iPhone save personalized answering machine message

Similar Questions

• HP Officejet Pro 8620: after that I set up my fax, cannot answer phone or answering machine messages

  I recently set up my fax feature and now I cannot answer my phone and cannot get messages on my answering machine.  I'd be ok just to cancel the fax feature that I use really, but do not know how to do this.

  I really need to get messages more faxes.  Any help is greatly appreciated!

  Charles, thanks again for your help.  I have reset my answering machine and now everything works!

  I am so happy!!

  Thanks again

• BlackBerry Smartphones answering machine Messages Inbox

  Message box to 3 voice messages only. How can I increase this number?

  Thank you

  Hi and welcome to the Forums!

  By 'Box of Message', if you a reference to the registration system that contains messages of real voices, which is controlled by your carrier... you would have to talk to them about this limit.

  Good luck!

• HP Officejet Pro 6830: Receive faxes with a HP officejet pro 6830 w / answering machine

  I had an OLD officejet model that could receive faxes even if the answering machine was not connected directly to the fax machine the 6830 manual says that it must be directly connected.  My current Brother printer does NOT receive faxes because of this problem.  Anyone know if I directly connect my machine to this model (Officejet 6830) to make it work?  I won't buy it if it will not work.

  Hello @JPJ408,

  Welcome to the Forums of HP Support!

  I understand that you are looking to buy a printer all-in-one HP Officejet Pro 6830 for fax purposes. While the User Guide advise you to plug the answering machine directly on the back of the Officejet unit, it is not necessary.

  If you have a fax with an answering machine on her line, the only requirement is that the fax is set to two rings higher than the answering machine. Most of the responders are put back on 4 rings. As a result, you would set your Officejet to automatically pick up on 6 rings. In this way, when a voice is heard, you can manually respond to the call before the answering machine to pick up. If you are not home and then people can still leave messages on your answering machine. If you have a fax to come through, do not respond. The answering machine will pick up after 4 rings. At this point the fax machine "listen" on answering machine message and if fax tones are detected, the fax will take over and receive the fax.

  I hope this helps clear up any confusion.

• 6500 will not Fax receive when the answering machine is added

  6500 does not receive faxes when answering machine added to the configuration.  So just HP connected to the Jack, I am able to send and receive.  When I add phone & answering machine, I can only send faxes.  The incoming faxes reached answering machine message entering and are not picked up by HP and no dial tone fax haven't saved on the answering machine.   Sounds just the icon disappears in answering machine picks up.  I'm testing with HP test # (1-888-473-2963).

  I have a phone line with 2 numbers associated with it - one for voice, one for the fax with a distinctive ring (triple).  Answering machine is programmed to answer = 4 lights, HP is set to auto-answer = Yes, will answer after 6 rings, distinctive ring triple =, error correction = stop, fax = slow speed, header information, set # with associated distinctive ring, not the voice #.

  Help!

  PROBLEM SOLVED!  Used a combination of silence at end of answering machine outgoing message and "recording" of the distinctive ring on HP device during setup of taxes.  THX so much!

• When answer us e-mail, punctuation change another channel of the alphabet, when the other person receives the message.

  When answer us e-mail, punctuation change another channel of the alphabet, when the other person receives the message.

  When they reply to the message, foreign brands are repeated to us. I find no access in the program to fix this problem.

  original title: problem with punctuation

  Guessing that you use Windows Live Mail 2011, take a look at this page: Why do I see strange characters in messages? It can explain your situation and offer solutions.

  Noel

• problem of answering machine after update from z3 to lollipop

  I've updated my double z3 to 5 android, but now I can not save the message for answering machine and said unfortunately, phone has collapsed. If one facing problem like me? Can someone help me to solve it.

  Try the settings-applications-all-phone, force stop and erase the data. Turn it back on.

• Can send but cannot receive faxes on HP Laserjet on Mac 10.9 Mavericks with answering machine TAM

  I have an iMac running OS 10.9 (Mavericks) and a machine to print/scan/fax all-in-one HP Laserjet Professional M1212nf MFP connected by USB.  I have a phone with answering machine connected system.

  I can send faxes of the HP and the Mac (using the pdf fax).  What I can't do, is to receive faxes on the HP (I know that the Mac cannot receive faxes with this machine).  I tried all the combinations of parameters without result even unplug the phone/answering machine without result.

  Any ideas what I need the settings?

  Hi ChuckStewart,

  It is definitely a head scratcher! I found some additional information from the following link, you use a product of Fax HP with a telephone answering machine (TAM).

  I found this interesting presentation text, when recording the outgoing message on your TAM, share of voice must be at least 10 seconds of time, but not more than 20 seconds . Save 5-7 seconds of silence at the end of the vocal part of your outgoing message (message coming out would be your voice message length plus the extra 5 to 7 seconds of recorded silence ).

   

  I wonder if you might find something useful in the document.
  

  Please let me know. Thank you.

• Answering machine is picking up beeps fax

  Have you tried everything and my Officejet 6500 has when I receive a fax my answering machine kicks on the 3rd ring and the fax is set for 4 lights, yet the answering machine picks up the incoming fax or beeps.

  Hello

  To do this in the right direction, the following needs to be done.

  When you save the message out (GMO) on your telephone answering machine, leave a short pause before speaking. Make sure that your message is clear and understood between 10 and 20 seconds long, containing a silence of 5-7 seconds at the end check the manual of the manufacturer for specific instructions concerning the registration and re-registration of the messages. Set the answer rings on your HP all-in-one product to a number that is at least two higher than the telephone answering machine setting. For example, if the telephone answering machine is set to answer after four rings, product HP must be on answer on six rings. See your HP Product Guide to learn how to change the parameters of fax for more details.

• problems with SPA112 and answering machine

  Recently installed a SPA112 unit, which until this works fine without any problems, but have a few minor issues. Among others, I can't the 2 sec machine records messages; When there is an incoming call the answering machine picks up the call of the appellant Gets a busy; which means that the appellant is not able to hear the outgoing message, nor able to save?

  Worth mentioning that I have before that used a vDSL Thomson 78 modem x who offered two pots the same equitment I use was connected to and also the autoresponder has worked with. Then nothng has changed with the Setup program expect that the SPA112 has replaced the modem ADSL Thomson when it comes to managing the voip part.

  One suggestion I've seen is to change the 'delay to reorganize' at 15, which until now did not make a difference. In addition, the waveform of the ring has the sine value and the default value of the voltage.

  Open to suggestion to point me in the right direction what to look for in the config for the SPA112.

  Format text in time with no seconds and encoding UCS-16 can be ignored. But the messages are truncated at the first ',' and the rest is missing. Second file is the SQLite database...

  You are to test my ability do identify and treat the data hidden, isn't she?

  Well, I decided to extract the lines of SQLite database as TXT form is incomplete. I don't know any format if column Tm, fortunately, we have no absolute time and I wish I have guessed correct relative time in seconds.

  So result (inline comments):

  Incoming calls:

  002.13 > CC_eventProc(), the event: CC_EV_SIG_CALL_ARRIVED (0 x 31), cover: 0, rating: 0, par2: 0 x 40956900
  002.16 > NEW_CALL_STATE(), dial 0: former State = CC_CST_IDLE, new State CC_CST_RINGING
  002.16: CID:CID_initGen() [0] > won 0 delay 1200 phone abcdefg786 name 46bcdefg786
  002.23: CID:OnHookTx PolRev

  Transmission of Caller ID:

  002.33 > uchSendDTMF(), sending 12 DTMF to line 0
  002.33: [0] beginning of the DTMF/FSK CID, CID_ST_ACTIVE
  002.48 > uchSendDTMF(), sending of DTMF a on line 0
  002.64 > uchSendDTMF(), sending of DTMF b on line 0
  002.80 > uchSendDTMF(), sending of DTMF c line 0
  002.96 > uchSendDTMF(), sending of DTMF d to line 0
  003.13 > uchSendDTMF(), sending e DTMF on line 0
  003.29 > uchSendDTMF(), sending of DTMF f at line 0
  003.45 > uchSendDTMF(), sending of DTMF g on line 0
  003.61 > uchSendDTMF(), sending 7 DTMF to line 0
  003.77 > uchSendDTMF(), sending of DTMF 8 to line 0
  003.93 > uchSendDTMF(), sending 6 DTMF to line 0
  004.08 > uchSendDTMF(), sending of DTMF 14 on line 0
  004.25: [0] CID CID: FACT

  Six rings:

  004.52: CID:Ring now
  004.54 > SLIC_startRing State 0 ts 0x1aa4ccon 1000 off 5000 len 60000
  004.54 > pol [0] of the event on the cad of ring 0 0
  009.33 > pol [0] of the event on the cad of ring 0 0
  014.12 > pol [0] of the event on the cad of ring 0 0
  018.92 > pol [0] of the event on the cad of ring 0 0
  023.73 > pol [0] of the event on the cad of ring 0 0
  028.52 > pol [0] of the event on the cad of ring 0 0

  Hook:

  029,50 > off hook [0]
  029.51 > NEW_CALL_STATE(), dial 0: former State = CC_CST_RINGING, new State CC_CST_ANSWERING

  Fully connected call:

  029.57 > NEW_CALL_STATE(), dial 0: former State = CC_CST_ANSWERING, new State CC_CST_CONNECTED

  Disconnected from the remote side:

  039.62 > SIP_sessDlgEventProc: event: 45 (SIP_EV_DLG_BYED), ucState: 3
  039.62 > NEW_CALL_STATE(), dial 0: former State = CC_CST_CONNECTED, new State CC_CST_INVALID

  The CPC sent to the device called:

  047.64 > CPC SLIC_SET_OPEN_STATE on line 0
  048.05 > CPC go to line 0 in CC_CST_IDLE
  048.05 > NEW_CALL_STATE(), dial 0: former State = CC_CST_INVALID, new State CC_CST_IDLE

  Called device still picked up, assuming that the new (outgoing) call:

  048.07 > cepIdleProc (lid = 0, call = 0x17a974, event = 9 (CC_EV_USR_SEIZURE), by = 0, par2 = (Nile))
  048.07 > NEW_CALL_STATE(), dial 0: former State = CC_CST_IDLE, new State CC_CST_DIALING

  Called device hung up the phone, call the cleaning:
  048.72 > hook on [0]
  048.73 > NEW_CALL_STATE(), dial 0: former State = CC_CST_DIALING, new State CC_CST_IDLE

  Camera won, outgoing call starts, digit collection:

  060.05 > [0] off Hook
  060.06 > cepIdleProc (lid = 0, call = 0x17a974, event = 9 (CC_EV_USR_SEIZURE), by = 0, par2 = (Nile))
  060.07 > NEW_CALL_STATE(), dial 0: former State = CC_CST_IDLE, new State CC_CST_DIALING
  065.20 > SIP_sessDlgEventProc: event: 41 (SIP_EV_DLG_TERM), ucState: 4

  Device on the hook even once, no figures were received in this cycle:

  066.01 > hook on [0]
  066.01 > NEW_CALL_STATE(), dial 0: former State = CC_CST_DIALING, new State CC_CST_IDLE

  Camera won, outgoing call starts, digit collection:

  079.17 > [0] off Hook
  079.19 > NEW_CALL_STATE(), dial 0: former State = CC_CST_IDLE, new State CC_CST_DIALING
  081.68 > line: 0 figure DTMFON event has received a
  081.81 > line: 0 DTMFON received the event figure b
  081.94 > line: 0 DTMFON received the event number c
  082.07 > line: 0 DTMFON received the event sales
  082.20 > line: 0 DTMFON received the event e figure
  082.36 > line: 0 DTMFON received the event number f
  082.49 > line: 0 DTMFON received the event figure g
  082.62 > line: 0 sales event received DTMFON 7
  082.76 > line: 0 sales event received DTMFON 8
  082.89 > line: 0 sales event received DTMFON 6
  090.96 > cepDialingProc(), the event = 33 (CC_EV_TMR_DIALPLAN)

  Figures gathered (numbering commited by dial plan timeout):

  090.96 > NEW_CALL_STATE(), dial 0: former State = CC_CST_DIALING, new State CC_CST_CALLING
  090.97: call:[email protected] / * /: 0, rc = 0
  091.47 > NEW_CALL_STATE(), dial 0: former State = CC_CST_CALLING, new State CC_CST_PROCEEDING

  REGISTRY procedure was shot and completed during call setup:

  097.66 > RegOK [0]. NextReg in 296 (1)

  Fully connected call:

  099.05 > NEW_CALL_STATE(), dial 0: former State = CC_CST_PROCEEDING, new State CC_CST_CONNECTED

  Disconnected from the remote side:

  103.75 > SIP_sessDlgEventProc: event: 45 (SIP_EV_DLG_BYED), ucState: 3
  103.76 > NEW_CALL_STATE(), dial 0: former State = CC_CST_CONNECTED, new State CC_CST_INVALID

  The CPC sent to the peripheral component:

  103.76 > statr CPC CC_EV_TMR_INVALID timer
  111,76 > CPC SLIC_SET_OPEN_STATE on line 0
  112.19 > CPC go to line 0 in CC_CST_IDLE
  112.19 > NEW_CALL_STATE(), dial 0: former State = CC_CST_INVALID, new State CC_CST_IDLE

  The device still picked up, assuming that the new (outgoing) call:

  112,22 > NEW_CALL_STATE(), dial 0: former State = CC_CST_IDLE, new State CC_CST_DIALING
  Flash hook events occurred. Dial 0 (data collectors) cancelled. New call (1)
  created, collection figures:

  112,37 > flash hook [0]
  112,37 > CC_eventProc(), the event: CC_EV_USR_HOOKFLASH (0x3), cover: 0, rating: 0, par2: (none)
  112,37 > NEW_CALL_STATE(), dial 0: former State = CC_CST_DIALING, new State CC_CST_IDLE
  112.43 > NEW_CALL_STATE(), call 1: former State = CC_CST_IDLE, new State CC_CST_DIALING

  No number with shot composition timeout:

  136.34 > NEW_CALL_STATE(), call 1: former State = CC_CST_DIALING, new State CC_CST_INVALID

  Line is still the hook at the end of the journal.

  Well. So we have commented on the newspaper. Now - what is your question?

  Note that the CPC Signal (control Signal party call) is a momentary drop in voltage (0 volts DC) on the line for a period of time. It is the way in which the side 'server' of analog line (SPA112 here) informs device calling (your machine here) that the call has been disconnected by side called. Cisco is also using the CPCS to report the same he remote disconnect the case of incoming calls despite CPC does not has been provided for this direction of call.

  Not all phones can recognize the signal of the CPC, especially when called. SPA112 must be configured according to the particular phone's capabilities.

• My MacBook is not connect to my Time Capsule to back up.  IMac my wife backup fine and our wifi works, but when I try to save, I get a message telling me to connect to the T. C. when it is available, which is never.  Help

  My MacBook Pro is not connect to my Time Capsule so it backs up.  IMac my wife backup fine and our wifi works, but when I try to save, I get a message telling me to connect to the T. C. when it is available, which is never.

  The problem started when I upgraded to Yosemite, sometimes back.  I am running 10.10.5.

  The MacBook Pro...

  Click the 'clock' Time machine at the top of the screen of the Mac

  Click Open Time Machine Preferences

  Click Add or remove from your drive

  Under the heading of backup disks, click on the drive it to highlight (probably named 'Data', unless you have changed the name of the drive)

  Click remove disk

  Close the windows

  Restart the MacBook Pro

  Click the 'clock' Time machine at the top of the screen of the Mac

  Click Open Time Machine Preferences

  Click select drive or Add or remove disks

  Choose the Time Capsule drive (probably named 'Data') by highlighting

  Click use the disk

  Close the windows

  Wait a while to see if a backup is performed

  If you want to manually run the backup, click on the Time Machine clock icon, and then click Backup now

  Report on your results. If the backup still does not work, we need the exact message that you see there.

• HP Laserjet Pro 200 Color MFP FAX answering machine vs M276nw

  We have the following MFP: HP Laserjet Pro 200 Color MFP M276nw

  Our office has a phone line to be shared between the phone and FAX (M276nw). The phone is a phone single line of integrated with a digital answering machine Panasonic KX-TG7531 model. I can't seem to find the right combination of settings for ringtone for the phone and the FAX that allows callers to leave a voicemail without the FAX modem tones interfere when the caller leaves a voice message. It's as if the fax does not recognize that the answering machine picked up and he continues to make sounds of modem. The tones are saved as well as the message of the caller's voice, which makes the message difficult to understand. In most cases, the caller simply hangs up without leaving a message (we've heard talk about this later).

  Please tell us how to implement. Thank you!

  Furthermore, the HP Laserjet Pro 200 Color MFP M276nw replaced a MFP from brother, but the Brother FAX has worked with the same phone from Panasonic.

  Hi crmarrio

  I understand that you are having problems of fax.

  Run this test for the fax.
  In the home screen, press the button on the key.
  Tap the service button.
  Tap the fax service.
  Touch run fax test.

  Check all these fax settings.

  Here is a url for the fax troubleshooting.

  http://support.HP.com/us-en/document/c03363598

  Go to the icon/fax setup menu/Advanced Configuration key / private receive/disable it.
  Go to thewrench icon/service/fax service/error correction/stop.

  Go to Settings icon/fax thewrench / fax/advanced/change configuration to speed it to the middle.

  Go to the key icon/fax installation base/menu Configuration/response/game of rings rings.

  (if using an answering machine-more rings on fax and answering machine or rings of mail without a voice for the fax, but receives no voicemail, should get installation of distinctive ring on the line in this case)

  Go to the key icon/fax setup basic menu setup/response/selection of auto mode.

  Go for a key icon/service menu/fax service/clear saved faxes

  Go to key icon/fax installation base/menu setup/distinctive ring/set for proper ringtone type. (if you don't have a special ringtone set on all ringtones.

  Update the firmware of the printer by usb connection.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&docName=c03363598&LC=en&product=5097654&

  Let me know the results of the fax test, and if you were able to send or receive a fax.

  If you're still having problems, let me know and I send you private message how to reset the printer.

• You want to have an answering machine and Fax machine all work?

  Many times people have trouble with reception of faxes while responding to the stand at the same time.

  I have a resolution for you with this problem.

  Check your strings and make sure that everything is connected properly.

  1. on the back of the printer, LINE 1 should go directly into the WALL SOCKET. (If you have a modem, with the phone line tied up in. Plug it into the LINE 1 of this modem.

  2 LINE 2 at the rear of the printer will be obtained directly on the answering machine. (Most phones have an answering machine in one. You can find some separate answering of phone). You always connect LINE 2 on the printer on the answering machine.

  So if you have any problems between the two, there are ways around it so that you can receive faxes, phone calls and messages at the same time.

  I hope this helps out.

• 6500 AIO w / answering machine - ECHO on msgs

  I installed my 6500 wireless all-in-One according to the instructions and a Panasonic answering machine downstream from the printer; It's the same configuration that had with my 6110. For unknown reasons, the recorded answering machine caller message looks like the appellant speaks of a deep well - is now, this feedback? The sound quality with the 6110 in the system was good, but the sound quality with the 6500 is horrible!

  The Panasonic talk to 5.8 GHz. I am running W7 on my laptop if it means something.

  I have doen the FAX test in the installation manual and the HP FAX and it seems to work fine. It prints very well and we really like the wireless capability. BUT THE ECHO IN THE ANSWERING MACHINE FEATURES ARE A REAL DISAPPOINTMENT.

  This is now resolved. The phone I was using was bluetooth enabled and has been recognized by my laptop and, essentially, got almost at the same time recorded by the responder.

• How can I buy tokens to play poker zynga with an ITunes gift card that I download on my ITunes store account. the system on my IPhone gave me the following message "your purchase cannot be completed, to contact Itunes support support a.

  How can I buy tokens to play poker zynga with an ITunes gift card that I download on my ITunes store account. the system on my IPhone gave me the following message "your purchase cannot be completed, to contact Itunes support support on this Web site, www.apple.com/support/itunes/ww/.

  Click here and ask for help from the staff of the iTunes Store.

  (145085)