IPSec site to site VPN cisco VPN client routing problem and

Hello

I'm really stuck with the configuration of ipsec site to site vpn (hub to spoke, multiple rays) with cisco vpn remote client access to this vpn.

The problem is with remote access - cisco vpn client access - I can communicate with hub lan - but I need also communication of all lans speaks of the cisco vpn client.

There are on the shelves, there is no material used cisco - routers DLINK.

Someone told me that it is possible to use NAT to translate remote access IP-lan-HUB customers and thus allow communication - but I'm unable to set up and operate.

Can someone help me please?

Thank you

Peter

RAYS - not cisco devices / another provider

Cisco 1841 HSEC HUB:

crypto ISAKMP policy 1

BA 3des

preshared authentication

Group 2

ISAKMP crypto key x xx address no.-xauth

!

the group x crypto isakmp client configuration

x key

pool vpnclientpool

ACL 190

include-local-lan

!

86400 seconds, duration of life crypto ipsec security association

Crypto ipsec transform-set esp-3des esp-sha-hmac 1cisco

!

Crypto-map dynamic dynmap 10

Set transform-set 1cisco

!

card crypto ETH0 client authentication list userauthen

card crypto isakmp authorization list groupauthor ETH0

client configuration address card crypto ETH0 answer

ETH0 1 ipsec-isakmp crypto map

set peer x

Set transform-set 1cisco

PFS group2 Set

match address 180

card ETH0 10-isakmp ipsec crypto dynamic dynmap

!

!

interface FastEthernet0/1

Description $ES_WAN$

card crypto ETH0

!

IP local pool vpnclientpool 192.168.200.100 192.168.200.150

!

!

overload of IP nat inside source list LOCAL interface FastEthernet0/1

!

IP access-list extended LOCAL

deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

deny ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

IP 192.168.7.0 allow 0.0.0.255 any

!

access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

!

How the DLINK has been configured for traffic between the site to site VPN subnets? You are able to add multiple remote subnets on DLINK? If you can, then you must add the pool of Client VPN subnet.

Alternatively, if you cannot add multiple subnet on DLINK router, you can change the pool of Client VPN 192.168.6.0/24, and on the crypto ACL between the site to site VPN, you must edit the 180 existing ACL

DE:

access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

access-list 180 allow ip 192.168.200.0 0.0.0.255 192.168.1.0 0.0.0.255

TO:

access-list 180 allow ip 192.168.6.0 0.0.1.255 192.168.1.0 0.0.0.255

Also change the ACL 190 split tunnel:

DE:

access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.200.0 0.0.0.255

TO:

access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.6.0 0.0.0.255

access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255

Finally, replace the remote subnet 192.168.7.0/255.255.255.0 192.168.6.0/255.255.254.0 DLINK.

Hope that helps.

Tags: Cisco Security

Similar Questions

  • 1710 VPN and VPN Client - routing problem '' maybe. ''

    Hello

    I was able to get with 3DES and CISCO VPN Client 3.6.1 1710. with permission of local aaa.

    When I am connected to the VPN I can ping to the IP address of the VPN router

    (24.x.x.x.) and I can ping to the router's internal interface (192.168.x.x).

    The problem is that I can't ping anything else - for example: hosts in the enterprise network (192.168.x.x).

    Configuration:

    The router's internal IP address: 192.168.x.x

    The router's external IP address: 24.x.x.x

    ippool for customers: 10.10.10.x

    The IP address of the Client after the connection is correct: 10.0.0.x (from pool)

    Maybe I'm missing something in 1710 confg? I have NAT interface internal? The default gateway of the net is FreeBSD, not the router of 1710 system.

    All ideas are welcome.

    Miro Pendev

    TI Administrstor

    Quite often, you will lose the first ping because an ARP must be sent and responded to, but if you get the subsequent pings, then it's OK.

    For what is able to browse the Internet while the tunnel is up, you must enable split tunneling. Add the following:

    > access-list 110 permit ip 192.168.1.0 0.0.0.255 192.168.1.0 0.0.0.255

    > isakmp crypto client configuration group my_usergroup

    > acl 110

    This means that the client will only encrypt the traffic to the 192.168.1.0 network, all other traffic shuts down in the clear on the Internet.

  • Site to site VPN with router IOS

    I want to create a VPN site-to site on the Internet. On the remote site, aside from the VPN to the head office, there should be no traffic not allowed in internal from the Internet to the network and that there should be no traffic from the internal network to the Internet allowed. The internal network will run a private 192.168.x.x address range.

    I'm going to use a Cisco 2811 router integrated of services on the remote site and this will last an IPSec VPN that will end a hub at Headquarters. I understand that this router has an IOS and IPS firewall built in.

    Would I be right in thinking that because I don't want to have access to the Internet (except VPN) or should I configure IOS firewall features on the router? And there is no point in the configuration of the features IPS wouldn't?

    My thought is that only an entry in list of unique access to deny pi a whole applied inbound to the interface that connects to the Internet would be the best strategy. I think that the command "sysopt connection permit-ipsec" should allow the VPN to form even with the ip address to deny any any ACL (or is it just a Pix command? If Yes, then I have to allow ESP and UDP 500 (ISAKMP) from the public address of the hub at Headquarters to allow the VPN to form wouldn't I?).

    Think I'll probably expand slightly the access list to allow the icmp Protocol, ssh and https traffic from the IP address of firewall seat outside so that I can monitor the remote site and access it safely if the fail VPN.

    And I wouldn't need one access list on the interface connected to the internal network I would like because the range of addresses would be not routable, so they would not be able to initiate connections to the Internet (all the trffic to the remote site is specified under a valuable traffic to bring up the VPN)

    Use one of the IOS Firewall inspect commands or the IPS would be useless and have no effect in this case wouldn't it?

    I really just need to know if the ip address to deny any any ACL on the external interface on the remote site is the best solution (and the simplest), and whether it will be safe.

    We used to use fiewalls Pix for remote VPN site to site, Amazon refuse incoming connections on the external interface by default but now I have been informed that these series 2800 routers will be used later, so I would get my thoughts straight and be able to build safe to do the same work all existing PIX are doing (they are all installed for just the VPN at Headquarters as in) the first paragraph).

    I would like any advice or thoughts on the subject. I don't know there must be a ton of people who put routers for the same purpose.

    Thank you in advance.

    Pete.

    Pete

    I did a lot of implementations site VPN to another using IOS routers. They work very well. Based on my experience I offer these comments and I hope that they will help you:

    -you don't want a list of incoming access on the external interface, but you want more in it than simply refuse an ip. There is no permit-ipsec sysopt connection in IOS so you want to certainly allowed ISAKMP and IPSec/ESP. I suggest that you also want to allow SSH. I would like to allow ICMP but only starting from the address space of the network head end. I do not allow HTTPS since I generally do not allow the http server on the router. If you want HTTPS then certainly enable it. To facilitate the ping and traceroute on the remote I frequently allow icmp echo-reply, timeout and unreachable port from any source.

    -I want to put an inside interface access list. There are certain types of traffic that I don't want to send from the Remote LAN. I have usually refuse any trap SNMP or snmp for LAN devices and refuse out of the local network icmp redirects. I also often configure RPF controls inside interface to catch any device which is misconfigured.

    -If you want to allow SSH when the VPN is not active (and I highly recommend that you do) then you will probably need to configure at least 1 (and maybe more) users and password of the router ID. And you want to configure authentication on the vty use local authentication if the head end authentication server is not available.

    -I'm not clear from your description if you plan to run a dynamic routing via the VPN Protocol. I wish I had a dynamic routing protocol because I want to announce a default route to the remote control via the VPN. I do not locally configure a default route on the remote router. This way if the VPN tunnel is up there is a default route pointing to the tunnel and if the VPN tunnel is not up then there is no local route by default and users on the remote database can not access the Internet. It is a simple and very effective method to ensure that all user traffic must pass through the central site.

    -regarding the routes defined on the remote router, my approach is that I define a static route for the endpoint of the tunnel to allow the tunnel to implement and I set up static routes for the subnet to the head of line I can SSH. And I do not configure other static routes the on the remote router.

    -You probably want to disable cdp on the external interface and also to disable the proxy-arp (and I don't make any ip unreachable).

    -There is frequently a problem when using VPN site-to-site with fragmentation. If a device on the local network sends a frame of maximum size, and then the router needs to add additional headers for IPSec, then the frame is too large and requires fragmentation. I like to use tcp adjust-mss ip to control the chunk size for TCP traffic and avoid any problems with fragmentation.

    -I don't think you want to set up the firewall or IPS from the features of IOS on the 2811.

    I hope that your application is fine and that my suggestions could be useful.

    [edit] after posting my response, I read through your post again and realize that you make to a VPN concentrator. The approach I have proposed on the execution of a routing protocol works for me because I usually have a router IOS in mind. It would not work to connect to a hub.

    HTH

    Rick

  • Remote IPSec VPN - client Windows 7 and ASA 5505

    Hello

    I'm having trouble with configuring IPSec VPN with Cisco ASA 5505 and Windows 7 client native VPN remotely. My client PC Gets the VPN IP pool address and can access a remote network behind ASA, but then I lose my internet connection. I read that this should be a problem with the split tunneling, but I did as it says here and no luck.

    Windows VPN Client settings, if I uncheck "use default gateway on remote network" I have an internet connection (given that the customer is using a local gateway), but then I can't ping remote network.

    In the log, I see the warnings of this type:

    TCP connection of disassembly 256 for outside:192.168.150.1/49562 to outside:213.199.181.90/80 duration 0: 00:00 0 stream bytes is a loopback (cisco)

    I have attached my configuration file (without configuring split tunneling, I tried). If you need additional newspapers, I'll send them right away.

    Thank you for your help.

    Petar Koraca

    That's what you would have needed on versions 8.3 and earlier versions:

    permit same-security-traffic intra-interface

    Global 1 interface (outside)

    NAT (outside) 1 192.168.150.0 255.255.255.0

    However I see that you are running 8.4 so I think that all you need is this (I never did on 8.4 so it may not be accurate)

    permit same-security-traffic intra-interface

    network of the NETWORK_OBJ_192.168.150.0_24 object

    dynamic NAT interface (outdoors, outdoor)

    Give it a shot and let me know how it goes.

  • Site to site VPN (ASA-> router IOS, with two interfaces) help

    Dear,

    I need help to configure VPN from Site to Site of cisco ASA to the IOS router, the router has 2 WAN links, a primary and secondary backup.

    There was only a single week of link there is, now we have installed the second link as a backup, we use OSPF as the routing protocol.

    VPN with simple link worked fine, now, when the main link fails the network is down.

    Waiting for response.

    There is an easy solution.  On the router, you must terminate the VPN on the loopback interface.

    something like this:

    interface lo0

    IP x.x.x.x where x.x.x.x

    card crypto-address lo0

    interface wan_1

    vpn crypto card

    interface wan_2

    vpn crypto card

    One condition is that the loopback interface has accessible by the device of the SAA.

  • Internet access with VPN Client to ASA and full effect tunnel

    I'm trying to migrate our concentrator at our new 5520 s ASA. The concentrator has been used only for VPN Client connections, and I have not the easiest road. However, I, for some reason, can't access to internet through our business network when I've got profiles with lots of tunneling.

    I've included the configuration file, with many public IP information and omitted site-to-site tunnels. I left all the relevant stuff on tunnel-groups and group strategies concerning connectivity of VPN clients. The range of addresses that I use for VPN clients is 172.16.254.0/24. The group, with what I'm trying to access the internet "adsmgt" and the complete tunnel to our network part is fine.

    As always, any help is appreciated. Thank you!

    Hüseyin... good to see you come back.. bud, yes try these Hüseyin sugesstiong... If we looked to be ok, we'll try a different approach...

    IM thinking too, because complete tunnel is (no separation) Jim ASA has to go back for the outbound traffic from the internet, a permit same-security-traffic intra-interface, instruction should be able to do it... but Jim start by Hüseyin suggestions.

    Rgds

    Jorge

  • ASA VPN server and vpn client router 871

    Hi all

    I have ASA 5510 as simple VPN server and 871 router as simple VPN client. I want to have the user ID and permanent password on 871 and not to re - enter username and password since 871 uses dynamic IP address and every time I have to ' cry ipsec client ezvpn xauth "and type user name and password.

    any suggestions would be much appreciated.

    Thank you

    Alex

    Do "crypto ipsec client ezvpn show ' on 871, does say:

    ...

    Save password: refused

    ...

    ezVPN server dictates the client if it can automatically connect with saved password.

    Set "enable password storage" under the group policy on the ASA.

    Kind regards

    Roman

  • VPN client: What ports and protocols?

    Anyone know which ports and protocols are used by the cisco VPN client? (Telco needs this info, because the VPN client does not work in its network)

    I know of UDP/500 (ISAKMP)

    Erik

    Erik,

    In addition to ISAKMP, Protocol ESP 50 you and, possibly, NAT - T which is UDP/4500.

    Andy

  • ASA problem inside the VPN client routing

    Hello

    I have a problem where I can't reach the VPN clients with their vpn IP pool from the inside or the asa itself. Connect VPN clients can access internal network very well. I have no nat configured for the pool of vpn and packet trace crypt packages and puts it into the tunnel. I'm not sure what's wrong.

    Here are a few relevant config:

    network object obj - 192.168.245.0

    192.168.245.0 subnet 255.255.255.0

    192.168.245.1 - 192.168.245.50 vpn IP local pool

    NAT (inside, outside) static source any any destination static obj - 192.168.245.0 obj - 192.168.245.0 no-proxy-arp-search to itinerary

    Out of Packet trace:

    Firewall # entry packet - trace inside the x.x.x.x icmp 8 0 192.168.245.33

    Phase: 1

    Type: ACCESS-LIST

    Subtype:

    Result: ALLOW

    Config:

    Implicit rule

    Additional information:

    MAC access list

    Phase: 2

    Type:-ROUTE SEARCH

    Subtype: entry

    Result: ALLOW

    Config:

    Additional information:

    in 192.168.245.33 255.255.255.255 outside

    Phase: 3

    Type: ACCESS-LIST

    Subtype: Journal

    Result: ALLOW

    Config:

    Access-group acl-Interior interface inside

    access list acl-Interior extended icmp permitted an echo

    Additional information:

    Phase: 4

    Type: IP-OPTIONS

    Subtype:

    Result: ALLOW

    Config:

    Additional information:

    Phase: 5

    Type: INSPECT

    Subtype: np - inspect

    Result: ALLOW

    Config:

    Additional information:

    Phase: 6

    Type:

    Subtype:

    Result: ALLOW

    Config:

    Additional information:

    Phase: 7

    Type: NAT

    Subtype:

    Result: ALLOW

    Config:

    NAT (inside, outside) static source any any destination static obj - 192.168.245.0

    obj - 192.168.245.0 no-proxy-arp-search to itinerary

    Additional information:

    Definition of static 0/x.x.x.x-x.x.x.x/0

    Phase: 8

    Type: VPN

    Subtype: encrypt

    Result: ALLOW

    Config:

    Additional information:

    Phase: 9

    Type: CREATING STREAMS

    Subtype:

    Result: ALLOW

    Config:

    Additional information:

    New workflow created with the 277723432 id, package sent to the next module

    Result:

    input interface: inside

    entry status: to the top

    entry-line-status: to the top

    output interface: outside

    the status of the output: to the top

    output-line-status: to the top

    Action: allow

    There is no route to the address pool of vpn. Maybe that's the problem? I don't know than that used to work before we went to 8.4.

    Check if the firewall is enabled on your host from the client ravpn and blocking your pings.

  • Newbie Help Needed: Cisco 1941 router site to site VPN traffic routing issue

    Hello

    Please I need help with a VPN site-to site, I installed a router Cisco 1941 and a VPN concentrator based on Linux (Sophos UTM).

    The VPN is established between them, but I can't say the cisco router to send and receive traffic through the tunnel.

    Please, what missing am me?

    A few exits:

    ISAKMP crypto to show her:

    isakmp crypto #show her

    IPv4 Crypto ISAKMP Security Association

    DST CBC conn-State id

    62.173.32.122 62.173.32.50 QM_IDLE 1045 ACTIVE

    IPv6 Crypto ISAKMP Security Association

    Crypto ipsec to show her:

    Interface: GigabitEthernet0/0

    Tag crypto map: QRIOSMAP, local addr 62.173.32.122

    protégé of the vrf: (none)

    local ident (addr, mask, prot, port): (192.168.20.0/255.255.255.0/0/0)

    Remote ident (addr, mask, prot, port): (192.168.2.0/255.255.255.0/0/0)

    current_peer 62.173.32.50 port 500

    LICENCE, flags is {origin_is_acl},

    #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

    #pkts decaps: 52, #pkts decrypt: 52, #pkts check: 52

    compressed #pkts: 0, unzipped #pkts: 0

    #pkts uncompressed: 0, #pkts compr. has failed: 0

    #pkts not unpacked: 0, #pkts decompress failed: 0

    Errors #send 0, #recv 0 errors

    local crypto endpt. : 62.173.32.122, remote Start crypto. : 62.173.32.50

    Path mtu 1500, mtu 1500 ip, ip mtu IDB GigabitEthernet0/0

    current outbound SPI: 0x4D7E4817 (1300121623)

    PFS (Y/N): Y, Diffie-Hellman group: group2

    SAS of the esp on arrival:

    SPI: 0xEACF9A (15388570)

    transform: esp-3des esp-md5-hmac.

    running parameters = {Tunnel}

    Conn ID: 2277, flow_id: VPN:277 on board, sibling_flags 80000046, crypto card: QRIOSMAP

    calendar of his: service life remaining (k/s) key: (4491222/1015)

    Size IV: 8 bytes

    support for replay detection: Y

    Status: ACTIVE

    Please see my config:

    crypto ISAKMP policy 1

    BA 3des

    md5 hash

    preshared authentication

    Group 2

    encryption... isakmp key address 62.X.X... 50

    ISAKMP crypto keepalive 10 periodicals

    !

    !

    Crypto ipsec transform-set esp-3des esp-md5-hmac TS-QRIOS

    !

    QRIOSMAP 10 ipsec-isakmp crypto map

    peer 62.X.X set... 50

    transformation-TS-QRIOS game

    PFS group2 Set

    match address 100

    !

    !

    !

    !

    !

    interface GigabitEthernet0/0

    Description WAN CONNECTION

    62.X.X IP... 124 255.255.255.248 secondary

    62.X.X IP... 123 255.255.255.248 secondary

    62.X.X IP... 122 255.255.255.248

    NAT outside IP

    IP virtual-reassembly in

    automatic duplex

    automatic speed

    card crypto QRIOSMAP

    !

    interface GigabitEthernet0/0.2

    !

    interface GigabitEthernet0/1

    LAN CONNECTION description $ES_LAN$

    address 192.168.20.1 255.255.255.0

    IP nat inside

    IP virtual-reassembly in

    automatic duplex

    automatic speed

    !

    IP nat pool mypool 62.X.X... ... Of 122 62.X.X 122 30 prefix length

    IP nat inside source list 1 pool mypool overload

    overload of IP nat inside source list 100 interface GigabitEthernet0/0

    !

    access-list 1 permit 192.168.20.0 0.0.0.255

    access-list 2 allow 10.2.0.0 0.0.0.255

    Note access-list 100 category QRIOSVPNTRAFFIC = 4

    Note access-list 100 IPSec rule

    access-list 100 permit ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

    access-list 101 permit esp 62.X.X host... 50 62.X.X host... 122

    access list 101 permit udp host 62.X.X... 50 62.X.X... host isakmp EQ. 122

    access-list 101 permit ahp host 62.X.X... 50 62.X.X host... 122

    access-list 101 deny ip any any newspaper

    access-list 110 deny ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

    access-list 110 permit ip 192.168.20.0 0.0.0.255 any

    !

    !

    !

    !

    sheep allowed 10 route map

    corresponds to the IP 110

    The parts of the configuration you posted seem better than earlier versions of the config. The initial problem was that traffic was not in the VPN tunnel. That works now?

    Here are the things I see in your config

    I don't understand the relationship of these 2 static routes by default. It identifies completely the next hop and a mask the bytes of Middleweight of the next hop. Sort of, it seems that they might be the same. But if they were the same, I don't understand why they both make their appearance in the config. Can provide you details?

    IP route 0.0.0.0 0.0.0.0 62.X.X... 121

    IP route 0.0.0.0 0.0.0.0 62.172.32.121

    This static route implies that there is another network (10.2.0/24) connected through the LAN. But there is no other reference to it and especially not for this translation. So I wonder how it works?

    IP route 10.2.0.0 255.255.255.0 192.168.20.2

    In this pair of static routes, the second route is a specific subnet more and would be included in the first and routes for the next of the same break. So I wonder why they are there are. There is not necessarily a problem, but is perhaps something that could be cleaned up.

    IP route 172.17.0.0 255.255.0.0 Tunnel20

    IP route 172.17.2.0 255.255.255.0 Tunnel20

    And these 2 static routes are similar. The second is a more precise indication and would be included in the first. And it is referred to the same next hop. So why have the other?

    IP route 172.18.0.0 255.255.0.0 Tunnel20

    IP route 172.18.0.0 Tunnel20 255.255.255.252

    HTH

    Rick

  • Site to Site VPN Phase 2 problem

    Hello

    I have a problem of IPsec VPN. We have an ASA 5580 to build the VPN site to site with ALU VPN gateway (from partner). The VPN connection is not established. We have checked configurations of devices pair but not found so far any problem. I tried to debug crypto isakmp 127 and got newspaper as below. We always try to find the root cause of this and I could have your advice for the Please this problem? Thank you. (Actual IP address are changed for privacy)

    Apr 08 10:43:45 [IKEv1 DEBUG]: IP = 1.1.1.1, IKE SA proposal # 1, turn # 1 entry overall IKE acceptable matches # 2

    Apr 08 10:43:45 [IKEv1 DEBUG]: IP = 1.1.1.1, build payloads of ISAKMP security

    Apr 08 10:43:45 [IKEv1 DEBUG]: IP = 1.1.1.1, building the Fragmentation VID + load useful functionality

    Apr 08 10:43:45 [IKEv1]: IP = 1.1.1.1, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + HER (1), SELLER (13) + NO (0) total

    Length: 104

    Apr 08 10:43:45 [IKEv1]: IP = 1.1.1.1, Message RECEIPT of IKE_DECODE (msgid = 0) with payloads: HDR + KE (4), NUNCIO (10) + NO (0) total

    Length: 180

    Apr 08 10:43:45 [IKEv1 DEBUG]: IP = 1.1.1.1, processing ke payload

    Apr 08 10:43:45 [IKEv1 DEBUG]: IP = 1.1.1.1, processing payload ISA_KE

    Apr 08 10:43:45 [IKEv1 DEBUG]: IP = 1.1.1.1, processing nonce payload

    Apr 08 10:43:45 [IKEv1 DEBUG]: IP = 1.1.1.1, building ke payload

    Apr 08 10:43:45 [IKEv1 DEBUG]: IP = 1.1.1.1, building nonce payload

    Apr 08 10:43:45 [IKEv1 DEBUG]: IP = 1.1.1.1, build payloads of Cisco Unity VID

    Apr 08 10:43:45 [IKEv1 DEBUG]: IP = 1.1.1.1, constructing payload V6 VID xauth

    Apr 08 10:43:45 [IKEv1 DEBUG]: IP = 1.1.1.1, Send IOS VID

    Apr 08 10:43:45 [IKEv1 DEBUG]: IP = 1.1.1.1, ASA usurpation IOS Vendor ID payload construction (version: 1.0.0 capabilities: 20000001)

    Apr 08 10:43:45 [IKEv1 DEBUG]: IP = 1.1.1.1, build payloads VID

    Apr 08 10:43:45 [IKEv1 DEBUG]: IP = 1.1.1.1, Send Altiga/Cisco VPN3000/Cisco ASA GW VID

    Apr 08 10:43:45 [IKEv1]: IP = 1.1.1.1, connection landed on tunnel_group 1.1.1.1

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, the IP 1.1.1.1, Generating keys for answering =...

    Apr 08 10:43:45 [IKEv1]: IP = 1.1.1.1, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR, KE (4), NUNCIO (10) + (13) seller +.

    SELLER (13), SELLER (13), SELLER (13) + (0) NONE total length: 256

    Apr 08 10:43:45 [IKEv1]: IP = 1.1.1.1, Message RECEIPT of IKE_DECODE (msgid = 0) with payloads: HDR + ID (5) + HASH (8), NOTIFY (11) +.

    NONE (0) overall length: 92

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, payload processing ID

    Apr 08 10:43:45 [IKEv1 DECODER]: Group = 1.1.1.1, IP = 1.1.1.1, ID ID_IPV4_ADDR received

    1.1.1.1

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, the IP 1.1.1.1, payload = hash of treatment

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, calculation of hash for ISAKMP

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, processing notify payload

    Apr 08 10:43:45 [IKEv1]: IP = 1.1.1.1, connection landed on tunnel_group 1.1.1.1

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, building the payload ID

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, build payloads of hash

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, calculation of hash for ISAKMP

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, building dpd vid payload

    Apr 08 10:43:45 [IKEv1]: IP = 1.1.1.1, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + ID (5) + HASH (8), SELLER (13) + NONE

    total length (0): 84

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, PHASE 1 COMPLETED

    Apr 08 10:43:45 [IKEv1]: IP = 1.1.1.1, Keep-alive type for this connection: None

    Apr 08 10:43:45 [IKEv1]: IP = 1.1.1.1, Keep-alives configured on, but the peer does not support persistent (type = None)

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, timer to generate a new key to start P1: 21600 seconds.

    Apr 08 10:43:45 [IKEv1 DECODER]: IP = 1.1.1.1, IKE Responder starting QM: id msg = 0dbcde8a

    Apr 08 10:43:45 [IKEv1]: IP = 1.1.1.1, Message RECEIPT of IKE_DECODE (msgid = dbcde8a) with payloads: HDR + HASH (8) + a (1), NUNCIO (10)

    + KE (4) + ID (5) + ID (5), NONE (0) overall length: 524

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, the IP 1.1.1.1, payload = hash of treatment

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, processing SA payload

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, processing nonce payload

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, processing ke payload

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, ISA_KE to PFS treatment in phase 2

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, payload processing ID

    Apr 08 10:43:45 [IKEv1 DECODER]: Group = 1.1.1.1, IP = 1.1.1.1, ID ID_IPV4_ADDR received

    2.2.2.2

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, data received in payload ID remote Proxy Host: address 2.2.2.2.

    Protocol 0, Port 0

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, payload processing ID

    Apr 08 10:43:45 [IKEv1 DECODER]: Group = 1.1.1.1, IP = 1.1.1.1, ID ID_IPV4_ADDR received

    3.3.3.3

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, data received in payload ID local Proxy Host: address 3.3.3.3,.

    Protocol 0, Port 0

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, the IP 1.1.1.1, QM IsRekeyed its not found old addr =

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto, check card = Outside_map, seq = 1...

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto = Outside_map, seq = 1, ACL does not match

    Proxy src:2.2.2.2 dst: 3.3.3.3 IDs

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto, check card = Outside_map, seq = 2...

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto = Outside_map, seq = 2, ACL does not match

    Proxy src:2.2.2.2 dst: 3.3.3.3 IDs

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto, check card = Outside_map, seq = 3...

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto = Outside_map, seq = 3, ACL does not match

    Proxy src:2.2.2.2 dst: 3.3.3.3 IDs

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto, check card = Outside_map, seq = 4...

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto = Outside_map, seq = 4, ACL does not match

    Proxy src:2.2.2.2 dst: 3.3.3.3 IDs

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto, check card = Outside_map, seq = 5...

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto = Outside_map, seq = 5, ACL does not match

    Proxy src:2.2.2.2 dst: 3.3.3.3 IDs

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto, check card = Outside_map, seq = 6...

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto = Outside_map, seq = 6, ACL does not match

    Proxy src:2.2.2.2 dst: 3.3.3.3 IDs

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto, check card = Outside_map, seq = 7...

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto = Outside_map, seq = 7, ACL does not match

    Proxy src:2.2.2.2 dst: 3.3.3.3 IDs

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto, check card = Outside_map, seq = 8...

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto = Outside_map, seq = 8, ACL does not match

    Proxy src:2.2.2.2 dst: 3.3.3.3 IDs

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto, check card = Outside_map, seq = 9...

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, static checking Card Crypto = Outside_map, seq = 9, ACL does not match

    Proxy src:2.2.2.2 dst: 3.3.3.3 IDs

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, tunnel IPSec rejecting: no entry for crypto for remote proxy card

    2.2.2.2/255.255.255.255/0/0 proxy local 3.3.3.3/255.255.255.255/0/0 on the interface outside

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, sending prevent message

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, constructing empty hash payload

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, build payloads of hash qm

    Apr 08 10:43:45 [IKEv1]: IP = 1.1.1.1, IKE_DECODE SEND Message (msgid = 456db437) with payloads: HDR + HASH (8) + NOTIFY (11) + NONE

    total length (0): 576

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, the IP 1.1.1.1, QM WSF error = (P2 struct & 0x3d51e058, mess id 0xdbcde8a).

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, history of mistake IKE responder QM WSF (struct & 0x3d51e058) .

    : QM_DONE, EV_ERROR--> QM_BLD_MSG2, EV_NEGO_SA--> QM_BLD_MSG2, EV_IS_REKEY--> QM_BLD_MSG2, EV_CONFIRM_SA--> QM_BLD_MSG2, EV_PROC_MSG -.

    > QM_BLD_MSG2, EV_HASH_OK--> QM_BLD_MSG2, NullEvent--> QM_BLD_MSG2, EV_COMP_HASH

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, sending clear/delete with the message of reason

    Apr 08 10:43:45 [IKEv1]: Group = 1.1.1.1, IP = 1.1.1.1, removing counterpart table correlator failed, no match!

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, IKE SA MM:db841932 RRs would end: MM_ACTIVE state flags

    0 x 00010042, refcnt 1, tuncnt 0

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, IKE SA MM:db841932 ending: flags 0 x 01010002, refcnt 0,.

    tuncnt 0

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, sending clear/delete with the message of reason

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, constructing empty hash payload

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, building the payload to delete IKE

    Apr 08 10:43:45 [IKEv1 DEBUG]: Group = 1.1.1.1, IP = 1.1.1.1, build payloads of hash qm

    Apr 08 10:43:45 [IKEv1]: IP = 1.1.1.1, IKE_DECODE SEND Message (msgid = c1606511) with payloads: HDR HASH (8) + DELETE (12) + NONE

    total length (0): 80

    Apr 08 10:43:45 [IKEv1]: ignoring msg SA brand with Iddm 2781184 dead because ITS removal

    Apr 08 10:43:46 [IKEv1]: IP = 1.1.1.1, encrypted packet received with any HIS correspondent, drop

    It is Phase 1 ends successfully, but when the remote end sends the traffic that must match your crypto card and put in place a Phase 2 IPsec SA, it does not match:

    Rejecting the IPSec tunnel: no entry for crypto for remote proxy card

    DoubleCheck that "2.2.2.2 to 3.3.3.3" is to map your end crypto (and that the obverse is located in the remote side).

  • Cisco SA540 - classic routing problem - 0.0.0.0 in static road

    Hello, I am a bit newbie with routing device,

    I had several public IP address

    I got a Cisco Pix 501and want to replace it with a Cisco SA540

    My Wan IP on Pix 501 is 195.68.x.z
    My Lan IP on Pix 501 is 62.23.a.b (and 62.23.a.c,...)

    My rules Pix 501 translation is: inside the interface. inside: everything: 0.0.0.0. Apart from the interface. same as orginal
    My Pix 501 static route: outside | IP address 0.0.0.0. Mask 0.0.0.0. Gateway IP 195.168.x.y | Metric 1

    So when a computer with 62.23.a.X want access to the internet the static route he say to throuw the 195.168.x.y of the IP Address of the gateway (as I undestand)

    I replicate this config on my SA540

    Also, through the Web user interface, I configure the Wan and Lan IP
    and then in the routing menu, I check "Classic routing" so I go to the static Menu to add the same route as in my Pix 501, but I can't put 0.0.0.0 in iP address or IP subnet mask.

    Can someone help me?

    Thank you very much.

    Hello

    I hope this finds you doing well.  Just thought I would add a few things here...

    You have probably seen this, but... Here is the link to the page SA500:

    https://www.myciscocommunity.com/docs/doc-10526

    Yes, when you configure the device as a router, you need to configure routing.  Try to remove the routes and the readd.

    In addition, a little off topic, but if you want to stay with an ASA5505, there used to be a tool that would turn your PIX configus ASA.  I don't remember where this link is now... but it used to fairly simple transition.

    After you have configured the routing, since your internal machine, have you tried a trace route?  On what device the traceroute fails?

    In case you wish to speak to a support representative, here is the link to find the correct number:

    http://www.Cisco.com/en/us/support/tsd_cisco_small_business_support_center_contacts.html

    HTH,

    Andrew Lee Lissitz

  • Troubleshooting IPSec Site to Site VPN between ASA and 1841

    Hi all

    in the past I've implemented several VPN connections between the devices of the SAA. So I thought a site link between an ASA site and 1841 would be easier... But it seems I was mistaken.

    I configured a VPN Site to Site, as it has been described in the Document ID: SDM 110198: IPsec Site to Site VPN between ASA/PIX and an example of IOS Router Configuration (I have not used SDM but CCP).

    I have run the wizards on the ASA with ASDM and the current IOS version 15.1 1841, with CCP.

    It seems to Phase 1 and 2 are coming although my ASA in ADSM reports (monitoring > VPN > VPN statistics > Sessions) a tunnel established with some of the Tx traffic but 0 Rx traffic),

    On the ASA:

    Output of the command: "sh crypto ipsec its peer 217.xx.yy.zz.

    address of the peers: 217.86.154.120
    Crypto map tag: VPN-OUTSIDE, seq num: 2, local addr: 62.aa.bb.cc

    access extensive list ip 192.168.37.0 outside_2_cryptomap_1 allow 255.255.255.0 172.20.2.0 255.255.255.0
    local ident (addr, mask, prot, port): (LAN-A/255.255.255.0/0/0)
    Remote ident (addr, mask, prot, port): (LAN-G/255.255.255.0/0/0)
    current_peer: 217.xx.yy.zz

    #pkts program: 400, #pkts encrypt: 400, #pkts digest: 400
    #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 400, comp #pkts failed: 0, #pkts Dang failed: 0
    success #frag before: 0, failures before #frag: 0, #fragments created: 0
    Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
    #send errors: 0, #recv errors: 0

    local crypto endpt. : 62.aa.bb.cc, remote Start crypto. : 217.xx.yy.zz

    Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
    current outbound SPI: 39135054
    current inbound SPI: B2E9E500

    SAS of the esp on arrival:
    SPI: 0xB2E9E500 (3001672960)
    transform: esp-3des esp-sha-hmac no compression
    running parameters = {L2L, Tunnel, PFS 2 group}
    slot: 0, id_conn: 100327424, crypto-map: VPN-OUTSIDE
    calendar of his: service life remaining (KB/s) key: (4374000/1598)
    Size IV: 8 bytes
    support for replay detection: Y
    Anti-replay bitmap:
    0x00000000 0x00000001
    outgoing esp sas:
    SPI: 0 x 39135054 (957567060)
    transform: esp-3des esp-sha-hmac no compression
    running parameters = {L2L, Tunnel, PFS 2 group}
    slot: 0, id_conn: 100327424, crypto-map: VPN-OUTSIDE
    calendar of his: service life remaining (KB/s) key: (4373976/1598)
    Size IV: 8 bytes
    support for replay detection: Y
    Anti-replay bitmap:
    0x00000000 0x00000001

    Output of the command: "sh crypto isakmp his."

    HIS active: 4
    Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
    Total SA IKE: 4

    IKE Peer: 217.xx.yy.zz
    Type: L2L role: initiator
    Generate a new key: no State: MM_ACTIVE

    On the 1841

    1841 crypto isakmp #sh its
    IPv4 Crypto ISAKMP Security Association
    DST CBC conn-State id
    217.86.154.120 62.153.156.163 QM_IDLE 1002 ACTIVE

    1841 crypto ipsec #sh its

    Interface: Dialer1
    Tag crypto map: SDM_CMAP_1, local addr 217.86.154.120

    protégé of the vrf: (none)
    local ident (addr, mask, prot, port): (172.20.2.0/255.255.255.0/0/0)
    Remote ident (addr, mask, prot, port): (192.168.37.0/255.255.255.0/0/0)
    current_peer 62.153.156.163 port 500
    LICENCE, flags is {origin_is_acl},
    #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
    #pkts decaps: 585, #pkts decrypt: 585, #pkts check: 585
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 0, #pkts compr. has failed: 0
    #pkts not unpacked: 0, #pkts decompress failed: 0
    Errors #send 0, #recv 0 errors

    local crypto endpt. : 217.86.154.120, remote Start crypto. : 62.153.156.163
    Path mtu 1452, ip mtu 1452, ip mtu BID Dialer1
    current outbound SPI: 0xB2E9E500 (3001672960)
    PFS (Y/N): Y, Diffie-Hellman group: group2

    SAS of the esp on arrival:
    SPI: 0 x 39135054 (957567060)
    transform: esp-3des esp-sha-hmac.
    running parameters = {Tunnel}
    Conn ID: 2003, flow_id: FPGA:3, sibling_flags 80000046, card crypto: SDM_CMAP_1
    calendar of his: service life remaining (k/s) key: (4505068/1306)
    Size IV: 8 bytes
    support for replay detection: Y
    Status: ACTIVE

    the arrival ah sas:

    SAS of the CFP on arrival:

    outgoing esp sas:
    SPI: 0xB2E9E500 (3001672960)
    transform: esp-3des esp-sha-hmac.
    running parameters = {Tunnel}
    Conn ID: 2004, flow_id: FPGA:4, sibling_flags 80000046, card crypto: SDM_CMAP_1
    calendar of his: service life remaining (k/s) key: (4505118/1306)
    Size IV: 8 bytes
    support for replay detection: Y
    Status: ACTIVE

    outgoing ah sas:

    outgoing CFP sas:

    Interface: virtual Network1
    Tag crypto map: SDM_CMAP_1, local addr 217.86.154.120

    protégé of the vrf: (none)
    local ident (addr, mask, prot, port): (172.20.2.0/255.255.255.0/0/0)
    Remote ident (addr, mask, prot, port): (192.168.37.0/255.255.255.0/0/0)
    current_peer 62.153.156.163 port 500
    LICENCE, flags is {origin_is_acl},
    #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
    #pkts decaps: 585, #pkts decrypt: 585, #pkts check: 585
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 0, #pkts compr. has failed: 0
    #pkts not unpacked: 0, #pkts decompress failed: 0
    Errors #send 0, #recv 0 errors

    local crypto endpt. : 217.86.154.120, remote Start crypto. : 62.153.156.163
    Path mtu 1452, ip mtu 1452, ip mtu BID Dialer1
    current outbound SPI: 0xB2E9E500 (3001672960)
    PFS (Y/N): Y, Diffie-Hellman group: group2

    SAS of the esp on arrival:
    SPI: 0 x 39135054 (957567060)
    transform: esp-3des esp-sha-hmac.
    running parameters = {Tunnel}
    Conn ID: 2003, flow_id: FPGA:3, sibling_flags 80000046, card crypto: SDM_CMAP_1
    calendar of his: service life remaining (k/s) key: (4505068/1306)
    Size IV: 8 bytes
    support for replay detection: Y
    Status: ACTIVE

    the arrival ah sas:

    SAS of the CFP on arrival:

    outgoing esp sas:
    SPI: 0xB2E9E500 (3001672960)
    transform: esp-3des esp-sha-hmac.
    running parameters = {Tunnel}
    Conn ID: 2004, flow_id: FPGA:4, sibling_flags 80000046, card crypto: SDM_CMAP_1
    calendar of his: service life remaining (k/s) key: (4505118/1306)
    Size IV: 8 bytes
    support for replay detection: Y
    Status: ACTIVE

    outgoing ah sas:

    outgoing CFP sas:

    It seems that the routing on the 1841 is working properly as I can tear down the tunnel and relaunch in scathing a host on the network of 1841, but not vice versa.

    Trounleshoot VPN of the 1841 report shows a message like "the following sources are forwarded through the interface card crypto.      (172.20.2.0 1) go to "Configure-> routing" and correct the routing table.

    I have not found an error on the 1841 config so if one of the guys reading this thread has an idea I appreciate highly suspicion!

    It's the running of the 1841 configuration

    !
    version 15.1
    horodateurs service debug datetime msec
    Log service timestamps datetime msec
    encryption password service
    !
    host name 1841
    !
    boot-start-marker
    start the system flash c1841-adventerprisek9 - mz.151 - 1.T.bin
    boot-end-marker
    !
    logging buffered 51200 notifications
    !
    AAA new-model
    !
    !
    AAA authentication login default local
    !
    AAA - the id of the joint session
    !
    iomem 20 memory size
    clock timezone PCTime 1
    PCTime of summer time clock day March 30, 2003 02:00 October 26, 2003 03:00
    dot11 syslog
    IP source-route
    !
    No dhcp use connected vrf ip
    !
    IP cef
    no ip bootp Server
    IP domain name test
    name of the IP-server 194.25.2.129
    name of the IP-server 194.25.2.130
    name of the IP-server 194.25.2.131
    name of the IP-server 194.25.2.132
    name of the IP-server 194.25.2.133
    No ipv6 cef
    !
    Authenticated MultiLink bundle-name Panel
    !
    !
    object-group network phone
    VoIP phone description
    Home 172.20.2.50
    Home 172.20.2.51
    !
    redundancy
    !
    !
    controller LAN 0/0/0
    atm mode
    Annex symmetrical shdsl DSL-mode B
    !
    !
    crypto ISAKMP policy 1
    BA 3des
    preshared authentication
    Group 2
    isakmp encryption key * address 62.aa.bb.cc
    !
    !
    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
    !
    map SDM_CMAP_1 1 ipsec-isakmp crypto
    Description Tunnel to62.aa.bb.cc
    the value of 62.aa.bb.cc peer
    game of transformation-ESP-3DES-SHA
    PFS group2 Set
    match address 100
    !
    !
    !
    interface FastEthernet0/0
    DMZ description $ FW_OUTSIDE$
    10.10.10.254 IP address 255.255.255.0
    IP nat inside
    IP virtual-reassembly
    automatic duplex
    automatic speed
    !
    interface FastEthernet0/1
    Description $ETH - LAN$ $FW_INSIDE$
    IP 172.20.2.254 255.255.255.0
    IP access-group 100 to
    IP nat inside
    IP virtual-reassembly
    IP tcp adjust-mss 1412
    automatic duplex
    automatic speed
    !
    ATM0/0/0 interface
    no ip address
    No atm ilmi-keepalive
    !
    point-to-point interface ATM0/0/0.1
    PVC 1/32
    PPPoE-client dial-pool-number 1
    !
    !
    interface Dialer1
    Description $FW_OUTSIDE$
    the negotiated IP address
    IP mtu 1452
    NAT outside IP
    IP virtual-reassembly
    encapsulation ppp
    Dialer pool 1
    Dialer-Group 2
    PPP authentication chap callin pap
    PPP chap hostname xxxxxxx
    PPP chap password 7 xxxxxxx8
    PPP pap sent-name of user password xxxxxxx xxxxxxx 7
    map SDM_CMAP_1 crypto
    !
    IP forward-Protocol ND
    IP http server
    local IP http authentication
    IP http secure server
    !
    !
    The dns server IP
    IP nat inside source static tcp 10.10.10.1 808 interface Dialer1 80
    IP nat inside source static tcp 10.10.10.1 25 25 Dialer1 interface
    IP nat inside source overload map route SDM_RMAP_1 interface Dialer1
    IP nat inside source overload map route SDM_RMAP_2 interface Dialer1
    IP route 0.0.0.0 0.0.0.0 Dialer1 permanent
    !
    logging trap notifications
    Note category of access list 1 = 2 CCP_ACL
    access-list 1 permit 172.20.2.0 0.0.0.255
    Note access-list category 2 CCP_ACL = 2
    access-list 2 allow 10.10.10.0 0.0.0.255
    Note access-list 100 category CCP_ACL = 4
    Note access-list 100 IPSec rule
    access-list 100 permit ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
    Note CCP_ACL the access list 101 = 2 category
    Note access-list 101 IPSec rule
    access-list 101 deny ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
    access-list 101 permit ip 172.20.2.0 0.0.0.255 any
    Note access-list 102 CCP_ACL category = 2
    Note access-list 102 IPSec rule
    access-list 102 deny ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
    access-list 102 permit ip 10.10.10.0 0.0.0.255 any
    !

    !
    allowed SDM_RMAP_1 1 route map
    corresponds to the IP 101
    !
    allowed SDM_RMAP_2 1 route map
    corresponds to the IP 102
    !
    !
    control plan
    !
    !
    Line con 0
    line to 0
    line vty 0 4
    length 0
    transport input telnet ssh
    !
    Scheduler allocate 20000 1000
    NTP-Calendar Update
    NTP 172.20.2.250 Server prefer
    end

    As I mentioned previously: suspicion is much appreciated!

    Best regards

    Joerg

    Joerg,

    ASA receives not all VPN packages because IOS does not send anything.

    Try to send packets to the 1841 LAN to LAN of the ASA and see is the "sh cry ips its" on the 1841 increments the encrypted packets (there not)

    The problem seems so on the side of the router.

    I think that is a routing problem, but you only have one default gateway (no other channels on the router).

    The ACL 100 is set to encrypt the traffic between the two subnets.

    It seems that the ACL 101 is also bypassing NAT for VPN traffic.

    Follow these steps:

    Try running traffic of LAN router inside IP (source of ping 192.168.37.x 172.20.2.254) and see if the packages are not through the translation and obtaining encrypted.

    I would also like to delete 100 ACL from the inside interface on the router because it is used for the VPN. You can create an another ACL to apply to the interface.

    Federico.

  • VPN clients hairpining through a tunnel from site to site

    I have a 8.2 (5) ASA 5510 in Site1 and a 8.2 (1) ASA 5505 Site2 they are configured with a tunnel from site to site.

    Each site has VPN clients that connect and I would like to allow customers to access on both sides across the site-to-site tunnel servers.

    I enabled same-security-traffic permit intra-interface I also added the remote networks to access list who made the split tunneling.

    I think I'm doing something wrong with nat, but I don't know, any help would be greatly appreciated.

    Site1 Clients1 (172.17.2.0/24) (10.0.254.0/24)

    ASA Version 8.2 (5)

    !

    hostname site1

    names of

    DNS-guard

    !

    interface Ethernet0/0

    nameif outside

    security-level 0

    IP address site1 255.255.255.240

    !

    interface Ethernet0/1

    nameif inside

    security-level 100

    IP 172.17.2.1 255.255.255.0

    !

    interface Ethernet0/2

    Shutdown

    nameif DMZ

    security-level 0

    IP 10.10.10.1 255.255.255.0

    !

    interface Ethernet0/3

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Management0/0

    nameif management

    security-level 0

    IP 192.168.1.1 255.255.255.0

    management only

    !

    passive FTP mode

    permit same-security-traffic intra-interface

    VPN - UK wide ip 172.17.2.0 access list allow 255.255.255.0 172.18.2.0 255.255.255.0

    access extensive list ip 172.17.2.0 inside_nat0_outbound allow 255.255.255.0 192.168.123.0 255.255.255.0

    access extensive list ip 172.17.2.0 inside_nat0_outbound allow 255.255.255.0 172.18.2.0 255.255.255.0

    access extensive list ip 172.17.2.0 inside_nat0_outbound allow 255.255.255.0 10.0.254.0 255.255.255.0

    Notice of inside_nat0_outbound access-list us Client Server UK

    access extensive list ip 10.0.254.0 inside_nat0_outbound allow 255.255.255.0 172.18.2.0 255.255.255.0

    access extensive list ip 192.168.123.0 inside_nat0_outbound allow 255.255.255.0 10.0.254.0 255.255.255.0

    access extensive list ip 172.18.2.0 inside_nat0_outbound allow 255.255.255.0 10.0.254.0 255.255.255.0

    Standard access list Split_Tunnel_List allow 172.17.2.0 255.255.255.0

    Standard access list Split_Tunnel_List allow 172.18.2.0 255.255.255.0

    Split_Tunnel_List list standard access allowed 192.168.123.0 255.255.255.0

    Split_Tunnel_List of access note list UK VPN Client pool

    Standard access list Split_Tunnel_List allow 172.255.2.0 255.255.255.0

    outside-2 extended access list permit tcp any any eq smtp

    outside-2 extended access list permit tcp any any eq 82

    outside-2 extended access list permit tcp any any eq 81

    outside-2 extended access list permit tcp everything any https eq

    outside-2 extended access list permit tcp any any eq imap4

    outside-2 extended access list permit tcp any any eq ldaps

    outside-2 extended access list permit tcp any any eq pop3

    outside-2 extended access list permit tcp any any eq www

    outside-2 extended access list permit tcp any any eq 5963

    outside-2 extended access list permit tcp any any eq ftp

    outside-2 allowed extended access list tcp any any eq ftp - data

    outside-2 extended access list permit tcp any any eq 3389

    list of access outside-2 extended tcp refuse any any newspaper

    2-outside access list extended deny ip any any newspaper

    outside-2 extended access list deny udp any any newspaper

    allow VPN CLIENTS to access extended list ip 172.17.2.0 255.255.255.0 10.0.254.0 255.255.255.0

    allow VPN CLIENTS to access extended list ip 172.18.2.0 255.255.255.0 10.0.254.0 255.255.255.0

    allow VPN CLIENTS to access extended list 192.168.123.0 ip 255.255.255.0 10.0.254.0 255.255.255.0

    Standard access list VPNClient_splittunnel allow 172.17.2.0 255.255.255.0

    Standard access list VPNClient_splittunnel allow 172.18.2.0 255.255.255.0

    VPNClient_splittunnel list standard access allowed 192.168.123.0 255.255.255.0

    VPNClient_splittunnel of access note list UK VPN Client pool

    Standard access list VPNClient_splittunnel allow 172.255.2.0 255.255.255.0

    VPN-Northwoods extended ip 172.17.2.0 access list allow 255.255.255.0 192.168.123.0 255.255.255.0

    Note to outside_nat0_outbound to access list AD 01/05/13

    access extensive list ip 10.0.254.0 outside_nat0_outbound allow 255.255.255.0 172.18.2.0 255.255.255.0

    pager lines 24

    Enable logging

    debug logging in buffered memory

    asdm of logging of information

    Outside 1500 MTU

    Within 1500 MTU

    MTU 1500 DMZ

    management of MTU 1500

    mask 10.0.254.25 - 10.0.254.45 255.255.255.0 IP local pool VPNUserPool

    ICMP unreachable rate-limit 1 burst-size 1

    don't allow no asdm history

    ARP timeout 14400

    NAT-control

    Global 1 interface (outside)

    NAT (outside) 0-list of access outside_nat0_outbound

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 1 172.17.2.0 255.255.255.0

    public static tcp (indoor, outdoor) interface smtp 172.17.2.200 smtp netmask 255.255.255.255

    public static tcp (indoor, outdoor) interface 82 172.17.2.253 82 netmask 255.255.255.255

    public static tcp (indoor, outdoor) interface 81 192.168.123.253 81 netmask 255.255.255.255

    public static tcp (indoor, outdoor) interface https 172.17.2.10 https netmask 255.255.255.255

    public static tcp (indoor, outdoor) interface 172.17.2.10 imap4 imap4 netmask 255.255.255.255

    public static tcp (indoor, outdoor) interface ldaps 172.17.2.10 ldaps netmask 255.255.255.255

    public static tcp (indoor, outdoor) interface 172.17.2.10 pop3 pop3 netmask 255.255.255.255

    public static tcp (indoor, outdoor) interface www 172.17.2.19 www netmask 255.255.255.255

    public static tcp (indoor, outdoor) interface 5963 172.17.2.108 5963 netmask 255.255.255.255

    public static tcp (indoor, outdoor) interface ftp 172.17.2.7 ftp netmask 255.255.255.255

    public static tcp (indoor, outdoor) interface ftp - data 172.17.2.7 ftp - data netmask 255.255.255.255

    static (inside, outside) tcp 3389 172.17.2.29 interface 3389 netmask 255.255.255.255

    Access-group 2-outside-inside in external interface

    Route outside 0.0.0.0 0.0.0.0 74.213.51.129 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    RADIUS protocol AAA-server DCSI_Auth

    AAA-server host 172.17.2.29 DCSI_Auth (inside)

    key *.

    AAA-server protocol nt AD

    AAA-server AD (inside) host 172.16.1.211

    AAA-server AD (inside) host 172.17.2.29

    the ssh LOCAL console AAA authentication

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set esp - esp-sha-hmac trans_set

    Crypto ipsec transform-set VPN-Client-esp-3des esp-sha-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    Crypto dynamic-map DYN_MAP 20 the value reverse-road

    Crypto-map dynamic outside_dyn_map 20 game of transformation-VPN-Client

    address for correspondence outside_map 20 card crypto VPN - UK

    card crypto outside_map 20 peers set site2

    card crypto outside_map 20 transform-set trans_set

    address for correspondence outside_map 30 card crypto VPN-Northwoods

    card crypto outside_map 30 peers set othersite

    trans_set outside_map 30 transform-set card crypto

    map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

    outside_map interface card crypto outside

    Crypto ca trustpoint _SmartCallHome_ServerCA

    Configure CRL

    crypto isakmp identity address

    crypto ISAKMP allow outside

    crypto ISAKMP policy 10

    preshared authentication

    the Encryption

    sha hash

    Group 2

    lifetime 28800

    crypto ISAKMP policy 20

    preshared authentication

    the Encryption

    md5 hash

    Group 2

    lifetime 28800

    Telnet timeout 5

    SSH timeout 60

    Console timeout 0

    management of 192.168.1.2 - dhcpd address 192.168.1.254

    enable dhcpd management

    !

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    internal Clients_vpn group strategy

    attributes of strategy of group Clients_vpn

    value of server DNS 10.0.1.30

    Protocol-tunnel-VPN IPSec

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list VPNClient_splittunnel

    domain.local value by default-field

    the authentication of the user activation

    tunnel-group VPNclient type remote access

    tunnel-group VPNclient-global attributes

    address pool VPNUserPool

    authentication-server-group DCSI_Auth

    strategy - by default-group Clients_vpn

    tunnel-group VPNclient ipsec-attributes

    pre-shared key *.

    tunnel-group othersite type ipsec-l2l

    othersite group tunnel ipsec-attributes

    pre-shared key *.

    tunnel-group site2 type ipsec-l2l

    tunnel-group ipsec-attributes site2

    pre-shared key *.

    !

    class-map inspection_default

    match default-inspection-traffic

    class-map imblock

    match any

    class-map p2p

    game port tcp eq www

    class-map P2P

    game port tcp eq www

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    maximum message length automatic of customer

    message-length maximum 512

    type of policy-map inspect im bine

    parameters

    msn - im yahoo im Protocol game

    drop connection

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    Review the ip options

    inspect the pptp

    type of policy-card inspect http P2P_HTTP

    parameters

    matches the query uri regex _default_gator

    Journal of the drop connection

    football match request uri regex _default_x-kazaa-network

    Journal of the drop connection

    Policy-map IM_P2P

    class imblock

    inspect the im bine

    class P2P

    inspect the http P2P_HTTP

    !

    global service-policy global_policy

    IM_P2P service-policy inside interface

    context of prompt hostname

    no remote anonymous reporting call

    Cryptochecksum:7717a11f5f2dce11af0f35cee7b4c893

    : end

    Site2 Clients1 (172.18.2.0/24) (172.255.2.0/24)

    ASA Version 8.2 (1)

    !

    names of

    name 172.18.2.2 UKserver

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 172.18.2.1 255.255.255.0

    !

    interface Vlan2

    nameif GuestWiFi

    security-level 0

    IP 192.168.2.1 255.255.255.0

    !

    interface Vlan3

    nameif outside

    security-level 0

    IP address site2 255.255.255.252

    !

    interface Ethernet0/0

    switchport access vlan 3

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    switchport trunk allowed vlan 1-2

    switchport vlan trunk native 2

    switchport mode trunk

    Speed 100

    full duplex

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    passive FTP mode

    permit same-security-traffic intra-interface

    Access extensive list ip 172.18.2.0 USER_VPN allow 255.255.255.0 172.255.2.0 255.255.255.0

    Access extensive list ip 172.17.2.0 USER_VPN allow 255.255.255.0 172.255.2.0 255.255.255.0

    Standard access list VPNClient_splittunnel allow 172.18.2.0 255.255.255.0

    Standard access list VPNClient_splittunnel allow 172.17.2.0 255.255.255.0

    Standard access list VPNClient_splittunnel allow 172.255.2.0 255.255.255.0

    Outside_2_Inside list extended access permit tcp any host otherhost eq smtp

    Outside_2_Inside list extended access permit tcp any host otherhost eq pop3

    Outside_2_Inside list extended access permit tcp any host otherhost eq imap4

    Outside_2_Inside list extended access permit tcp any host otherhost eq www

    Outside_2_Inside list extended access permit tcp any host otherhost eq https

    Outside_2_Inside list extended access permit tcp any host otherhost eq ldap

    Outside_2_Inside list extended access permit tcp any host otherhost eq ldaps

    Outside_2_Inside list extended access permit tcp any host otherhost eq nntp

    Outside_2_Inside list extended access permit tcp any host otherhost eq 135

    Outside_2_Inside list extended access permit tcp any host otherhost eq 102

    Outside_2_Inside list extended access permit tcp any host otherhost eq 390

    Outside_2_Inside list extended access permit tcp any host otherhost eq 3268

    Outside_2_Inside list extended access permit tcp any host otherhost eq 3269

    Outside_2_Inside list extended access permit tcp any host otherhost eq 993

    Outside_2_Inside list extended access permit tcp any host otherhost eq 995

    Outside_2_Inside list extended access permit tcp any host otherhost eq 563

    Outside_2_Inside list extended access permit tcp any host otherhost eq 465

    Outside_2_Inside list extended access permit tcp any host otherhost eq 691

    Outside_2_Inside list extended access permit tcp any host otherhost eq 6667

    Outside_2_Inside list extended access permit tcp any host otherhost eq 994

    Outside_2_Inside access list extended icmp permitted an echo

    Outside_2_Inside list extended access permit icmp any any echo response

    Outside_2_Inside list extended access permit tcp any host site2 eq smtp

    Outside_2_Inside list extended access permit tcp any host site2 eq pop3

    Outside_2_Inside list extended access permit tcp any host site2 eq imap4

    Outside_2_Inside list extended access permit tcp any host site2 eq www

    Outside_2_Inside list extended access permit tcp any host site2 eq https

    Outside_2_Inside list extended access permit tcp any host site2 eq ldap

    Outside_2_Inside list extended access permit tcp any host site2 eq ldaps

    Outside_2_Inside list extended access permit tcp any host site2 eq nntp

    Outside_2_Inside list extended access permit tcp any host site2 eq 135

    Outside_2_Inside list extended access permit tcp any host site2 eq 102

    Outside_2_Inside list extended access permit tcp any host site2 eq 390

    Outside_2_Inside list extended access permit tcp any host site2 eq 3268

    Outside_2_Inside list extended access permit tcp any host site2 eq 3269

    Outside_2_Inside list extended access permit tcp any host site2 eq 993

    Outside_2_Inside list extended access permit tcp any host site2 eq 995

    Outside_2_Inside list extended access permit tcp any host site2 eq 563

    Outside_2_Inside list extended access permit tcp any host site2 eq 465

    Outside_2_Inside list extended access permit tcp any host site2 eq 691

    Outside_2_Inside list extended access permit tcp any host site2 eq 6667

    Outside_2_Inside list extended access permit tcp any host site2 eq 994

    Outside_2_Inside list extended access permit tcp any SIP EQ host site2

    Outside_2_Inside list extended access permit tcp any range of 8000-8005 host site2

    Outside_2_Inside list extended access permit udp any range of 8000-8005 host site2

    Outside_2_Inside list extended access udp allowed any SIP EQ host site2

    Outside_2_Inside tcp extended access list deny any any newspaper

    Outside_2_Inside list extended access deny udp any any newspaper

    VPN - USA 172.255.2.0 ip extended access list allow 255.255.255.0 172.17.2.0 255.255.255.0

    access extensive list ip 172.18.2.0 inside_nat0_outbound allow 255.255.255.0 172.17.2.0 255.255.255.0

    access extensive list ip 172.18.2.0 inside_nat0_outbound allow 255.255.255.0 172.255.2.0 255.255.255.0

    access extensive list ip 172.255.2.0 inside_nat0_outbound allow 255.255.255.0 172.17.2.0 255.255.255.0

    Comment by Split_Tunnel_List-list of access networks to allow via VPN

    Standard access list Split_Tunnel_List allow 172.18.2.0 255.255.255.0

    Standard access list Split_Tunnel_List allow 172.17.2.0 255.255.255.0

    Standard access list Split_Tunnel_List allow 172.255.2.0 255.255.255.0

    Standard access list Split_Tunnel_List allow 10.0.254.0 255.255.255.0

    pager lines 20

    Enable logging

    monitor debug logging

    debug logging in buffered memory

    asdm of logging of information

    Debugging trace record

    Within 1500 MTU

    MTU 1500 GuestWiFi

    Outside 1500 MTU

    IP pool local ClientVPN 172.255.2.100 - 172.255.2.124

    no failover

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm - 621.bin

    don't allow no asdm history

    ARP timeout 14400

    NAT-control

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 1 172.18.2.0 255.255.255.0

    NAT (GuestWiFi) 2 192.168.2.0 255.255.255.0

    public static tcp (indoor, outdoor) interface smtp smtp UKserver netmask 255.255.255.255

    public static tcp (indoor, outdoor) UKserver netmask 255.255.255.255 pop3 pop3 interface

    public static tcp (indoor, outdoor) interface imap4 imap4 netmask 255.255.255.255 UKserver

    public static tcp (indoor, outdoor) interface www UKserver www netmask 255.255.255.255

    public static tcp (indoor, outdoor) https UKserver netmask 255.255.255.255 https interface

    public static tcp (indoor, outdoor) interface ldap UKserver ldap netmask 255.255.255.255

    public static tcp (indoor, outdoor) interface ldaps ldaps netmask 255.255.255.255 UKserver

    public static tcp (indoor, outdoor) interface nntp nntp netmask 255.255.255.255 UKserver

    public static 135 135 UKserver netmask 255.255.255.255 interface tcp (indoor, outdoor)

    public static 102 102 UKserver netmask 255.255.255.255 interface tcp (indoor, outdoor)

    public static 390 390 UKserver netmask 255.255.255.255 interface tcp (indoor, outdoor)

    public static 3268 3268 UKserver netmask 255.255.255.255 interface tcp (indoor, outdoor)

    public static 3269 3269 UKserver netmask 255.255.255.255 interface tcp (indoor, outdoor)

    public static UKserver netmask 255.255.255.255 993 993 interface tcp (indoor, outdoor)

    public static UKserver 995 netmask 255.255.255.255 995 interface tcp (indoor, outdoor)

    public static 563 563 UKserver netmask 255.255.255.255 interface tcp (indoor, outdoor)

    public static 465 465 UKserver netmask 255.255.255.255 interface tcp (indoor, outdoor)

    public static 691 691 UKserver netmask 255.255.255.255 interface tcp (indoor, outdoor)

    public static 6667 UKserver 6667 netmask 255.255.255.255 interface tcp (indoor, outdoor)

    public static 994 994 UKserver netmask 255.255.255.255 interface tcp (indoor, outdoor)

    Access-group Outside_2_Inside in interface outside

    Route outside 0.0.0.0 0.0.0.0 87.224.93.53 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    dynamic-access-policy-registration DfltAccessPolicy

    Ray of AAA-server vpn Protocol

    AAA-server vpn (inside) host UKserver

    key DCSI_vpn_Key07

    the ssh LOCAL console AAA authentication

    Enable http server

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set esp - esp-sha-hmac trans_set

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    Crypto-map dynamic outside_dyn_map 20 transform-set trans_set

    Crypto dynamic-map DYN_MAP 20 the value reverse-road

    address for correspondence outside_map 20 card crypto VPN - USA

    card crypto outside_map 20 peers set othersite2 site1

    card crypto outside_map 20 transform-set trans_set

    map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

    outside_map interface card crypto outside

    crypto isakmp identity address

    crypto ISAKMP allow outside

    crypto ISAKMP policy 10

    preshared authentication

    the Encryption

    sha hash

    Group 2

    lifetime 28800

    crypto ISAKMP policy 20

    preshared authentication

    the Encryption

    md5 hash

    Group 2

    lifetime 28800

    Telnet timeout 5

    SSH timeout 25

    Console timeout 0

    dhcpd dns 8.8.8.8 UKserver

    !

    dhcpd address 172.18.2.100 - 172.18.2.149 inside

    dhcpd allow inside

    !

    dhcpd address 192.168.2.50 - 192.168.2.74 GuestWiFi

    enable GuestWiFi dhcpd

    !

    no basic threat threat detection

    no statistical access list - a threat detection

    no statistical threat detection tcp-interception

    WebVPN

    internal USER_VPN group policy

    USER_VPN group policy attributes

    Protocol-tunnel-VPN IPSec

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list Split_Tunnel_List

    the authentication of the user activation

    tunnel-group othersite2 type ipsec-l2l

    othersite2 group of tunnel ipsec-attributes

    pre-shared-key *.

    type tunnel-group USER_VPN remote access

    attributes global-tunnel-group USER_VPN

    address pool ClientVPN

    Authentication-server group (external vpn)

    Group Policy - by default-USER_VPN

    IPSec-attributes tunnel-group USER_VPN

    pre-shared-key *.

    tunnel-group site1 type ipsec-l2l

    tunnel-group ipsec-attributes site1

    pre-shared-key *.

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect the rsh

    inspect the rtsp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the tftp

    !

    global service-policy global_policy

    context of prompt hostname

    Cryptochecksum:d000c75c8864547dfabaf3652d81be71

    : end





    Hello

    The output seems to say that traffic is indeed transmitted to connect VPN L2L

    Can you PING from hosts on the network 172.18.2.0/24 to the hosts on the network 172.17.2.0/24?

    Have you tried several different target hosts on the network you are trying to ping while might exclude us actual devices are not just meeting the specifications these PINGs?

    -Jouni

  • Cisco VPN Client and 64-Bit OS Support

    I'm in the stages of planning/testing of migrating users to the Cisco VPN client. Problem that I came across well is that I can't find a version that supports 64-bit operating systems. I looked through the Download Center with no luck. I'm a little more looking for a version out there? Thanks in advance.

    As much as I know there is no 64-bit support and is not yet on the roadmap of IPSEC VPN Client. For more details, see:

    http://www.Cisco.com/en/us/docs/security/ASA/compatibility/ASA-VPN-compatibility.html

    Concerning

    Farrukh

Maybe you are looking for

  • How can I delete the browsing history but keep bank account numbers etc.

    My financial institution recommends to delete my browsing history after that I have signed. I can do this without removing the bank account numbers etc. I don't understand the descriptions of cache, cookies, etc.

  • RN316 folder randomly freezing on 6.4.0

    Hello I upgraded a customer RN316 firmware 6.4.0 about 2 days ago. The update of the firmware has successfully reported and everything seemed ok for about half a day.The main part (2.7 TB) of data, has become extremely unstable, randomly freezing for

  • Svchost.exe - application error the instruction at "0x001a61ae" referenced memory at "0x00000000".

    How to fix the svchost.exe application error the instruction at "0x001a61ae" referenced memory at "0x00000000".

  • Eject the CD

    I put a CD of photos in my computer (Qosmio) and it is said Virgin disk but will not be displayed anywhere and I can't understand how something that will not be displayed as an icon on thecomputer eject.  What can I do?

  • Multiple monitors.

    I have problems to connect to an additional monitor.  I bought the adapter to connect the second monitor;  However when I turn on the system I get this error. 'No Signal' on the monitor that I added and it will remain empty. What can be my problem?