IPv6, dhcp with a standalone server

Similar Questions

• Difference between Standalone Converter and converter integrated with VMware vCenter Server?

  What is the difference between Standalone Converter and converter integrated with VMware vCenter Server, except that it comes integrated with Vcenter and another does not?
  Please confirm is there the technical differences between them?

  Also take a look at the Release Notes for vCenter Server 4.1.

  of http://www.vmware.com/support/vsphere4/doc/vsp_esx41_vc41_rel_notes.html

  VMware vCenter Converter plugin. VMware vSphere 4.1 and later versions of the update and patch are the latest editions of the VMware vCenter Converter plugin for vSphere Client. VMware will continue to update and support the free Converter Standalone product, which allows conversions from sources such as physical machines, machine formats virtual VMware and Microsoft and some third-party disk image formats.

  André

• Implementation of IPSec Port Forwarding on a Windows 2012 with a LRT224 Server

  Hi all I hope someone can help me validate my troubleshooting. I'm deploying a Server Windows 2012 that will server as a server vpn for customers. In place is a LRT224 with 4 VLANS set up. I have enabled port forwarding for IPSec (UDP/500), L2TP (UDP/1701) and L2TP (UDP/4500) to go on the server.

  In my Initial test, I put the LRT224 on the same network as the client of my test and realized the Test Client (10 Windows) to try to connect to the WAN of the LRT224 interface. I get this message:

  

  Thinking it could be the configuration of the server, I then put the client system on the same vlan on the LRT224 server. When I tried to connect to it directly by using the IP address of the server as a destination, he succeeded.  It is leading me to believe that it is the LRT224.

  I confirmed that VPN passthrough is enabled.

  The firmware version is by: v1.0.5.03 (February 22, 2016 10:12:17)

  Currently, the firewall is disabled (I would activate once I'm working)

  If anyone has ideas or notice a fault in my tests, I would really appreciate the feedback.

  If additional information would be useful, please let me know what you want and I can work for it.

  Thanks to all in advance.

  FreeFallFour wrote:

  I then put the client system on the same vlan on the LRT224 server. When I tried to connect to it directly by using the IP address of the server as a destination, he succeeded.  It is leading me to believe that it is the LRT224.

  It does normally not as I KNOW because the VPN in an outside in the process. You should test the VPN connection outside the server's IP subnet.

  You have the server configuration that the DNS server in the router to DHCP with DNS Proxy is disabled?

  Are you doing load balancing Internet connection?

• Windows cannot communicate with primary dns server

  Hey everybody.  I have a home network, wired PC, 1 wifi 1.  WiFi works fine.  wired network printers work well, other computers (laptops work fine both wired and wireless.)  I have a PC (VISTA), which now gives me the "windows cannot communicate with primary dns server.  This has happened a couple of times, but a reboot fixed things.  Once I had to change primary dns server from automatic to 208.67.222.222 (who got to this site), it worked.  Now, the same error, but nothing works.  I have tried in both directions between the DNS auto numbers listed here, also, have tried the following:

  ipconfig/flushdns
  ipconfig/registerdns
  netsh interface ip reset reset.log
  netsh int ip reset resetlog.txt

  and had windows try to reset the DNS of countless times.  Nothing works.  The upgrade to W7 eventually will correct this problem?  Another question, my wife insists on the use of AOL software (I know, I know), even if all that she uses to is by e-mail.  She says she loves interface.  A chance that caused this problem?

  Hello

  1. have there been recent changes to the system before the show?

  2. the problem occurs only with specific applications?

  Method 1:

  Follow the link and follow the steps proposed by Shekhar S and check if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/cant-communicate-with-primary-DNS-server/9043f785-2f4e-4CC1-ADF5-6ba5ca413749

  Method 2:

  Follow the link below and follow the steps. Check if it helps.

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers

  http://support.Microsoft.com/kb/928233

  I also suggest you to run the command in the command prompt and check where the Windows Vista computer is pointing to DNS and DHCP.

  ipconfig/all

  Post back with the results in this thread.

  Let us know if it helps.

• When you use network troubleshooting in Windows, get message Windows cannot communicate with primary dns server

  Original Title2: Windows 7 - Internet
   
   
  Original title: can someone help me?
  I use a PC at home with Windows 7.  Whenever the failure at home, I have problems connecting to the Internet. Whenever I try to go on Youtube or another website, I get "Internet Explorer can not display the webpage." Now, my internet and router are configured correctly, then why is what is happening? I ran Diagnostics and got the "Windows cannot communicate with primary DNS server." I tried to reset the TCP/IP settings. It did not work and I did three times! I tried to check the properties of my network when I went to diagnose the problem, he threw some stuff on the property sheets open and close before you reopen the properties. If someone could give a foolproof solution for this annoying internet problem I would really appreciate it. Thank you.

  Hello

  Welcome to the Microsoft community!

  While using the network troubleshooter utility in Windows, you get message that Windows cannot communicate with primary DNS server.

  What is the exact message that you get when you try to check the settings of network domestic?

  I suggest you to change network settings:

  Step 1: change network settings of the router

  a. connect to your router (by typing 192.168.0.1 or 192.168.1.1 in the address bar) and connect. Check your user manual or documentation if you don't know the references of logon.
  b. make sure you are in Setup-> basic configuration category.
  c. scroll down until you see "DHCP Server" - if it is disabled, select 'enable '.
  d. enable DHCP if you want, you can change the number that starts the DHCP IP assigning. (This is optional)
  e. use the DNS servers provided by your ISP. There are many DNS servers out there. It is preferable to use your ISP if possible.
  f. scroll down and click 'Save Settings'.

  Note: The procedure may slightly vary with different routers. You can see the manual or contact ISP for assistance.

  Step 2: change in the computer network settings

  a. click on start and then Control Panel.
  b. go to the networking and sharing Center and then click on change adapter settings.
  c. right-click on connection to the Local network and select Properties.
  d. Select Internet Protocol Version 6, and then click Properties.
  e. Select obtain DNS server automatically an address and press Ok.
  f. Select obtain IP address automatically.
  g. Repeat steps for Internet Protocol version 4 as well.

  I hope this helps. If the problem persists, let know us and we would be happy to help you.

• Protect the DHCP with SRM

  Hey guys,.

  We are in the middle of a project of DR and have come to the point that we want to have our service ready DHCP DR.  The idea of Split range (80/20) standard is an option we are looking at, but in a DR or even single server failure there is a bit of management that is necessary to ensure the secondary DHCP server can serve all the IP addresses of all scopes (before it's 20% fills).  So we have an idea to use SRM to protect DHCP.

  We have two sites, connected via the 3 layer, with two 10GB connections between the two (for fault tolerance and load balancing).  The DR site is a live environment; It is a branch across the city (such as 30 kilometers).

  The idea of the scope of Split we have DHCP running on a domain controller in each site with the server DHCP secondary (DR) serving 20% of the IP addresses of each field and the primary DHCP serving 80%.  This can be setup using the wizard of scope of Split that MS has the Server 2008.  In doing so we cover failure of the primary DHCP server (it is also a virtual machine so HA protects too), but also the Site as the secondary DHCP server failure will be in place.  If we have an extended outage of the primary DHCP server then we need to get to the secondary DHCP server and increase all scopes, ensuring that conflict detection is on.

  Our thinking is to move the DHCP on the domain controller and give it its own virtual server.  Then, we protect the service DHCP using MRS to move it on the DR site in a DR situation.  This will cause the DHCP server to get a new IP address, as the two sites are connected by Layer 3 - the same subnets cannot exist in both places.  And that's where our thought process is getting confused...

  What will happen with the DHCP service, if the server has a new IP address?

  What is the process for DHCP clients attempting to renew its IP address:

  one) to restart the computer?

  (b) to the mark 1/2 way of their lease?

  On the one hand, I think that MRS is the easiest way to protect not only the DHCP, but also to minimize the DHCP solution management.  The scope of Split idea help to ensure that any change to a DHCP server is replicated to the other server: scope changes, scope of options changes, reservation changes, etc...

  Has anyone analyzed the all around it?

  Thank you!!

  Gerald

  That is right.  DHCP server only cares about its own address.  As long as you subnet broadcast forwarders to two IP addresses of the DHCP server so that the request hits the server DHCP it matches just MAC address for reservations of IP / scopes etc. and will work.

  Only thing to check when it rises to the DR is if the DHCP server may need approval again before DHCP works. Do not remember how it works off the coast of the hand.

• Sierra mail does not synchronize with my Exchange Server more.

  Dear community.

  After the transition to macOS Sierra Mail is not synchronize with the Exchange Server, so I can't check my e-mail from work. I deleted and reinstalled the exchange account, which did not help with the problem.

  At the same time, my iOS (iOS 10) devices keeping synchronization without any problem.

  Someone has the same problem? Any solution?

  Thank you, David

  Works fine for me on more than one Mac running Sierra. Contact your IT Department.

• How will I be informed when getting in and out a site with a secure server

  I can't find where to set the option for this. I could on Firefox 3.6
  Firefox 3.6 gives me a pop up that says I'm entering or leaving a site with a secure server. It's PARAMETERS in the Messages of warning on the Security tab in the window options. When you push the button PARAMETERS, a number of checkboxes allow for different parameters. I can't find it in Firefox 8.

  The settings for the 5 Warning Messages has been removed from security section in Firefox 4 and newer versions. These settings should be accessible through Subject: config now. So you're looking for the first and the third in the list below "parameters of the former in Firefox 3.6 on the Security Panel.

  See: http://kb.mozillazine.org/About:config

  1. type of topic: config in the URL bar and press the Enter key.
  2. If you see a cautionary, accept it (promise to be careful)
  3. Filter = security.warn_
  4. Double-click the pref in the lower panel on the subject: config display to toggle to true or false according to the descriptions below (scroll down to security.warn to see these particular preferences)
     • http://kb.mozillazine.org/About:config_entries #Security.

  Parameters of the ancients in Firefox 3.6 on the Security Panel
  
  Display a dialog warning when:

  • I'm about to view an encrypted page
    • Pref: security.warn_entering_secure
  • I'm about to view a page that uses low-grade encryption
    • Pref: security.warn_entering_weak
  • I leave a page encrypted to one that is not encrypted
    • Pref: security.warn_leaving_secure
  • I submit, information that is not encrypted
    • Pref: security.warn_submit_insecure
  • I'm about to view an encrypted page that contains unencrypted information
    • Pref: security.warn_viewing_mixed

  If this answer solved your problem, please click 'Solved It' next to this response when connected to the forum.

  Not related to your question, but...

  You may need to update some plug-ins. Check your plug-ins and update if necessary:

  • Plugin check-> http://www.mozilla.org/en-US/plugincheck/
  • Adobe Shockwave for Director Netscape plug-in: install (or update) the Shockwave with Firefox plugin
  • Adobe PDF plugin for Firefox and Netscape: Installation/update Adobe Reader in Firefox
  • Shockwave Flash (Adobe Flash or Flash): updated Flash in Firefox
  • Next-generation Java plug-in for the Mozilla browser: install or update Java in Firefox

• Pavilion p7 - 1227c needs the network drivers that work with Windows 2008 server R2

  I bought this new Pavilion P7 - 1227C at Costco so that I can install Windows Server 2008 r2 with Hyper-V role

  I managed to install Windows 2008 server but unable to t the wireless or ethernet to work.  I tried to use the driver 64 bit Windows 7 without success.

  I think return Costco if I can't get the network driver that will work with Windows 2008 Server R2

  Thanks, in advance.

  Tour37

  Hi Paul,.

  Thanks for the link, I was able to download AR816X_V.0.14.15_WHQL.

  The driver works for Windows 2008 Server R2.  I just need to find the drivers for the wireless card.

  Best regards

  Round 37

• VIX file in the user interface designer receives the data from the Web service application that communicates with the SQL server database

  I created the Web service VI ("Mt-insolacije.vi"), which has two terminals of the input string (FROM / TO) for the dates of arrival and exit of two data terminals (table 1 d) from database (MS SQL server). This VI communicates with the database with functions of the database with a DSN and SQL query appropriate palette. There are two tables with two data (time and Insolation) columns in the database.

  This VI works when you run in Labview 2010, but when I used it as VI in UI Builder it returns no data.

  Could you please help me find a solution. Is it possible to communicate with the SQL server database in this way or there is another way?

  There are two files attachmet: Image of .vix file in Interface builder and .vi file ("Mt-insolacije.vi")

  Please help me ASAP!

  Thank you

  Ivan

  I found the solution problem is in the DSN. I've been using the user instead of DSN system DSN.

  It's important to create the system DSN if you want your VI of web service to communicate with the database.

  PS Please put feature bundle format timestamp and XY graph in the web user interface designer. It's complicated to trace data with datetime on X axis without them.

• Games on the Internet give the error "a network error occurred during communication with the game server. "Error code: 0 x 80041006.

  I ran the System File Checker tool analysis. Response has been no problem with the configurations. Also, I did uninstall and reinstall. I keep getting the message: "a network error occurred during communication with the game server. "Error code: 0 x 80041006 ' this error message occurs on all the computers I own.

  Actually, no, the answer in the links were also less than helpful... suggested this, that.  Things that I had already done b4 posting my question.
  More funny: after that I posted my comment about the fault is not not in my machine and those of thousands of others, but in MS, spades servers suddenly started working again.  Coincidence? No doubt, but still...

• I wish I had a client on my PC to communicate with the Lync server, but it does not work.

  Evaluation of the VHD Lync 2010 program

  I'm quite new to Lync and I'm trying to understand how it all works. I downloaded the virtual computer files and got successfully throughout the environment, but now, I would like to have a client on my PC to communicate with the Lync server but I'm not having any luck.

  Here are the servers that I have:

  DC

  Exum

  Lync-Qms

  Lync-Se

  SPS2010

  These are all in an internal network and I gave the Lync-SE server outside access, assuming that it's the server that my client needs to communicate with because he runs the Lync server. Initially, I was getting a certificate error. I exported the certificate of the server DC, installed on my client and the client toward the DC server who gave me the certificate number, but now I get an error that the server is temporarily unavailable. I'm far from base here?

  Hello

  Thank you for visiting the Microsoft answers community site. Your question is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows 7 Server forum.

  http://social.technet.Microsoft.com/forums/en-us/category/OCs

  I hope this helps.

• Foundation of windows server 2008 comes with the fax server role?

  Foundation of windows server 2008 comes with the fax server role?

  Hello

  I suggest you to send your request from the link and check.

  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

• Application built with an OPC Server

  Hello everyone
  I build the application on the development using wich S7 computer - connected to the OPC Server 1200
  and I want to build the application to run the VI on another PC without installing labview, however when I finished to build the application with the installer and install the application on another PC it cannot connect to shared variables so I installed an opc Server ON this machine and add the server to the software mutual FUND that contains tags and variables
  but it is not also connect to the opc Server
  So how do you run the application on another PC with an opc Server!
  How the VI to use a specific opc server on this PC with no labview?

  Hello

  What do you call the OPC Server? You are creating a mutual FUND of LabVIEW client and linking to the shared variable? If this is the case while you use the LabVIEW DSC module and it works very well in the development environment.

  However, every time that you deploy (creation of executable or installer) a VI using DSC module, you must have a license to run on each computer that runs the executable file. http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/210561

  the alternative would be to use the socket api in LabVIEW to call the server.the attached VI OR OPC illustrates how.

  I hope this helps!

• Update KB937287 keep apearing as the only updated, try install many times, but does not work, tried it with the standalone version and it keeps apearing

  Update KB937287 keep apearing that the only update, tried to install a lot of times, but does not work, tried it with the standalone version and it keeps apearing, when I install it does not display an error message, just say that again was successful but when I try to look for more updated it apears again.

  Hi mayortom,

  Thank you for visiting the Microsoft answers Forum.

  You can follow the steps outlined in the article below:

  Troubleshooting Windows Update or Microsoft Update when you are repeatedly offered an update
  http://support.Microsoft.com/kb/910339/

  I hope that helps!

  Thank you and best regards,
  Abdelouahab Microsoft responds to the technical support engineer