is daq bit resolution applied to the area defined in the daq assistant or well to the limits of physical blood of the daq hardware.

Similar Questions

• That means the 14-bit resolution

  Hello

  The '14-bit resolution' refers to the data entry for the PXI-5412 (via niFgen_CreateWaveformFromFileI16 or niFgen_CreateWaveformFromFileF64), the output of the PXI-5412 through channel 0, or both?  To clarify a bit, I know that niFgen_CreateWaveformFromFileI16 reads a 16-bit data source values, but the values contained in these 16 bits must be within a range of 14-bit?

  Some background information...  I use a system that contains a PXI-5412.  I am executing the example C code and change it to some arbitrary waveforms.  I have a Spectrum Analyzer, connected to the output of the PXI-5412 and tries to understand the results.  I use a data file that contains a chirp waveform.

  Generate data of chirp via Matlab.  I can save try it in different formats, but began to record off the coast under 16-bit.  In my application, I load the data using niFgen_CreateWaveformFromFileI16 and start the generation.  The output is fed to a Spectrum Analyzer, but the result doesn't look like a sizzle.  However, if I record the same data on as a double and use the SAME code (do NOT change the niFgen_CreateWaveformFromFileI16 function), I see a Twitter.  This result leads me to my question.

  Moreover, it is in the talk discussion page wrong forum.  You must go to the site below next time:

  http://forums.NI.com/T5/signal-generators/BD-p/310

  Thank you

• How can I click apply when switching back resolution lower when the window does not display the Apply button when

  How can I click apply when lower resolution when the window does not display the button apply because the resolution is too low

  Hello

  Try pressing the ENTER key on the keyboard instead.

  See you soon.

• NSX 6.1.5 - distribute Firewall rules are not applied to the empty virtual switches

  Hi all

  We have a big problem since we have improved the NSX to version 6.1.3 to 6.1.5.

  I get a bug following this procedure:

  . In vSphere Client--> NSX, create a new virtual switch

  . Distribuer distribute the firewall, create a rule to deny traffic between two survey periods. Example: source: all, destination: all, service: all, Action: reject, applies: the new virtual switch

  . Connect two VMS to the virtual switch and you can test the other (this is false due to the firewall rule)

  . Publish ANY changes on the firewall distribute (could not be related to our rule. Example to change its name to another rule), and the rule starts to operate.

  Additional steps:

  . Remove the firewall rule

  . Identify the virtual machines in the virtual switch

  . Re-create the firewall with applies rule: the virtual switch (still empty)

  . Connect the virtual machines and ping between them. Yet once, the rule does not work.

  . Publish ANY changes on distributed firewalls and the rule starts to operate.

  NSX version 6.1.3 and 6.2.0 both work correctly. But I can't downgrade to 6.1.3 or upgrade to 6.2.0. 6.2.1 upgrade involves the upgrade of several other components.

  I use the following versions:

  . NSX 6.1.5

  . vCenter Version 5.5.0 Build 2414847

  . ESXi, 5.5.0, 2718055

  Please, any ideas?

  Thank you very much

  D.

  She seems to be a bug in 6.1.5 NSX and there is no solution for this yet. There are workarounds, but none of them apply to my "fully automated" environment

  We need to wait for a fix or upgrade to NSX 6.2.1 requiring an upgrade of several components as well.

  D.

• How to set the sampling interval using DAQ hardware?

  Now I have a sensor capability and hardware DAQ 24 bit (http://www.mccdaq.com/usb-data-acquisition/USB-2404-10.aspx).

  The DAQ hardware has the 50kS/s maximum sampling rate. My question is how to define the range of data collection. For example, if I set the sampling rate of 2000, continuous sample mode, I use read.vi DAQmx in a while loop and set the "number of samples per channel" to 100. I want to plot these data over time using a XY Chart and also save this data. So I add a 'Medium' function to get the average of 100 samples per each loop (medium, there are 20 release of data per second). But when I put a 'number of samples per channel' much more small (for more data per second), there are a few problems. It seems that the program cannot read the data as much and get the average at a higher frequency. I don't know where is the problem. Overall, the collection of data more frequently? Maybe I didn't articulate my question. I'll upload a simple program later if necessary. Thank you.

  
  

• application works well on windows 7 32 bit OS. But the same application crashes on windows 7 64 bit OS

  Hi all

  We have installed a software called eVision on our windows 7 32-bit operating system. The application works well.

  We installed the same software eVision on our windows 7 64-bit OS systems. We could install the software correctly. But when we opened the application, the breaks down after a few minutes. We see the error below. What is happening on all the 64 bit OS.  So there must be something to do with the 64 bit OS. We addressed this issue in favour of the seller. But we have received no resolution. Please help us solve this issue.

  Error:

  spEDI.exe has stopped responding...

  Thank you
  Srinu

  What version of software is this? Is it designed for Windows 7 or earlier?

  It is possible it could 16-bit components why it worked on 32-bit Windows 7.

  You could try to install in Windows 7 64-bit compatibility mode.

  Pointer pointing to the installation for eVision files, right-click on the Setup, and then click Properties

  Select the Compatibility tab then a known version of Windows in which the software works or is designed to:

  

  Click apply then OK

• Sharing won't apply to the Apple store? How fresh Spotify my sister by charging me by iCloud family shares?

  The sharing of family purchase don't apply to the Apple store? How fresh Spotify my sister by charging me by iCloud family shares? And without notification, or by e-mail.

  Say you that you be billed for the purchase of your sister? If it is then see the page that you have published since:

  After you set up your family, anytime a family member throws a new purchase, that it will be charged directly to your account, unless the family member has gift or store credit. First of all, their store credit will be used to pay the invoice total or partial. The rest will be billed to the card of the family of the Organizer. The family Organizer, the revenue generated by the transaction will be sent to you. Learn more about how are charged purchases made on iTunes Store.

• Premium never applied to the Messenger

  I got a bonus today. I restarted. Reinstalled. Registered. Pretty much done everything I could.

  The Messenger never gets applied premium status.

  No support appellant's group. Even if another Member of the Group call it.

  Ads remain visible even if my account disabled them via the premium (via the account Web page Panel)

  Page Web says to his credit.

  It does not apply to the customer no matter what I do to it.

  If you use the 'modern' (metro) Skype for Windows 8, then you know that group video calls are not supported on this Skype application.

  If you want to be able to make video calls to group then you need to install the desktop version.

  The currently most recent Skype 6.11.0.102 desktop version can be installed using the msi installer:

  http://download.Skype.com/MSI/SkypeSetup_6.11.0.102.msi

• Tecra P11 - No Windows 7 64-bit display driver on the Toshiba site

  Hello

  I just got a new laptop today and installed Windows 7 64-bit. Looking at the website of Toshiba (win 7 page) I discovered that there are no drivers listed for the P11. Given that my laptop came with a Windows 7 license I at least expect that Windows 7 drivers would be on the Page of the Toshiba Support. If someone could post a link that would be greatly appreciated.

  Thank you

  I ve checked page Australian support and drivers Win7 does not exist, yet.
  To be honest this Tecra is unknown to me, but if you have newer model laptop, I assume that all of the drivers, tools, and utilities will soon be available. There is no other connection.

  I m wondering you did not check the support page before you do a clean install.
  By the way: this license key, activations belongs to delivered version Win7 and you cannot use it for the installation of the operating system with the Microsoft installation disc.

• Diffenernce / choice between using a shielded connection block (2120 BNC) or the DAQ hardware?

  Hello

  We build a new configuration of lab that will need hardware in the loop detection by sensors data and formatting / analysis using programs and possibly return data in material for the control.

  We are confused that the connection block shielded BNC (who has the outputs and analog inputs / digital) or a DAQ hardware for can be used?

  What are the main differences between them?

  shed light on the above is very appreciated...

  Best regards

  FESMI

  FESMI wrote:

  We are confused that the connection block shielded BNC (who has the outputs and analog inputs / digital) or a DAQ hardware for can be used?

  Data acquisition is what is the real measure of the signals.  The Terminal is just a simple way to route signals for data acquisition.  If you can actually the terminal box, cable and card DAQ.

  I highly recommend talking to your representative local sales OR to make sure that you get exactly what you need.

• Problems of bit shift left in the node of the formula

  Hello

  Sorry, but my English is not good.

  I am trying to run a bit left SHIFT in the node of the formula, but the left SHIFT does not work as I expected.

  uInt32 parametro[5];
  float32 valorAmostra;
  int16 indiceAmostra;
  uInt8 indiceResposta;
  int16 controle;
  int32 valor;
  int8 i;
  
  for(i=0; i<5; i++)
      parametro[i]=param[i];
  
  valor = parametro[5]<<16 | parametro[4]<<8 | parametro[3];
  controle = parametro[1]<<8 | parametro[0];
  
  indiceAmostra = (controle & 0x3FF);
  indiceResposta = (controle >> 10);
  
  valorAmostra = valor & 0x7FFFFF;
  valorAmostra = valorAmostra*(2.4/8388607);
  
     if((valor & 0x800000) == 0x800000)
        valorAmostra = valorAmostra*(-1);
  

  the input param array is uInt8 type, because I saw in other topics that does not move with uInt8,

  I copy the values in the array param to parameter , which is of type uInt32, but still does not work.

  Test the input parameter with the following values:

  [] param = {10,14,10,0,16}

  the returned valorAmostra is 0,00117188 then it should be 0,300003.

  Can someone help me please?

  Portuguese:

  OLA,

  Is um no bug no LabVIEW para esta operacao. Este bug devera ser corrigido em paid futuras. UMA Solução para esta down e use int32 ao investment of um ulnt32 um.

  Any doubt please between let em.

  Obrigado.

  English:

   

  I studied the problem you are having, and it turns out that this is a bug that has already been reported and documented. The work around is to use int32 instead of uInt32.

  Thank you.

• error-5093 "the analysis library is not found" in the 64-bit project. But the analysis library is located in the 32-bit project

  Hello

  I use the system of Labwindows/CVI 2010 full development in a Windows 7 Professional 64-bit computer. Thus, the analysis library is installed (see the attached file) and the analysis of the options to customize menu library is selected.

  I use several function analysis library (WhiteNoise, MaxMin1D, LinFit, etc.). 32-bit projects work very well. 64-bit project there is not link error, the exe file is created, but there are errors like this:

  Function WhiteNoise: (return value is 5093 [0xffffffffffffec1b]). The analysis DLL library is not found or cannot be loaded.

  Ditto for the other functions of analysis library.

  How to use the analysis in 64-bit projects library, is the library of analysis 64 bit compatible?

  Thanks in advance

  Hi DansatB,

  Thank you for posting on this forum!

  Yes, the advanced analysis library is 64-bit capable. I can do the test on my computer the CVI 2013.

  I think it'll be great correctly uninstall your version CVI all ANS reinstall.

  Concerning

• We can connect the output of the sensor directly to the DAQ hardware or any interface necessary?

  We can connect the output of the sensor directly to the DAQ hardware or any interface necessary? If so wat kinda necessary interface?

  How to change the sensor output to match entry-level data acquisition?

  If the sensor output beyond daq range is provided. What are its effects? pls answer

  -It depends on your signal and the type of device you have. Your DAQ provides a package of signals? Also, what type of signal you want to measure? You must select DAQ that matches that. Take a look at the following before you start:

  Getting started with NO-DAQmx: Main Page

  And take a look at table 1 in the following article to wire your signal to the right:

  Wiring and considerations of noise for analog signals

  -You will need to use external circuitory to match the input of data acquisition range.

  -You could damage the unit.

  If you have any other questions, please after return. And, don't forget to give more details about your configuration, the hardware and what you're trying to do.

• upgrade to Windows 7 64 bit Ultimate Edition with the new installation of windows XP

  I plan to upgrade to Windows 7 64 bit Ultimate Edition with the new installation of windows XP

  my PC configuration is like below:

  Card mother Intel DH61WW
  Processor Core I3 2100 3.1 Ghz
  4 GB OF DDR3 RAM
  Seagate 1 TB SATA HARD drive
  OS: Microsoft Windows XP Professional SP3

  I run Windows 7 upgrade advisor in which some results below the incompatibilities:

  Intel (r) 6 Series / C200 Series Chipset Family SMBus Controller - 1 22
  Unknown Intel we have not the compatibility information about this device.
  Intel 82579V Gigabit Network Connection
  Unknown Intel we have not the compatibility information about this device.
  Realtek High Definition Audio
  Realtek unknown we have not the compatibility information about this device.

  Here's my conceerns:

  What needs to be done to overcome the problems of incompatibility?
  Do I need to download new software files compatible for windows 7 and then install
  for example VLC media player, Skype, MySQL Server I am running
  or currently existing files are compatible to install with Windows 7?

  Would I be able to upgrade to windows 7 without any problem and safely?

  Could you please help me with the questions above?

  Please correct me with additional suggetions that I may have missed with.

  Looking forward to hear from you

  Thank you

  You understand that you will not be able to upgrade Windows XP to Windows 7?  He will have to do a clean install.

  The Council supports Windows 7, you can get the drivers here (the chipset drivers should be the first drivers you install after installing the operating system.)

  John

• Determine the number of traditional DAQ hardware using Labview.

  Hello

  Anyone can answer the question:

  Regarding materials traditional DAQ, for example the DMM OR-4060, how

  can I programmatically determine the number of device which can be seen in MAX?

  With the help of Labview 8.5, I looked into the following function libraries:

  NOR-DMM

  VISA

  NOR-ModInst

  None of the libraries above seem to provide access the number of traditional DAQ hardware

  property, which is automatically assigned.

  Background:

  I have a 18 PXI chassis containing 2 DMM, in housing 3 and 14.

  The DMM may be a mixture of type OR-4060 or NOR-4070.

  The system is controlled by a Teststand sequence employing IVI - DMM

  steps.

  When you set the IVI logical name step, I am referring to IVI device defined Sessions

  Max - rutime determined.

  Labview VISA functions using I can determine the model, i.e. 4060 or 4070.

  Because the DMM just locate into the slots 3 or 14, then the devices NOR-4070

  are accessible using the following descriptors of resources: PXI1Slot3 or

  PXISlot14.

  (The 4070 is compatible DAQmX.)

  So for devices OR-4070, I can predefine 2 Sessions of IVI device, knowing

  It will be sufficient for all occasions, when I run my Teststand sequence, which will be

  determine what device session to use at run time.

  But I'm stuck for the NOR-4060.

  At the Session of the device, I have to give a descriptor of resource the following

  format: DAQ::x (where x is the device number)

  I could create device 18 sessions each reference to a different DAQ::x, but to select

  the good pair during execution, I would need to programmatically determine the device

  number, i.e. the value of x.

  Where my question.

  The closest I came to a solution was an entry of the Knowledge Base that said that the

  Assigned device number would be the same as the slot number, providing the

  Number of the device had not previously configured manually.

  Unfortunately, our device numbers have been changed manually and maybe in the future.

  All popular solutions.

  Gary.

  Hi Gary,.

  Good afternoon and I hope that your well today.

  Thanks for your post and I want to help you solve your problems.

  I don't think there is just a function that you can use to identify and collect information on all cards with your. For traditional DAQ devices in particular I suggest using the Information.vi of DAQ devices get.

  If you look at this link,

  SAL posted an example VI entitled, find dev trad.vi.

  You can get information such as serial number, Dev name and the Base address.

  The assistance of the respective drivers to collect information you could generate an array of strings with the information that you need all the slots.

  Please let me know if this is useful at all,