iPhone stuck in mode headphones, no sound except the ringtone, but work helmets.

Similar Questions

• Tecra A8 PTA83E - sound in the speakers but work helmet

  Hello

  I recently reinstalled my laptop with a new copy of Windows xp pro. After installing all the drivers where installed correctly, but I have no sound.

  When I put my helmet I can perceive a very low noise.

  Tried almost everything posted on the forums but no luck.

  Someone at - it solution

  Kind regards

  > When I put my helmet I can perceive a very low noise.
  This means that the pilot is ok and possibly that the volume should be increased

  Reach:
  (1) control Panel-> sounds, speech, and Audio Devices section
  (2) select sounds and Audio devices
  (3) sound now and the Group of devices Audio will appear.
  (4) in reading his article click Volume
  (5) in the control of the Volume Group on all controls volume max (foot)

  If this does not help, check out this FAQ from Toshiba:
  http://APS2.toshiba-tro.de/KB0/TSB7C021B0001R01.htm

• When I start RCT3, I can hear the sound of the game, but the image disappears. It's almost as if the monitor is disconnected from the computer. This could be the cause?

  Original title: race Roller Coaster Tycoon 3

  When I start RCT3, I can hear the sound of the game, but the image disappears. It's almost as if the monitor is disconnected from the computer. This could be the cause?

  Hi Redbaron666,

  Have you checked if the game works the clean boot?

  I see that Rollercoaster Tycoon 3 is not compatible with Windows 7 which could be the cause of this problem:

  Windows 7 Compatibility Center

  Method 1: You can run the game in compatibility mode and then check

  Make older programs in this version of Windows

  http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows

  Thanks and greetings

  Ajay K

  Microsoft Answers Support Engineer
  ***************************************************************************
  Visit our Microsoft answers feedback Forum and let us know what you think.

• 6 iPhone stuck! Cannot restore, update or withdraw the recovery mode

  Hello

  I wonder if someone could help.

  I saved my iphone yesterday and tried to install the update. He failed and went into recovery mode.

  After that an update for itunes popped up, so I installed. Tried to update again and it failed. Now, when I connect the phone to Itunes it says either update or restore. According to I try, it won't work. Says that iphone may not be detected despite me having the option to eject it before, either the update or restore process.

  At the moment I can't do anything with it

  Hello. Try the following steps:

  1 press and hold and press Home and Power for 10 seconds to reload your iPhone. If it is still stuck on the Apple logo, you will need to put it in recovery mode.

  2. connect the iPhone to your computer via the USB cable (make sure that the latest version of iTunes is installed).

  3. hold the Home and Power button for 10 seconds. Then release the power button but continue to press the home button.

  4. you will see connect to iTunes screen and you can release the Home button.

  5. now you can restore your iPhone with iTunes.

• No sound from the speakers, but the headphone jack works fine

  Original title: computer with no sound

  My computer has no sound coming from the speakers, but the headphone jack works fine. Can someone help me with this?

  Hi jbreezy,.

  We recommend you to check if the speaker is defined as default playback on your computer device. To do this, try the following steps:
  a. right click on the sound/volume icon in the right corner of the task bar, then click on "adjust audio properties".
  b. click on the Volume tab, click Advanced under Speaker settings, select the speaker and click ok.
  c. click on the tab Audio, audio playback device, select default.
  d. click apply and then click ok.
  e. check if the problem persists.

  For additional troubleshooting steps, see How to fix the sound problems in Windows XP

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Can I turn off all notifications except the ringtone?

  Hello

  I keep ring/silent switch from my iPhone on silent all day, as I work in a space where the sound of notifications would be troublesome for others. However, this means that I miss all the phone calls I get, like the vibration is too low to attract my attention.

  Is it possible to silence all notifications except the ringing of the phone? The only way I can think to do is to manually disable sound notifications for each application. I hope that there is an easier way.

  Nancy wrote:

  Hello

  I keep ring/silent switch from my iPhone on silent all day, as I work in a space where the sound of notifications would be troublesome for others. However, this means that I miss all the phone calls I get, like the vibration is too low to attract my attention.

  Is it possible to silence all notifications except the ringing of the phone? The only way I can think to do is to manually disable sound notifications for each application. I hope that there is an easier way.

  No sorry... you should watch in turn on the led flash... This works when your phone is locked, and when you get a notification it flashes... settings - accessibility - led flash for alerts - suite.

• NVIDIA HDMI output - not plugged in (?) = no sound on the TV, but great picture!

  Hello

  I'm not very experienced in the computer, but I know now that the connection from your laptop to a flat screen HDMI cable TV is not as easy as it should be...

  Description of the problem: no sound, but the big picture on the TV when connecting to my HP dv7 entertainment PC through HDMI to it. Specifically: for NVIDIA HDMI output icon is grey and not active in the "pilot sounds and reading - menu" - you can not simply give (other icons that are active are: speakers and headphones double, double independent headphone & SPDIF). You can also see the TV under "Control panel" > "Devices and printers" - so the tv is connected. In Device Manager, I see that I have 2 sound processors (?) "IDT High Definition Audio CODEC" and "NVIDIA High Definition Audio" - I don't know one that is used for the HDMI connection.

  I have at my own risk installed the latest driver (?) for my graphics (NVIDIA Geforce 9600 M GT) - before I did, the NVIDIA HDMI output icon participated actively in the "... sound"-menu (so you can turn it, etc.)- but no sound on the TV and then either...

  I suspect there to be something wrong with the drivers for my graphics card or processor... or maybe you can't send sound to the tv with my cable? It's a standard HDMI cable...

  Laptop model nr: HP Pavilion dv7-1094eo

  Operating system: Windows 7 Professional 64-bit don't know ServicePack... .

  Graphics card: NVIDIA GeForce 9600M GT

  HDMI cable, tv LCD Philips model: 37PFL7605H

  If someone could help please advise me on what drivers to install or anything else, I would be very grateful!

  / Marie
  

  First do you uninstall IDT High-Definition Audio CODEC Driver and NVIDIA GeForce 9600 M GT drivers by going to

  Control Panel\Programs\Programs and features.

  In case if request you a restart of the computer, please make sure that restart you one after the other. Do NOT avoid restarting the computer.  So go ahead and download view updated and audio drivers from the HP website here.

  Yet once, after installation if you are prompted to restart the computer, go ahead and restart the computer. Once done, go to:

  Control Panel\Hardware and the sound and click on sound. On the Read tab, right-click on the white (empty) space and you will see 2 options (see the disabled devices and show disconnected devices). Make sure that both options are checked for all devices listed reading.

  Now, right click on the option to output HDMI device and make sure that the option "set as default device" is selected for the sound of the external display during playback picture on external monitor.

• No sound from the computer but the sound card does not work correctly

  I have a new computer, but can't get any sound through the screen (not new).   The system tells me that I have a sound card and that it works correctly.   Any ideas?

  Hello

  ·          What version of the operating system is installed on the computer?

  ·          When the issue started?

  However, try the steps in the following article:

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

• Click on 'no sound' in the settings, but sounds aren't going away

  restarted too.  the sounds are the 'clicks' heard when switching from one screen to another on the web or from one folder to another on your computer

  Hello

  As you have already followed the steps for no sound option by default in the Windows sound scheme I suggest you to refer to the steps below and check if changing the values in Registory helps solve the issue.

  (a) open the registry editor.

  Note:

  Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  (a) http://support.microsoft.com/kb/322756

  (b) in the registry editor, navigate to the following registry key:

  HKEY_USERS\. DEFAULT\AppEvents\Schemes

  Create the following value (SZ):

  By default

  And give it a value of. NONE

  (c) close the registry editor.

  Note:

  New user who will now log on to this computer will have the model sounds "No. Sounds" applied.

• laptop stops shortly after the start, but works well in safe mode / command after chkdk or ckdsk/r

  Problem 1: There are months, my two year old Toshiba Satellite L655 s5096 started losing charge the battery even when it is plugged.
  Sometimes, the problem was solved by using a different wall outlet. I replaced the battery, but eventually the problem comes back.

  Problem 2: at the same time that the problems loading starts, Windows has stopped booting normally. Sometimes repair or restoration leads to a normal start, but sometimes I run Chkdsk/r (Chkdsk sometimes the only works [!]) Mode through safe mode w/Command Prompt.

  Problem 3: There are two days of problems 1 and 2 reappeared, but a few minutes after that Windows starts, my machine stops, even if I am able to run Wndows in Mode safe mode w/network.

  I am correct in surmising that this isn't a motherboard (hardware) problem? I don't really want to have to replace this machine if I don't have to. Is this a Windows problem? Upgrade to Windows 8 would solve the problem? Or is it the result of the virus that escaped my Avast scans?

  I'll install Windows 8 when I checked my automatic online data storage works.

  Hi Denise,

  Thanks for posting your question in the Microsoft Community forum.

  I understand that the computer shuts down shortly after starting. I'll help you with this problem.

  1. what security software is installed?

  2. are you sure the workload problem is not limited to a faulty wall unit?

  3. have you checked with the manufacturer of the computer if it is not a battery problem?

  To resolve this issue, let us try these methods:

  Method 1.

  You can create a new power plan and check if that helps.

  Power plans: frequently asked questions: http://windows.microsoft.com/en-ca/windows7/power-plans-frequently-asked-questions

  Method 2.

  Keep the battery power: http://windows.microsoft.com/en-ca/windows7/conserving-battery-power

  Method 3.

  You can remove the battery and connect the power cable from the wall cabinet and check. If the computer does not stop after the restart, then it might be a problem with the battery.

  For any question related to Windows, please do not hesitate to contact us and we will be happy to help you.

• When you use an HDMI cable to watch movies on the tv I have no sound on the TV, but have sound on the ideas of laptop.any

  Has stopped working when I tried to update DFX audio enhancer that have not installed the driver and lost all the audio outputs. Uninstalled DFX and used problem checker who restored the audio, but not the HDMI taken even if I get the image on the TV but no sound.

  You don't say what version of Windows you use, but try to make sure that you have selected as default playback device here HDMI:

  Start--> Contol Panel-> Sound-> playback tab

  If you have Windows Vista or Windows 7.

  If you post back please tell us your version of Windows.

• BIG BUG: Pre stuck on mode headphones! Help

  I was listening to music on my pre and had plugged my earplugs I call then I unplugged them and now I can only make calls using the speakerphone or bluetooth headset and the internal speaker stopped working. During a call, if I look at the icons at the bottom of the screen of dial pad, left down to switch to speaker mode icon is now an icon of headphones, and if I press it, it goes into speakerphone mode. I can't go back to the normal mode. I restarted my phone several times, tried everything I could, it has been 2 days and still can not make a normal call.

  Please help, and no, I don't want to reformat my phone

  Sometimes the switch inside the headphone jack can get stuck

  Try to take your helmet and inserting and removing the decision-making of several times and see if the audio returns.

• Satellite A50 no sound on the speakers but headphones work fine

  Hello

  Satellite A50, Win Xp, its installed driver, the speakers are not silent, but when I use the headphones the sound is ok.
  Speakers do not work!
  There are two of them, I opened the laptop there are two sheets separated
  Are the speakers are down?

  But how it comes together at the same time are down?
  Is there any other configuration I need to do?

  Help, please
  Thank you

  Hello

  Maybe the speakers are not defective but the small switch located in the dysfunctions of helmet?  :|
  The little switch turns Mute speakers when headphones are connected.
  Try to move the headset jack a little bit maybe you will notice a few differences

  But just a question; you see yellow exclamation marks in Device Manager? Have you tried reinstalling the audio driver?
  If this isn't the case, then I recommend to reinstall!

• Aspire One speaker/headphone - no sound when the earphone plug unless the defect of the device is reset

  If the speakers are enabled when you connect headphones, headphone does not work unless I go into the control panel playback settings and change the headphones 'by default'.  Then to return to the speakers when headphones are removed, the procedure is reversed to set the speakers 'by default'.  in the Panel of reading the speaker shows option 'speak' not the typical ' speaker/headset '.  The option for headset is "helmet" that is correct.

  Is it true that the desired device should be selected by default every time?  I find it odd and very annoying.  In general the speaker option would show two 'speaker/headset' so that when plugged in or unplugged the headset you can go back between the speakers and the headphones.  In this situation with just listed "speakers" is not possible.  Anyone else having this problem.

  Once chosen as a default value, each device is functioning.  With the help of Windows 10.  Everything else seems ok.

  have you tried to uninstall your audio device from Device Manager and reboot? I know its sounds counter productive, but often, when you uninstall something, then the system recognizes that you have a device installed, it re - installs the default drivers of factorty for device of theat and Voila! It works somehow. A little nutty in how I have described, but try it, simply right click on your audio device from the Device Manager and select uninstall, it will give you a window with something like "You are about to uninstall Yada, Yada Yasda" but follow through, then restart. I have fixed this way before from udio. Don't forget to restart.

• Pavilion 23xi monitor - no sound - tried the troubleshooter but got stuck.

  Help would be welcome... I plugged the computer laptop hp pavilion hp pavilion 23 15 x 1 and no sound. crossed pages in case of problems, but the HTMI does not appear on the sound options.

  GRAT Banhien - you are absolutely right - no speaker - so worked on it and it now comes through my pc... Thanks a lot - definitely looking forward to a break at Christmas!