Is compatible with BNC-2090 PCI-6723 has?

Similar Questions

• PCI 6221 with BNC-2090 acquisition card

  
  

  Hello

  With regard to connectivity, here is the user manual of the BNC-2090:
  http://www.NI.com/PDF/manuals/321183a.PDF

  Explanations of the it there all pour a measure differential, CSR or NRSE and how to put the switches pour different modus.
  In Chapter 2 it is also the comment explanation connect inputs and outputs signals.

  Nice day
  Ken

• Latitude C640 with 1470 mini pci wifi has very low signal strength

  I just installed 1470 broadcom mini pci card with the 4.10.40.0 (from decompression R115321.exe) on a Dell Latitude C640 driver version.

  The card sees the network and connects, but I must be withinn 5 feet from the router, and even in this case the signal is 'Very low' (an or maybe 2 bars). I can communicate with various other wireless cards on other laptops with the full signal strength during the major part of the House.

  Why the intensity of the signal would be so bad?

  Is the 1470 is not very sensitive? the driver is bad for my setup? is there an INCOMPATIBILITY between the 1470 and the DLink DI-524 router? Is this an indication that the antenna on my wifi card is damaged? (I got it on ebay)

  Any help would be greatly appreciated.

  Thank you.

  Latitude C640

  Windows XP SP3

  Wireless 1470 mini pci card

  connected to the Dlink-524 (firmware 1.11) wireless router using WPA - PSK encryption

  
  

• square pulse generated with the NI PCI-6723

  Hello

  I generated a pulse biphasic square in Labview using a standard square wave generator and by stopping the vi to run after generating a full periodic square wave period. The only problem I have is that as soon as I stop my code, so once the square impulse had emerged, the analog output of the Council NOR remains at the same voltage as the last sample of the generated square pulse. Instead, I'd like the voltage is back to zero.

  This is the same phenomenon that you see when you use the Measurement & Automation when you build an analog output and then you stop manually, if you take a look with an oscilloscope to output voltage, that it remains at the level you stopped analog signal.

  I have attached a picture of a pulse square with 1V amplitude and 1250 Hz frequency showing that voltage level will not return to zero. If I try to add a sample more to the curve above, the tension instantly bumps up to 1, leaving me with the same problem.

  Any thoughts?

  Thank you

  Alessandro

  It should work.

• 24 e / s digital on the grid of the BNC-2090 a mount.

  Hi all

  I use a capture card of data NI PCI-6221 connected to a BNC-2090 rack mounting has. Digital I/O Terminal block on the rack mounting sping is a watch the bottom of the image. The PCI-6221 card has 3 digital i/o ports with 8 lines for each port. I tested what line corresponds to what terminal and came up with the following representation in red, where, for example, the P2-2 corresponds to the Port 2 - line 2, etc. However, it seems that Port 1 - 0 line is not represented by a sping terminals.

  Is it possible to get an e/s on support for this particular line mounting while I have available altogether instead of only 23 24 lines? Any suggestions would be really appreciated.

  Hello

  I think you are right that the PFI0 line is not represented by one of the terminals of the spring.  Sounds more like it is represented by a BNC connector.  You can see that on page 2-1 Manual BNC-2090 is:

  http://www.NI.com/PDF/manuals/372101a.PDF

• How to check if my MBP is compatible with SSD?

  Can you please help me to know if the motherboard of my MacBook Pro is compatible with SSD? I'm on MacBook Pro (15-inch, mid-2012)

  It is compatible with any SSD if it has a HARD drive. If it came with built-in SSD so it is not extensible. In this case, you should check with OWC for possible improvements.

• TestStand 2013 is compatible with Visual Studio 2013?

  TestStand 2013 is compatible with Visual Studio 2013?  Has anyone used together?

  Code modules you build should be compatible/executables, however integration between TestStand and Visual Studio 2013 (for help debugging and development, for example the code patterns, step in the input/output between TestStand and Visual Studio and includes the updated paths automatically in Visual Studio) may not work correctly in all cases since Visual Studio 2013 is out after 2013 TestStand.

  My understanding is that most of the things do not work, a few known minor issues are integration of help file does not and TestStand to what version of Visual Studio, the projects that you specify for the source of a specification of the step code section are not recognize.

  Hope this helps,

  -Doug

• I want to know if graphics PNY GeForce GTX 650 VCGGTX6501XPB compatible with desktop video card Aspire M3450?

  Hello

  I have an Acer Aspire M3450 Office (processor Quad-Core AMD FX (tm) - 4100 (4 CPUs), ~3.6GHz) and intend to install a card PNY GeForce GTX 650 video VCGGTX6501XPB (1 GB GDDR5, PCI-Express 3.0(x16), 1 x Dual-link DVI - D, 1 x Dual-link DVI - I, 1 x Mini-HDMI, DirectX 11, Dual-Slot). I want to know whether the video card that is compatible with my computer, PCI E slot, existing supply etc.,.

  For comments and suggestions please. Thank you and good day to all.

  Kudrow888

  Hello

  the GPU you prefer, I'm not a reson for why it's not compatible. Just check with power supply to your turn, if I'm not mistaken, the power supply to your turn would be 500W, if so you are good to go.

• Which cameras are compatible with the capture feature in adobe first pro?

  My son made videos of stop motion and wants to be able to use the capture feature on adobe first pro where you connect your camera via USB and can capture images on your computer through your camera. I am looking to buy him a camera and trying to find a list of digital cameras are compatible with this feature, it now has a small camera fuji who will not let him do.

  What other users have said is correct. First capture via FireWire or SDI/HDMI through a solution of part 3.

  For your situation, I would say the better is to connect the device to your computer via USB or use a card reader and copy the directory on your hard drive and interfere in first via media browser.

  If you Google "how to do stop motion in first pro" there are tons of tutorials.

  Best,

  Peter Garaway

  Adobe

  Premiere Pro

• DI/O cards such as the 651 x are compatible with PCIe 1 x?

  Hello

  This can be a bit of a stupid question, but it's my first outing with NEITHER and yet I somehow received some amount of responsibility for a very strange procurement process.  I hope the question is easy to answer and that will mitigate its possible idiocy.

  Are maps such as the NI 651 x (http://www.ni.com/datasheet/pdf/en/ds-105) compatible with PCIe 1 x?  Of the image, it looks like they are designed to run on PCIe 16 x, but since the speed is not a major concern, that I wondered if she settle and operate normally on PCIe 1 x.

  I am limited in contracts with a default value, extensive construction of tower PC organization, whose mother has two PCIe 16 x and two PCIe 1 x.  Since I will probably need three cards, I was hoping that it would be compatible with the PCIe 1 x slot and we would save the hassle of special purchase order form.

  Thanks for any help!

  N ° it is even not a PCIe connection.  It's PCI.  I recommend that you call your local representative of OR discuss your needs and they can help steer you in the right direction.

• Card PCI-6259 is compatible with the Dell Precision 390?

  Hi all

  I need help in answering this question.  I want to buy a better computer for my data PCI-6259 acquisition card.  I tried to search to see if the card is compatible with the PC and there's previous numbers with this set-up before other users.  Do you have a link to the list of the DAQ cards with tested PC configurations?  I want to just make sure that when I buy the computer, everything will work without problem because I only have one shot at this.

  Thanks to all in advance.

  Kind regards

  justdomechanicalengineering

  Hello

  We do not have a link to specific DAQ board/PC pairings, but the specifications for the Dell Precision 360 indicate that she has three ports PCI 5V which must be compatible with your PCI-6259.

  Best,

  Dan Nelson

  Technical sales engineer

• Firefox worked, today has not started with the error the version of this file is not compatible with the version of windows you are using.

  Computer is Windows 7 Ultimate 64 bit. Firefox has work fine for over a year on this computer. Nothing has been changed or updated updated except Windows update indicates that it installed updates on August 19. I had computer week before because only out of town, back entrance and began August 18, but Firefox has worked that day. Does not use FF again until today. Today August 22, firefox does not start, shortcut icon changed program not there. Exe in the folder when you click Poster error message says the version of this file is not compatible with the version of Windows, I am running. Exe of Firefox shows created on 20 August. I suspect the update, Windows or FF but lean towards windows, which was spent, who broke things. I noticed that IE 10 updates, updates of .NET framework and the malicious software removal tool have been installed. I tried to restart the computer, has not set. Tried to run as administrator, did not work. I don't want to uninstall FF, at least have to because of all the things I have here, bookmarks, last past passwords, etc..

  Hello

  Some Firefox problems can be solved by performing a clean reinstall. This means that you remove Firefox program files (not the profile folder, where the bookmarks are stored) and then reinstall Firefox. Please follow these steps:

  Note: You can print these steps or consult them in another browser.

  1. Download the latest version of Firefox from http://www.mozilla.org office and save the installer to your computer.
  2. Once the download is complete, close all Firefox Windows (click on quit in the file menu or Firefox).
  3. Remove the Firefox installation folder, which is located in one of these locations, by default:
     • Windows:
       • C:\Program Files\Mozilla Firefox
       • C:\Program Files (x 86) \Mozilla Firefox
     • Mac: Delete Firefox in the Applications folder.
     • Linux: If you have installed Firefox with the distribution-based package manager, you must use the same way to uninstall: see Install Firefox on Linux. If you have downloaded and installed the binary package from the Firefox download page, simply remove the folder firefox in your home directory.
  4. Now, go ahead and reinstall Firefox:
     1. Double-click on the downloaded Setup file and go through the steps in the installation wizard.
     2. Once the wizard is completed, click to open Firefox directly after clicking the Finish button.

  Please report back to see if this helped you!

  Thank you.

• Windows 10 is not compatible with genie, someone has ACTUALLY a solution?

  I just updated my computer laptop microsoft Windows 10 because I was stuck with 8.1 for so long, super happy until I went to redownload genius because it deleted a little after the update, and now it is not even freaking work with windows 10. The new SUCKS update because it is not compatible with the latest technology for windows... is there actual patches? I went through the discussion after discussion and nothing really works or it is not found. Help!

  Hi @skunkylouou,

  We apologize for the inconvenience, as the cause of the problem has been just recently discovered. Rest assured, we are working on a fix for future updates. Have you tried the temporary work around? If this isn't the case, you can follow the steps below.

  1. install the latest version of NETGEAR genius. You can use the below download link.

  http://Netgear.com/Home/Discover/apps/genie.aspx

  2. Once you have successfully installed the program, go to C:\Program Files (x 86) \NETGEAR Genie\bin

  3. remove the drivers folder.

  4 download the drivers from the previous version of NETGEAR engineering using the below download link.

  https://drive.Google.com/file/d/0Bz-pjmQaYmk6bEVUbmxtUTY0MW8/view?USP=sharing

  5 unzip the file to your favorite place (Office would be easy to locate). It will contain the drivers folder.

  6 copy the drivers folder you have just unpacked and navigate to C:\Program Files (x 86) \NETGEAR Genie\bin

  7 paste the folder drivers.

  8 restart the genius of NETGEAR program

  Kind regards

  Dexter

  The community team

• I have an Iomega external HD model MDHD320-T. It has been used on an older Mac OX9 Office running. Can I access data on this disc hard by downloading a software compatible with my current Mac OS Yosemite? Thank you! George

  I have an Iomega external HD model MDHD320-T.

  It has been used on an older Mac OX9 Office running.

  Can I access data on this disc hard by downloading a software compatible with my current Mac OS Yosemite?

  Also, I find no other than ads Iomega site.

  Are they still in business?

  Thank you!

  George

  Search Wikipedia for LenovaEMC.

  The chances of finding software are slim to none.

• Create a waveform using PCI-6723 AO with various time intervals on the trailing edge of the sample of 200 Hz clock and 0.1% duty cycle

  I use the PCI-6723 card and I am trying to produce a model of waveform using the analog output channel. The wave consists of 5 different voltage levels. The main problem is that the first 4 voltage levels are supposed to have 926 microseconds time intervals and the time interval the last voltage level is supposed to be 1,296 milliseconds. In addition, the waveform must be triggered on the trailing edge of a sample clock of 200 Hz with a 0.1% Duty Cycle. Is it still possible? If so, any help would be greatly appreciated. Thanks in advance!

  Here is what I currently have, but it does not fulfill my purpose.

   int32   written;
      float64 data[5] = {-0.23, 0.38, 1.12, 1.78, 0.10};  //volts
      //long  time[5] = {  926,  926,  926,  926, 1296};  //microseconds
  
      // DAQmx Configure Clock
      DAQmxErrChk (DAQmxCreateTask("",&taskHandleFRQ));
      DAQmxErrChk (DAQmxCreateCOPulseChanFreq(taskHandleFRQ,"Dev3/ctr0","",DAQmx_Val_Hz,DAQmx_Val_Low,0,200,0.001));
      DAQmxErrChk (DAQmxCfgImplicitTiming(taskHandleFRQ,DAQmx_Val_ContSamps,1));
  
      // DAQmx Start Code
      DAQmxErrChk (DAQmxStartTask(taskHandleFRQ));
  
      // DAQmx Configure Code
      DAQmxErrChk (DAQmxCreateTask("",&taskHandle));
      DAQmxErrChk (DAQmxCreateAOVoltageChan(taskHandle,"Dev3/ao0","",-10.0,10.0,DAQmx_Val_Volts,NULL));
      DAQmxErrChk (DAQmxCfgSampClkTiming(taskHandle,"/Dev3/Ctr0Out",1000.0,DAQmx_Val_Falling,DAQmx_Val_ContSamps,5));
  
      // DAQmx Write Code
      DAQmxErrChk (DAQmxWriteAnalogF64(taskHandle,5,0,10.0,DAQmx_Val_GroupByChannel,data,&written,NULL));
  
      // DAQmx Start Code
      DAQmxErrChk (DAQmxStartTask(taskHandle));
  

  Bingo. This code seems to work much better. Looks like I had to reduce my number of samples per 1 to fit the waveform desired in 5 milliseconds of the sample clock delay.

  However, if someone knows a better way to achieve these results, I am open to all ideas.

  void CDevDlg::OnRdr1e1()
  {
      float64     data[4000];
      float64     volt[5] = {-0.23, 0.38, 1.12, 1.78, 0.10};  //volts
      int x=0,d;
  
      for(int v=0; v<4; v++)
      {
          for(d=0; d<741; d++)
          {
              data[x++] = volt[v];
          }
      }
      for(d=0; d<1036; d++)
      {
          data[x++] = volt[4];
      }
  
      // DAQmx Configure Clock
      DAQmxErrChk (DAQmxCreateTask("",&taskHandleFRQ));
      DAQmxErrChk (DAQmxCreateCOPulseChanFreq(taskHandleFRQ,"Dev3/ctr0","",DAQmx_Val_Hz,DAQmx_Val_Low,0,200,0.001));
      DAQmxErrChk (DAQmxCfgImplicitTiming(taskHandleFRQ,DAQmx_Val_ContSamps,800000));
  
      // DAQmx Start Code
      DAQmxErrChk (DAQmxStartTask(taskHandleFRQ));
  
      // DAQmx Configure Code
      DAQmxErrChk (DAQmxCreateTask("",&taskHandle));
      DAQmxErrChk (DAQmxCreateAOVoltageChan(taskHandle,"Dev3/ao0","",-0.5,2.0,DAQmx_Val_Volts,NULL));
      DAQmxErrChk (DAQmxCfgSampClkTiming(taskHandle,"",800000,DAQmx_Val_Rising,DAQmx_Val_ContSamps,4000));
      DAQmxErrChk (DAQmxCfgDigEdgeStartTrig(taskHandle,"/Dev3/Ctr0Out",DAQmx_Val_Falling));
  
      // DAQmx Write Code
      DAQmxErrChk (DAQmxWriteAnalogF64(taskHandle,4000,1,10.0,DAQmx_Val_GroupByChannel,data,NULL,NULL));
  }