP_1 ipsec crypto
!
!
!
!
!
the Embedded-Service-Engine0/0 interface
no ip address
Shutdown
!
interface GigabitEthernet0/0
IP 76.W.E.R 255.255.255.248
IP access-group ATT_Outside_In in
no ip redirection
no ip unreachable
no ip proxy-arp
NAT outside IP
inspect the SDM_LOW over IP
IP virtual-reassembly in
load-interval 30
automatic duplex
automatic speed
No cdp enable
No mop enabled
map SDM_CMAP_1 crypto
!
interface GigabitEthernet0/1
no ip address
load-interval 30
automatic duplex
automatic speed
!
interface GigabitEthernet0/1.10
encapsulation dot1Q 1 native
IP 192.168.10.1 255.255.255.0
no ip redirection
no ip unreachable
no ip proxy-arp
property intellectual accounting-access violations
IP nat inside
IP virtual-reassembly in
!
interface GigabitEthernet0/1.100
encapsulation dot1Q 100
10.1.1.254 IP address 255.255.255.0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
IP virtual-reassembly in
!
interface GigabitEthernet0/1,200
encapsulation dot1Q 200
IP 10.1.2.254 255.255.255.0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
IP virtual-reassembly in
IP tcp adjust-mss 1452
!
local IP VPN_POOL_1 192.168.168.193 pool 192.168.168.254
IP forward-Protocol ND
!
IP http server
IP http authentication aaa-authentication of connection ADMIN_AUTHEN
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
IP nat inside source map route ATT_NAT_LIST interface GigabitEthernet0/0 overload
IP nat inside source static tcp 192.168.10.10 25 expandable 25 76.W.E.R
IP nat inside source static tcp 192.168.10.10 80 76.W.E.R 80 extensible
IP nat inside source static tcp 192.168.10.10 76.W.E.R expandable 443 443
IP nat inside source static tcp 192.168.10.10 76.W.E.R expandable 987 987
IP route 0.0.0.0 0.0.0.0 76.W.E.F
!
ATT_Outside_In extended IP access list
permit tcp object-group ADMIN_HOSTS any eq 22
allow any host 76.W.E.R eq www tcp
allow any host 76.W.E.R eq 443 tcp
allow 987 tcp any host 76.W.E.R eq
allow any host 76.W.E.R eq tcp smtp
permit any any icmp echo response
allow icmp a whole
allow udp any any eq isakmp
allow an esp
allow a whole ahp
permit any any eq non500-isakmp udp
deny ip 10.0.0.0 0.255.255.255 everything
deny ip 172.16.0.0 0.15.255.255 all
deny ip 192.168.0.0 0.0.255.255 everything
deny ip 127.0.0.0 0.255.255.255 everything
refuse the ip 255.255.255.255 host everything
refuse the host ip 0.0.0.0 everything
NAT_LIST extended IP access list
IP 10.1.0.0 allow 0.0.255.255 everything
permit ip 192.168.10.0 0.0.0.255 any
deny ip 192.168.10.0 0.0.0.255 192.168.168.192 0.0.0.63
refuse the 10.1.1.0 ip 0.0.0.255 192.168.168.192 0.0.0.63
deny ip 10.1.2.0 0.0.0.255 192.168.168.192 0.0.0.63
client_vpn_traffic extended IP access list
permit ip 192.168.10.0 0.0.0.255 192.168.168.192 0.0.0.63
ip licensing 10.1.1.0 0.0.0.255 192.168.168.192 0.0.0.63
IP 10.1.2.0 allow 0.0.0.255 10.1.1.0 0.0.0.255
!
radius of the IP source-interface GigabitEthernet0/1.10
Logging trap errors
logging source hostname id
logging source-interface GigabitEthernet0/1.10
!
ATT_NAT_LIST allowed 20 route map
corresponds to the IP NAT_LIST
is the interface GigabitEthernet0/0
!
!
SNMP-server community [email protected] / * /! s RO
Server enable SNMP traps snmp authentication linkdown, linkup warmstart cold start
Server enable SNMP traps vrrp
Server SNMP enable transceiver traps all the
Server enable SNMP traps ds1
Enable SNMP-Server intercepts the message-send-call failed remote server failure
Enable SNMP-Server intercepts ATS
Server enable SNMP traps eigrp
Server enable SNMP traps ospf-change of State
Enable SNMP-Server intercepts ospf errors
SNMP Server enable ospf retransmit traps
Server enable SNMP traps ospf lsa
Server enable SNMP traps ospf nssa-trans-changes state cisco-change specific
SNMP server activate interface specific cisco-ospf traps shamlink state change
SNMP Server enable neighbor traps cisco-specific ospf to the State shamlink change
Enable SNMP-Server intercepts specific to cisco ospf errors
SNMP server activate specific cisco ospf retransmit traps
Server enable SNMP traps ospf cisco specific lsa
SNMP server activate license traps
Server enable SNMP traps envmon
traps to enable SNMP-Server ethernet cfm cc mep-top low-mep Dispatcher loop config
Enable SNMP-Server intercepts ethernet cfm overlap missing mep mep-unknown service-up
Server enable SNMP traps auth framework sec-violation
Server enable SNMP traps c3g
entity-sensor threshold traps SNMP-server enable
Server enable SNMP traps adslline
Server enable SNMP traps vdsl2line
Server enable SNMP traps icsudsu
Server enable SNMP traps ISDN call-information
Server enable SNMP traps ISDN layer2
Server enable SNMP traps ISDN chan-not-available
Server enable SNMP traps ISDN ietf
Server enable SNMP traps ds0-busyout
Server enable SNMP traps ds1-loopback
SNMP-Server enable traps energywise
Server enable SNMP traps vstack
SNMP traps enable mac-notification server
Server enable SNMP traps bgp cbgp2
Enable SNMP-Server intercepts isis
Server enable SNMP traps ospfv3-change of State
Enable SNMP-Server intercepts ospfv3 errors
Server enable SNMP traps aaa_server
Server enable SNMP traps atm subif
Server enable SNMP traps cef resources-failure-change of State peer peer-fib-state-change inconsistency
Server enable SNMP traps memory bufferpeak
Server enable SNMP traps cnpd
Server enable SNMP traps config-copy
config SNMP-server enable traps
Server enable SNMP traps config-ctid
entity of traps activate SNMP Server
Server enable SNMP traps fru-ctrl
SNMP traps-policy resources enable server
Server SNMP enable traps-Manager of event
Server enable SNMP traps frames multi-links bundle-incompatibility
SNMP traps-frame relay enable server
Server enable SNMP traps subif frame relay
Server enable SNMP traps hsrp
Server enable SNMP traps ipmulticast
Server enable SNMP traps msdp
Server enable SNMP traps mvpn
Server enable SNMP traps PNDH nhs
Server enable SNMP traps PNDH nhc
Server enable SNMP traps PNDH PSN
Server enable SNMP traps PNDH exceeded quota
Server enable SNMP traps pim neighbor-rp-mapping-change invalid-pim-message of change
Server enable SNMP traps pppoe
Enable SNMP-server holds the CPU threshold
SNMP Server enable rsvp traps
Server enable SNMP traps syslog
Server enable SNMP traps l2tun session
Server enable SNMP traps l2tun pseudowire status
Server enable SNMP traps vtp
Enable SNMP-Server intercepts waas
Server enable SNMP traps ipsla
Server enable SNMP traps bfd
Server enable SNMP traps gdoi gm-early-registration
Server enable SNMP traps gdoi full-save-gm
Server enable SNMP traps gdoi gm-re-register
Server enable SNMP traps gdoi gm - generate a new key-rcvd
Server enable SNMP traps gdoi gm - generate a new key-fail
Server enable SNMP traps gdoi ks - generate a new key-pushed
Enable SNMP traps gdoi gm-incomplete-cfg Server
Enable SNMP-Server intercepts gdoi ks-No.-rsa-keys
Server enable SNMP traps gdoi ks-new-registration
Server enable SNMP traps gdoi ks-reg-complete
Enable SNMP-Server Firewall state of traps
SNMP-Server enable traps ike policy add
Enable SNMP-Server intercepts removal of ike policy
Enable SNMP-Server intercepts start ike tunnel
Enable SNMP-Server intercepts stop ike tunnel
SNMP server activate ipsec cryptomap add traps
SNMP server activate ipsec cryptomap remove traps
SNMP server activate ipsec cryptomap attach traps
SNMP server activate ipsec cryptomap detach traps
Server SNMP traps enable ipsec tunnel beginning
SNMP-Server enable traps stop ipsec tunnel
Enable SNMP-server holds too many associations of ipsec security
Enable SNMP-Server intercepts alarm ethernet cfm
Enable SNMP-Server intercepts rf
Server enable SNMP traps vrfmib vrf - up low-vrf vnet-trunk-up low-trunk-vnet
Server RADIUS dead-criteria life 2
RADIUS-server host 192.168.10.10
Server RADIUS 2 timeout
Server RADIUS XXXXXXX key
!
!
!
control plan
!
!Line con 0
privilege level 15
connection of authentication radius_auth
line to 0
line 2
no activation-character
No exec
preferred no transport
transport of entry all
transport output pad rlogin lapb - your MOP v120 udptn ssh telnet
StopBits 1
line vty 0 4
privilege level 15
connection of authentication radius_auth
entry ssh transport
line vty 5 15
privilege level 15
connection of authentication radius_auth
entry ssh transport
!
Scheduler allocate 20000 1000
NTP-Calendar Update
Server NTP 192.168.10.10
NTP 64.250.229.100 Server
!
endRouter ipsec crypto #sh her
Interface: GigabitEthernet0/0
Tag crypto map: SDM_CMAP_1, local addr 76.W.E.Rprotégé of the vrf: (none)
local ident (addr, mask, prot, port): (0.0.0.0/0.0.0.0/0/0)
Remote ident (addr, mask, prot, port): (192.168.168.213/255.255.255.255/0/0)
current_peer 75.X.X.X port 2642
LICENCE, flags is {}
#pkts program: 1953, #pkts encrypt: 1953, #pkts digest: 1953
#pkts decaps: 1963, #pkts decrypt: 1963, #pkts check: 1963
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
Errors #send 0, #recv 0 errorslocal crypto endpt. : 76.W.E.R, remote Start crypto. : 75.X.X.X
Path mtu 1500, mtu 1500 ip, ip mtu IDB GigabitEthernet0/0
current outbound SPI: 0x5D423270 (1564619376)
PFS (Y/N): N, Diffie-Hellman group: noSAS of the esp on arrival:
SPI: 0x2A5177DD (709982173)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel UDP-program}
Conn ID: 2115, flow_id: VPN:115 on board, sibling_flags 80000040, crypto card: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4301748/2809)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVE (ACTIVE)the arrival ah sas:
SAS of the CFP on arrival:
outgoing esp sas:
SPI: 0x5D423270 (1564619376)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel UDP-program}
Conn ID: 2116, flow_id: VPN:116 on board, sibling_flags 80000040, crypto card: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4301637/2809)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVE (ACTIVE)outgoing ah sas:
outgoing CFP sas:
Routing crypto isakmp #sh its
IPv4 Crypto ISAKMP Security Association
DST CBC conn-State id
76.W.E.R 75.X.X.X QM_IDLE 1055 ACTIVEIPv6 Crypto ISAKMP Security Association
In your acl, nat, you will need to refuse your VPN traffic before you allow the subnet at all. Just put all the declarations of refusal before the declarations of licence.
Sent by Cisco Support technique iPhone App
-
My iPad mini links is no longer in my Bluetooth from Sony speakers since the last 'upgrade' to iOS. I rebooted the iPad. I unpaired and repair the speakers. Showes Bluetooth as connected but the train continues spinning saying: it is always looking for devices even though it says it has paired with speakers. Any suggestions? and Yes, the volume is rising.
Tap settings > general > reset > reset all settings and restart your iPad then re "pair" speakers.
-
Remote VPN with PIX without access to the local network
Hi @all,
I ve running into problems and I have not found any solution. Can someone check my config?
Facts:
PIX 501 6.3 (3)
4.04 VPN client
Wanted solution: access to HO via VPN
VPN tunnel will be established, I get an IP address, but I can´t the systems behind the pix and the pix of access itself.
To the VPN Client Staticts, I see outgoing packets, but no entrant (if I send a ping to peer behind the pix)
I hope someone can help me
Attached is my config:
PIX 501 and 506/506e pix are not supported in v7 due to the fact that the cpu is not able to deal with the extended features of v7.
PIX 520 is not supported I guess it's because of the fact that the model is discontinued.
-
Cisco vpn client to connect but can not access to the internal network
Hi all
I have a VPN configured on cisco 5540. My vpn was working fine, but suddenly there is a question that the cisco vpn client to connect but can not access to the internal network
Any help would be much appreciated.
Hi Samir,
I suggest that you go to the ASA and check the configuration to make sure that it complies with the requirements according to the reference below link:
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml
(The link above includes split tunneling, but this is just an option.
Please paste the output of "sh cry ipsec his" here so that we can check if phase 2 is properly trained. I would say as you go to IPSEC vpn client on your PC and check increment in packets sent and received in the window 'status '.
Let me know if this can help,
See you soon,.
Christian V
-
Client remote access VPN gets connected without access to the local network
: Saved
:
ASA 1.0000 Version 2
!
hostname COL-ASA-01
domain dr.test.net
turn on i/RAo1iZPOnp/BK7 encrypted password
i/RAo1iZPOnp/BK7 encrypted passwd
names of
!
interface GigabitEthernet0/0
nameif outside
security-level 0
IP 172.32.0.11 255.255.255.0
!
interface GigabitEthernet0/1
nameif inside
security-level 100
IP 192.9.200.126 255.255.255.0
!
interface GigabitEthernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
nameif failover
security-level 0
192.168.168.1 IP address 255.255.255.0 watch 192.168.168.2
!
interface Management0/0
nameif management
security-level 0
192.168.2.11 IP address 255.255.255.0
!
passive FTP mode
DNS server-group DefaultDNS
domain dr.test.net
network of the RAVPN object
192.168.0.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.200.0_24 object
192.168.200.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.9.200.0_24 object
192.9.200.0 subnet 255.255.255.0
the inside_network object-group network
object-network 192.9.200.0 255.255.255.0
external network object-group
host of the object-Network 172.32.0.25
Standard access list RAVPN_splitTunnelAcl allow 192.9.200.0 255.255.255.0
access-list extended test123 permit ip host 192.168.200.1 192.9.200.190
access-list extended test123 permit ip host 192.9.200.190 192.168.200.1
access-list extended test123 allowed ip object NETWORK_OBJ_192.168.200.0_24 192.9.200.0 255.255.255.0
192.9.200.0 IP Access-list extended test123 255.255.255.0 allow object NETWORK_OBJ_192.9.200.0_24
pager lines 24
management of MTU 1500
Outside 1500 MTU
Within 1500 MTU
failover of MTU 1500
local pool RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 66114.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) source Dynamics one interface
NAT (it is, inside) static static source NETWORK_OBJ_192.9.200.0_24 destination NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.9.200.0_24
Route outside 0.0.0.0 0.0.0.0 172.32.0.2 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 outdoors
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint ASDM_TrustPoint0
Terminal registration
name of the object CN = KWI-COL-ASA - 01.dr.test .net, C = US, O = KWI
Configure CRL
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet 192.9.200.0 255.255.255.0 inside
Telnet timeout 30
SSH 0.0.0.0 0.0.0.0 management
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 66.35.45.128 255.255.255.192 outside
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 30
SSH version 2
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
internal RAVPN group policy
RAVPN group policy attributes
value of server WINS 192.9.200.164
value of 66.35.46.84 DNS server 66.35.47.12
VPN-filter value test123
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value test123
Dr.kligerweiss.NET value by default-field
username test encrypted password xxxxxxx
username admin password encrypted aaaaaaaaaaaa privilege 15
vpntest Delahaye of encrypted password username
type tunnel-group RAVPN remote access
attributes global-tunnel-group RAVPN
address RAVPN pool
Group Policy - by default-RAVPN
IPSec-attributes tunnel-group RAVPN
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory 2
Subscribe to alert-group configuration periodic monthly 2
daily periodic subscribe to alert-group telemetry
aes encryption password
Cryptochecksum:b001e526a239af2c73fa56f3ca7667ea
: end
COL-ASA-01 #.
Here is a shot made inside interface which can help as well, I've tried pointing the front door inside the interface on the target device, but I think it was a switch without ip route available on this subject I think which is always send package back to Cisco within the interface
Test of Cape COLLAR-ASA-01 # sho | in 192.168.200
25: 23:45:55.570618 192.168.200.1 > 192.9.200.190: icmp: echo request
29: 23:45:56.582794 192.168.200.1.137 > 192.9.200.164.137: udp 68
38: 23:45:58.081050 192.168.200.1.137 > 192.9.200.164.137: udp 68
56: 23:45:59.583176 192.168.200.1.137 > 192.9.200.164.137: udp 68
69: 23:46:00.573517 192.168.200.1 > 192.9.200.190: icmp: echo request
98: 23:46:05.578110 192.168.200.1 > 192.9.200.190: icmp: echo request
99: 23:46:05.590057 192.168.200.1.137 > 192.9.200.164.137: udp 68
108: 23:46:07.092310 192.168.200.1.137 > 192.9.200.164.137: udp 68
115: 23:46:08.592468 192.168.200.1.137 > 192.9.200.164.137: udp 68
116: 23:46:10.580795 192.168.200.1 > 192.9.200.190: icmp: echo request
COL-ASA-01 #.
Any help or pointers greatly appreciated, I have do this config after a long interval on Cisco of the last time I was working it was all PIX so just need to expert eyes to let me know if I'm missing something.
And yes I don't have a domestic network host to test against, all I have is a switch that cannot route and bridge default ip helps too...
Hello
The first thing you should do to avoid problems is to change the pool VPN to something else than the current LAN they are not really directly connected in the same network segment.
You can try the following changes
attributes global-tunnel-group RAVPN
No address RAVPN pool
no mask RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 ip local pool
local pool RAVPN 192.168.201.1 - 192.168.201.254 255.255.255.0 IP mask
attributes global-tunnel-group RAVPN
address RAVPN pool
no nat (it is, inside) static source NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 static destination NETWORK_OBJ_192.9.200.0_24 NETWORK_OBJ_192.9.200.0_24
In the above you first delete the VPN "tunnel-group" Pool and then delete and re-create the VPN pool with another network and then insert the same "tunnel-group". NEX will remove the current configuration of the NAT.
the object of the LAN network
192.168.200.0 subnet 255.255.255.0
network of the VPN-POOL object
192.168.201.0 subnet 255.255.255.0
NAT (inside, outside) 1 static source LAN LAN to static destination VPN-VPN-POOL
NAT configurations above adds the correct NAT0 configuration for the VPN Pool has changed. It also inserts the NAT rule to the Summit before the dynamic PAT rule you currently have. He is also one of the problems with the configurations that it replaces your current NAT configurations.
You have your dynamic PAT rule at the top of your NAT rules currently that is not a good idea. If you want to change to something else will not replace other NAT configurations in the future, you can make the following change.
No source (indoor, outdoor) nat Dynamics one interface
NAT source auto after (indoor, outdoor) dynamic one interface
NOTICE! PAT dynamic configuration change above temporarily interrupt all connections for users on the local network as you reconfigure the dynamic State PAT. So if you make this change, make sure you that its ok to still cause little reduced in the current internal users connections
Hope this helps
Let me know if it works for you
-Jouni
-
Cisco ASA 5505 remote VPN access to the local network
I have installed two ASA 5505 VPN site to site that works perfectly. Now, I also need to have 1 customer site to remote access VPN with Cisco VPN dialer. I can get the VPN dialer to connect the VPN and get a VPN IP address, but I do not have access to the remote network. can someone take a look and see what I'm missing? I have attached the ASA running config.
Apologize for the misunderstanding.
To access the remote vpn client 10.10.100.x subnet, the vpn-filter ACL is the opposite.
Please please share the following ACL:
FROM: / * Style Definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-marge-haut : 0 cm ; mso-para-marge-droit : 0 cm ; mso-para-marge-bas : 10.0pt ; mso-para-marge-gauche : 0 cm ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}
outside_cryptomapVPN list of allowed ip extended access any 10.10.20.0 255.255.255.224
TO:
/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-marge-haut : 0 cm ; mso-para-marge-droit : 0 cm ; mso-para-marge-bas : 10.0pt ; mso-para-marge-gauche : 0 cm ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}
outside_cryptomapVPN to access extended list ip 10.10.20.0 allow 255.255.255.224 all
Hope that helps.
-
ASA5505 can transfer clients to remote VPN access to the local network
I have currently ASA 5505 and 2911-router and I am trying to configure the VPN topology.
Can ASA5505 you transmit to remote VPN access clients LAN operated by another router?
These two cases are possible? :
(1) ASA 5505 and 2911-router are separate WAN interfaces, each connected directly to the ISP. But so can I connect an other interfaces LAN of ASA 5505 in a switch managed by 2911 router customers to distance-SSL-VPN to inject into the local network managed by the router?
(2) ASA 5505 is behind router-2911. May 2911 router address public ip or public ip address VPN-access attempts have directly be sent to ASA 5505 when there is only a single public ip address address available?
Long put short, ASA 5505 can inject its clients to remote-access-VPN as one of the hosts on the local network managed by 2911-router?
Thank you.I could help you more if you can explain the purpose of this configuration and connectivity between the router and ASA.
You can activate the reverse route on the dynamic plane on the SAA. The ASA will install a static route to the customer on the routing table. You can use a routing protocol to redistribute static routes to your switch on the side of LAN of the SAA.
-
zero or change username & password for a connection to another computer on the local network?
When you open the network, and see you computers and or network for the Working Group action, well, I entered accidentally the wrong username / password for the computer, and I can't seem to change the username-password and or reset it.
On the local network, I have a linux machine using samba, all permissions are correct, since the box vista * can * connect just fine and have access to everything which, however, on the vista box, I checked still remember the name of user and password, and now I can't change it on another account, I need to take it.
I have searched for hours and I can't seem to find the answer.
I tried to disable the account on the linux side and this does not, however, so, he says: "access denied", with no way to enter a new username / password!
Anyone has an idea on how to solve this problem?
Finally found the answer.
In the cmd prompt, (Administrator rights), making control userpasswords2, and then tap the Advanced tab and finally, the button manage passwords.
-
AnyConnect VPN connected but not in LAN access
Hello
I just connfigured an ASA to remote VPN. I think everything works but I do not have access
for customers in the Local LAN behind the ASA.
PC <==internet==>outside of the SAA inside<=LAN=> PC
After AnyConnect has established the connection I can ping inside the Interface of the ASA
but I can't Ping the PC behind the inside Interface.
Here is the config of the ASA5505:
: Saved
:
ASA Version 8.2 (1)
!
asa5505 hostname
activate 8Ry2YjIyt7RRXU24 encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 192.168.178.254 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
Shutdown
!
interface Ethernet0/3
Shutdown
!
interface Ethernet0/4
Shutdown
!
interface Ethernet0/5
Shutdown
!
interface Ethernet0/6
Shutdown
!
interface Ethernet0/7
Shutdown
!
passive FTP mode
Inside_ICMP list extended access permit icmp any any echo response
Inside_ICMP list extended access permit icmp any any source-quench
Inside_ICMP list extended access allow all unreachable icmp
Inside_ICMP list extended access permit icmp any one time exceed
access-list outside_cryptomap_2 note ACL traffic von ASA5505 zur ASA5510
outside_cryptomap_2 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0
no_NAT to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0
no_NAT to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.178.0 255.255.255.0
tunnel of splitting allowed access list standard 192.168.1.0 255.255.255.0
pager lines 24
Within 1500 MTU
Outside 1500 MTU
mask 192.168.1.10 - 192.168.1.15 255.255.255.0 IP local pool SSLClientPool
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access no_NAT
NAT (inside) 1 192.168.1.0 255.255.255.0
Access-group Inside_ICMP in interface outside
Route outside 0.0.0.0 0.0.0.0 192.168.178.1 1
Route outside 192.168.10.0 255.255.255.0 192.168.178.230 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication http LOCAL console
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set-3DESSHA FRA esp-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto outside_map 2 match address outside_cryptomap_2
peer set card crypto outside_map 2 192.168.178.230
card crypto outside_map 2 game of transformation-FRA-3DESSHA
outside_map interface card crypto outside
Crypto ca trustpoint localtrust
registration auto
domain name full cisco - asa5505.fritz.box
name of the object CN = cisco - asa5505.fritz.box
sslvpnkeypair key pair
Configure CRL
Crypto ca certificate chain localtrust
certificate fa647850
3082020b a0030201 30820174 020204fa 0d06092a 64785030 864886f7 0d 010104
0500304 06035504 03131763 6973636f 617361 35353035 2e667269 2d 3120301e a
747a2e62 6f783126 30240609 2a 864886 f70d0109 02161763 6973636f 2d 617361
2e667269 35353035 747a2e62 6f78301e 170d 3132 31303132 31383434 31305a 17
323231 30313031 38343431 06035504 03131763 6973636f 3120301e 305a304a 0d=LAN=>==internet==>
617361 35353035 2e667269 747a2e62 6f783126 2a 864886 30240609 f70d0109 2D
6973636f 02161763 2d 617361 35353035 2e667269 747a2e62 6f783081 9f300d06
d6279e1c 8181009f 092a 8648 86f70d01 01010500 03818d 30818902 00 38454fc 9
705e1e58 762edc35 e64262fb ee55f47b 8d62dda2 102c8a22 c97e395f 2a9c0ebb
f2881528 beb6e9c3 89d91dda f7fe77a4 2a1fda55 f8d930b8 3310a05f 622dfc8f
d48ea749 7bbc4520 68 has 06392 d65d3b87 0270e41b 512a4e89 94e60167 e2fa854a
87ec04fa e95df04f 3ff3336e c7437e30 ffbd90b5 47308502 03010001 300 d 0609
2a 864886 04050003 81810065 cc9e6414 3c322d1d b191983c 97b474a8 f70d0101
2e5c7774 9d54d3ec fc4ee92d c72eef27 a79ce95a da83424f b05721c0 9119e7ea
c5431998 e6cd8272 de17b5ff 5b1839b5 795fb2a0 2d10b479 056478fa 041555dd
bfe3960a 4fe596ec de54d58b a5fa187e 5967789a a26872ef a33b73ec 7d7673b9
c8af6eb0 46425cd 2 765f667d 4022c 6
quit smoking
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
localtrust point of trust SSL outdoors
WebVPN
allow outside
SVC disk0:/anyconnect-win-2.3.0254-k9.pkg 1 image
SVC disk0:/anyconnect-wince-ARMv4I-2.3.0254-k9.pkg 2 image
enable SVC
tunnel-group-list activate
internal SSLClientPolicy group strategy
attributes of Group Policy SSLClientPolicy
VPN-tunnel-Protocol svc
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
the address value SSLClientPool pools
WebVPN
SVC Dungeon-Installer installed
time to generate a new key of SVC 30
SVC generate a new method ssl key
SVC request no svc default
username password asdm privilege Yvx83jxa2WCRAZ/m number 15
hajo 2w8CnP1hHKVozsC1 encrypted password username
hajo attributes username
type of remote access service
tunnel-group 192.168.178.230 type ipsec-l2l
IPSec-attributes tunnel-group 192.168.178.230
pre-shared-key *.
type tunnel-group SSLClientProfile remote access
attributes global-tunnel-group SSLClientProfile
Group Policy - by default-SSLClientPolicy
tunnel-group SSLClientProfile webvpn-attributes
enable SSLVPNClient group-alias
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:0008564b545500650840cf27eb06b957
: end
What wrong with my setup.
Concerning
Hans-Jürgen Guenter
Hello Hans,.
You should change your VPN pool to be a different subnet within the network, for example: 192.168.5.0/24
Then configure NAT exemption for traffic between the Interior and the pool of vpn.
Based on your current configuration, the following changes:
mask 192.168.5.10 - 192.168.5.15 255.255.255.0 IP local pool SSLClientPool
no_NAT to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
And then also to enable icmp inspection:
Policy-map global_policy
class inspection_default
inspect the icmp
-
I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well
Thank you
interface Ethernet0/0
Speed 100
full duplex
nameif outside
security-level 0
IP x.x.x.x 255.255.255.240
!
interface Ethernet0/1
Speed 100
full duplex
nameif inside
security-level 100
IP 10.88.10.254 255.255.255.0
!
interface Management0/0
Shutdown
nameif management
security-level 0
no ip address
!
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the PAT_to_Outside_ClassA object
10.88.0.0 subnet 255.255.0.0
network of the PAT_to_Outside_ClassB object
subnet 172.16.0.0 255.240.0.0
network of the PAT_to_Outside_ClassC object
Subnet 192.168.0.0 255.255.240.0
network of the LocalNetwork object
10.88.0.0 subnet 255.255.0.0
network of the RemoteNetwork1 object
Subnet 192.168.0.0 255.255.0.0
network of the RemoteNetwork2 object
172.16.10.0 subnet 255.255.255.0
network of the RemoteNetwork3 object
10.86.0.0 subnet 255.255.0.0
network of the RemoteNetwork4 object
10.250.1.0 subnet 255.255.255.0
network of the NatExempt object
10.88.10.0 subnet 255.255.255.0
the Site_to_SiteVPN1 object-group network
object-network 192.168.4.0 255.255.254.0
object-network 172.16.10.0 255.255.255.0
object-network 10.0.0.0 255.0.0.0
outside_access_in deny ip extended access list a whole
inside_access_in of access allowed any ip an extended list
11 extended access-list allow ip 10.250.1.0 255.255.255.0 any
outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1
mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool
NAT static NatExempt NatExempt of the source (indoor, outdoor)
NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3
NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search
!
network of the PAT_to_Outside_ClassA object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassB object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassC object
NAT dynamic interface (indoor, outdoor)
Access-group outside_access_in in interface outside
inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
dynamic-access-policy-registration DfltAccessPolicy
Sysopt connection timewait
Service resetoutside
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto-map dynamic dynmap 10 set pfs
Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1
life together - the association of security crypto dynamic-map dynmap 10 28800 seconds
Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000
Crypto-map dynamic dynmap 10 the value reverse-road
card crypto mymap 1 match address outside_1_cryptomap
card crypto mymap 1 set counterpart x.x.x.x
card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1
card crypto mymap 86400 seconds, 1 lifetime of security association set
map mymap 1 set security-association life crypto kilobytes 4608000
map mymap 100-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
crypto isakmp identity address
Crypto isakmp nat-traversal 30
Crypto ikev1 allow outside
IKEv1 crypto ipsec-over-tcp port 10000
IKEv1 crypto policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 50
preshared authentication
the Encryption
md5 hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
preshared authentication
aes-256 encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal BACKDOORVPN group policy
BACKDOORVPN group policy attributes
value of VPN-filter 11
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelall
BH.UK value by default-field
type tunnel-group BACKDOORVPN remote access
attributes global-tunnel-group BACKDOORVPN
address pool Admin_Pool
Group Policy - by default-BACKDOORVPN
IPSec-attributes tunnel-group BACKDOORVPN
IKEv1 pre-shared-key *.
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
Excellent.
Evaluate the useful ticket.
Thank you
Rizwan James
-
Client VPN connects but not internal LAN access or Ping
Hi all.
I'm new on this forum and kindly asking for your help because I'm stuck.
I have an ADSL router cisco 877 which I configured easy VPN server.
Now the Cisco VPN client ver 5.0 to connect successfully to the VPN server, but when you try to access/ping computers on the internal network, there is no response.The configuration is below. Please let know us where I was going or what I missed.
[code]Building configuration...
Current configuration: 4574 bytes
!
version 12.4
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$ $86dn J8HrK9kCQ8G9aPAm6xe4o1
enable password 7 13151601181B54382F
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login internal_affairs_vpn_1 local
AAA authorization exec default local
AAA authorization internal_affairs_vpn_group_1 LAN
!
!
AAA - the id of the joint session
!
Crypto pki trustpoint TP-self-signed-2122144568
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 2122144568
revocation checking no
rsakeypair TP-self-signed-2122144568
!
!
TP-self-signed-2122144568 crypto pki certificate chain
self-signed certificate 03
30820248 308201B 1 A0030201 02020103 300 D 0609 2A 864886 F70D0101 04050030
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
69666963 32313232 31343435 6174652D 3638301E 170 3032 30333032 32303537
31375A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
4F532D53 5369676E 656C662D 43 65727469 66696361 74652 32 31323231 65642D
34343536 3830819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
8100D3EA 07EC5D66 F4DD8ACC 5540BDBE 009B3C26 598EC99C D99D935A 51292F96
F495E5A9 8D012B0E 73EA7639 3B 586799 187993F5 ED9CA31C 788756DD 6BDB1B2B
4D7AA7F0 B07CF82F F2A29E86 E18B442C 550E22D2 E92D9914 105B7D59 253BBEA1
D84636B4 A4B4B300 7946CE84 E9A63D2E 7789B03A 6ADDB04E B21EC207 CCFEAE0B
30 HAS A 50203 010001, 3 1 130101 301B 0603 030101FF FF040530 0F060355 70306E30
551 1104 14301282 10494E54 45524E41 4C5F4146 46414952 53301F06 03551D 23
04183016 8014FA0F B3C9C651 7FD91EFA 3F63EAE8 6C83C80D 8AE2301D 0603551D
0E041604 14FA0FB3 C9C6517F D91EFA3F 63EAE86C 83C80D8A E2300D06 092A 8648
86F70D01 01040500 03818100 A1026DDC C91CAEB2 3C62AF92 D6B25EB2 CA 950, 920
313BCF26 4A35B039 A4F806A0 8CB54D11 6AF1ABAA A770604B 4403F345 0351361B
E2CF2950 26974F4A 95951862 401A4F76 C816590C 2FFCB115 9A8B3E96 4373FFE1
33D744F7 E0FDDE61 B5B48497 9516C3C6 A3157957 C621668E A83B5E33 2420F962
9142DD9E B6E9D74A 899A 9653
quit smoking
dot11 syslog
IP cef
No dhcp use connected vrf ip
DHCP excluded-address IP 10.10.10.1
!
IP dhcp pool dhcplan
Network 10.0.0.0 255.0.0.0
DNS-server 196.0.50.50 81.199.21.94
default router 10.10.10.1
Rental 7
!
!
property intellectual auth-proxy max-nodata-& 3
property intellectual admission max-nodata-& 3
name of the IP-server 81.199.21.94
!
!
!
VPN username password 7 095A5E07
username fred privilege 15 password 7 1411000E08
username ciscovpn password 7 01100F175804101F2F
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
ISAKMP crypto client configuration group internal_affairs_vpn
key *.
DNS 196.0.50.50 81.199.21.94
pool ippool
ACL 108
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
!
Crypto-map dynamic internal_affairs_DYNMAP_1 10
Set transform-set RIGHT
market arriere-route
!
!
card crypto client internal_affairs_CMAP_1 of authentication list internal_affairs_vpn
card crypto isakmp authorization list internal_affairs_vpn_group_1 internal_affairs_CMAP_1
client configuration address card crypto internal_affairs_CMAP_1 answer
ipsec 10-isakmp crypto map internal_affairs_CMAP_1 Dynamics internal_affairs_DYNMAP_1
!
Archives
The config log
hidekeys
!
!
!
Bridge IRB
!
!
interface Loopback0
2.2.2.2 the IP 255.255.255.255
!
ATM0 interface
no ip address
ATM vc-per-vp 512
No atm ilmi-keepalive
PVC 0/32
aal5snap encapsulation
Protocol ip inarp
!
DSL-automatic operation mode
Bridge-Group 1
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
description of the local lan interface
IP 10.10.10.1 255.0.0.0
IP nat inside
IP virtual-reassembly
!
interface BVI1
internet interface Description
IP 197.0.4.174 255.255.255.252
NAT outside IP
IP virtual-reassembly
internal_affairs_CMAP_1 card crypto
!
IP local pool ippool 192.168.192.1 192.168.192.200
IP forward-Protocol ND
IP route 0.0.0.0 0.0.0.0 196.0.4.173
!
IP http server
local IP http authentication
IP http secure server
IP nat inside source list interface BVI1 NAT overload
IP nat inside source static tcp 2.2.2.2 23 23 BVI1 interface
!
NAT extended IP access list
allow an ip
!
access-list 108 allow ip 10.0.0.0 0.255.255.255 192.168.192.0 0.0.0.255
!
!
!
control plan
!
Bridge Protocol ieee 1
1 channel ip bridge
!
Line con 0
password 7 0216054818115F3348
no activation of the modem
line to 0
line vty 0 4
password 7 06160E325F59590B01
!
max-task-time 5000 Planner
endSince this is a named ACL, you need to change ACL configuration mode:
NAT extended IP access list
Then, make the changes.
Federico.
-
Establish a IPsec VPN connection, but remote site can't ping main office
Hi, I set up connection from site to site IPsec VPN between cisco 892 (main site) router and linksys router wrv210 (remote site). My problem is that I can ping network router wrv210 lan of my main office where is cisco 892 router, but I cannot ping the main site of linksys wrv210 lan (my remote site).
My configuration on the cisco 892 router:
type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-1
game group-access 103
type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-3
game group-access 106
type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-2
game group-access 105
type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-5
game group-access 108
type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-4
game group-access 107
type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-7
group-access 110 match
type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-6
game group-access 109
type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-9
game group-access 112
type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-8
game group-access 111
type of class-card inspect entire game SDM_AH
match the name of group-access SDM_AH
type of class-card inspect entire game SDM_ESP
match the name of group-access SDM_ESP
type of class-card inspect entire game SDM_VPN_TRAFFIC
match Protocol isakmp
match Protocol ipsec-msft
corresponds to the SDM_AH class-map
corresponds to the SDM_ESP class-map
type of class-card inspect the correspondence SDM_VPN_PT
game group-access 102
corresponds to the SDM_VPN_TRAFFIC class-map
type of class-card inspect entire game PAC-cls-insp-traffic
match Protocol cuseeme
dns protocol game
ftp protocol game
h323 Protocol game
https protocol game
match icmp Protocol
match the imap Protocol
pop3 Protocol game
netshow Protocol game
Protocol shell game
match Protocol realmedia
match rtsp Protocol
smtp Protocol game
sql-net Protocol game
streamworks Protocol game
tftp Protocol game
vdolive Protocol game
tcp protocol match
udp Protocol game
inspect the class-map match PAC-insp-traffic type
corresponds to the class-map PAC-cls-insp-traffic
type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-10
game group-access 113
type of class-card inspect all sdm-service-ccp-inspect-1 game
http protocol game
https protocol game
type of class-card inspect entire game PAC-cls-icmp-access
match icmp Protocol
tcp protocol match
udp Protocol game
type of class-card inspect correspondence ccp-invalid-src
game group-access 100
type of class-card inspect correspondence ccp-icmp-access
corresponds to the class-ccp-cls-icmp-access card
type of class-card inspect correspondence ccp-Protocol-http
match class-map sdm-service-ccp-inspect-1
!
!
type of policy-card inspect PCB-permits-icmpreply
class type inspect PCB-icmp-access
inspect
class class by default
Pass
type of policy-card inspect sdm-pol-VPNOutsideToInside-1
class type inspect sdm-cls-VPNOutsideToInside-1
inspect
class type inspect sdm-cls-VPNOutsideToInside-2
Pass
class type inspect sdm-cls-VPNOutsideToInside-3
Pass
class type inspect sdm-cls-VPNOutsideToInside-4
Pass
class type inspect sdm-cls-VPNOutsideToInside-5
Pass
class type inspect sdm-cls-VPNOutsideToInside-6
inspect
class type inspect sdm-cls-VPNOutsideToInside-7
Pass
class type inspect sdm-cls-VPNOutsideToInside-8
Pass
class type inspect sdm-cls-VPNOutsideToInside-9
inspect
class type inspect sdm-cls-VPNOutsideToInside-10
Pass
class class by default
drop
type of policy-map inspect PCB - inspect
class type inspect PCB-invalid-src
Drop newspaper
class type inspect PCB-Protocol-http
inspect
class type inspect PCB-insp-traffic
inspect
class class by default
drop
type of policy-card inspect PCB-enabled
class type inspect SDM_VPN_PT
Pass
class class by default
drop
!
security of the area outside the area
safety zone-to-zone
zone-pair security PAC-zp-self-out source destination outside zone auto
type of service-strategy inspect PCB-permits-icmpreply
zone-pair security PAC-zp-in-out source in the area of destination outside the area
type of service-strategy inspect PCB - inspect
source of PAC-zp-out-auto security area outside zone destination auto pair
type of service-strategy inspect PCB-enabled
sdm-zp-VPNOutsideToInside-1 zone-pair security source outside the area of destination in the area
type of service-strategy inspect sdm-pol-VPNOutsideToInside-1
!
!
crypto ISAKMP policy 1
BA 3des
md5 hash
preshared authentication
Group 2
lifetime 28800
ISAKMP crypto key address 83.xx.xx.50 xxxxxxxxxxx
!
!
Crypto ipsec transform-set ESP-3DES esp-3des esp-md5-hmac
!
map SDM_CMAP_1 1 ipsec-isakmp crypto
Description NY_NJ
the value of 83.xx.xx.50 peer
game of transformation-ESP-3DES
match address 101
!
!
!
!
!
interface BRI0
no ip address
no ip redirection
no ip unreachable
no ip proxy-arp
penetration of the IP stream
encapsulation hdlc
Shutdown
Multidrop ISDN endpoint
!
!
interface FastEthernet0
!
!
interface FastEthernet1
!
!
interface FastEthernet2
!
!
interface FastEthernet3
!
!
interface FastEthernet4
!
!
interface FastEthernet5
!
!
FastEthernet6 interface
!
!
interface FastEthernet7
!
!
interface FastEthernet8
no ip address
no ip redirection
no ip unreachable
no ip proxy-arp
penetration of the IP stream
automatic duplex
automatic speed
!
!
interface GigabitEthernet0
Description $ES_WAN$ $FW_OUTSIDE$
IP address 89.xx.xx.4 255.255.255.xx
no ip redirection
no ip unreachable
no ip proxy-arp
penetration of the IP stream
NAT outside IP
IP virtual-reassembly
outside the area of security of Member's area
automatic duplex
automatic speed
map SDM_CMAP_1 crypto
!
!
interface Vlan1
Description $ETH - SW - LAUNCH INTF-INFO-FE 1 to $$$ $ES_LAN$ $FW_INSIDE$
IP 192.168.0.253 255.255.255.0
no ip redirection
no ip unreachable
no ip proxy-arp
penetration of the IP stream
IP nat inside
IP virtual-reassembly
Security members in the box area
IP tcp adjust-mss 1452
!
!
IP forward-Protocol ND
IP http server
local IP http authentication
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
!
IP nat inside source overload map route SDM_RMAP_1 interface GigabitEthernet0
IP route 0.0.0.0 0.0.0.0 89.xx.xx.1
!
SDM_AH extended IP access list
Note the category CCP_ACL = 1
allow a whole ahp
SDM_ESP extended IP access list
Note the category CCP_ACL = 1
allow an esp
!
recording of debug trap
Note access-list 1 INSIDE_IF = Vlan1
Note category of access list 1 = 2 CCP_ACL
access-list 1 permit 192.168.0.0 0.0.0.255
Access-list 100 category CCP_ACL = 128 note
access-list 100 permit ip 255.255.255.255 host everything
access-list 100 permit ip 127.0.0.0 0.255.255.255 everything
access-list 100 permit ip 89.xx.xx.0 0.0.0.7 everything
Note access-list 101 category CCP_ACL = 4
Note access-list 101 IPSec rule
access-list 101 permit ip 192.168.0.0 0.0.0.255 192.168.7.0 0.0.0.255
Note access-list 102 CCP_ACL category = 128
access-list 102 permit ip host 83.xx.xx.50 all
Note access-list 103 CCP_ACL category = 0
Note access-list 103 IPSec rule
access-list 103 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255
Note access-list 104 CCP_ACL category = 2
Note access-list 104 IPSec rule
access-list 104 deny ip 192.168.0.0 0.0.0.255 192.168.7.0 0.0.0.255
access-list 104. allow ip 192.168.0.0 0.0.0.255 any
Note access-list 105 CCP_ACL category = 0
Note access-list 105 IPSec rule
access-list 105 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255
Note access-list 106 CCP_ACL category = 0
Note access-list 106 IPSec rule
access-list 106 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255
Note access-list 107 CCP_ACL category = 0
Note access-list 107 IPSec rule
access-list 107 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255
Note access-list 108 CCP_ACL category = 0
Note access-list 108 IPSec rule
access-list 108 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255
Note access-list 109 CCP_ACL category = 0
Note access-list 109 IPSec rule
access-list 109 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255
Note access-list 110 CCP_ACL category = 0
Note access-list 110 IPSec rule
access-list 110 permit ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255
Note access-list 111 CCP_ACL category = 0
Note access-list 111 IPSec rule
access-list 111 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255
Note access-list 112 CCP_ACL category = 0
Note access-list 112 IPSec rule
access-list 112 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255
Note access-list 113 CCP_ACL category = 0
Note access-list 113 IPSec rule
access-list 113 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255
not run cdp
!
!
!
!
allowed SDM_RMAP_1 1 route map
corresponds to the IP 104
--------------------------------------------------------
I only give your router cisco 892 because there is nothnig much to change on linksys wrv210 router.
Hope someone can help me. See you soon
You can run a "ip inspect log drop-pkt" and see if get you any what FW-DROP session corresponding to the traffic you send Linksys to the main site. Zone based firewall could be blocking traffic initiated from outside to inside.
-
ASA Cisco IPSEC VPN tunnel has not managed the traffic
Hi guys
I am trying to set up a new connection IPSEC VPN between a Cisco ASA 5520 (verion 8.4 (4)) and Checkpoint Firewall. I managed to establish the phases IKE and IPSEC and I can see the tunnel is UP. But I can't see any traffic through the tunnel. I checked the cryptomap both ends and try to test with a contionuous ping from within the network of the SAA.
I made a screenshot of ICMP packets but cannot see in ASA. I welcomed the icmp inside ASA interface.
I did a package tracer and it ends with a fall of vpn - filter the packets. But can not see any configured filters...
Your help is very appreciated...
Thank you
You probably need to add nat negate statements:-something like.
object-group network OBJ-LOCAL
Network 10.155.176.0 255.255.255.0
object-group network OBJ / remote
object-network 192.168.101.0 255.255.255.0
NAT static OBJ-LOCALOBJ-LOCAL source destination (indoor, outdoor) static OBJ-REMOTE OBJ-REMOTE-no-proxy-arpYou are running 8.4 nat 0 has been amortized
Maybe you are looking for
-
My Mac system preferences won't allow me to update my iCloud password
I cannot change my password to iCloud my Mac system preferences. There is no preferences available in iCloud system. I recently had to change my Apple ID due to a possible hack. I changed my Apple ID on all my other devices and updated my ID to iCl
-
Satellite P300-1FN: CD/DVD drive problem - can not read the DVD game
Hello My brand-new Satellite P300-1FN loaded some software using the DVD player ok, but now when I put any disk in is not automatically run, but the drive seems to run to the top and then a pop up tells me after going computer-> DVD player to get acc
-
I have the computer hp laptop pavilion dv7 4150er, running on windows 7 64 bit. There no short DST when I ran boot and run in trials with the same ID RK47G1-6AH6LK-9C5V7A-60TP03 with "hard disk 1" in the description. Any ideas what's past? See you so
-
Update of the modules of RAM for my desktop pc
I want to buy G.Skill Ares RAM for my HP Pavilion G5460uk. The specs are below the RAM Model number
-
What Version of SATA has the motherboard ASUS M2N68-(Narra2)?
Hello I want to improve my HP a6150de with a SSD desktop PC.I'm not in a position to know what SATA version (1, 2 or 3 GB of a.k. 1.5/3.0 or 6.0) comes with my ASUS M2N68 - Map (Narra2) mother. I have tried several hardware analysis tools, also check