iPhone 5 s microphone will not work when recording video with back camera.its a noise

Similar Questions

• iPhone 5 s microphone does not work during phone call

  Hello! My iphone 5s works really well, sensors, speaker, camera, all right. Similarly, the microphone works really well when I make a call using 'whassapp', 'line', etc and I can record video, talking to Siri, using voice memo and once more my microphone works really well. BUT! When I make call and receive phone call my microphone does not work, they do not hear my voice at all. What will happen with my microphone when you use the cell phone call? HELP ME PLEASE!

  Try resetting your device. This will not erase your data stored on that device.

  • Press and hold the sleep/wake button
  • Press and hold the Home button
  • Press and hold both buttons until the display turns off and on again with the Apple logo on the subject.

  Alternatively, you can go to settings - general - reset - Reset all settings

  If that doesn't work, restore your device to factory settings. Please note that this will delete the data on your device.

  Take a look this Apple Support article: use iTunes to restore the iPhone, iPad or iPod to factory settings - Apple Support.

  As a final step, try recovery mode. Turn off your unit, then plug it to your computer with the hold home button. Hold down Home button until you see the logo of iTunes on the screen of your device. After that on your computer, you should see the iTunes window saying that your device needs to be restored to factory settings. Click Restore.

  More info here:

  https://support.Apple.com/en-us/HT201263

  If these steps do not work, contact Apple and ask for help.

  https://www.Apple.com/support/iPhone/contact/

• Microphone does not work when the headset is connected (Windows 7 with Realtek HD Audio).

  I am a user in advance, but this got to be one of the funniest problems ever. First, I had 2 headphones with microphone.

  1. An old helmet specified with microphone
  2. A new headphones A4Tech HS-100 with microphone that I just bought

  Problem:

  • Using the new helmet I bought, when I plug the microphone (pink jack even) it works, but also when I plug in the headphones (same headphone jack), the microphone no longer works (cannot receive all the sounds, even if it is detected clear as already plugged) and only the work of helmet.

  The most funny thing is:

  • The old headset works fine when I plug the microphone (jack Pink) and headphones (headphones) to my ASUS N81V laptop.
  • When I plug the microphone on my laptop and plug the headphones to my iphone, the microphone and the headphones work!
  • To experiment more, my laptop has a HDMI output connected to an external HDMI monitor, when I connect the microphone on my laptop, only it works, but as soon as I connect the headphones to the headphone jack on the external HDMI monitor, the microphone works again!

  Things, I tried and does not work:

  • Maximize the microphone amp
  • Separate entry made in the audio Panel
  • Ensure the microphone is not dumb anywhere
  • Install the latest drivers from the manufacturer and realtek Web sites

  I want to get both my mic and headphones works when plugged the laptop, what exactly is the problem? Any help? Thank you very much.

  I have a similar problem with my netbook a built-in microphone running Windows Starter, that's how mine to get the fix:

  Control Panel - his - recording tab - click on Configure button - set up micro - Configuration of the Microphone Wizard.

  You'll see three choices 1. Headphones Microphone 2. Table microphone 3. Others.

  All what I have to do to fix my netbook is to select the desktop instead of headphones with Microphone Microphone (it has been revived somehow).

• Satellite A200 28H: F6 floppy will not work when installing XP

  Hello

  I am trying to install Windows XP pro on my new laptop (Satellite A200 28 H), and since it needs driver SATA, I downloaded the driver suitable for my laptop (Satellite A200 28 H), put it on a floppy disk for use with a USB floppy drive (which works fine), press "F6" when appropriate and everything... But it simply doesn't. I had training as a technician for a few years, so even thouh that is no longer my work and I might be a little rusty, I think I still know at least a little what I do... Well, apparently I'm more image than I thought!

  I've tried several things, and this is what I get:

  * If I don't use all the disks, Windows XP will not find the hard drive. Which was intended, no problems here, don't except for the fact that it is completely useless for me :)

  * If I force the driver on the floppy disk, despite Windows tells me that is already a driver that can be used, then within 10 seconds I get a BSOD with the stop message 0x7B (found or inaccessible boot device).

  * If I use the floppy drive, but do not force the driver and listen instead of Windows ("oh, you already have a driver? ("OK, then, use and too bad that diskette"), I can actually finish the installation process. Windows will copy all the necessary files on the disk, it will even restart correctly after that and moved on. But when the installation is complete, the computer will restart, I'll see the loading for a second screen, and then, BSOD stop 0x7B again.

  I'm sure I downloaded the driver for my computer. In fact, I also tried a couple of bad drivers too, just to be safe (IE I use Intel Matrix for ICH8M, but I also tried the ICH7M to be sure), I tried with drivers downloaded from the Toshiba site, on the site of Intel and whatnot-other-website-for-newbies-or-powerusers, and I still have the same behavior as described above.

  I tried partitioning / formatting during installation, and I also tried leaving the file system intact. If I do the latter, the only difference is that I have offered 2 possible OS to boot from, the two being Windows XP and both failed miserably.

  It's probably worth mentioning that, if I use the recovery DVDs and start over and clean with Vista, I have no problem whatsoever, except for the loaded gazillion process during startup, the RAM already used half and applications useless hundred I don't give a darn on... And the fact that some applications that I need work just can not be installed on Vista.

  If anyone has any idea how to solve this problem, I would be very grateful!

  Hello

  The procedure, including the SATA drivers in Win XP using the external USB floppy drive is very easy.
  First you need to download the Storage Manager and having to put on the diskette.

  During the installation of Win XP you must press F6 for inclusion since the external floppy drive and follow the new instructions on the screen.

  _Note; _
  Very important is that your XP CD Win would contains SP2!
  Without SP2 a BSOD can appears and could break up of installation!

  Don t format or don t create all partitions after the installation of the SATA driver. It can erase the installed and included from HARD disk SATA driver.

  Last but not least some readers of external floppy drive are not supported. I read that some users had some problems with an external FDD drives they tested another drive and it worked finally

  Check the recommendations may indicate that it might be useful

  Good bye

• My CAD U37 USB Microphone will not work supposed to be Plug-And-Play.

  I recently bought the microphone she appears under windows 7 as 'C-Media USB Audio Device' as it is supposed to, but it can't find the drivers. I talked to the developers, and they said that it meant to be plug-and-play drivers are native to windows.

  I plug it into my laptop which is running XP and it works very well.

  I tried all usb ports I have, I unplugged everything just got the mouse/keyboard and the monitor.

  Nothing seems to work, please help.

  Hello

  Please contact Microsoft Community.

  I suggest you follow the suggestion provided by Rajesh Govind responded on 19 March 2013 from the link below and check if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-hardware/my-headset-microphone-not-working-in-Windows-8/f4f1ad12-E7EA-4FFB-ac88-df5eed3298e6

  Hope this information was helpful and let us know if you need more assistance. We will be happy to help.

• Satellite A120: Microphone does not work when the power cable is unplugged

  I have a Toshiba Satellite Pro A120, which has just begun to play up...

  I regularly record music of my DJ Mixer in microphone of my laptop entry, recording in Adobe Audition.

  Because the power supply makes a buzzing sound, I can't register with the power cable plugged... If I always record with the unplugged power cable, running off battery.

  I've never had any problems before, but what has caused the problem, I now, was earlier the battery ran out while recording, put the laptop into hibernation mode.

  Since then, I can't register with the power cable disconnected. He recorded only with the cable - which is not a good cause snoring.

  It is not a problem with hearing, because in Windows Vista its implemented the problem proved too. As soon as I unplug the power cable, microphone disappears from view.

  I used to work in IT support, so I'm not a technophobe - but I can't for the life of me works why it would suddenly start to occur, power is not related to the entrance it is micro... !

  One of you lovely people have ideas? I checked power options and the Device Manager to see if theres no hardware issues, but there isn't.

  I also reinstalled my sound card drivers.

  It's strange. I guess you tried a boot cold fresh. Hibernation can sometimes cause problems with the devices.

  Try to update the BIOS.

  If all else fails, you may need to reinstall Windows. (Backup your data and run recovery by holding down the button reset during power on)

• description interface LabVIEW node will not work when compiling

  Hello

  I have a vi that seeks VISA resources and focuses on their name of the interface to select that you connect to.

  I have a strange problem where, if I run the vi in labview it works fine. When the vi is compiled into an exe file, it does not work.

  I traced the problem to the property node "name of Inst Intf' which gives the description of the interface. In Labview, the node of this property returns the description of the interface, as expected.

  When I compile the vi, this node property returns empty strings.

  The station nearest you, that I could find to this kind of problem is it

  http://forums.NI.com/T5/instrument-control-GPIB-serial/why-visa-property-interface-information-inter...

  However, the exe is running as an administrator, so I don't think it's a problem with permissions.

  Any help would be greatly appreciated.

  I have no idea of what was the cause, but I uninstalled the device drivers for the hardware I used, reinstalled and then restarted the computer and now it works fine.

• computer Dell laptop will not work when using battery

  Original title: my pc dell 1564 model. Act when I remove the battery (with adapter only), but when I fix the battery, it is not turn on

  my pc dell 1564 model. Act when I remove the battery (with adapter only), but when I fix the battery, it is not turn on

  Hello

  It is best to get the laptop battery checked from Dell or a local technician. It seems that the battery is dead and does not load when you insert it into the laptop.

  However, you can try to update all drivers installed on the laptop (including the motherboard) and check if it makes a difference.

  http://Windows.Microsoft.com/en-in/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Navigate through the common troubleshooting steps of http://www.dell.com/support/troubleshooting/us/en/04/KCS/KcsArticles/ArticleView?c=us&l=en&s=bsd&docid=266588

  http://FTP.Dell.com/DIAGS/R66243.htm

  Hope this information helps. If you have any questions, please let us know.

• VIMEO WIDGET DOES NOT WORK WHEN DISPLAYING VIDEO IN LANDSCAPE MODE WHICH JUMPS TO THE NEXT BREAKPOINT.

  Hello I had a lot of problems to make Vimeo to work with Responsories between my fluid breakpoints - I have defined it 360, 768, 1024 and 1020 breakpoints. What is happening is when using built in widget Vimeo muse and adjust the widget between breakpoints and then download the site, the widget allows to be played when the phone is held in normal use portrait video. When I'm on my iPhone 6 more, for example, the site load very well with the breakpoint 414. The fines of the video is played. However, then I tilt the phone in landscape mode, the video stops and breaks site for the next breakpoint. I managed to get one or two videos work very well on my site, but others have the same problem above.

  On the page below the first video works very well--you can tilt the phone in landscape mode and it continues to play as usual - on the other two videos - it doesn't - the video stops / site goes to the next breakpoint 768.

  http://www.dubaicorereviewapp.com/guests.html

  What I can not understand, that is why the first video work and not the other two. I tried to create pages with scaled down the content to see if I can get the video to work right and it doesn't. This used to be an issue with Muse before the new version of reagent. Because my site has lots of one type of the members of videos I need to find a way to deal with this issue? all suggestions/guidelines would be appreciated. I did the widget extend to the width of the browser in each of the stitches if that helps.

  
  

  WORKS WITH THIS VIDEO
  

  
  

  
  

  
  

  BUT NOT WITH THIS
  

  
  

  

  
  

  
  

  UPDATE!

  
  

  OK made some progress on this issue - but its not the solution I want - I think that what is happening is when you use the widget to say about 1200 downtime and scale down to each of the lower stop points - you this question - BUT if you copy the widget into the offending breakpoint and hide the original widget and then paste the widget of the memory - so it works very well in this breakpoint - I suspect that there is a bug with the widget / Muse because it works when the SAME scale inserted widget between breakpoints and will work if you paste a widget FRESH in the offending breakpoint - this should be fixed!

  Hi cheeky71,

  This is certainly a bug with Muse and we hope that it be corrected in a future release. I'm glad to hear that you have found a workaround for now.

  Anna

• Windows Vista product key will not work. I checked with Microsoft and they said, that it is used.

  My activation key # does not work. It came with a disk and key * removed product key *. I just checked, and Microsoft said it has been used. Could you send me a key # likely to work or simply to activate my vISTA HOME PREMIUM 32

  original title: Activation key #.

  It's probably normal - it IS used by your previous installation

  You use telephone activation

  telephone activation.
  Click the Start button
  in the search box, type
  SLUI 4
  and press the Enter key
  Follow the instructions - but when asked which service you need the ansafone phone, don't answer - it should oblige the operator to answer, who can deal with you.

  You can also post a full report of MGADiag here, and we can advice a little more precisely what may be the problem...
  To analyze and solve problems for Activation and Validation, we need to see a full copy of the report produced by the MGADiag (download and save to the desktop - http://go.microsoft.com/fwlink/?linkid=52012 ) tool
  Once saved, run the tool.
  Click on the button continue, which will produce the report.
  To copy the report in your response, click the button copy in the tool (ignore the error at this stage), and then paste (using r-click and paste or Ctrl + V) in your response.
  -* in your own thread *, please
  Please also state the Version and edition of Windows cited on your COA sticker (if you have one) on the case with your machine, but do NOT quote the key on the sticker!
  http://www.Microsoft.com/howtotell/content.aspx?PG=COA

• Full screen does not work when watching video clips of type 'tube '.

  When I look at a tube clip video (You Tube, etc.), the function full screen gives me just a white screen but I can hear the clip still running. When I reduce the screen to normal size, all right. This problem started recently. During the last many years I have never had a problem with mode full-screen, just recently.

  I think it's a matter of adjustment, but I don't know where to start. The only things that have changed recently are MSN automatic updates normal and I did an update on my video card, but I don't think that I changed settings. My NVIDIA Media Center has a new look for her, but I don't know if this is part of the issue or not.

  It was suggested by someone to update my Adobe Reader information, but that did not help or anything harm.

  I can provide more details on my monitor or video card if anyone thinks that this could be part of my problem.

  Then, thanks to anyone who can provide a solution or suggestion on how to get my computer to display full-screen video clips again.

  ranfin

  When I look at a tube clip video (You Tube, etc.), the function full screen gives me just a white screen but I can hear the clip still running. When I reduce the screen to normal size, all right. This problem started recently. During the last many years I have never had a problem with mode full-screen, just recently.

  I think it's a matter of adjustment, but I don't know where to start. The only things that have changed recently are MSN automatic updates normal and I did an update on my video card, but I don't think that I changed settings. My NVIDIA Media Center has a new look for her, but I don't know if this is part of the issue or not.

  It was suggested by someone to update my Adobe Reader information, but that did not help or anything harm.

  I can provide more details on my monitor or video card if anyone thinks that this could be part of my problem.

  Then, thanks to anyone who can provide a solution or suggestion on how to get my computer to display full-screen video clips again.

  ranfin

  =====================================
  Looks like the update of the video driver could be the problem.

  Might be interesting to try to uninstall it, or possibly make a system
  restoration of a while before you install.

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• Please help, I've updated my iPad has a few days, but by exploring my camera I discovered that the front camera did not work while the main or back camera is not working properly, please, anyone with a secure solution please share.  Thank you

  I have tried everything that I could even, to the extent where I hard reset my device, but that it does not work, no possible solution please share with me, that I will accept it gladly. Thanks in advance.

  Already restore you factory? If this is not the case, try this. If you have, or it did not help the cause can be hardware partner. Take it to your local Genius Bar or Apple authorized service provider. -AJ

• Webcam & microphone will not work on Satellite C660

  My webcam and microphone have recently stopped working. Satellite C660-1F1 model.

  If someone could help me sort what would be great.

  After reading this description of problem a single sentence, it is not easy to tell when he is the problem.
  We don t know what can be the reason for this.

  Have you done all that can be responsible for this problem?

  Try to roll back OS to an earlier time using System Restore option. Maybe this will help.

• bookmarks and other tools will not work when you click on

  nothing happens when I click on the items on the bar including the bookmarks tool. If I restart the program sometimes it will work for awhile.

  Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox/tools > Modules > appearance).

  • Do NOT click on the reset button on the startup window Mode without failure.
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• Windows Update fails to install KB2539636, KB2468871, KB2533523. Will not work when installing manually or the other.

  I tried to make these updates manually, but they don't always work. I run Windows Vista 32-bit. Despite receiving an error message when installing updates via Windows Update or manually, when I go to the stop, the icon to install the updates always appears next to the stop button. I click to install updates day and then stop, but when I start my computer again the icon is still there, which indicates that they have not installed correctly.

  Manually update an error message of "> Code update here< does="" not="" apply,="" or="" is="" blocked="" by="" another="" condition="" on="" your="" computer.''="" is="">

  When trying to update by using Windows Update, it seems that everything is going as it should (the update is downloaded, it is made a point of restoration etc.) but after they have finished installing, I get an error message in the sense of "updates not installed correctly. An unknown error has occurred. ».

  This is the first problem I had with the Windows updates. Can anyone help?

  Thank you very much

  Nathan.

  Some people have reported that manually download and install updates succeeded in fact.

  Updates:

  1. http://www.microsoft.com/download/en/details.aspx?displaylang=en&id=27017 (KB2539636)
  2. http://www.microsoft.com/download/en/details.aspx?id=3556 (KB2468871)
  3. http://www.microsoft.com/download/en/details.aspx?id=27014 (KB2533523)

  Make sure you download the one appropriate for your system.

  http://support.Microsoft.com/kb/827218 (ie X 86 32-bit =)

  Install as administrator.