iPad connects to the cellular service

Similar Questions

• My pro iPad connects to the WIFI, but loses connectivity to drops in use.  My other IOS devices (iPhone, macbook, etc.) do not have this problem.  Ideas to solve?

  My pro iPad connects to the WIFI, but loses connectivity to drops in use.  My other IOS devices (iPhone, macbook, etc.) do not have this problem.  Ideas to solve?

  Hello BrooklynWM!

  I definitely want my iPad to stay connected to the Wi - Fi connection while I use it.  Thanks for posting that other iOS and OS X devices have no problem with the connectivity dropping.  We can try a few things.

  Would first go through the steps listed in this article: If your iPhone, iPad or iPod touch connects to a Wi-Fi - Apple Support Network

  Then if it does not help, you can check network settings with this: recommended for the WiFi routers and access - points Apple supported

  After trying those, if you still see the drop connectivity, make sure the iPad Pro is updated with iOS 9.3.2 and check to see if the connection when you are in a certain place, time, or one event happening elsewhere in the House.

  Best regards.

• Unable to connect to the web services server

  Unable to connect to the web services server.  It is a common error that you might see if you try to enable web services.  If you receive this message, try the following steps.

  For Officejet printers

  1. open the internet browser type printer IP address.

  2 should bring you to the status of the printer page.

  3. Select the tab network at the top.

  4. left side select IPv4 under wireless.

  5. under DNS address Configuration select manual DNS server.

  6. for favorite enter 8.8.8.8

  7. for alternate enter 8.8.4.4

  8. Select apply. You can get a warning saying that this could break the connection which is very good.

  9. turn the printer off for about 30 seconds and then try to enable web services.

  For Photosmart printers

  1. Enter the printer's IP address in a browser.

  2 Select the network at the top of the page.

  3. on the left, select network.

  4. Select Network (IP) address

  5. select manual DNS server

  a. manual Preferred DNS should read 8.8.8.8

  b. alternate DNS server should read. 8.8.4.4

  6. Select apply you could get a fair warning select OK

  I hope this helps!

• Pavilion 140 550 - t: unable to connect to the windows service

  Not sure if it's the good advice of post, but here goes.

  Just got the HP computer yesterday and installed Norton Security, Malwarebytes, and Windows Live Mail (do not like the version of Mail). Now, when I start it, I get "Unable to connect to the Windows Service" pop up and WLM crashes when I try to open it. What the DEVIL?

  Had the same problem on the one I just replaced. My laptop became the 'Group Policy' error thing, but I think I fixed it.

  Any suggestions? Windows is a joke!

  If it is Norton Security, then it's a firewall as well and firewalls blocking things, it's that they are supposed to do. So demand for three, you said that this is probably the cause.

  But if you do not want to test it, then try the system restore I've mentioned or reload the image origin, then just put in place the email again and see if it works without the other two installed, first to see if it will work with anything else in the picture.

• Unable to connect to the wifi service in my house, how can this be repaired?

  I have a dell laptop and I am trying to understand how to do this.  I enter the key of the service network and the message says that the network password must be 40-140-bit according to your network. It can be entered as ascii characters 13-5 or 10-26 hexadecimal characters? How can this be repaired?

  Hi Vickiloo06,

  ·         Did you do changes on the computer before the show?

  ·         What happens exactly when you try to connect to the wifi service, you receive error message?

  I suggest you to consult the following Microsoft Knowledge Base article and check if it works.

   

  Unable to connect to an access point wireless with Wi - Fi Protected Access update installed

  http://support.Microsoft.com/kb/821442

   

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  http://support.Microsoft.com/kb/870702

  I hope this helps.

• The same day as my expired Norton my internet connection icon says... unknown internet connection. The dependency service or group was able to start.

  the dependency of the orgroup faaied to start service unknown Internet connection.

  The same day as my expired Norton my internet connection icon says... unknown internet connection. The dependency service or group was able to start. I tried all the suggestions on this page. Can't even find the virus that the internet not connected. My livebox is grateful for the laptop please help

  Hello

  ·         You will remember to do recent changes on the computer before this problem?

  ·         Is the question only for the icon network did you try to open a Web page and check?

  ·         What suggestions do you have tried?

  ·         What is the exact error message?

  ·         Have you tried all the steps from the link?

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-networking/connection-status-unknown-the-dependency-service/92203623-b6d5-4301-8c79-00210abbcdd4

  I suggest you follow the steps mentioned below:

  Method 1:

  Follow the steps in the link and check if the problem persists:

  http://support.Microsoft.com/kb/943996

  Registry warning:

  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the link below to follow the steps to back up registry:

  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 2:

  If the previous step fails, follow the steps in the link and check if the problem persists:

  http://support.Microsoft.com/kb/936211

  Method 3:

  If the previous step fails, reset WinSock and check if the problem persists:

  http://support.Microsoft.com/kb/811259

  Registry warning:

  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the link below to follow the steps to back up registry:

  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 4:

  Temporarily disable the norton software (and any other security software) and the firewall on the computer as a test and check if this solves the problem follow the link below:

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  If disabling the antivirus software solves the problem, you may need to configure the settings of the antivirus as a result program.

  Note: make sure that you enable the antivirus software, other security and firewall programs.

  Warning: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

• Vista problem: "failed to connect to the windows service, Windows cannot connect to the system event.

  I have reported this problem on my PC at home that connects to the internet. My laptop runs Vista Home Premium and I can't connect to the internet. I took my laptop on a trip, tried to connect to the wireless network that was free to the place we are. Could not connect, and after this initial test, the following is displayed after the start of "failed to connect to the Windows Service, Windows cannot connect to the system event notification service. This problem prevents limited users to logon to the system. As administratvie user, you can view the system event log to see why the service did not respond. "(have no idea how or what it means) when I go to the task bar you want to connect to a network, it is said:" the dependency service or group could not start"and if I go ahead and press"connect to a network"it says it can't find.  I search for computers on the network (who I'm sitting next to) and then try to diagnose the problem and it cannot. I have limited knowledge of this type of problem. Anyone have this problem and how to fix it?

  Hi ptkein,

  Thanks for posting your question on the Forums of Windows Vista.

  Option 1: You can download and install the latest network card drivers and see if that can solve the problem.

  Option 2: Follow the link below to fix network connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Option 3: Follow the link below to solve Internet connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Option 4: To verify if a third party application is a cause, follow this link (http://windows.microsoft.com/en-us/windows-vista/Advanced-startup-options-including-safe-mode) for this boot to the desktop using the safe mode with networking option and try to install the network. If the problem is resolved, you will need to perform a clean boot by following the steps in the following article to refine the exact source and isolate it: http://support.microsoft.com/kb/929135

  Let me know if it worked.

  Hope it will be useful.

  Thank you and best regards,

  Kadoch - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows 8 could not connect to the Customer Service of group policy on my HP Pavilion

  We recently purchased a HP Pavilion laptop g6 C7C77UA #ABL with 8 64-bit Windows. It seemed to work fine until a week ago (we only had it for 2 weeks). I can access the computer through my user that I'm the system administrator, but my husband try to click on the user whenever he has a message that appears saying Windows cannot connect to the customer service group policy, please see your system administrator. He could access his side in all first, we bought the computer.

  I did troubleshooting and it comes up saying that Windows Firewall is configured incorrectly. I tried to go in the windows firewall, but it is not letting me, he just guard spinning and finally said that he does not.

  So far, I like my HP Pavilion, but I'm about to throw it out the window because of Windows 8. Please help me! Thank you!

  Hello m-oickle,.

  Take a look at this document, which covers aspects of the restoration of your laptop.  Please let me know if the troubleshooting steps to help you solve your problem.

  Good luck!

• problem connecting to the web services server

  I tried to download the latest updates of software/firmware for my all-in-one HP Photosmart Prem C310a.

  I can't get updates or activate Web Services because it still gives me the error message "problem connect to the web services server.

  I tried everything in the section of the Web of HPs site including connection via WPS - unsucessfully problems.

  I understand that you have found impossible to connect to the server error message on your printer. I would first disconnect the router and the printer for about 1 minute. I would plug the router first then the printer. I would then try to enable web services. If not successful, and you get the same error message. I'd follow these steps.

  1 obtain the IP address of your printer
  a. This can be done by pressing the icon on the printer wireless.
  2. Enter the printer's IP address in a browser.
  3. Select the tab network at the top of the page.
  4. on the left, select network.
  5. Select Network (IP) address
  6. select manual DNS server
  a. manual Preferred DNS should read 8.8.8.8
  b. alternate DNS server should read. 8.8.4.4
  7. Select apply you could get a fair warning select OK.

• Failed to connect to the JMX service (209,1046) when you try to view the logs in PeopleTools 8.55

  I am trying to use the new functionality of Log Viewer PeopleTools 8.55.

  It is a great improvement that allows developers/testers/support team members to display the application server logs, process scheduler logs and newspapers PIA; with a regular account of the PeopleSoft Application.

  You have no need to create a system account on the server (Linux or Windows) for users to view the logs.

  I managed to configure the Web server log viewer, but when I try to Application I can see message failed to connect to the JMX service (209,1046).

  
  

  When I configure the JMX for APPDOM user, I tried PTADMIN with no success.

  
  

  Could someone describe the process to change the JMX user for Tuxedo domain?

  
  

  Thank you

  Stéphane.

  the default installation of DPK password is password.

  Kind regards

  / Stéphane.

• "Sorry, we could not connect to the Microsoft services right now. If the problem persists, look for 'referee' on the start screen.

  "Sorry, we could not connect to the Microsoft services right now. If the problem persists, look for 'referee' on the start screen.

  This appears when I try to connect with Microsoft Account.

  I tried all the possibilities that was displayed in the link but when even the problem exists... below you please suggest me the solution to add the microsoft account

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-networking/sorry-we-couldn

  Hi Nikhil,

  If you connect through a proxy, then I suggest you to try the steps suggested in this article and checking:

  http://support.Microsoft.com/kb/2778122/en-us

  Keep us updated on the results.

• air application connects to the web service although swf don't

  Hey there,

  I will try and be brief. We built a kiosk application in flash builder a pure as3 project. When we went to convert it into an air application all seems fine except for two issues. one is that we cannot use the Security.allowDomain("*"); Tagus. not much we comment on this possibility, but when we do we cannot connect to the web service that we use. Here is the error msg that we get:

  URL http://api.macys.com/v2/catalog/product?prodid=559529 & prodid = 586262 & prodid = 442702 & prodid = 5 39030 & prodid = 444331 & prodid = 593389 & prodid = 102435 & prodid = 519743 & prodid = 357571 & prodid = 128285 & prodid = 407708 & prodid = 209799 & prodid = 417917 & prodid = 498705 & prodid = 131858 & prodid = 597478 & prodid = 142166 & prodid = 470687 & prodid = 584020 & prodid = 167015 & prodid = 75190 & prodid = 432111 & prodid = 481224 & prodid = 549755 & prodid = 483429 & prodid = 414178 & prodid = 596422 & prodid = 385591 & prodid = 226280 & d = 142163 prodi

  ioErrorHandler: errorProductId: WebApplicationException

  ioErrorHandler: currentTarget: Error #2032: error in workflow. URL: http://api.macys.com/v2/catalog/product?prodid=559529 & prodid = 586262 & prodid = 442702 & prodid = 5 39030 & prodid = 444331 & prodid = 593389 & prodid = 102435 & prodid = 519743 & prodid = 357571 & prodid = 128285 & prodid = 407708 & prodid = 209799 & prodid = 417917 & prodid = 498705 & prodid = 131858 & prodid = 597478 & prodid = 142166 & prodid = 470687 & prodid = 584020 & prodid = 167015 & prodid = 75190 & prodid = 432111 & prodid = 481224 & prodid = 549755 & prodid =. 483429 & prodid = 414178 & prodid = 596422 & prodid = 385591 & prodid = 226280 & d = 142163 prodi

  Here is the error of charles:

  < error >

  < > 103 errorCode < / errorCode >

  types of arguments < message > Incorrect or combination < / message >

  < errorDetail > WebApplicationException() < / errorDetail >

  false < success > < / success >

  < / error >

  now, if we run just the swf file it connects very well. the only reason I need this app to be in a wrapper of the air is so that I can remove the print dialog box. otherwise, I'd create just an exe file.

  any ideas would be great!

  Thank you

  OK, found the problem!

  When we built the as3 project and we implement web service calls, we used post from get we caused problems. We have been connecting to a service of qa so that may have something to do with it. In all cases, we have changed the headers in the air application to get and it seems to work fine. Why would he works in the SWF and not the air who knows, but there are go!

  Thank you

  Jorge

• After briefly losing service, iPhone will fail to connect to the cellular network until you restart

  When my iPhone lose service for any period of time, as when he drives through an area that is not covered or go inside a building, unit reverts to the cellular network once he's back in the range. I tried to switch the plane made to make additional research; It does not work. I tried to reset network settings. It doesn't work and now I have to re - enter the password for each network wifi (disappointment).

  The fix, however, if I turn the unit completely off and the power supply back on. Only to reappear again the next time that I lose the service.

  What in the world is the cause and what can do about it?

  Things to note: MRI comes back fine. Issue JUST started this week. Device has been restored there is from a backup about 3 weeks because it is a replacement for one that I destroyed.

  Post edited by: Hydrochlorick

  I can confirm the exact behavior that you are experiencing.

  My iPhone brand new T-Mobile SE (1 week) did not have this problem on iOS 9.3.5. He found his connection to my mobile operator without any problem before the iOS 10 update.

  I also tried all the things (airplane, network reset mode, etc.) that you tried. Will not fix it. The only thing coming back my cellular service is to power cycle the phone.

  It's a real problem for me as I work in a story 72 building (no service in the elevator) and I have unfortunately to enter and leave the building a certain number of times per day.

  You have not specified what iPhone model and what version of the OS. Can you clarify?

  Thank you

  -RMT

• Unable to connect to the Web Services Proxy/unused (a HP 7500 JO)

  Hello

  Here's the situation:

  Previous installer:

  .  I have connected my 7500 for the corporate network (IP = 172... series)

  .  registered the product with ePrintCenter

  .  used a PC under Windows to print (and scan) with the printer

  .  web proxy entry "webproxy.phila.gov".

  .  However, because homeland security rules, I could never work, so I just let it go

  Current situation

  .  has taken the home printer and set up on my home network, i.e.,.

  -using the 192.168.xx.xx series

  -Router broadband Netgear ' G' (1 years) set up at the 192.168.xx.254

  -SSID & encryption assigned

  -printer, the value 192.168.xx.155 (static IP address, the subnet and the gateway assigned as well)

  -My DNS is identical to the bridge and it works fine for all the internet access to this day

  -with the help of a PC and a Macbook Air to print and scan and everything works fine

  .  HOWEVER,.

  -Initially, 'web services' were active (carried over from when I was on the company neetwork?)

  ..  Are looking for, found and downloaded updates

  -When I went to hp.com ePrintCenter he showed the product as 'registered '.

  ..  He would'nt I would like to connect (with a name and a password I had used previously), or create a new account

  ..  I never remember getting an email address of the printer

  ..  and I had never been able to send anything to the printer to print because of my problem of network security

  -Yes, after trying all sorts of things, I:

  ..  I tried to get another email without success

  ..  tried to re - enable web services, but he said I need to 'proxy', and I discovered that he had always "webproxy.phila.gov."

  ..  I have reset the values by default web services and network values

  ..  I put the static IP address return address in (i.e., printer, subnet and gateway (it has nowhere to put in a DNS one))

  ..  printing and scanning to 192.168.xx.155 works fine

  ..  From my iPad AirPrint works very well

  .  BUT, I still can not online and therefore web server, web services are not enabled, therefore not ePrint

  -everytime I try, it says it needs a proxy

  - but I don't have a proxy installed on my internal home network bit

  -Comcast/Xfinity, my ISP, do not use a proxy

  So, I'm dead in the water.  I can't figure out how to get the web services enabled; I do not use a proxy, so I don't know how to go beyond this issue. How to regenerate address of the printer; and so, how do I connect an account on the ePrintCenter (or get them to send me my old account information).  I'm dead in the water and cannot use a feature most of my printer that I desperately want to be put in place and functional.

  Any help would be greatly appreciated!

  Tommy

  Problem solved, but I don't know exactly how I did it. However, I went back in and let the printer assign the IP address. Then I turned the printer off and on again. Last I kept pressing the button "Printer e-mail address", who has repeatedly failed, but then finally went through and print the 'printer' page, I quickly used to connect to the ePrintCenter and put everything in place.
  
  Now it's working.

• iPad connects to the network, is unable to connect to Internet

  Received my new iPad. Automatically, it connects to my home network but does not connect to the Internet. I rebooted the router and the iPad, but the same thing. Same problem with the old iPad. That is what it is?

  Hello. When you go into settings > WiFi and tap the current network, that see you the IP address and other network settings, or they are all empty? You use DHCP to configure?