iPhone 5s stuck in a continuous reboot loop

My 5s iPhone has always been great. IOS is underway. My daughter used it yesterday evening at the stream of Pandora, but had finished and he's just sitting there. He started a continuous restart loop. I tried hard reboot (still a few cycles) and I tried to plug it into my laptop to synchronize with iTunes (never, give me the chance to enter my code to access, but iTunes gives me error that I did not enter my access code). I also leave the battery to choke and then restarted, but it's always just. I looked for answers and all seem to focus on the fact that this is happening for iPhones that have been jailbroken, but I has never been jailbroken.

If your iOS device restarts or the unexpected poster - Support Apple Apple logo

Tags: iPhone

Similar Questions

  • Continuous reboot loop

    Help me please, my phone continuous reboot loop. This problem starts at 00:00 hours, I don't know what to do

    Hi miltonjhon,

    Welcome to the community! Since you are new, please make sure that you have checked our Forum.

    Try to remove the SIM card from his cell phone and then restart it, leave the SIM card and see if the problem persists, if it stops then the SIM card is causing the problem.

  • Y700 m2 upgrade - continuous reboot loop cycle?

    Hi all

    I recently bought a Y700 laptop with a 128 GB m2 and 1 TB hard drive.

    I found that the 128 GB drive is just about acceptable, but as I do photography editing, the drive working essentially consumes the rest 30 GB I have free instantly. I would also like a little more room for manoeuvre for failing to manage the storage space so closely.

    So I bought the following:

    Samsung SM951 M.2 PCIe SSD 512 GB
    SM951 Series MZHPV512HDGL-00000
    Capacity - 512 GB

    I read NVMe version is not supported, but I assumed it would work.

    I tried to use Acronis True Image clone/backup the existing drive, actually a recovery disc and used to restore the backup to the new drive. So far, everything seems to work.

    However, after reboot, first of all, I got a BSOD message saying "Inaccessible_boot_device" and then the system reboots. At this point the loop starts, the screen shows the text "LENOVO" on black for about 10 seconds, switches and 2 seconds later goes on to repeat the process to infinity.

    Thinking it was a problem with Acronis, I tried to use the Installation of Windows Media disc for just fresh install windows on the disk. Once again, everything seems to work and has been installed properly. However once the installation has been completed, once again reboot loop began.

    I must add that when the loop runs, hitting F2 or any other key does not work, so I can't access the bios to tell the computer to boot from a key USB etc. To exit the loop, I have to power off the laptop and remove the offending SSD drive and then restart. At this stage F2 works, allow me in the BIOS to re - assign the USB as a boot priority to try to restore media etc.

    I also tried to do "repair Windows startup", but after a few minutes, the repair process said that he could not repair the drive.

    At this point, I wonder which of the following occurs:

    1 drive is defective

    2 - the drive is not compatible (material)

    3. drive is incompatible because of outdated drivers (the laptop is 1 month old)

    Any help you offer is appreciated, because I doubt now, I can return the drive given the way it has been used now!

    An apparent difficulty has been to change the UEFI boot to legacy mode, but I kept the UEFI as first priority in the boot sequence. Things seem to work fine now.

    Weird that the 128 GB m2 player provided by Lenovo was beautiful on UEFI, yet my 512 GB there is no work?

  • Help! HP Envy 100 stuck in endless reset / reboot loop

    My new printer Envy 100 has suddenly been unusable by getting himself stuck in endless reboot / reset loop.

    He started the other day. A message appeared on the touch screen of the printer asking me if I wanted to update the software. As everything works fine to this day, I clicked No. which seemed to he left.

    It restarts, goes through the motions, then as soon as the main home page appears, it turns black again and goes through all of this again and again and again...

    In one of the rare moments where I managed to access the settings before it turns off again, I have established that it * is * running the most up software to date.

    Anyway, I unplugged and back of left unplugged for a few days, and as soon as I plugged the in... He started and cannot be stopped.

    I'm on Mac OS X 10.6.8. No error message appears anywhere, it just gets stuck in this loop reset, without saying why.

    I hope someone can help - I can't use the printer at all.

    Thank you

    Giles

    OK, the solution came in the form of an update of the HP software. As HP offered to replace the item, a new update appeared for most HP printers, and I installed it on the computer. Check on the printer now revealed a new update here as well, so I thought that it is prudent to do both.

    Since then, this problem has disappeared.

    G

  • 0 x 00000024 reboot loop

    I rebooted Vista recently it was very slow, and it got stuck in a continuous reboot loop. Startup Repair also fails to load correctly and restarts until I can do something with it. They showed me a BSOD with an error message after turning off the auto reboot:

    Stop: 0 x 00000024 (0 x 00190444, 0x86ec9940, 0xc0000102, 0x00000000).

    They tell me to run chkdsk, but don't know how while I can't in Vista at all.

    Safe mode is stuck at crcdisk.sys and restarts.

    Any ideas? How can I run chkdsk without going into Windows?

    Thank you

    Hello

    Check the following message methods to check the disc including making a repair disk.
    Some discs of diagnosis of the auto manufacturer to start.

    -----------------------------------------------------------------------------------------------------------------------

    Check this thread for more information using BlueScreenView, MyEventViewer and other methods to solve problems
    BlueScreens - answers top 3 (+ 1 more).

    http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

    ------------------------------------------------------------------------------------------------------------------------

    Alteration of the disc or the material associated with the operation of disk (hard drive, wiring and controller of the motherboard),
    lack of enough system memory, BIOS and antivirus/antispyware/security programs may have a role.

    ------------------------------------------------------------------------------------------------------------------------

    BCCode: 24 0 x 00000024

    Cause

    One possible cause of this bug check is damaged drive. Corruption in the system of NTFS file or defective (sectors) on the hard disk can cause this error. Corrupted drivers SCSI and IDE may also compromise the ability to read and write to the disk system, so causing the error.

    Another possible cause is the depletion of memory pool non paged. If the nonpaged memory is exhausted, this error can shut down the system. However, during the indexing process, if the amount of memory available nonpaged pool is very small, another driver in nonpaged kernel memory in pool mode may also cause this error

    Solve the problem

    To solve a problem of hard drive corruption: Check Event Viewer for error of SCSI and FASTFAT (syslog) messages or Autochk (the application log) that might help determine the device or driver that generated the error. Try disabling any antivirus software or Disk Defragmenter tools that continually monitor the system. You must also run the diagnostics of material provided by the manufacturer of the system. For more information about these procedures, see the manual of your computer. RunChkdsk /f /r to detect and resolve any file system structural corruption. You must reboot the system before the start of the analysis of disk on a system partition.

    To solve a problem of impoverishment of nonpaged memory: Add new physical memory to the computer (which increases the amount of memory available to the kernel nonpaged pool), or reduce the number of files on the volume Macintosh (SFM) Services

    Schedule chkdsk to run at next boot (checkdisk).

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    BCCode: 24 0 x 00000024<-- read="" this="">
    http://www.faultwire.com/solutions-fatal_error/NTFS-file-system-0x00000024-* 1051.html? order = votes

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

  • Laptop stuck in a reboot loop

    Original title: locked cpu

    my computer laptop gateway is in a continuous reboot loop at startup.vista family premium is the operating system, automatic restore or restore to an earlier point in time not working, what a Dick I do?

    Hi Ohmer,

    1 did you recent hardware or changes to the software of the system?

    2. you receive messages or error codes?

    You can try to disable restart of the automactic on the failure of the system and look for the error.

    For more information, you can consult the following article:

    Startup options (including safe mode)

    You can also try the following steps and check if it helps.

    Method 1:

    You can try to perform a test of the last good known Configuration and check if helps solve the problem.

    Using the last good known Configuration

    Method 2:

    You can also check if the problem occurs in safe mode.

    Start your computer in safe mode

    Method 3:

    If the problem occurs in safe mode, and then try to perform a startup repair and check if it helps.

    What are the system recovery options in Windows Vista?

  • Alureon Trojan & reboot loop

    My asus laptop (3 years) a 'alureon trojan', my anti-virus figure it out this morning. But now, my laptop is in a continuous reboot loop and I can not even past. I tried connecting all modes and it restarts just my computer. I don't know if it's the job of the Trojan horse (I am not very well informed on computers) or something else, but if it isn't then I can't even past the BSOD page to fix my Trojan? Can someone please help? I don't need to work I just want the BSOD. I reformat my laptop but I have some very important pictures (sentimental) that are only on my computer.
    Can someone help me please?
    Thank you
    Camille

    You can use the Microsoft Standalone System Sweeper to try to remove the Trojan horse without starting Windows.

    If System Sweeper cannot repair your computer, you will need to use a Linux system on a CD or USB stick to copy your photos from the hard disk before get back you in shape. Post back for more if you need to do.

  • PowerConnect 3448P continuous reboot

    I have two switches to PC3448P.  That I've updated the bios and firmware no problem.  The other, something must have been corrupted during the update process - the switch is stuck in a continuous reboot.  The documentation that came with the latest firmware says:

    If you try to upgrade from 1.0.1.13 or below, please

    version of the software that 2.0.0.34 is downloaded on the PowerConnect switch

    34XX series, as well as the new version of startup code 1.0.1.01. New firmware

    and the new startup code must be updated at the same time. Failed to download

    the new bootcode translates the system to reboot continuously. This

    It will take a XMODEM from the previous version of the software download

    (PowerConnect_34XX - 10113.ros) using XMODEM and the Start Menu for

    recover.

    I need to get a copy of the firmware "PowerConnect_34XX - 10113.ros" file to try to restore this switch to a working state, but I cannot fid anywhere. Can you tell me a download of this file?

    Hello

    Try this link http://downloads.dell.com/network/PC_34XX_v10113_A05_Firmware.zip

  • BlackBerry Torch 9800 Smartphones continuous reboot cycle

    Please can you help me?  My Torch 9800 is stuck in a continuous reboot cycle.  Press and hold the return key does not it in safe mode and my Office Manager does not even recognize the existence of the phone.  Please can someone tell me how can I recover the situation?

    Hello

    Given what you describe, you should probably use these more drastic repair attempts:

    I hope you have a good backup, because in this case it is usually not possible to take one now.

    Good luck!

  • Pavilion dv6636 stuck in a reboot loop with no boot

    Hello

    I have a Pavilion dv6636 purchased on Oct / 2007 which saw a reboot loop with no boot. By pressing the Start button, I can see the hood leds on, power on (as well as the port for illuminated around blue AC adapter), HD led being turned on once and can hear the pilot DVD is powered and the fan turns, then, after about 10 seconds (while the screen is always black), he stops, remains off for 5 sec , then restarts, stuck in this loop. Experiences I've already done:
    -hard reset
    -reset of memory
    -stable memory locations
    -exchanged memories
    -started with memories (sounded a beep as expected)
    -had started with HD (continued with the same symptoms)
    -F8 or F2 keys pressed during startup (black screen and continued with the same symptoms)
    -F10 key during startup (by pressing F10, it does not shut down as usually does, but rest died, with black screen and rotation of the fan)
    -external monitor plugged in when you start (black screen and continued with the same symptoms)

    Same question occurred in about 4 months ago, but at that time, after break of a week I tried to start and has been a success. Not at the moment.

    Please, any thoughts of what could be the problem?

    Thank you

    Hello Emmanuelle,

    sounded pretty good!

    I got and my laptop is working normally after failed BIOS by following the steps you suggested.

    Now, I have updated the BIOS by the F32 (current release) version and is running successfully.

    Very well.  Thanks about.

  • Stucks L50 - A satellite in reboot loop

    My L50 - A Satellite is stuck in a reboot loop. I put the computer off and drained the battery.

    Whenever I have it plug in I see the opening screen Toshiba (with no invitation to press F2 to pass set up) then it goes back to the reboot screen.

    I tried via a recovery bootable on USB but t does not work.

    What is there to do?

    > I tried to use on a USB key bootable recovery but t does not work.

    I assume you tried to reinstall the original recovery image. It should work.

    Enter the BIOS and set it to default settings. After that restart your computer and press F12. Choose the USB device as the boot device and try to restart recovery image installation.

  • Computer is stuck in a reboot loop, while security updats

    ORIGINAL TITLE: reboot problem

    Computer is stuck in a reboot loop, while security updats

    Hello

    1 were there any hardware or software changes made on the computer before this problem?

    2. do you get an error message or an error code? If Yes, what is the exact full error message?

    I would suggest trying the following methods and check if it helps.

    Method 1: Try to run the system in safe mode restore.

    Step 1:
    Try to start the computer in safe mode, here is the link:
    http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

    Step 2:
    Once you start the computer in safe mode, try to perform the system restore and check that if it helps, here is the link:
    http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

    What are the system recovery options in Windows Vista?

    http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

    If you were able to start your computer normally by using the system restore, then refer to the following method, and try to update your windows.

    Method 2: To help resolve the error and other messages, you can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

    Note When you perform a clean boot, you may temporarily lose some functionality. When you start the computer as usual, the function returns. However, you may receive the error message, or you can experience the original behavior.

    Note: follow step 7 to reset the computer to start as usual after the boot process.

    http://support.Microsoft.com/kb/929135

    See the following help link.

    Problems with installing updates

    http://Windows.Microsoft.com/en-us/Windows7/troubleshoot-problems-with-installing-updates

    Hope this information helps.

  • Reference Dell Vista stuck in a reboot loop must restore

    I have a dell desktop computer I bought from rent a Center about 2 years ago. It comes with Windows Vista. They don't did me not a recovery disk. I had a lot of questions and restore points were not helping, so I went through f8 and fact a reset. After that she completed successfully I clicked on finish, and it began to restart, which I expected.

    Now, however, he is stuck in a reboot loop. It gets to the screen that has Dell on this, with the f2, f12 options in the right corner, and then start again again and again. I tried to press f8 and hope go in safe mode and see what was up, but f8 does not open and f2 and f12 are not help at this point. they give me boot priority and so on but no real start until now kind of options. It is possible that windows doesn't have factory loaded, and now I have simply no operating system?  They say they have a reset disk can I come down and use, but im wondering if this will help because I can't really get anywhere or if im just done...

    No messages online that I was looking for really specific my situation...

    * original title - Dell Vista Start Up start up loop *.

    Hello

    ·         Did you follow the steps in this article to restore the computer to factory settings?

    If a factory restore full does not lead to a fully functional version of Windows then you have a hardware problem. I came in contact with Dell technical support.

    Diana

    Microsoft Answers Support Engineer

    Visit our Microsoft answers feedback Forum and let us know what you think.

    If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • HP Windows 7 stuck in a reboot loop

    Hi all

    Recently, I accidentally upgraded my HP Envy 14 from Windows 7 to Windows 10 and let the month pass without switch back.  Due to one host of other problems that have arisen, I decided to Windows 7, so I took out my old Windows 7 recovery disc to re-install Windows 7.

    He successfully reformats the hard drive and everything seems to go well until the end of the installation, when all of a sudden it shuts off and restarts.  He will then get as far as the 'starting windows' screen before it restarts again, each time giving to the screen "Windows is not stopped successfully", is not just a part of the installation process.  He's stuck in this reboot loop.

    Any advice?

    Couple comments:

    I have created a startup repair disk and ran the Startup Repair, but he reported having found no problem.  Very well.

    When you try to start the computer in safe mode, I get to the screen "Windows is set up your computer for first use" and then informs me that Windows cannot complete the installation in safe mode.  He gets up to now in normal mode, however.

    The battery is thus burned - can install Windows on a computer that has failed the test of the battery?  I don't see how there would be a relationship, but I'm really running out of ideas.

    Thanks for any help/insight you have!

    Eventually the recovery disc files are corrupted, try the following:

    Download Windows 7:

    For 5 years, Microsoft made it fairly easy for users of the Windows 7 operating system to get reinstall media. If you have lost your support disc or installation retail collection; either it has been damaged or defective; You can download a copy of the edition that you have licensed from a membership site called Digital River. More recently, Microsoft ended the availability to reinstall media that you can download as a. File ISO in Digital River, which is a digital reproduction of an optical disc.

    It was particularly convenient for people who could not easily get the manufacturer's recovery media, did not want to pay the fees required to get or preferred a clean configuration without the software packaged manufacturers or even a recovery partition does not work. It's easy to use, all you had to do was reinstall and reactivate using the product key located on the certificate of authenticity and download all the drivers on the manufacturers website.

    Given that this option is no longer available, what are your options? See the article for more details:

    How to: What are my options for Windows 7 reinstall media?

    Make sure you scroll down and read the section:

    What to do if you cannot get your manufacturer recovery media, refuse to use or to buy it or the Microsoft Software Recovery Website does not work?

  • Reloading the blackBerry Z10 Z10 software stuck on logo Blackberry, continuous restart loop, did not help...

    Hello

    Here to find the solution for my beloved BlackBerry Z10 STL100-3

    One day, precisely 26 May 2016 my Z10 battery Blackberry went below 5% or something, I rushed to connect it to the charger but before doing so; It is just off. I plugged in the charger for several hours, but it went to reboot mode as he went to the course passed. It just kept flashing empty battery symbol.

    Problem: BlackBerry Z30 stuck in a reboot loop

    Comments/Details:

    1. when it is connected to the wall charger, the red LED flashes for a few seconds, the display shows "BlackBerry" name. After that,.

    a. device either goes to a restart mode, the icon reload Blackberry OS, the charging progress are shown and about 60-70% progresses he new go to the mode (flashing empty charging symbol) load

    b. or device is standing right in the mode, load with screen showing beteer empty, load, seeing to the top flashes still with the typical color of LED for empty-drained/low battery levels.

    2. keep on charging for several hours, or even overnight will not help to restart. And he remains in charge mode with b symptoms of "scenario". Start button / stop fails to start the machine and after several attempts, it flashes only 'Blackberry' on screen and again charge mode.

    3. as soon as the connection to BlackBerry device link gets detected for a few seconds. And the screen displays the name of "Blackberry", "scenario one" described above occurs. And he just repeats.

    4. that the device is detected for a few seconds, being fast enough to select the option "Reload" when Blackberry link shows that it connected returns with the message "software update has encountered an error.

    After meeting thiis reboot loops question on 26 May 2016, I searched rigorously blackbery support forums and other web pages a di a factory reset/software reload on my device. I lost all my data, but did not care as I wanted my Z10 back to life.

    Now its been 2-3 months I see my Z10 stuck in restart loop and hoping that maybe it lights up or I will be able to find the solution.

    Kindly help.

    Hi J Sanders,

    Z10 was connected to the wall charger and all the tips/advice you mentioned have been tried. He could not start device.

    Before trying the ADF, to check if battery is dead or defective; I kept it in my brother Z10. The battery was load and after a while, he turn the unit on its own.

    However, the pile of work of Z10 my brother could not initialize my camera. I guessed corrupted software connection or the battery could be a problem.

    I carefully observed battery connection ports, specifically the part that establishes the conncetion of metal tabs of the battery with the unit (given in the image http://www.gsmzone.co.uk/Blackberry-8900-Z10-Battery-Connector).

    I found one of the metal connector stuck / out partially / fits loosely / spring-movement irregulars / and is not able to communicate perfectly with the metal strips of the battery.

    I tried to solve this problem by manually removing the metal connector. After several test, I managed to do it.

    I put my battery in my Z10, he acknowledged, and red LED flashed, name BlackBerry flashed, Blakberry OS Reload icon flashed-has increased 100%, Blackberry 10 name flashed and Z10 began. Device came to operational status.

    Current operating system version is 10.3.2.2836.

    No SIM or media inserted in it.

    Charge the unit and check if all functions work fine.

Maybe you are looking for

  • locker of 6s... :(

    My daughter has locked and forgotten the password for his 6 sec, it has never been synchronized on iTunes.  Is - fixable?

  • Pavilion 15-p101nr: 15-p101nr usb host driver

    Hello. I deleted hp-version of Windows 8 and installed clear Windows 8.1. I also installed all the drivers for my laptop on your site, but when I tried to plug my card its USB, a PROBLEM that has happened: it reboots once per second. I know this prob

  • How can I reboot an Acer Aspire One / Windows XP Home Edition Version 2002 Service Pack 3 from scratch?

    My Acer Aspire One / Windows XP Home Edition Version 2002 Service Pack 3, (laptop/netbook computer - no disk drive to insert a disk or anything like that,) only has 1 GB of memory/160 GB of storage and is far off in the ORIGINAL manner, he came, I ne

  • The HP BIOS update seems to have caused havoc with my laptop HP G62

    After him have updated software for my PC BIOS of G2-244 HP laptop usb mouse doesn't work.  I checked Device Manager and all the USB ports seem to be defective with a "!" triangle icon next to them.  When I ask to check the drivers of these ports, th

  • Virus, TrustFighter, lock up.

    I was on the home page of Microsoft when viral alerts infiltrated. Trust Fighter seems to be affiliated with MicroSoft. He asked me to register for $39.00 and, of course, now they have all my information. The Fifhter Trust was simply a loop for the s