IQ816 double video screen LCD (multiplex) problem

I have an iq816 in which the motherboard just died, then it wouldn't turn on, POST, nothing. The motherboard has been replaced and the system now starts at the bottom of windows very well with one exception: all that is shown on the display is multiplexed 6 times. The image to fill the entire screen fills to only 1/6 of the screen and is repeated 6 times. The machine has no video output, so I can't test an external monitor.

Here's what I know so far:
1. the symptom appears during the during the POST, not only in Windows and BIOS configuration screen, then it cannot be a driver problem.
2. the system has a video card discrete MXM and two LVDS ports on the motherboard (LVDS2 for discreet video) and LVDS1 for the embedded video. I already tried to remove the discrete video card and connecting the LCD to LVDS1 (integrated video), but the problem persists, this isn't a video card problem.
3. in the configuration of the BIOS, the machine claims to be an iq504, not an iq816. I know that the machines take the same motherboard (same HP reference at least), so I don't know whether to be alarmed by the present or not. I tried to Flash the latest BIOS for the iq816, but the listed model is always incorrect. Is there another firmware, I need to flash, or is it a distraction?
4. There is a set of DIP switches on the motherboard that I have not found any documentation on, but they are labeled GPIO, so I doubt they will help. Yet, no idea this here?
5. There is a block of jumpers 8-pin without a label. I think that the bit is used to reset CMOS and reset password, but would like to know what are the other pins.

6. the causes I can think of:
A. bad cable LVDS (other on command - update)
B. bad screen LCD (game over)
C. something to do with this strangeness of motherboard model

Thanks for any help/insight!

Hey joesuffceren,

I'm sorry that you use in this show, but thank you for providing this useful information! I did some research on your motherboard.

Here is a link showing the motherboard specifications - develop internal connectors

GPIO is listed there as the DIP switch used in the factory to match the motherboard to the LCD so it might be your answer. I searched for any kind of documents I can find on which positions the rider must be on for the iq816 but have not yet find something. I wanted to get this information for you right where you want to go ahead and try changing this autour rider to see what works.

I hope this information helps! Forward to your response

Tags: HP Desktops

Similar Questions

  • dust behind the screen LCD - common problem?

    Hi, I recently bought a toshiba EQUIUM A60-181, and I'm
    facing a problem with the LCD screen.
    There seems to be a defect or the dirt behind the glass
    because it blocks the light of a pixel. Any attempt of
    apply moderate pressure to move this filth that has failed. I was
    I was wondering if it is common with screens LCD expect a sort
    I can't believe that this has passed quality of imperfection
    control. Have I not justification for firing
    toshiba for fixing, it is barely 1 week old?
    I have read the warranty booklet and there is no mention of
    dead pixel return policy can you elaborate on what is
    and what is not covered by the warranty?

    see you soon,

    Richard.

    Hello

    In my opinion, you should contact the Service partner. You have purchased a new product and if you see that there is something wrong, you can contact them. I'm sure that the technicians can give you more information on this issue.

  • Cisco profile 52/55 double - video screens on a single screen after software upgrade 7.1.4

    Hello

    I improved 52/55 to TC 7.1.4 double profile system and it displays more video on two screens at a conference. It displays the contents of the second fine screen. He worked in version 6, so I'm wondering if something changed in the software or endpoint requires additional configuration.

    I checked the settings under Configuration > system setup > video > monitors and it is set to Dual. I changed a few times and set it to the double, but this does not solve the problem. I do not see any option button double screen added under system information, but I guess that's an option double screen so it's a dual monitor system.

    I need to change any settings?

    Cisco has changed how layouts behave after TC6 on C-series systems. If you want your system behave in the same way as a Tandberg MXP more used to work (end of full screen on a single screen) and selfview full screen on the other, you can do the following telnet commands:

    xconfig video monitors: double

    xconfig video CamCtrlPip CallSetup Mode: Off

    xconfig video SelfviewDefault Mode: Off

    xconfig video SelfviewDefault OnMonitorRole: second

    xconfig video SelfviewDefault modepleinecran: on

    I had a lot of customer complaints after the upgrade and these orders have been tested by Cisco and I've applied to many of my clients and it works.

    Hope this helps your case

  • Blue screen errors the problem points to the files Volsnap.sys or Classpnp.sys.

    Last month, I had a series of blue screens.  The problem points to the files Volsnap.sys or Classpnp.sys.

    I have a Dell Precision T3500, running 64-bit Windows 7 Prof.  The system is configured with RAID.

    Sometimes rebooting the system in the middle of the night and sometimes it freezes while I work on that.  It is during the night to safeguard and Virus scanning using Trend Micro, which is the only type of trainer of spam on the system.

    No idea on how to stop this would be really appreciated!  Thank you

    Hello

    Results verified BlueScreenView WinDBG / DumpCHK.

    TrendMicro is most likely part of this question, as it is known to have caused or
    make these problems worse. Uninstall it and run the removal tool to prevent
    remains of troublecausing. The following recommendations to use during the test,
    even better all the time.

    TrendMicro removal tool
    http://eSupport.trendmicro.com/pages/how-do-I-remove-old-or-new-versions-of-trend-micro-products-in-my-comp.aspx

    List of tools to clean/uninstall anti-malware programs
    http://social.answers.Microsoft.com/forums/en-us/msestart/thread/407bf6da-C05D-4546-8788-0aa4c25a1f91/

    ------------------------------------------------------------

    Here's what I use and recommend: (these are all free and very effective versions.)

    Avast and Prevx proved extremely reliable and compatible with all I have
    launched on them. Microsoft Security Essentials and Prevx have also proven to be very
    reliable and compatible. Use MSE or Avast and Prevx, Prevx 3 but not all.

    Avast Home free - stop any shields is not necessary except leaving Standard, Web, and
    Operation of the network.

    Prevx - Home - free

    Windows Firewall

    Windows Defender (is not necessary if you use MSE)

    Protected IE - mode

    IE 8 - SmartScreen filter WE (IE 7 phishing filter)

    I also IE always start with asset if filter InPrivate IE 8.
    (It may temporarily turn off with the little icon to the left of the + bottom
    right of IE)

    Two versions of Avast are available 6.x and 4.8 x

    Avast - home - free - 6.x stop shields you do not use (except files, Web, network, &)
    Shields of behavior) - double click on the icon in the Notification area - real time Orange - click on the
    Shield that you want to stop - STOP. To stop the Orange icon to show an error indicator-
    Click on the Orange icon - top right - settings - click on the status bar - uncheck shields you
    disabled - click OK
    http://www.avast.com/free-antivirus-download

    Avast 4.8 x - home - free - stop shields, you don't need except leaving Standard, Web,.
    and the network running. (Double-click the blue icon - look OK. - upper left - Shields details
    Finish those you don't use).
    http://www.avast.com/free-antivirus-download#TAB4

    Or use Microsoft Security Essentials - free
    http://www.Microsoft.com/Security_Essentials/

    Prevx works well alongside MSE or Avast

    Prevx - home - free small, fast, exceptional protection CLOUD, working with other security
    programs. It is a single scanner, VERY EFFICIENT, if it finds something come back here
    or use Google to see how to remove.
    http://www.prevx.com/   <-->
    http://info.prevx.com/downloadcsi.asp  <-->

    PCmag - Prevx - Editor's choice
    http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

    Also get Malwarebytes - free - use as scanner only. If you ever think malware and that
    would be unusual with Avast and occasional Prevx running with the exception of a low level cookie
    (not much), to UPDATE and then run it as a scanner. I have a lot of scanners and they
    never find anything of note that I started to use this configuration.

    http://www.Malwarebytes.org/

    ==========================================================

    The Bug_Checks were D1 (19 long happened if he should really
    do not be in the mix) and CAUSE volsnap.sys classpnp.sys which are
    Components of Windows, which means something else led in error.

    1. Uninstall TrendMicro as it has a role - is not enough to just disable
    such that it will still load chunks of itself in memory.

    2 Volsnap.sys is the Windows volume shadow copy driver and disk problems
    or other corruption could be at stake. Classpnp.sys is the SCSI class system
    dll checking and disk problems will affect the it. Run SFC/scannow, and then
    Checkdisk (chkdsk /f r).

    Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

    Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

    sfc/scannow

    How to fix the system files of Windows 7 with the System File Checker
    http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

    Then run checkdisk (chkdsk).

    How to run check disk in Windows 7
    http://www.SevenForums.com/tutorials/433-disk-check.html

    =========================================================

    Other troubleshooting methods:

    BCCode: D1 0x000000D1

    Check these KB

    Stop error when you resume a computer that is running Windows 7 or Windows Server 2008 R2
    from sleep or standby extended: "STOP: 0x000000D1".
    http://support.Microsoft.com/kb/978982

    Stop error on a computer based on Windows Server 2008 R2 or Windows 7 during operation
    system uses a storport virtual miniport driver to save a dump file or a file of hibernation: "0x000000D1.
    http://support.Microsoft.com/kb/2320550

    Those 7 other KB Articles are available
    http://support.Microsoft.com/search/default.aspx?mode=a&query=0x000000D1&SPID=14019&catalog=LCID%3D1033&1033comm=1&Res=10

    --------------------------------------------------

    Think video drivers especially if it may be others. Refer to the section of driver in my generic bluescreen
    methods of troubleshooting below. BIOS, low and antispyway/antivirus/security chipset drivers
    programs may also cause this. Check the resolution of the problems and when you get to the pilot and sections tests memory refer to the generic methods in the next message and then returns to the resolution of problems
    If necessary.

    Cause

    A driver tried to access a pageable (or that is completely invalid) address while the IRQL was too high.

    This bug check is usually caused by drivers who used a wrong address.

    If the first parameter has the same value as the fourth parameter, and the third parameter indicates a runtime operation, this bug check was probably caused by a driver who was trying to run code when the code itself has been paginated outside. The possible causes for the error page are:

    • The function was marked as pageable and was operating at an IRQL higher (including obtaining a lock).
    • The function call was made to a function in another pilot, and that this driver has been unloaded.
    • The function was called by using a function pointer that was an invalid pointer.

    BCCode: d1 0x000000d1<-- read="" this="">
    * 1210.html? order = votes http://www.faultwire.com/solutions-fatal_error/Driver-IRQL-not-less-or-Equal-0x000000D1-

    =========================================

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
    TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.

    http://www.NirSoft.NET/utils/my_event_viewer.html

    -------------------------------------------------------------------------

    Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
    info that would help. Such as ITC and 4 others entered at the bottom left. And all others
    error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during 'blue screen of death '.
    hangs and displays information about all accidents of a table - free

    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
    There are other causes.

    You can do mode if necessary safe or the Vista DVD command prompt or
    Options recovery if your system is installed by the manufacturer.

    How to start on the System Recovery Options in Windows 7
    http://www.SevenForums.com/tutorials/668-system-recovery-options.html

    You can try a system restore to a point before the problem started when one exists.

    How to do a system restore in Windows 7
    http://www.SevenForums.com/tutorials/700-system-restore.html

    -------------------------------------------------------------------------

    Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to fix the system files of Windows 7 with the System File Checker
    http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates cbs.log Windows Vista (and Windows 7)
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Says not all possible
    driver problems).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

    How to run the check disk at startup in Windows 7
    http://www.SevenForums.com/tutorials/433-disk-check.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
    keyboard and mouse, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    Installation and update of drivers to 7 (update drivers manually using the methods above is preferred
    to make sure that the latest drivers from the manufacturer of system and device manufacturers are located)
    http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
    quit unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    Startup Options recovery or Windows 7 disk repair

    How to run a startup repair in Windows 7
    http://www.SevenForums.com/tutorials/681-startup-repair.html

    How to start on the System Recovery Options in Windows 7
    http://www.SevenForums.com/tutorials/668-system-recovery-options.html

    How to create a Windows 7 system repair disc
    http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

    I hope this helps.

  • Satellite S1410-802 cannot play videos on LCD data projector

    Hello

    When I connect my Toshiba S1410-802 to LCD data projector and I start all the video (in WMP and other programs) that I see on the wall are black video window but all around is displayed correctly (i.e. desktop and other windows open). On laptop, video screen appears correctly. In summary: I can watch videos on laptop, but when I switch to the projector I see everything except the video (black window)! Any guess?

    --
    Best regards, Artur

    Hello Artur

    I'm not 100% sure but I think you cannot watch video on the screen LCD and the external device at the same time and you can watch it on the LCD screen or an external display only.

    Please test. As far as I know this is a technical limitation.

  • Cannot insert a video screen or modify an existing one

    Hello

    Anyone know why I can't insert a video screen or change any existing? As shown in the screenshots all my video files options are grayed out.

    Figured it out, I had accidentally activated my software as basic editing.

    I have used the License Manager OR to activate Professional edition with DAC Bundle and video options can now be selected.

    Edit: I do not mark my own post as a solution to my question, but someone else may have the same problem I did it anyway.

  • In 3 simultaneous video screens

    I try to implement my Alienware M14X R2 to work with 3 screens: 2 screens (Dell) external and internal monitor (laptop). The two external monitors are connected as follows:

    • An external monitor is connected to the Alienware laptop via a DVI cable to HDMI.
    • The other external monitor is connected to the Alienware laptop via a VGA VGA cable.

    I can't do this configuration works with any combination of parameters. I can get both of these screens to work, but not all three.

    The other thing that is a little concerning, is that when I pull the NVIDIA Control Panel, it shows that all three screens are controlled by the 4000 Intel HD integrated graphics adapter and none are controlled by the Nvidia GEForce GT 650 built-in discrete graphics adapter. Yet once, nothing I tried (apart from disabling the Intel card) could change the allocation of video screens to graphics cards.

    Once more, the main objective is to have a working configuration 3 screen display.

    Does anyone know of a fix software or hardware for this problem?

    previous post on this:

    en.Community.Dell.com/.../19615511

  • HP 550 153na: video screen

    Can I use my old video of screen on my computer it hs taken the old (and you show one in the connection for this model guide) or do I have to buy a new screen with HDMI

    Hello Baldock ;

    Let me welcome you on the HP forums!

    I read your post on the reuse of your old video screen in Win10 and wanted to help.

    If you mean using the screen as a monitor, there is no reason to have to buy a new one for Win10.

    As long as you have the correct video cables that hold the two connectors on the PC and on the old screen, you should be able to get a display with no problems.

    However, the display will be limited to the max of the old screen resolution and some of them are 1024 x 768.  If you are not sure, you can Google the old screen model number and be able to find the resolution taken max supported.

    Good luck

    I'm a volunteer and I do not work for, or represent, HP.
    ========================================================================
    If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!

    If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

  • How to set up two monitors with screen LCD and HDTV on computer that is running Windows 7

    Issues of identity and position monitor

    I use a LCD and an HD TV on my computer. I have HDTV mounted to my left on the wall in my room and the LCD is on my desk in front of me. I have my monitor set as my main screen and HDTV as secondary. Windows identifies the HDTV as monitor 1 and my screen LCD 2. After starting the computer they work very well as they should. My problem is during the boot process. When the computer starts, it displays only the boot screen/POST on monitor 1 (HDTV) but not my main screen #2 (LCD). This is a problem when I don't have my HDTV now, I don't see the MESSAGE options. I don't want to always have my HDTV and crane my neck every time I need to change the BIOS settings or use the MESSAGE options. Is there any solution for this?

    Chris

    AMD Penom II x 4 940

    Windows 7 64 bit

    Gigabyte GA-MA770-UD3

    NVIDIA GeForce GTX 275

    DCLCD 19 "VGA monitor

    VIZIO HDTV 32 '' (hdmi) "

    Hi Darth Polizei,

    I hope that's not redundant but did you try to set your monitor 19 "as the main display?

    1. In the screen resolution window, you click the icon of the monitor that represents the secondary monitor.
    2. You click to select the "Make my main screen" check box, and then click OK.
    3. You log out of the computer.
    4. You log on to the computer.

    Please let us know.

    Thank you!

    Debra
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think

  • Can I output the monitor program PremierePro CC (only) to a 2nd video screen?

    I already have (years) used PremierePro on an edition of PC system. At this time, I used a box of cards and small groups of Matrox - it was so easy to put in place a 2nd monitor to display the program output (only).

    I started using new PremierePro (CC version) but this time on an iMac 27 "retina 5 k (max for the ram, processors and graphics functionality). I'd quite like to discover the program output only (or at least mostly) on a 2nd 1080HD video monitor. Is it possible to do? With no junction box, I guess that this cannot be done. Is this fair?  I know I could set up an iMac HDMI output, but that would be out of the whole office. I just want to really take a power of video output (monitor of the program only) rather than the entire desktop. Is it some sort of break Thunderbolt to send with a HDMI or DVi connection, which can display only the monitor program (like those old buttons)?

    Of course the iMac screen 5 k and the video monitor will be quite different devices - so I can't really just the range double configuration screen. A 2nd screen Mac is expensive - and it would be another screen to the retina, 5 k.

    As background information, for now I'm only editing content 1080HD that thus the 2nd monitor should be consistent 1080HD. I have various computer and video monitors available if this configuration is possible. I'm not too concerned about the quality of the image in the 2nd monitor - its more about speed reading to check for sync and motion - changes especicailly when a customer sits the long side (and Yes, I hate too). The iMac 27' is a good size screen, but I'm edition multi channel animation graphics and pictures (no animated videos), it fills the screen fast enough. If I want to program a monitor window half-decent size, I am constantly scrolling and minimization / maximization of the channels that I can see detailed work areas easily.

    If I ask a stupid question here, please don't shoot me :-) As I have said for a while I used the PP, but now I use it everyday - so just going back to it.

    Thanks for reading - and advice you might have would be welcome.

    Thank you.

    Pete

    If all you need is a program-monitor output to a second monitor, woudn't integrated two-monitor process work? No, is not the release of calibrated equipment which is often sought for high range editing, but it works for most cases... just have a second monitor mounted on your card system and on the Preferences tab, select it as shown...

    Just make sure that your operating system 'sees' your normal monitor as a screen, and then they will appear in this dialog box as your operating system lists them. PrPro always default to sending the output of the program monitor to monitor 2.

    No box necessary engine... and many who have the outboard motor to run a high-end TV, also use it for their treatment of General works.

    Neil

  • Using an IP191 monitor, have random horizontal stripes on the screen - have no problems with other browsers. also no problem with FF on the other PCs on the family

    Using an IP191 monitor, have random horizontal stripes on the screen - have no problems with other browsers. also no problem with FF on the other PCs on the family.

    These "streaks" seem to be the domain of the high frequency analysis; they can be eliminated by scrolling upwards or downwards.

    Hello, maybe it's a problem with hardware acceleration - try updating your graphic driver, or in case this does not solve the problem, or there is no new version available at the time, disable hardware acceleration in the firefox menu

    > options > advanced > General.

  • With more than 2 GB videos for veiwing h264 problems, they won't play in windows or version mac et seq., less than 2 GB, they play very well.

    I work for a video company, video encoding, the only problem we have is Firefox plays videos not encoded as H 264 (1080) greater than 2 GB, because they do not play. I tried the two latest version 9.0.1 in mac and windows and no change. In Internet Explorer, Chrome, the video plays well. Is there a file limit in Firefox? I read somewhere else that FF also has problems downloading files of 2 GB, do not know who is bound. Any help would be appreciated.

    Firefox does even not play H264 content by default. For HTML5 video, it will play OGG / Theora and WebM, but a plugin is necessary for the H264 content.

  • Satellite 5205-S505 - support wide screen LCD TV?

    I have a new wide screen LCD TV with a VGA port, I connected this with my old Satellite 5205-s505 via the VGA port as the second screen. But it displays 'unsupport signal' on the TV screen.

    Can someone have the answer.
    Thanks anyway.

    Hey,.

    I think that it s according to the external display what resolutions it supports.
    Normally, your computer user manual laptop, you will find a list of the supported screen resolutions and you should check this!

    I also recommend to install the last page of Toshiba display driver.

  • -What sound effects and themes in iMovie legal to use on a youtube video without the copyright problem.

    -What sound effects and themes in iMovie legal to use on a youtube video without the copyright problem.

    Yes.

    Geoff.

  • MacBook Pro screen re-recurring problem.

    In November 2015, I got a replacement of the screen as my Mac anti-glare treatment wears.

    Just one month later, replaced screen got weak horizontal gray bands that goes further, from right to left, I got a replacement of the screen before the end of 2015.

    Now, the March 2016, I had some stripes of vertical pixels affected when I apply pressure on the screen. How can I fix?

    Just in case you are wondering this odd task between the two, it is the slider. I want to show that the screen has some problems with it, so I place my cursor here to show that this isn't where the screen ends.

    It is a hardware problem with no software solution.  It will require a replacement.

    You have not identified the EXACT MBP model you have and perhaps with the display problem, it could come under this replacement program.  Read this link.

    https://www.Apple.com/support/MacBookPro-videoissues/

    Ciao.

Maybe you are looking for

  • Re: Satellite L505 - 13 X - update BIOS for Linux

    Hello I see that there is an update of the BIOS for my Satellite L505-13 X. However, it is a .exe and he would go on the wine? Is it necessary to update? I have a serious overheating problem. # An update would I read on some forums?

  • When I rename an iOS device should I update my iCloud account?

    I have four iOS devices: two iPhones and two iPads. If I rename one of them (in settings, general, all) what I need to also connect to applid.apple.com and play with the list of devices, named it there? The same question could be applied if I get rid

  • 1000 1401AU

    Hello experts, My portable 1000 1401AU Boot Manager screen shows no CD/DVD-ROM DRIVE. I followed the solution given in link http://support.HP.com/us-en/document/c03736054 Boot Manager still shows no rom dvd drive. Dave.

  • Resolution for blackberry

    Hello I want to ask resolution for blackberry... We can help me forget for the resolution of blackberry? How much resolution on blackberry and adding the type of blackberry concerning Andi

  • How to fix corrupted files of the sfc scan?

    These are the errors obtained in the sfc scan: 2013-05-14 20:14:50, 000000e8 CSI Info [SR] cannot repair the military record [l:22 {11}] "PINTLGB. IMD"Microsoft-Windows-IME-Simplified-Chinese-Core, Version = 6.1.7601.17514, pA = PROCESSOR_ARCHITECTUR