IPSec VPN pix 501 no LAN access

Similar Questions

• PAT on IPSEC VPN (Pix 501)

  Hello

  I work to connect a PIX 501 VPN for a 3rd party hub 3015. The hub requires all traffic to come from a single source IP address. This IP address is assigned to me as z.z.z.z. I have successfully built the VPN and tested by mapping staticly internal IP with the IP address assigned, but cannot get the orders right to do with PAT in order to have more than one computer on the subnet 10.x.x.0. This Pix is also a backup for internet routing and NAT work currently as well for this.

  I can redirect traffic to my subnet to the remote subnet via the VPN, but I can't seem to get the right stuff PAT to the VPN using the assigned IP address. If anyone can give me some advice that would be great.

  lines of current config interesting configuration with static mapping:

  --------------------------------------------------------------------------

  access-list 101 permit ip 10.0.0.0 255.255.255.0 y.y.y.0 255.255.255.0

  access-list 102 permit ip y.y.y.0 255.255.255.0 z.z.z.z host

  access-list 103 allow host ip y.y.y.0 255.255.255.0 z.z.z.z

  IP address outside w.w.w.1 255.255.255.248

  IP address inside 10.0.0.1 255.255.255.0

  Global 1 interface (outside)

  NAT (inside) - 0 102 access list

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  public static z.z.z.z (Interior, exterior) 10.x.x.50 netmask 255.255.255.255 0 0

  Route outside 0.0.0.0 0.0.0.0 w.w.w.2 1

  correspondence address card crypto mymap 10 103

  mymap outside crypto map interface

  ISAKMP allows outside

  Thank you!

  Dave

  Dave,

  (1) get rid of static electricity. Use more Global/NAT. The static method will create a permanent

  translation for your guests inside and they will always be this way natted. Use

  NAT of politics, on the contrary, as shown here:

  not static (inside, outside) z.z.z.z 10.x.x.50 netmask 255.255.255.255 0 0

  Global (outside) 2 z.z.z.z netmask 255.255.255.255

  (Inside) NAT 2-list of access 101

  (2) the statement, "nat (inside) access 0 2' list will prevent nat of your valuable traffic."

  Delete this because you need to nat 2 nat/global card. (as a general rule, simply you

  If you terminate VPN clients on your device and do not want inside the traffic which

  is intended for the vpn clients to be natted on the external interface).

  (3) with the instructions of Global/nat 2, all traffic destined for the remote network will be first

  translated into z.z.z.z. Then your card crypto using the ACL 103 will encrypt all traffic which

  sources of z.z.z.z for y.y.y.0 24. This translation wil happen only when traffic is destined for the vpn.

  I hope this helps. I have this work on many tunnels as you describe.

  Jamison

• ASA 5505 IPSec client-to-site any LAN access?

  Hello

  Like many others, I have problems get ipsec vpn clients can communicate with my LAN.

  I have configure ipsec with the wizard, I have also to add an ACL to allow the network to pool for the vpn client to connect to the local network, but with little success.

  Many of the responses I've seen includes changes in the NAT table, I tried a lot of them, but without success.

  There must be something really simple, that it's so frustrating because I guess it is supposed to be a relatively simple thing to get running.

  VPN client (Linux, iptables rules no) get 10.80.80.100 address, but cannot connect to a TCP service on a machine of LAN (no firewall on computer LAN) and can not ping LAN.

  The VPN client routing table:

  Kernel IP routing table
  Destination Gateway Genmask Flags metric Ref use Iface
  85.24.249.35 212.112.31.254 UGH 255.255.255.255 0 0 0 eth0
  10.80.80.0 0.0.0.0 255.255.255.0 U 0 0 0 tun0
  212.112.31.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
  0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 tun0

  : Saved
  
  :
  
  ASA Version 7.2(4)
  
  !
  
  hostname ciscoasa
  
  domain-name default.domain.invalid
  
  enable password xxx encrypted
  
  passwd xxx encrypted
  
  names
  
  !
  
  interface Vlan1
  
  nameif inside
  
  security-level 100
  
  ip address 192.168.0.1 255.255.255.0
  
  !
  
  interface Vlan2
  
  nameif outside
  
  security-level 0
  
  ip address dhcp setroute
  
  !
  
  interface Ethernet0/0
  
  switchport access vlan 2
  
  !
  
  interface Ethernet0/1
  
  !
  
  interface Ethernet0/2
  
  !
  
  interface Ethernet0/3
  
  !
  
  interface Ethernet0/4
  
  !
  
  interface Ethernet0/5
  
  !
  
  interface Ethernet0/6
  
  !
  
  interface Ethernet0/7
  
  !
  
  ftp mode passive
  
  dns server-group DefaultDNS
  
  domain-name default.domain.invalid
  
  same-security-traffic permit inter-interface
  
  access-list tictac_splitTunnelAcl remark allow vpn tunnel users to LAN
  
  access-list tictac_splitTunnelAcl standard permit 192.168.0.0 255.255.255.0
  
  access-list inside_nat0_outbound extended permit ip any 10.80.80.0 255.255.255.0
  
  access-list inside_access_in extended permit ip any any log disable
  
  access-list outside_access_out extended permit ip any any
  
  pager lines 24
  
  logging enable
  
  logging asdm informational
  
  mtu outside 1500
  
  mtu inside 1500
  
  ip local pool vpnpool 10.80.80.100-10.80.80.120 mask 255.255.255.0
  
  icmp unreachable rate-limit 1 burst-size 1
  
  asdm image disk0:/asdm-524.bin
  
  no asdm history enable
  
  arp timeout 14400
  
  global (outside) 1 interface
  
  nat (inside) 0 access-list inside_nat0_outbound
  
  nat (inside) 1 0.0.0.0 0.0.0.0
  
  access-group outside_access_out out interface outside
  
  access-group inside_access_in in interface inside
  
  timeout xlate 3:00:00
  
  timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  
  timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
  
  timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
  
  timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  
  http server enable
  
  http 192.168.0.0 255.255.255.0 inside
  
  no snmp-server location
  
  no snmp-server contact
  
  snmp-server enable traps snmp authentication linkup linkdown coldstart
  
  crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
  
  crypto dynamic-map outside_dyn_map 20 set pfs group1
  
  crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
  
  crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
  
  crypto map outside_map interface outside
  
  crypto isakmp enable outside
  
  crypto isakmp policy 10
  
  authentication pre-share
  
  encryption 3des
  
  hash sha
  
  group 2
  
  lifetime 86400
  
  telnet 192.168.0.0 255.255.255.0 inside
  
  telnet timeout 5
  
  ssh timeout 5
  
  console timeout 0
  
  dhcpd auto_config outside
  
  !
  
  dhcpd address 192.168.0.2-192.168.0.33 inside
  
  dhcpd dns 8.8.8.8 4.2.2.2 interface inside
  
  dhcpd enable inside
  
  !
  
  group-policy tictac internal
  
  group-policy tictac attributes
  
  dns-server value 8.8.8.8 4.2.2.2
  
  vpn-tunnel-protocol IPSec
  
  split-tunnel-policy tunnelspecified
  
  split-tunnel-network-list none
  
  username mattiasb password SVCZv/HMkykG.ikA encrypted privilege 0
  
  username mattiasb attributes
  
  vpn-group-policy tictac
  
  tunnel-group tictac type ipsec-ra
  
  tunnel-group tictac general-attributes
  
  address-pool vpnpool
  
  default-group-policy tictac
  
  tunnel-group tictac ipsec-attributes
  
  pre-shared-key *
  
  !
  
  class-map inspection_default
  
  match default-inspection-traffic
  
  !
  
  !
  
  policy-map type inspect dns preset_dns_map
  
  parameters
  
    message-length maximum 512
  
  policy-map global_policy
  
  class inspection_default
  
    inspect dns preset_dns_map
  
    inspect ftp
  
    inspect h323 h225
  
    inspect h323 ras
  
    inspect rsh
  
    inspect rtsp
  
    inspect esmtp
  
    inspect sqlnet
  
    inspect skinny
  
    inspect sunrpc
  
    inspect xdmcp
  
    inspect sip
  
    inspect netbios
  
    inspect tftp
  
  !
  
  service-policy global_policy global
  
  prompt hostname context
  
  Cryptochecksum:6e456ab21d08182ca41ed0f1be031797
  
  : end
  
  asdm image disk0:/asdm-524.bin
  
  no asdm history enable
  
  

  The list of split tunnel network was put on 'none' in your configuration:

  group-policy tictac attributes
  
  dns-server value 8.8.8.8 4.2.2.2
  
  vpn-tunnel-protocol IPSec
  
  split-tunnel-policy tunnelspecified
  
  split-tunnel-network-list none
  
  
  Please configure the tunnel list to reference the split tunnel ACL as follows:
  
  group-policy tictac attributes
  
     split-tunnel-network-list value tictac_splitTunnelAcl

  Hope that helps.

• Reseting ipsec on PIX 501

  Hi all. Just a quick question. I can't seem to find how to reset ipsec on PIX 501 and force her to negotiate again and I also want to reset statistics for ipsec his. I know that I saw somewhere, orders, but now can't seem to find the commands from anywhere.

  Thanks in advance for any help.

  Hello...

  Config mode...

  ISAKMP crypto claire his

  - and -

  clear crypto ipsec his

  PS. You can find the commands on the PIX by entering the configuration mode by typing...

  PIX01 (config) # clear cry?

  Hope the above helps and please note messages!

• Help with vpn pix 501

  I'm setting up a cisco pix 501 vpn tunnel but will have questions. The Firewall works although I am able to get out of the internet, but the VPN does not work. On the primary side, I see that the tunnel is up and the traffic is sent but not received.

  Currently I'm sitting at the secondary location but don't know what the problem maybe. Anyone know what I have wrong which could prevent the data to send from this device?

  Here is my config

  Here's my config if it would help

  See the race
  : Saved
  :
  6.3 (5) PIX version
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 2KFQnbNIdI.2KYOU encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  hostname ciscofirewall
  domain hillsanddales.com
  fixup protocol dns-length maximum 512
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol rsh 514
  fixup protocol rtsp 5
  fixup protocol rtsp 55
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25

  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list 101 permit ip 192.168.80.0 255.255.255.0 192.168.50.0 255.255.255.0
  192.168.80.0 IP Access-list sheep 255.255.255.0 allow 192.168.50.0 255.255.255.0
  in_outside list access permit tcp any host 192.168.50.240
  in_outside list access permit tcp any host 64.90.xxx.xx
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  IP address outside 66.84.xxx.xx 255.255.255.252
  IP address inside 192.168.80.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  location of PDM 192.168.50.0 255.255.255.0 outside
  location of PDM 192.168.80.2 255.255.255.255 inside
  location of PDM 192.168.50.0 255.255.255.0 inside
  location of PDM 182.168.80.0 255.255.255.255 inside
  location of PDM 0.0.0.0 255.255.255.0 inside
  location of PDM 0.0.0.0 255.255.255.255 inside
  location of PDM 192.168.80.5 255.255.255.255 inside
  location of PDM 192.168.80.7 255.255.255.255 inside
  PDM logging 100 information
  history of PDM activate

  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Route outside 0.0.0.0 0.0.0.0 66.84.xxx.x
  Route inside 192.168.50.0 255.255.255.0 192.168.50.240 1
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + 3 max-failed-attempts
  AAA-server GANYMEDE + deadtime 10
  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS 3 max-failed-attempts
  AAA-RADIUS deadtime 10 Server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.80.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  <--- more="" ---="">

  Permitted connection ipsec sysopt
  Crypto ipsec transform-set esp-3des esp-md5-hmac aptset
  aptmap 10 ipsec-isakmp crypto map
  correspondence address card crypto aptmap 10 101
  card crypto aptmap 10 peers set 64.90.xxx.xx
  card crypto aptmap 10 transform-set aptset
  aptmap interface card crypto outside
  ISAKMP allows outside
  ISAKMP key * address 64.90.xxx.xx netmask 255.255.255.255
  ISAKMP identity address
  ISAKMP nat-traversal 20
  part of pre authentication ISAKMP policy 10
  ISAKMP policy 10 3des encryption
  ISAKMP policy 10 md5 hash
  10 2 ISAKMP policy group
  ISAKMP life duration strategy 10 86400
  Telnet 192.168.80.2 255.255.255.255 inside
  Telnet 182.168.80.0 255.255.255.255 inside
  Telnet 192.168.80.5 255.255.255.255 inside
  Telnet 192.168.80.0 255.255.255.0 inside
  Telnet 192.168.80.7 255.255.255.255 inside
  Telnet timeout 5
  SSH timeout 5
  management-access inside

  Console timeout 0
  dhcpd address 192.168.80.2 - 192.168.80.33 inside
  dhcpd dns 64.90.xxx.xx 64.90.xxx.xx
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  dhcpd allow inside
  Terminal width 80
  Cryptochecksum:01532689fac9491fae8f86e91e2bd4c0
  : end

  Hello

  At least the NAT0 ACL is not in use

  You should have this added to the configuration

  NAT (inside) 0 access-list sheep

  -Jouni

• PPTP VPN pix 501 question

  I'm relatively new to the security stuff.  I'm a guy of the voice.  I created a Pix 501 for IPSEC VPN and works very well.  Then I tried it setting up PPTP VPN.  I use Windows XP to connect.  It connects fine, but I can't ping to the inside interface on the PIX.  I can do this by using IPSEC.  Any ideas?   Here is my config:

  :

  6.3 (3) version PIX

  interface ethernet0 car

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the password * encrypted

  passwd * encrypted

  host name *.

  domain name *.

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol pptp 1723

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  access-list 101 permit icmp any any echo response

  access-list 80 allow ip 10.0.0.0 255.255.255.0 192.168.5.0 255.255.255.0

  access-list ip 10.0.0.0 sheep allow 255.255.255.0 192.168.5.0 255.255.255.0

  access-list ip 10.0.0.0 sheep allow 255.255.255.0 192.168.6.0 255.255.255.0

  pager lines 24

  opening of session

  emergency logging console

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside of *. *. *. * 255.255.255.0

  IP address inside 10.0.0.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool pool1 192.168.5.100 - 192.168.5.200

  IP local pool pool2 192.168.6.100 - 192.168.6.200

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 10.0.0.0 255.0.0.0 0 0

  Access-group 101 in external interface

  Route outside 0.0.0.0 0.0.0.0 *. *. *. * 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  the ssh LOCAL console AAA authentication

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Sysopt connection permit-pptp

  Sysopt connection permit-l2tp

  Crypto ipsec transform-set high - esp-3des esp-sha-hmac

  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

  Crypto dynamic-map cisco 4 strong transform-set - a

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  Cisco dynamic of the partners-card 20 crypto ipsec isakmp

  partner-map interface card crypto outside

  card crypto 10 PPTP ipsec-isakmp dynamic dynmap

  ISAKMP allows outside

  ISAKMP key * address 0.0.0.0 netmask 0.0.0.0

  ISAKMP nat-traversal 20

  part of pre authentication ISAKMP policy 8

  ISAKMP strategy 8 3des encryption

  ISAKMP strategy 8 md5 hash

  8 2 ISAKMP policy group

  ISAKMP life duration strategy 8 the 86400

  vpngroup address pool1 pool test

  vpngroup default-field lab118 test

  vpngroup split tunnel 80 test

  vpngroup test 1800 idle time

  Telnet timeout 5

  SSH 10.0.0.0 255.0.0.0 inside

  SSH 192.168.5.0 255.255.255.0 inside

  SSH 192.168.6.0 255.255.255.0 inside

  SSH timeout 5

  management-access inside

  Console timeout 0

  VPDN PPTP-VPDN-group accept dialin pptp

  VPDN group PPTP-VPDN-GROUP ppp authentication chap

  VPDN group PPTP-VPDN-GROUP ppp mschap authentication

  VPDN group PPTP-VPDN-GROUP ppp encryption mppe auto

  VPDN group VPDN GROUP-PPTP client configuration address local pool2

  VPDN group VPDN GROUP-PPTP client configuration dns 8.8.8.8

  VPDN group VPDN GROUP-PPTP pptp echo 60

  VPDN group VPDN GROUP-PPTP client for local authentication

  VPDN username bmeade password *.

  VPDN allow outside

  You will have to connect to an internal system inside and out run the PIX using pptp.

  For ssh access the PIX, you will also need additional configuration, see the section on code PIX pre 7.x, section access ssh to the security apparatus .

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a008069bf1b.shtml#C4

  Concerning

• PIX 501 to allow access to the ftp server

  Hello

  We have a public ip address of the pix 501 and the other, I want to access the ftp server on the internal network from the outside. I tried to configure the PDM by a static nat, which translate to the address of the FTP to the public address, but then none of the stations networks could out - how can I configure it?

  I would also like to know what ports should I open on the acl for access to the ftp server.

  Thank you, daguech

  Yes, sorry... You must use the unique host for addresses command. The access list is applied to your external interface?

  for example, the command would be:

  Access-group acl_out in interface outside

  Also, can you connect to the local ftp server behind a firewall?

• L2L pix 501 and remote access VPN

  Hi, I'm working on an old 501 PIX w / Software 6.3 (5), he already have access to remote VPN configuration and works very well, but now he needs a L2L implemented. One thing I try to do all the work remotely via VPN or ssh to the machine. I don't know what's on the other end, but they swear that it is set up and maybe my problem is when I start putting in orders for the other VPN it breaks the remote VPN access. One thing that I have to do is NAT a host on the inside to appear as another host on the end. I use these commands and I think it works cannot be said.

  access-list 101 permit ip remote_network 255.255.255.0 local_server host

  public static 10.1.0.203 (inside, outside) - access list 101

  then

  access-list 102 permit ip host 10.1.0.203 192.168.50.83
  access-list 102 permit ip host 10.1.0.203 192.168.50.86
  access-list 102 permit ip host 10.1.0.203 192.168.50.50
  access-list 102 permit ip host 10.1.0.203 192.168.50.85

  and use it to match against

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  EMDs-map 10 ipsec-isakmp crypto map
  correspondence address card crypto emds-map 10 102
  card crypto emds-map 10 peers set remote_vpn_server
  card crypto emds-card 10 set of transformation-ESP-3DES-SHA

  then

  ISAKMP key magic_key address remote_vpn_server netmask 255.255.255.255
  ISAKMP identity hostname
  part of pre authentication ISAKMP policy 10
  ISAKMP policy 10 3des encryption
  ISAKMP policy 10 sha hash
  10 1 ISAKMP policy group
  ISAKMP life duration strategy 10 86400

  and that is where it usually breaks the VPN, I don't know if the other VPN works due to not being not able to get to this server to try to ping, I don't really like to try this stuff remotely but I don't have a lot of choice at the moment.

  Any thoughts?

  Thank you

  Jarrid Graham

  Yes, just use the number of different sequence with 1 name of the crypto map. Please also ensure that your dynamic crypto map, which is your vpn client has the sequence down the crypto map (more), because you want to make sure that the static crypto map (for lan-to-lan tunnel has higher sequence number (lower number)).

  The political isakmp sequence number does not match, it is processed from top to bottom (number less than the high number) and also long 1 set of isakmp policy corresponds to the remote peer, it will be negotiated properly.

  Hope that answers your question and please note useful post. Thank you.

• PIX 501 and pcAnywhere access rules

  Hello

  I'm having a problem with the implementation of pcANywhere remote access Access 2 servers on the inside network. I created 2 static rules and access lists 2 to start, but I can't get thru to the server. These are the settings

  static (inside, outside) 7x.x.x.x 5631 172.16.x.x tcp 5631 255.255.255.255

  static (inside, outside) udp 7x.x.x.x 172.16.x.x 5632 5632 255.255.255.255

  list of allowed inbound tcp access any host 172.16.x.x eq 5631

  list of allowed inbound udp access any host 172.16.x.x eq 5632

  Access-group interface incoming outside

  Version 6.3 of the PIX using

  I also tried access server list terminal server because another method of access, but not go either.

  There are no other rules.

  Any ideas why this would not work?

  TIA

  Vince

  your external ACL must mention the public IP address of your server:

  list of allowed inbound tcp access any host 7x.x.x.x eq 5631

  list of allowed inbound udp access any host 7x.x.x.x eq 5632

• PIX &amp; lt; -&gt; user policies VPN PIX and the Windows domain controller

  I've set up a star using IPsec VPN PIX network, all IP traffic is allowed to pass through.

  At the Center, there is a Windows 2003 Small Business Server.

  On remote sites, there is only Windows XP clients used by employees working remotely in the central office.

  Initially, I had a problem of authentication on the server, but I found a document suggesting the Kerberos setting to go to TCP instead of UDP and it solved this issue.

  Now, there is one problem remaining, I can authenticate and access the server resources such as file shares, I can connect to the server Exchange etc. But the client computers do not receive from the server group policies. The error message I am getting in Event Viewer Windows is Userenv id: 1054 - Microsoft suggestion is to check if the DNS works and works DNS, I can locate the DC etc. without problem.

  I tried to make LDAP queries on the server, and again, it works without problem.

  The NetBIOS resolution works very well.

  Basically, everything seems to work expect to get group strategies.

  Does anyone have any suggestions where I should look planned for the solution to this problem?

  Kind regards

  Flovin Olsen

  Here is a vbscript script you must run on every PC has the problem.

  -Cross-section below-

  Dim wshShell

  Set wshShell = WScript.CreateObject ("WScript.Shell")

  prefix = "HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\System\."

  prefix wshShell.regWrite & "GroupPolicyMinTransferRate", 0, "REG_DWORD"

  Prefix2 = "HKEY_CURRENT_USER\Software\Policies\Microsoft\Windows\System\."

  wshShell.regWrite prefix2 & "GroupPolicyMinTransferRate", 0, "REG_DWORD"

  MsgBox "done."

  ---------stop cut -----------------

  Hope this helps

• VPN site-to-site between two PIX 501 with Client VPN access

  Site A and site B are connected with VPN Site to Site between two PIX 501.

  Also, site A is configured for remote access VPN client. If a remote client connects to Site A, it can only get access to the LAN of Site A, it cannot access anything whatsoever behind PIX on Site B.

  How is that possible for a VPN client connected to Site A to Site B?

  Thank you very much.

  Alex

  Bad and worse news:

  Bad: Not running the 7.0 series PIX cannot route traffic on the same interface, the traffic is recived. Version 7.0 solves this ipsec traffic.

  Even worse: PIX 501 can not be upgraded to 7.0...

  A couple of things to think about would be the upgrade to hardware that can run the new IOS or allowing a VPN R.A. on site B.

  HTH Please assess whether this is the case.

  Thank you

• L2l IPSec VPN 3000 and PIX 501

  Hello

  I have a remote site that has a broadband internet connection and uses a PIX 501.  We wanted to connect them with our main office using our VPN 3000 via VPN site-to-site.

  I followed the following documentation:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml#tshoot

  However the L2L session does not appear on the hub when I check the active sessions.

  The network diagram, as well as the PIX config and the screenshots of the VPN configuration for the IPSec-L2L tunnel is attached.

  Any help or advice are appreciated.

  I just noticed that the PIX firewall, the phase 1 paramateres are not configured. You must configure the same PASE 1 and phase 2 settings on both ends of the tunnel.

  For example, on CVPN 3000, you have configured settings Phase 1 as 3DES, pre-shared key etc... We have the same configuration on the PIX firewall too.

  Here is an example of sample config

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml

  I hope this helps!

• PIX 501 and VPN Linksys router (WRV200)

  I inherited a work where we have a Cisco PIX 501 firewall to a single site and Linksys WRV200 Router VPN on two other

  sites. Asked me to connect these routers Linksys firewall PIX via the VPN.

  According to me, the Linksys vpn routers can only connect via IPSec VPN, I'm looking for help on the configuration of the PIX 501 for the linksys to connect with the following, if possible.

  Key exchange method: Auto (IKE)

  Encryption: Auto, 3DES, AES128, AES192, AES256

  Authentication: MD5

  Pre Shared Key: xxx

  PFS: Enabled

  Life ISAKMP key: 28800

  Life of key IPSec: 3600

  The pix, I installed MDP and I tried to use the VPN wizard without result.

  I chose the following settings when you make the VPN Wizard:

  Type of VPN: remote VPN access

  Interface: outside

  Type of Client VPN device used: Cisco VPN Client

  (can choose customer of Cisco VPN 3000, MS Windows Client by using the client MS Windows using L2TP, PPTP)

  VPN clients group

  Name of Group: RabyEstates

  Pre Shared Key: rabytest

  Scope of the Client authentication: disabled

  Address pool

  Name of the cluster: VPN - LAN

  Starter course: 192.168.2.200

  End of row: 192.168.2.250

  Domain DNS/WINS/by default: no

  IKE policy

  Encryption: 3DES

  Authentication: MD5

  Diffie-Hellman group: Group 2 (1024 bits)

  Transform set

  Encryption: 3DES

  Authentication: MD5

  I have attached the log of the VPN Linksys router VPN.

  This is the first time that I have ever worked with PIX so I'm still trying to figure the thing to, but I'm confident with the CCNA level network.

  Thanks for your help!

  Hello

  Everything looks fine for me, try to have a computer in every network and ping between them. Check the newspapers/debug and fix them.

  Let me know.

  See you soon,.

  Daniel

• VPN connects but no remote LAN access

  Hello

  I'll put up on a PIX 501 VPN remote access.

  When I try to connect via VPN software, I am able to connect but I am unable to access LAN resources.

  I have pasted below part of which seems relevant to my setup. I'm stuck on this issue, could someone help me? Thanks in advance.

  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  test.local domain name
  name 10.0.2.0 inside
  name 10.0.2.13 MSExchange-en
  2.2.2.2 the MSExchange-out name

  outside_access_in tcp allowed access list all gt 1023 host 2.2.2.2 eq smtp
  outside_access_in list access permit tcp any host 2.2.2.2 eq https
  outside_access_in list access permit tcp any host 2.2.2.2 eq www
  inside_outbound_nat0_acl 10.0.2.0 ip access list allow 255.255.255.0 192.168.235.0 255.255.255.192
  access-list 101 permit icmp any one

  3.3.3.3 exterior IP address 255.255.255.0
  IP address inside 10.0.2.254 255.255.255.0
  IP local pool vpn_pool 192.168.235.1 - 192.168.235.15
  IP local pool vpn_pool_2 192.168.235.16 - 192.168.235.40

  1 3.3.3.4 (outside) global
  NAT (inside) 0-list of access inside_outbound_nat0_acl
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  static (inside, outside) 2.2.2.2 10.0.2.13 netmask 255.255.255.255 1000 1000
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 3.3.3.1 1

  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS (inside) host 10.0.2.3 * timeout 10
  AAA-server local LOCAL Protocol

  Permitted connection ipsec sysopt
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto-map dynamic dynmap 10 game of transformation-ESP-3DES-MD5
  map outside_map 90-isakmp ipsec crypto dynamic dynmap
  card crypto outside_map the LOCAL RADIUS client authentication
  outside_map interface card crypto outside
  ISAKMP allows outside
  part of pre authentication ISAKMP policy 20
  ISAKMP policy 20 3des encryption
  ISAKMP policy 20 md5 hash
  20 2 ISAKMP policy group
  ISAKMP duration strategy of life 20 86400
  vpngroup signal address vpn_pool pool
  vpngroup dns-server 10.0.2.3 signal
  vpngroup default-field test.local signal
  vpngroup idle time 1800 signal
  vpngroup max-time 14400 signal
  signal vpngroup password *.
  vpngroup TF vpn_pool_2 address pool
  vpngroup dns-server 10.0.2.3 TF
  TF vpngroup default-domain test.local
  vpngroup TF 1800 idle time
  vpngroup max-time 14400 TF
  TF vpngroup password *.

  Kind regards

  Joana

  Very similar to the question of the configuration of the switch. You should check if there is no specific roads on the switch outside the default gateway. The switch should route the subnet pool ip to the firewall (10.0.2.254).

• PIX 501 for Cisco 3640 VPN router

  -Start ciscomoderator note - the following message has been changed to remove potentially sensitive information. Please refrain from publishing confidential information about the site to reduce the risk to the security of your network. -end of the note ciscomoderator-

  Have a 501 PIX and Cisco 3640 router. The 3640 is configured for dynamic map for VPN. The PIX 501 is set to pointing to the 3640 router static map. I can establish a tunnel linking the PIX to the router and telnet to a machine AIX on the inside network to the router. When I try to print on the network of the PIX 501 inside it fails.

  What Miss me? I added the configuration for the PIX and the router.

  Here are the PIX config:

  PIX Version 6.1 (1)

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable encrypted password xxxxxxxxxxxxxxxx

  xxxxxxxxxxxxx encrypted passwd

  pixfirewall hostname

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 1720

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  names of

  pager lines 24

  interface ethernet0 10baset

  interface ethernet1 10full

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside dhcp setroute

  IP address inside 192.168.1.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  No sysopt route dnat

  Telnet timeout 5

  SSH timeout 5

  dhcpd address 192.168.1.2 - 192.168.1.33 inside

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:XXXXXXXXXXXXXXXXXXX

  : end

  Here is the router config

  Router #sh runn

  Building configuration...

  Current configuration: 6500 bytes

  !

  version 12.2

  no service button

  tcp KeepAlive-component snap-in service

  a tcp-KeepAlive-quick service

  horodateurs service debug datetime localtime

  Log service timestamps datetime localtime

  no password encryption service

  !

  router host name

  !

  start the flash slot1:c3640 - ik9o3s - mz.122 - 16.bin system

  queue logging limit 100

  activate the password xxxxxxxxxxxxxxxxx

  !

  clock TimeZone Central - 6

  clock summer-time recurring CENTRAL

  IP subnet zero

  no ip source route

  !

  !

  no ip domain-lookup

  !

  no ip bootp Server

  inspect the name smtp Internet IP

  inspect the name Internet ftp IP

  inspect the name Internet tftp IP

  inspect the IP udp Internet name

  inspect the tcp IP Internet name

  inspect the name DMZ smtp IP

  inspect the name ftp DMZ IP

  inspect the name DMZ tftp IP

  inspect the name DMZ udp IP

  inspect the name DMZ tcp IP

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 20

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key address x.x.180.133 xxxxxxxxxxx

  ISAKMP crypto keys xxxxxxxxxxx address 0.0.0.0 0.0.0.0

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac vpn test

  Crypto ipsec transform-set esp-3des esp-sha-hmac PIXRMT

  !

  dynamic-map crypto dny - Sai 25

  game of transformation-PIXRMT

  match static address PIX1

  !

  !

  static-card 10 map ipsec-isakmp crypto

  the value of x.x.180.133 peer

  the transform-set vpn-test value

  match static address of Hunt

  !

  map ISCMAP 15-isakmp ipsec crypto dynamic dny - isc

  !

  call the rsvp-sync

  !

  !

  !

  controller T1 0/0

  framing ESF

  linecode b8zs

  Slots 1-12 channels-group 0 64 speed

  Description controller to the remote frame relay

  !

  controller T1 0/1

  framing ESF

  linecode b8zs

  Timeslots 1-24 of channel-group 0 64 speed

  Description controller for internet link SBIS

  !

  interface Serial0/0:0

  Description CKT ID 14.HXGK.785129 Frame Relay to Remote Sites

  bandwidth 768

  no ip address

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  encapsulation frame-relay

  frame-relay lmi-type ansi

  !

  interface Serial0 / point to point 0:0.17

  Description Frame Relay to xxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 17 frame relay interface

  !

  interface Serial0 / point to point 0:0.18

  Description Frame Relay to xxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 18 frame relay interface

  !

  interface Serial0 / point to point 0:0.19

  Description Frame Relay to xxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 19 frame relay interface

  !

  interface Serial0 / point to point 0:0.20

  Description Frame Relay to xxxxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 20 frame relay interface

  !

  interface Serial0 / point to point 0:0.21

  Description Frame Relay to xxxxxxxxxxxx

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 21 frame relay interface

  !

  interface Serial0 / point to point 0:0.101

  Description Frame Relay to xxxxxxxxxxx

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 101 frame relay interface

  !

  interface Serial0/1:0

  CKT ID 14.HCGS.785383 T1 to ITT description

  bandwidth 1536

  IP address x.x.76.14 255.255.255.252

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  NAT outside IP

  inspect the Internet IP on

  no ip route cache

  card crypto ISCMAP

  !

  interface Ethernet1/0

  IP 10.1.1.1 255.255.0.0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  no ip route cache

  no ip mroute-cache

  Half duplex

  !

  interface Ethernet2/0

  IP 10.100.1.1 255.255.0.0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  no ip route cache

  no ip mroute-cache

  Half duplex

  !

  router RIP

  10.0.0.0 network

  network 192.168.1.0

  !

  IP nat inside source list 112 interface Serial0/1: 0 overload

  IP nat inside source static tcp 10.1.3.4 443 209.184.71.138 443 extensible

  IP nat inside source static tcp 10.1.3.4 9869 209.184.71.138 9869 extensible

  IP nat inside source 10.1.3.2 static 209.184.71.140

  IP nat inside source static 10.1.3.6 209.184.71.139

  IP nat inside source static 10.1.3.8 209.184.71.136

  IP nat inside source static tcp 10.1.3.10 80 209.184.71.137 80 extensible

  IP classless

  IP route 0.0.0.0 0.0.0.0 x.x.76.13

  IP route 10.2.0.0 255.255.0.0 Serial0 / 0:0.19

  IP route 10.3.0.0 255.255.0.0 Serial0 / 0:0.18

  IP route 10.4.0.0 255.255.0.0 Serial0 / 0:0.17

  IP route 10.5.0.0 255.255.0.0 Serial0 / 0:0.20

  IP route 10.6.0.0 255.255.0.0 Serial0 / 0:0.21

  IP route 10.7.0.0 255.255.0.0 Serial0 / 0:0.101

  no ip address of the http server

  !

  !

  PIX1 static extended IP access list

  IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255

  IP access-list extended hunting-static

  IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255

  extended IP access vpn-static list

  ip permit 192.168.1.0 0.0.0.255 10.1.0.0 0.0.255.255

  IP 192.0.0.0 allow 0.255.255.255 10.1.0.0 0.0.255.255

  access-list 1 refuse 10.0.0.0 0.255.255.255

  access-list 1 permit one

  access-list 12 refuse 10.1.3.2

  access-list 12 allow 10.1.0.0 0.0.255.255

  access-list 12 allow 10.2.0.0 0.0.255.255

  access-list 12 allow 10.3.0.0 0.0.255.255

  access-list 12 allow 10.4.0.0 0.0.255.255

  access-list 12 allow 10.5.0.0 0.0.255.255

  access-list 12 allow 10.6.0.0 0.0.255.255

  access-list 12 allow 10.7.0.0 0.0.255.255

  access-list 112 deny ip host 10.1.3.2 everything

  access-list 112 refuse ip 10.1.0.0 0.0.255.255 192.168.1.0 0.0.0.255

  access-list 112 allow ip 10.1.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.2.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.3.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.4.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.5.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.6.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.7.0.0 0.0.255.255 everything

  access-list 120 allow ip host 10.100.1.10 10.1.3.7

  not run cdp

  !

  Dial-peer cor custom

  !

  !

  !

  !

  connection of the banner ^ CCC

  ******************************************************************

  WARNING - Unauthorized USE strictly PROHIBITED!

  ******************************************************************

  ^ C

  !

  Line con 0

  line to 0

  password xxxxxxxxxxxx

  local connection

  Modem InOut

  StopBits 1

  FlowControl hardware

  line vty 0 4

  exec-timeout 15 0

  password xxxxxxxxxxxxxx

  opening of session

  !

  end

  Router #.

  Add the following to the PIX:

  > permitted connection ipsec sysopt

  This indicates the PIX around all ACLs for IPsec traffic. Now that your IPSec traffic is still subject to the standard rules of PIX, so launched inside the traffic is allowed to go in, but off-initiated traffic is not.