Irql_not_less_or_equal blue help screen / / / 0x0000000A

Hello! Recently I was making a few different blue screens. After a few different system restores, I only get 1 now. It's the irql_not_less_or_equal.

For a few months now, I was not using my computer until within the last few days, because for a while, I need new RAM. And I thought I needed a new graphics card, because I had problems with my monitor (it became very pixelated/signs of him dying). Although, I don't have my installed latest graphics card.

My computer will last between 5-15 minutes until I get this blue screen.

I went from 2 GB of RAM DDR2 up to 8 GB DDR3 (2 of 4 GB each). Recently, I was not able to boot my computer. After hours of trying to figure out why, I watched my RAM and 1 of them had burnt/burned some how. I don't know when or why. POM I have removed that one and I kept the right thing and put it on the opposite side of where the other burned. Because I had removed the charred/burnt RAM, I am now able to boot my computer very well.

I am currently using my old graphics (NVIDIA Geforce 8500 GT)
My system specs are:

Windows Vista Edition Home Premium
Service Pack 2
Processor: Intel (r) Pentium (r) D CPU 3.73 GHz
(Vivid RAM) memory: 4.00 GB
System type: 32-bit

Windows Update is current. Each update it can find, I installed. My graphics card is up-to-date as well. I ran a memtest86 + on my 1 stick of 4 GB of RAM, and it found no problem. I also used Rkill, MalwareBytes, and MSE to see if it was virus/etc. related. No problem.

I wrote down the info, when I saw a blue screen. This was also the last blue screen, I'm currently in Mode safe mode w / Networking:
Irql_not_less_or_equal
STOP: 0X0000000A (0X0000001B, 0X00000000, 0X00A20BA4, 0X830B8352)

I'm not too familiar with the system logs/event viewer. So, I downloaded Blue Screen Viewer, (just in case). I'd appreciate any help!

Thank you very much
Cody

Hi Cody,

 

Please join Microsoft Community where you can find the necessary information on Microsoft products!

 

You get bluescreen error Irql_not_less_or_equal STOP: 0x0000000A (0x0000001B, 0x00000000, 0x00A20BA4, 0x830B8352).

The problem may occur if any of the hardware devices are defective or the drivers are corrupt.

What is brand and model computer?

To check if the problem is with a malfunction of the devices or drivers, I suggest you follow the steps described in the mentioned site:

How to fix a blue screen stop errors that cause Windows Vista to shut down or restart unexpectedly

http://support.Microsoft.com/kb/958233

Note: When you restore the system to a previous state, programs and updates installed later will be deleted.

WARNING: If you restore Windows from disk from the manufacturer, you will lose all the programs and data.

Note: This article is also applicable to the Vista Service pack 2.

It would be useful for us to identify the problem, if you could upload the dump file.

You can use the Sky-drive to download the dump file. Check the link for the steps on how to download Sky-Drive.

http://social.technet.microsoft.com/Forums/en-US/w7itproui/thread/4fc10639-02db-4665-993a-08d865088d65.

The location of the dump file is C:\Windows\Minidump\.

I hope this helps. If the problem persists, let know us and we would be happy to help you.

Tags: Windows

Similar Questions

  • Error IRQL_NOT_LESS_OR_EQUAL blue screen

    Hello

    I just bought HP Pavlion dm4 1209tx and I get an Error IRQL_NOT_LESS_OR_EQUAL blue screen. It occurs usually when I play music or watch videos. Initially the system will just hang, then the blue screen appears. I'm just a beginner so any help will be greatly appreciated.

    Thank you!

    I was able to update the driver, thanks to you!

    So far, the system is not suspended yt or givng me a blue screen. I really hope that I won't get any more problem.

    Once again, thank you!

  • IRQL_NOT_LESS_OR_EQUAL Blue Screen on Vista Home Premium x 32

    Hello

    In the last 2 months I was struggling with my computer. He keeps "overload" the RAM on its own, even if I'm just surfing the web or playing a game. I don't have a lot of programs running, just TuneUp Utilities, Microsoft Security Essentials, and Dropbox.
    After about 20-30 minutes of use, my PC would come with this "IRQL_NOT_LESS_OR_EQUAL" blue screen of death. I tried everything, including: MemTest, cleaning the dust out of the inside and defragmentation. MemTest encounter errors with my RAM and this leaves me really clueless as to what is causing the problem... Everything is up to date so it cannot be a driver problem either.
    Any ideas?
    Thanks in advance.

    You are welcome to help.

    Driver Realtek can you, in the device, right-click the NIC Realtek Manager and select "Uninstall".

    In addition, choose "Remove the driver for this device" > OK

    Restart the computer and let Windows redetect the device and install the drivers.

  • Had sent the message about the Blue error screen. Has been asked for more details. I hope this helps.

    Had sent the message about the Blue error screen.

    Has been asked for more details.

    I hope this helps.

    BCCode: 10000050 BCP1: FFFDF6F4 BCP2: 00000001

    BCP3: BF90DB41 BCP4: 00000000

    OSVer: 5_1_2600 SP: 3_0 product: 768_1

    Hi VASANTHFERNANDES,

    ·         You did changes to the computer before the show?

    ·         When exactly you receive the blue screen error?

    ·         What is the full error message?

    Follow these methods.

    Method 1: Disconnect all external devices and check if the problem persists.

    Method 2: Start the computer in last known good configuration and check.

    How to start your computer by using last good known Windows XP Configuration

    http://support.Microsoft.com/kb/307852

    Method 3: Follow these steps:

    Step 1: Start the computer in safe mode and check if the problem persists.

    A description of the options to start in Windows XP Mode

    http://support.Microsoft.com/kb/315222

    Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

    How to configure Windows XP to start in a "clean boot" State

    http://support.Microsoft.com/kb/310353

    Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

    After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

    (a) click Start, run.

    (b) type msconfigand click OK.

    (c) the System Configuration Utility dialog box appears.

    (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

    (e) when you are prompted, click on restart to restart the computer.

    Method 4: Follow the steps in the article to check the drive for errors.

    How to perform disk error checking in Windows XP

    http://support.Microsoft.com/kb/315265

    Note: If bad sectors are found in the hard drive, then it could try to fix this particular sector. If you have any data on that, it can get lost.

    For reference:

    Demystifying the 'Blue Screen of Death'

    http://TechNet.Microsoft.com/en-us/library/cc750081.aspx

  • BAD_POOL_CALLER and DRIVER_POWER_STATE_FAILURE help Blue death screen

    On 24 December, I built my computer and I had the BAD_POOL_CALLER Blue error screen dead 25. The same day, I ran memtest86 for nearly 3 passes (it takes more than 5 hours at that point and I needed to use it) and found no errors.

    I also received the blue screen error DRIVER_POWER_STATE_FAILURE on January 7.

    My current features:

    Intel Pentium G3258 (Stock # 3.2 ghz)

    ASRock H97M Motherboard Pro4

    G.Skill Ripjaws X (2 x 4) memory of 8 GB DDR3 - 1600

    Western Digital Caviar Blue 1 TB HARD drive

    EVGA GeForce GTX 950 video card FTW

    EVGA 500W power supply 80 +.

    Link to two dump files.

    https://onedrive.live.com/?AuthKey=%21AE20ovaEMav_roM&ID=E2C257A8C93A1ABD%21117&CID=E2C257A8C93A1ABD

    Thanks in advance.

    If the drive passes both tests, it should be considered safe to use.
    I would consult with the guys from live support to the MS for the necessary drivers. The guy he should be able to provide adequate and specific support for the required drivers and appropriate places to get them. :)

    Captain_WD.

  • Need help with the Blue error screen.

    I'm having problems with the Blue error screen at startup which said "less than or equal Driver_IRQL_not. He entered the State of memory dump & black screen after that.  Nothing was abnormal after checking all the drivers in windows 7 Edition Device Manager Home premium. I'm really lost as to what causes it? My computer is a toshiba satellite laptop computer P840 pourrait-someone ' a please advise me on this matter. Thanks in advance for your patience.

    Dear Zigzag3143,

    I finally managed to fix the problem by the chance. I had discovered that this problem was caused by the sypnatics of the laptop touchpad driver. Uninstalled A & reinstall it with the correct driver from the laptop manufacturer websites. Did not expect that it is the cause of all the problems. Thank you for your valuable advice.

  • My drive hard wd crashed. After the replacement, the computer is located on the blue HP screen. Help.

    My 1 TB WD drive crashed.  I replaced it with another disk of 1 TB WD.  When I turn on the computer and insert the recovery disk, nothing happens.  It is located on the blue HP screen.  I hit esc, nothing.  I hit F11, nothing.  I'm stuck.  Probably something simple, but I can not understand.

    brackman63 wrote: it seems that refusal to acknowledge this new record is due to failure of the motherboard according to a friend who works in it.  I imagine that will lead to an expensive repair and may not be worth the effort.  a new computer may be in my future.  Oh joy...

    Hello brackman63, this is possible, but I have never had this problem in more than 25 years of working on computers

    You can see if you can install a Sata addon hard drive controller card. There are some of them which are not very expensive. There is of course no guarantee that it would work.

    If the disk controller hard motherboard is defective, then the original hard disk can still be good.

    Just some thoughts.

  • Blue error screen when indexing the files on Vista computer

    Original title: Problem Event Name:_BlueScreen__ OS Version:_6.0.6002.2.2.0.768.3__ Locale ID:_1033__

    BCCode: f4

    BCP1: 00000003

    BCP2: 872E2D90

    BCP3: 872E2EDC

    BCP4: 81E33710

    OS version: 6_0_6002

    Service Pack: 2_0

    Product: 768_1

    Before I tear off my hard drive and throw it out the window, please tell me I can recover from this error. The above error when I try to rebuild my Index. I regularly get messages "index has stopped working". I select the indexer rebuild to the original configuration. He tried to do, but stopped after the indexing of files about 1700, restarted, and then returned with the above event. I had several problems with my OS for a few days. I have run chkdsk and chkdsk/r several times. I use Norton 360, analysis tell me that all files are up to date, Windows update is performed regularly and is up to date. I was initially received an error "parameter has exceeded its normal range" train SMART. I disabled this option considered, but service to have problems with my system. Everything seems to work okay in safe mode, where I am now. I am at a loss. I have a recovery partition on my drive, but did not know what options to use. I have the installation CD Vista too, but avoided to reinstall, have done this before for another question. For any help or suggestion will be greatly appreciated. Please see my other post earlier this week, I was only partially successful with this process. Thank you very much!

    Hello

    If a PC remove all power to the system:

    Check and replace the cards, memory and cables (at both ends) actually remove and replace
    -do not just tight. Memory could be the problem, so if you have more than 1 stick swap
    in and out to see if the problem follows a stick or try the new memory. How to test
    memory in the next message.

    -------------------------------------------------------------------------------------------------------

    Pick up the pieces after a computer crash - includes "what to do if Windows doesn't.
    start correctly'    .
    http://Windows.Microsoft.com/en-us/Windows-Vista/picking-up-the-pieces-after-a-computer-crash

    Check this thread for more information using BlueScreenView, MyEventViewer and other methods
    to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

    http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

    We can analyze the minidumps if make you it available to the SkyDrive or another file
    sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
    for the office or in the Documents folder and download them from there.

    ZIP or download the content of the C:\Windows\minidump

    Use SkyDrive to upload collected files.
    http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

    ================================================================

    BCCode: F4 0x000000F4

    Check and reinstall the cards memory and cables (at both ends where possible) actually remove and
    replace - do not just tight. On a laptop computer on all you can do is reinstall the memory and possibly check
    the contacts/connection to the hard drive. Memory could be the problem, so if you have more than 1
    stick swap them in and out to see if the problem follows a stick or try the new memory. Antivirus/anti-
    spyware/security programs have been known to cause or have a role in this matter.

    More general patch updates day and low level chipset BIOS drivers and other software to control.
    Also check wiring for hard drive.

    ======================================================

    Bug Check 0xF4: CRITICAL_OBJECT_TERMINATION

    CRITICAL_OBJECT_TERMINATION bug control has a value of 0x000000F4. This indicates that a process or thread crucial to system operation has unexpectedly is released or ended.

    Important info if you received a STOP Code

    If you received a blue error screen, or a stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error. If your copy of Windows is shipped with your computer, contact your computer manufacturer. If you purchased Windows separately from your computer, Microsoft provides support. To find contact information for Microsoft or the manufacturer of your computer, Contact Support.

    If you have experience with computers and try to recover from this error, follow the steps in the Microsoft article solution STOP (blue screen) errors in Windows.

    These actions could prevent a mistake like this does not happen:

    1. Download and install updates for your computer from Windows Update device drivers.
    2. Scan your computer for computer viruses.
    3. Check your hard drive for errors.

    CRITICAL_OBJECT_TERMINATION parameters

    The following settings are displayed on the blue screen.

    Parameter Description

    1

    The Terminal object type:

    0 x 3 : Process of

    0 x 6 : Thread

    2

    The endpoint object

    3

    The name of the process image file

    4

    Pointer to a string ASCII containing an explanatory message

    Cause

    Several processes and threads are necessary to the functioning of the system. As they are completed for some reason, the system can no longer function.

    BCCode: F4 0x000000F4<-- read="" this="">
    * 1241.html http://www.faultwire.com/solutions-fatal_error/A-process-or-thread-crucial-to-System-Operation-has-0x000000F4-

    -----------------------------------------------------------------------------

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard event viewer
    Windows. TIP - Options - Advanced filter allows you to see a time rather
    of the entire file.
    http://www.NirSoft.NET/utils/my_event_viewer.html

    Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
    info that would help. Such as ITC and 4 others entered at the bottom left. And all others
    error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during ' blue screen of the.
    death ' crashes and displays information about all accidents of a table.
    Free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by drivers of old or damaged, in particular the video drivers
    However, there are other causes.

    You can do mode if necessary safe or the Vista DVD command prompt or
    Options recovery if your system is installed by the manufacturer.

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    You can try a system restore to a point before the problem started when one exists.

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    -------------------------------------------------------------------------

    Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
    RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
    program generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Does not work
    tell all possible driver issues).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
    keyboard and mouse, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
    quit unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting, STOP error blue screen Vista
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    The Options or Vista recovery disk Startup Repair

    How to do a startup repair
    http://www.Vistax64.com/tutorials/91467-startup-repair.html

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

  • Blue error screen Stop 0X0000007E (0XC0000005, 0X8070194F, 0XF78DAC30, 0XF78DA12C) and when ejecting a CD or DVD

    Blue error screen Stop 0X0000007E (0XC0000005, 0X8070194F, 0XF78DAC30, 0XF78DA12C) and when ejecting a CD or DVD

    Said event system category 102 event 1003 error view

    Error 1000007e, parameter1, parameter 2 8070194f, parameter3, parameter4 f78da92c f78dac30 c0000005.

    Customer says that has happened for about a year.  Don't know it please help

    Hello

    Use BlueScreenView, MyEventViewer and other methods of troubleshooting BlueScreens
    See the responses in this thread - high two answers.

    http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/842fa8cf-535e-4b5d-9416-85eb31edbe6f

    ----------------------------------------------------------

    References to Vista also apply to Windows 7.

    This error (7th) is usually a driver problem and display adapter (video) driver is the most suspicious if
    It could be others. Antivirus/antispyware/security programs, major software and hardware (heat)
    questions can also cause the error. When you get to the section of the driver to use the Troubleshoot utility my
    generic methods in the next message and then return to the if necessary troubleshooting tool.

    Have you recently added hardware or drivers updated? Don't forget to look in Control Panel - Windows
    Updates to see if all drivers have been updated it. Other donor opportunities include the antivirus/anti-
    spyware/security programs.

    When you get to the pilot and sections of the memory of the troubleshooter check the following message to
    update drivers and memory test and then return to the troubleshooter if necessary.

    BCCode: 7F 0x0000007E

    Cause

    SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. TO
    interpret, you must identify which exception has been generated.

    Common exception codes are:

    0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.
    For a complete list of exception codes, see the Ntstatus.h file located in the inc directory
    the Microsoft Windows Driver Kit (WDK).

    Solve the problem
    If you do not have to debug this problem, you must use certain basic troubleshooting techniques.

    Make sure you have enough disk space.
    If a driver is identified in the bug check message, disable the driver or check with the
    Reference of the manufacturer for driver updates.
    Try changing video cards.
    Check with your hardware vendor for updates to the BIOS.
    Disable the BIOS memory options such as implementing caching or shading.
    If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2
    (the address of the exception) must identify the driver or function that caused the problem.

    If the exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system
    has been launched with the /nodebug switch... This problem should occur infrequently. If it occurs repeatedly,
    Make sure that a kernel debugger is connected and the system is booted with the/debug switch.

    In case of exception code 0 x 80000002, the trap frame provides additional information.

    If you do not know the specific cause of the exception, consider the following questions:

    Hardware incompatibility. Make sure all new hardware that is installed is listed in the
    List of Microsoft Windows Marketplace tested products.
    Service system or driver faulty device. A service driver or defective peripheral system can be
    responsible for this error. Hardware problems, such as the incompatibilities of the BIOS, memory, conflicts
    and IRQ conflicts can also generate this error.
    If a driver is listed by name in the bug check message, disable or remove that driver. Disable
    or remove drivers or services that have been recently added. If the error occurs during startup
    sequence and the system partition is formatted with the NTFS file system, you may be able to use safe
    Mode to rename or to delete the faulty driver. If the driver is used as part of the system startup procedure
    in Safe Mode, you must start the computer by using the Recovery Console to access the file.

    If the problem is associated with Win32k.sys, the source of the error may be a third remote
    control program. If this software is installed, you can remove the boot of the computer service
    by using the Recovery Console, and then by removing the offending system service file.

    Check the system log in Event Viewer for additional error messages that might help identify the
    device or the driver that generated the bug check 0x7E.

    You can also disable memory cache BIOS may try to resolve the error. You should also
    Run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system.
    For more information about these procedures, see the manual of your computer.

    The error that generates this message may occur after the first reboot during Windows Setup, or
    Once the installation is complete. A possible cause of the error is lack of disk space for installation and system
    BIOS incompatibilities. For problems during the installation of Windows that are associated with the absence of disc
    space, reduce the number of files on the disk drive hard target. Find and delete any temporary
    the files that you do not have to have files hidden Internet, backup application and .chk files files that
    contain fragments of file saved to disk scans. You can also use another hard drive with more drive
    free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.

    BCCode: 7F 0x0000007E<-- read="">
    * 1141.html? order = votes http://www.faultwire.com/solutions-fatal_error/System-thread-exception-not-HANDLED-0x0000007E-

    -------------------------------------------------------------------------

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard event viewer
    Windows. TIP - Options - Advanced filter allows you to see a time rather
    of the entire file.
    http://www.NirSoft.NET/utils/my_event_viewer.html

    Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
    info that would help. Such as ITC and 4 others entered at the bottom left. And all others
    error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during ' blue screen of the.
    death ' crashes and displays information about all accidents of a table.
    Free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by drivers of old or damaged, in particular the video drivers
    However, there are other causes.

    You can do mode if necessary safe or the Vista DVD command prompt or
    Options recovery if your system is installed by the manufacturer.

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    You can try a system restore to a point before the problem started when one exists.

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    -------------------------------------------------------------------------

    Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
    RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
    program generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Does not work
    tell all possible driver issues).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
    keyboard and mouse, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
    quit unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting, STOP error blue screen Vista
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    The Options or Vista recovery disk Startup Repair

    How to do a startup repair
    http://www.Vistax64.com/tutorials/91467-startup-repair.html

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

  • How to stop the blue e screen to start the computer and also if you try to download anything

    Remember - this is a public forum so never post private information such as numbers of mail or telephone!

    How to stop the blue e screen to start the computer and also if you try to download anything:

    • You have problems with programs
    • Error messages
    • Recent changes to your computer
    • What you have already tried to solve the problem

    Hello

    We need numbers BBCode or Code to stop the bluescreens and utilities below will help you
    provide us information. Also the methods here can help you solve the bluescreens.

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
    TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
    http://www.NirSoft.NET/utils/my_event_viewer.html

    -------------------------------------------------------------------------

    Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
    Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
    codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during "blue screen of death," collisions
    Displays information on all the "crash" of a table - free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

    You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
    system installed by the manufacturer.

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    You can try a system restore to a point before the problem started when one exists.

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    -------------------------------------------------------------------------

    Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
    smile, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting, STOP error blue screen Vista
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    The Options or Vista recovery disk Startup Repair

    How to do a startup repair
    http://www.Vistax64.com/tutorials/91467-startup-repair.html

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    I hope this helps.
    Rob - bicycle - Mark Twain said it is good.

  • HP w1907: implementation gets stuck to the 'HP invent' blue Boot Screen

    Hi all

    I have HP w1907 desktop... I use it since 2008.
    Last month I format to have the new windows 7 in it... Previously I was also working with win7 Ultimate.

    But it's keep restarting after the use of 4-5 minutes and so I installed the entire operating system yet.

    It worked very well... after 3-4 weeks, when I started it, it gets stuck at the 'HP invent' blue Boot Screen.

    This display has the instructions to enter the "Boot Menu", "Setup" and "System Recovery" by pressing key "F11" aor "Esc", "F10".  It is just there for ever.

    If I try to enter the 'Boot' Menu by pressing the 'Esc' key, I get the message "Loading Boot Menu... ", but then it hangs there forever just.  If I try to enter the "Setup" Menu, I get a similar result - it says 'enter the Setup... ". "and just hangs there.  By pressing the "F11" key does not seem to do anything.

    Any ideas on how to solve this problem?

    Searching the forums I tried to reset the BIOS - who I've got from here:

    http://h30434.www3.HP.com/T5/desktop-lockups-freezes-hangs/powering-up-gets-stuck-at-Blue-quot-HP-in...

    and

    http://support.HP.com/us-en/document/c01080282

    After doing this too, the result is null

    Please help me...

    I'm in a hurry...

    Thank you.

    Date and the incorrect time can certainly cause problems.  What happens usually, however, is that the sites Web will not be opened because the State in which the certificate is not up-to-date.  I have not heard of the time and date causing the computer does not start.  I think that you need to change the CMOS battery.  Here's a guide on how to change it.  The guide has also some good troubleshooting information.

    Once the battery has been replaced, we'll see what happens.

  • I can't launch the Skype app on my new windows laptop 8. I get a blue white screen.

    I tried to uninstall/reinstall and it worked once and now does not work again (blue white screen lanch app).

    I installed norton antivirus, but Skype has worked once when it was installed, I don't know what has changed now.

    Help, please!

    Also I'm not a computer expert so step by step instructions for a resolution are necessary :-)

    Thank you!

    I tried http://beta.skype.com/en/download-skype/skype-for-windows/ and delete the app. This desktop version works much better than the app.
    Thank you

  • Windows XP will not load past the Blue error screen

    Hi, wondering for a while if someone can help me...

    My xp system will not load past the Blue error screen that is displayed when the computer stopped suddenly or inadequate.

    No matter what are the measures that you choose to take (safe mode, the most recent configurations... etc) the system will just beyond the blue screen on the windows logo download page, where the loading bar moves about 10 seconds before returning to the blue loading page.

    So far I have tried to leave the computer as long as an unused months while I was abroad, remove the battery for varying amounts of time and leaving the computer as long as a day.

    In the absence of a recovery disk, I have no idea how to do to return to the form and would like to receive advice or suggest, keeping in mind I'm not a computer genius (if had'nt you may have guessed). Preferably, without losing my element pictures and videos stored on the hard drive, but it's just preference.

    Thank you, Jay

    Hello

    It does not seem good friend if the Windows operating system does not start even using safe mode, then I don t think you will be able to run the operating system without new OS reinstallation. :(

    To back up data from the HARD drive I recommend that you connect the internal HARD drive to external USB HDD controller and a backup of the HARD drive on another computer.

    Then you could try to reinstall the operating system on your laptop using the Toshiba Recovery CD

    See you soon

  • You can save a broken computer? My computer does NOT start after the blue hp screen.

    In the past months, my computer has been the object of a freezing randomly, and Ctrl + Alt + Delete does not work. I stopped him via the power button. Sometimes, when I start it again, the computer moniter shows nothing but a black screen and the computer sounds different when it starts normally. When this happens, I turn it off again hit the left side of the desktop and turn on again. Whenever I do this, the computer starts normally, and I go on the computer use.

    Yesterday morning, after a break of 2 days, acess my computer and it is random freezing thing once again. I force close down as one normally do, and the computer does not start and displays the same black screen and the same fan/air weird sound. I stopped him and I hit the side RIGHT this time, I think and when I turn on the computer, the usual blue HP screen appears with the establishment, boot, diagnostics and system recovery things. HOWEVER, after this screen, a black screen will appear with this weird blue symbol on the upper left corner, I have never seen this and it looks like a circle with a triangle and a Pentagon below and it remains essentially on this screen forever. When I try to hit the establishment, boot, diagnostics and the shortcuts to system recovery, on the lower left side of the screen, it says "Menu boot loading...". ' or whatever the shortcut of loading represents, but nothing ever happens. When I press the other keys, this tapping noise comes from the computer at each tap of the keyboard.

    I have no idea what to do, and at this point, my first priority is to save important files on the computer. Does anyone know what is the problem? I want her more than a problem of system rather than a virus problem because refusing the boot black screen thing lasts for years. My computer is 3-4 years. I enclose a sketch of what looks like the weird symbol.

    MY COMPUTER WORKS NOW!

    With the flash drive, I was able to access the BIOS, which before, I couldn't.

    Eventually my computer was in some strange sort of lockdown setting, I switched it back to activate and now its work! I remember save important things in the future. Thank you very much for your help!

  • When I try to open windows media center my Blue computer screen and my computer stops

    When I try to open windows media center my Blue computer screen and my computer stops

    Hello

    More that might help.

    Check this thread for more information using BlueScreenView, MyEventViewer and other methods
    to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

    http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/c675b7b8-795f-474d-a1c4-6b77b3fcd990

    We can analyze the minidumps if make you it available to the SkyDrive or another file
    sharing sites.

    ZIP or download the content of the C:\Windows\minidump

    Use SkyDrive to upload collected files
    http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

    -------------------------------------------------------------------------

    Also this, so you can see the probable bluescreens.

    Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
    (also Windows 7)
    http://www.winvistatips.com/disable-automatic-restart-T84.html

    ===========================================================

    Check out these utilities to see if information may be collected:

    It is an excellent tool for displaying the blue screen error information

    -Free - BlueScreenView scans all your minidump files created during 'blue screen of death '.
    hangs and displays information about all accidents of a table.
    http://www.NirSoft.NET/utils/blue_screen_view.html

    -------------

    MyEventViewer can be verified at the time of the blue screen (BSOD) within a second or
    so time of the BSOD for more information on the possible cause - see TIP.

    MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
    TIP - Options - Advanced filter allows you to see a period of time instead of the whole of the record-
    Set it for a bit before and after the time of the BSOD.
    http://www.NirSoft.NET/utils/my_event_viewer.html

    ------------

    AppCrashView - free - a small utility for Windows Vista and Windows 7 which shows the
    Details of all application crashes occurred in your system. The information of the plant are extracted
    the .wer files created by the Windows Error Reporting (WER) of exploitation component
    system each time that an accident has occurred. AppCrashView also allows you to easily record the
    list of accidents to the text/html/csv/xml file.
    http://www.NirSoft.NET/utils/app_crash_view.html

    I hope this helps.

Maybe you are looking for

  • Not able to see the semi colon and comma when sending email

    Hello I am not able to see the semi colon and comma everything by typing the e-mail address to "TO" However in the body of the email, I'm able to see. Thank you Rakesh K *. ***********

  • Diagnostic startup

    problems with the screen it seems to freeze. Compaq SR5510F Office Rolled up on diagnostics at boot seems sometme it freezes when you perform the memory check so next time is seems ok displays the check disk HARD control of CD/DVD and then open Windo

  • 0x800706be error code

    reason of not not downloading a branch identified that could allow a tie remote no authenticated understand your system and take control etc, but when I returned to day I don't see this update are displayed

  • I've upgraded from vista home premium to windows 7 Professional and had to do a custom installation

    I've upgraded from vista home premium to windows 7 Professional and had to do an installation custom and lost all my Hp software, HP Advisior, PC doctor among others. Is there a way to get them without reinstalling everything again

  • Error Disk WDC - WD5000BEVT - 60ZAT0 ATA Device Volume C:\;D:\

    Hello world I hope there, can someone help me.  Yesterday, a microsoft error message appeared on my laptop, which is a HP Pavilion DV5-1203em.  The message says that my hard disk appears to be damaged and they recommended I have immediately back up a