IPhone 6 s completely black screen

So I bathed recently with my phone by accident, but I jumped in the pool I checked my pockets and realized my phone was there, so it did not take more than 5 seconds before he was out of the water.

After that, I put the rice for 48 hours and allow it to dry completely. I then tried to turn it off, but he showed me the recovery screen (itunes logo and charger), so I plugged into my PC and restored the phone after a little fight with a few error messages. Essentially the device got restored and it turned on and worked perfectly fine - or so it seemed. After a while I turned it off the to cool as it was quite hot. After about half an hour I tried to start back upward and it came to the unlock screen and I entered the password and the Sim card code, but once I tried to unlock the sim card it freezes at the «unlock...» ", and then the unit turns off.

Now, the screen is completely black and unresponsive. I tried to do a reboot with the button home + power, also put it in DFU mode and restored several times (I can restore the iphone despite the screen is black because itunes recognizes the device). All I hear is the sound that comes when you connect and disconnect the device from your computer. Another thing to note is that, while the Treaty restored it disconnected and connected several times, but at times very practical so I think it's supposed to make this (same locations in the process) every time

Maybe it's a screen dead, but I'm on vacation now for another 2 weeks so I can't send to repairation at the moment, and I would really like to have a phone for other weeks here.

And also the unit is hot, even if I have it plugged into a long time ago (30 min) which leads me to think he's working on something.

Thanks in advance

Advertisement

Contact Apple support (mail service may be available) or make a Genius Bar reservation to establish your available service options, which may include services off-warranty / replacement:

Tags: iPhone

Similar Questions

  • iPhone 6 more hot black screen

    TThe screen went completely black with a full charge. The button was almost too hot to the touch. Wouldn't not attached commuter. Is this a recall problem?

    Hi BELCOW!

    I can understand needing my iPhone working correctly at any time myself! You may want to try these steps here: If your iPhone does not illuminate.  Now, if the iPhone has just a black screen and you hear yet or do not have these steps in the article, it would be preferable to contact Apple directly by clicking this link: contact Apple support

    See you soon!

  • I downloaded the trial of the creative cloud vision. But why does the application display a completely black screen?

    I downloaded the trial of the creative cloud vision. But why does the application display a completely black screen?

    I can open the CC but I don't see anything in it.

    I downloaded and months before photoshop. I still see something at the window right there.

    But now, I see the dark window. So I couldn't download the Adobe Illustrator.

    Please help.

    Hello

    Please see the thread below where this issue was discussed:

    Re: screen creative black cloud

    Kind regards

    Sheena

  • my iphone 4S hanged and black screen

    I used the iPhone 4 (factory unlocked) for over a year now with only minor problems. Like a regular day, I was typing a message to my friend, but suddenly he hung then black screen follows... It was a shock suddenly! . I just put the phone to rest for a while and after about an hour, have crossed my fingers and tried again the Home button, but the black screen continued. If the backlight of the iPhone works I can say that, because I see the phone luminates but the "Slide to unlock" is cannot be seen. Since I have been using the phone for a while, I know the accurate position to "Slide to unlock" so if I slip my finger unlocks it too with the default 'Unlock (click) noise' but again once the icons of the apps is not visible, all I see is a grid and fadely. I get the SMS and calls even though I can't read nor I can see who's calling. Because the screen is blank, I can't use the phone but the phone seems to work.

    Try a hard reset by pressing Power and "home" set button until the Apple logo appears. If it is not resolved, try a restore of the phone via ITunes.

  • Computer won't turn on completely (black screen with blinking cursor) after installing windows updates

    8/7, the following updates have been installed correctly:

    Microsoft .NET Framework 3.5 Service Pack 1 and the .NET Framework 3.5 Family Update (KB951847) x 86

    Update definition for Windows Defender - KB915597 (definition 1.63.1021.0)

    Following this installation, the display resolution has been reset to be very low.  When you try to reset the resolution, I was alerted to a driver problem, so tried installing this in vain (below error code)

    Intel Corporation - display - Intel (r) G33/G31 Express Chipset Family

    Error details: Code 800703E3

    After that, he went to sleep the computer, but was unable to select 'sleep' (it is grayed out) but the stop keys option indicates that the updates were ready to install so I stop thinking which may help.  It was last night.  This morning, the computer was on, seen the screen DELL, then a black screen with flashing white cursor in the upper left corner.  I tried ctrl-alt-del, got the dell screen appears again, then black screen.  I tried ctrl-alt-del, thinking I could try one of the options key F at this time, but he won't even go to this point, the dell blank screen just screen.

    Any ideas would be very appreciated!  It is the second major problem that I had recently after updates vista install (the last time I temporarily lost access to all my files, because they were placed under a temporary user account that had been created!)

    Thank you!

    Hello

    You try to borrow the Vista DVD to any of your friends and do a repair (inplace upgrade) it might help you solve the problem.

    All the best,

    Geek

  • S205 completely black screen

    Hi, after changing the priority of the boot in the bios, I tried to boot from a USB but the screen is just black.

    The lenovo logo does not appear and is not light on substantive. I also tried to connect a display external, but without success.

    Unfortunately, I wasn't able to solve this problem. I send back to the online store, that I bought, and they send me a completely new machine. I tested the ram however, and it was OK. Guess it was a motherboard problem. My new S205 works fine now. Good luck with your

  • 6 s iPhone restarts with black screen randomly. However, the system always restores the same question.

    I have an Iphone 6 s 128GB. The iphone automatically restarts with black screen and there is no particular application I use when it crashes.

    I did a system restore twice but still the same issue. Could someone please help?

    If the restore does not solve the problem, it is high time to take your device at the Apple Store for more diagnoostics. This may be material / display problem. Good luck.

  • iPhone 6 alternating between the black screen and the Apple logo and nothing else

    my iPhone 6 alternates between a black screen and the Apple logo, what do I do?

    Hi Nathanielfromwa,

    If your iPhone 6 alternates between black screens and the Apple logo, this could be a problem that can be fixed by wiping your iPhone to factory settings. If this is the case, save your iPhone first. I've included links if you need help with backing up your iPhone, but also to reset to the factory settings.

    How to back up your device using iCloud or iTunes - Apple Support

    Erase content and settings on your iPhone, iPad, iPod touch or Apple Watch - Apple Support

    I hope this helps, and if you have more questions, do not hesitate to ask!

  • Starting on black screen (VFD002)

    My MacBook Pro (13-inch, late 2013, OS X 10.11.6, retina, Iris 1536 MB Intel graphics card) has the same symptoms covered by the repair Extension program which deals with the graphic problems:

    https://www.Apple.com/support/MacBookPro-videoissues/

    However, nothing is said about 13 '' models, which is my case. Why?

    Start up my laptop to a completely black screen. I ran the diagnostic test and it seems that there is a problem with the graphics card: VFD002

    It appeared after I closed the lid of my Macbook, sleep in battery mode implementation. When I opened the lid of my MBP display did not wake up from slumber. However, I can use an external monitor via HDMI, but if in SafeMode only (the retina display main black stills and the external screen is flickering when scrolling). In addition, this graphics card problem leads to crash the system.

    I already tried Resetting PRAM and SMS, but in vain.

    It my second time this has happened. The previous one-any return to normal until after a new OS install. But it happened again so reinstall OS X is not a solution.

    More and more users are complaining of the decline in the quality of some hardware components...

    However, nothing is said about 13 '' models, which is my case. Why?

    The reason is that they are not included in the repair Extension program. Follow the options in the process of repair anyway.

  • HP Touchsmart 310 1100 HP Screen-No Black logo or whatever it is-just a black screen

    Hi-

    I have a HP Touchsmart 310 1100 which when I turn there is only a black screen and I can hear the fans running. No HP logo or guest to enter the bios, just a completely black screen.

    I tried:

    (1) HP suggested resetting the default bios (http://support.hp.com/us-en/document/c02217843) settings by pressing f10, f5 etc.

    (2) remove the hard drive, reinstalling memory, unplug all usb accessories

    (3) used another power supply from an another 310 HP

    (4) change the jumper on the motherboard from 1-2 to 7-8 and back to 1-2 to clear the cmos memory

    I'm about to remove the cooling fan and the unit and re-insert the processor, but I wonder if there is something to try before that.

    I'm starting to think it's a bad mother, gpu, or display the power inverter.

    It is out of warranty, so if anyone has any advice I would be happy.

    This seems to be a problem that has been listed in a dozen other posts without real solution given.

    I solved my problem with my 310 - it was the CPU. Replaced with the same model cpu AMD bought on Amazon.

    Works fine now.

    There is no video card to replace on my model 310. There is a video chip that is soldered to the motherboard.

  • Satellite A200 - black screen with two beeps

    Date: October 17, 2009

    I have Toshiba Satellite laptop computer * model A200 PSAFCA-01400J *. I am facing a problem of * completely black screen * (I can't see any image either). It happened twice more than the screen wouldn't turn on by moving the mouse or the touchpad. To turn on the screen I had to restart the computer. The screen worked well until it turns off again. Since it does not turn on even after I restarted my computer several times. I noticed that my * Windows vista home premium * load properly I can hear audio that indicates that I am ready to open a session. I also noticed the sound signal after slipping my finger on the sensor attesting that I connected successfully, but the screen remains black.

    When I turn on my computer, I noticed that it sounds two beeps, first beep is short and the second beep is relatively long. I tested the cover closing the cover switch and noticed that my computer goes into sleep mode and by opening the cover that Eve turns off and my computer turns on again; but the screen remains black. One of my friends suggested that the backlight of the screen inverter or the lid switch is defective. Can someone tell me what could be the problem and what do the two beep codes?

    Thank you

    Hi mate,

    Normally the beep codes at the start of average that it s something wrong with the hardware of your laptop. As Akuma said, maybe the graphics card or RAM must be replaced or other parts too.

    Have you already tried to connect an external monitor? You can see a picture on this subject?
    I don't know but maybe what he s m only internal something wrong with the monitor.

    In any case, I think you should contact a service provider for help. Technicians can check the laptop and fix it for you.

    Welcome them

  • HP Touchsmart IQ770 Desktop, black screen

    Need help please, old 18 months IQ770, I turned on this morning and have a completely black screen. Blue indicator light is here and will fan but nothing else. There is a beep when I touch the screen, but nothing works. Anyone out there who can help me.

    Want to thank you millions.

    I did exactly as said and boy these all-in-one... I swear that every engineer has designed this crap should get shot.

    AAAAnyway brought back my gfs Touchsmart IQ775 back to life thanks to your advice.

    Took the $% # ^ tried reflow it, video card... eventually burn LOL.

    Changed the cable microphone vga LVDS # 1 to LVDS #2... and Bravo.

    I was able to install windows 8.1 then and now everything seems to work perfectly until now.

    Thanks comrade. Its been years that I've been in these forums, because I stopped using HP for this reason along with their products and the horrible customer service. Just to let you know.

    Peace out!

  • Vista starts and has a black screen with a white pointer, what should I do?

    I have a toshiba satellite laptop computer with vista.  It seems to boot into an operating system, but I don't see a white mouse with a completely black screen pointer.  Is it a problem of theme, and in this case how to fix?

    Hello

    Try following the methods provided below and see if it helps:

    Method 1:

    Try logging in safe mode and check if you are facing the similar question:

    http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

    If you are able to boot into safe mode, you can try a clean boot

    How to troubleshoot a problem by performing a clean boot in Windows
    http://support.Microsoft.com/kb/929135

     

    Note: Don't forget to reset the computer to start as usual when you have found the culprit. Follow step 7 on top of the kb article.

    Method 2:

    I would say that you want to run System Restore in windows recovery mode and check if it helps. See the link below:

    http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

    Method 3:

    I suggest to update the graphics drivers on the manufacturer's Web site, click on the link below:

    http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

    Also, try to restart the computer by pressing F8 and in the advanced startup options, select Enable VGA Mode and check.

    Disconnect external devices and check

    Hope this helps,

  • Windows starts, but does not charge not (black screen with cursor)

    [Sorry for the long post, but I feel the need to explain my situation]

    I have the following problem:

    I turn on my PC, and Windows shows it is normal loading screen, then it goes in a completely black screen, with just the mouse in the middle. By the size of the cursor, I can say that it is in a low resolution, probably 800 x 600 (compared to my usual 1920 x 1080). I am able to movements of the mouse, but with no particular purpose without something to click on. No other keyboard input seems to work, except for press SHIFT 5 times, which shows the keys dialog box to self-retaining (with just 'yes' or 'No' options, no other connection); and Windows key + U, which shows the ease of access Center. CTR + Alt + Del does NOT work.

    So far, that's what I tried (in chronological order):

    1. Start in Safe Mode, Safe Mode with network, safe mode with command prompt Mode, start low resolution video, last known good configuration: all give the same result as to start normally.
    2. Repair of your computer:
      1. Startup Repair: find the registry errors (I realized and fixed this more later on)
      2. System Restore: did not find any previous restore points (I know with certainty that there is, I took the habit of making regular restore points).
      3. Windows memory diagnostic: not found error.
      4. Command prompt:
        1. Ran the command chkdsk /f r, has no error report.
        2. Ran sfc/scannow: I don't remember the exact report, but he asked to restart the computer to complete the repair of the problems. I rebooted and ran the new order for the same result.
        3. Forced the scan with: sfc/scannow damaged = c: \ /offwindir = c:\windows, concluded and repair errors, not always not load windows.
    3. Ran Dell Diagnostics start, found no errors.
    4. Startup Repair ran found once again the registry errors. I found the solution to this in a forum for Microsoft Help ( answers.microsoft.com/.../f77d5355-b8be-41d6-af24-cae994e1768f ) and fixed the problem. I rebooted, but the problem persists.
    5. Startup Repair does not detect now no error. I tried restoring the system again, we find 2 restore points dated AFTER the beginning of my problem. I decided to restore it in any case, but none of them worked.
    6. I ran Windows Defender in offline mode:
      1. Quick scan: and found 2 threats and remove.
      2. Full system scan: found 4 more threats, removed 2 of them, the other two could not be removed because they were in an ISO file.
    7. I've tried steps 1, 2 and 3 with no luck.

    With every step, I am aware that I am closer to having to reinstall Windows, then I decided to see if I could still access my HD to save my personal files. I did a live Linux CD (with Ubuntu), but I have a problem of mounting the readers, because they are in a RAID0 configuration. "sudo dmraid s" gives the following error: "ERROR: Sie: number of devices in RAID wrong value"isw_dbdffjficc_ARRAY0"[1/2] on/dev/sdb.

    Important details:

    I changed my graphics about 4 months ago (a 750ti of Nvidia GTX for an ATI Radeon HD 6450), and told me that I can run short with the power supply. The new card requires a minimum of 450W, and I think that my diet is 460W. This may or may not have something to do with this question, I have no idea.

    My 2 hard drives of 500 GB RAID0 configuration has brought me a lot of problems of the day 1. One of the HARD drive would be randomly (I am able to hear a clicking sound different when this happens) failure and the computer would break. At the start, he would ask a boot device. The Dell boot utility would then recognize only 1 readers, but would end without errors. After a reboot or two, everything would be fine and would be boot windows normally (apart from the usual error recovery screen) with no sign of corrupted data or anything. As I said, it happened are the arrival of my PC, but restarting a couple of times still attached. From now on, the two HD seems to work very well, the Dell utility recognizes two of them and found no errors in one of them, and I can access any directory from the command prompt.

    Is there anything else I should try before reinstalling Windows?

    Before the installation, I really wish I could recover my files (I have important documents of the College), is it possible to do this?

    Sorry again for the very long post (and for any errors of language, English is not my native language) and thanks in advance.

    Since you have not yet had your data readers. I recommend a Windows installation without formatting the drive... I don't like this solution, but at this point, you have probably tried everything.

    Use a reinstallation of Windows 7 installation DVD, make sure that you select...

    Select custom: Install Windows only (Advanced)

    If you do not select one of the route options and everything simply highlight the largest partition and click Next:

    Windows will dump all the old Setup files into the Windows.old folder

  • Dell Optiplex 3020 - the black screen after dell logo (happened after windows updates froze at halfway and systems were restarted)

    We had windows updates run on all our systems of windows 7 in our medical center.  13 or so of our 3020 s Optiplex froze for eight hours about in a State of "install updates 1 of 24".  I have all them turned off and restarted units.  Once units have been restarted, they gave the Security windows startup or start-up option normally.  Those who had selected the option to 'start normally' would display the logo dell at startup, then click on a completely black screen (all devices still in market and monitors recording an active signal even if no picture).   Those started in safe mode w/o networking, loaded in safe mode.  I rebooted the machine in safe mode, and they all started out in windows without problem.

    For systems that go completely black after the dell logo.  I am able to F2 in the BIOS, I can run diagnostics from BIOS and I can't F12 in boot options, but I cannot F8 or SHIFT + F8 mode without failure or fact start in safe mode, please come under early start options.

    Anyone happen to know a way to launch a system of 3020 optiplex in safe mode without the use of F8, SHIFT + F8, go through msconfig or remote access to the registry (because I can not remote in the system on the network)?

    Maybe I can put the hard drive in a dock and change the registry in this way?  But can I change the potentiometer to force secure boot? or is it not possible to make a bcdedit to it as an external drive, install it in his camera and force it to safe boot the next time, he is running?

    Any ideas or suggestions would be very appreciated.

    Hello

    Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

    I suggest you to send your request in the TechNet forums to get the problem resolved.

    Please visit the link below to send your query in the TechNet forums:

    https://social.technet.Microsoft.com/forums/en-us/home?category=w7itpro

    Hope this information is useful. Please come back to write to us if you need more help, we will be happy to help you.

Maybe you are looking for