Is it possible for the EPA use for an exisiting LAN wireless access point?

Similar Questions

• WRV200 as for xbox wireless access point

  I have a WRGT54GX2 that runs my home network. I have a Xbox 360 in another room. Can I use an WRV200 router as an access point wireless connects to the xbox360, which gets its information from the WRGT54GX2. Just see if it's possible before you buy the xbox wireless adapter.

  Ok thank you...

  stop at the store, I'll

• Errror: The certificate chain was issued by an authority that is not approved. connecting to a wireless access point

  I can't understand the process of certificates, by connecting a pc wireless access point that is authenticated by the radius server, im keep having this error "the certificate chain was issued by an authority that is not approved." do I need to set a certificate on the pc?

  Hello

  1. What is the version of the operating system that you are using?

  2. What is the exact full error message?

  If you use Windows 7 follow the link below:

  http://Windows.Microsoft.com/en-us/Windows7/view-or-manage-your-certificates

  http://Windows.Microsoft.com/en-us/Windows7/certificates-frequently-asked-questions

  You can also contact your ISP for more information.

  Hope the above information is helpful.

• A WRT160N V3 can be used as wireless access point.

  I have an AT & T's broadband router.  A WRT160N is connected, so I now have Wireless N capabilities.  I have a second WRT160N I want to put in my living room as a point of access, so I can connect my BluRay player and video stream.  How can I configure the second WRT160N as access point?

  Thank you in advance,

  Andrew

  Topic 1. Yes, you can use your second WRT and put in place as a second access point to your network. First of all, unplug the second WRT to your network and wire a computer in one of its LAN ports. Open the web interface at http://192.168.1.1/ on the main configuration page, change the address LAN IP of 192.168.1.1 to 192.168.1.2 and disable the DHCP server. Save the settings. Unplug the computer and connect the cable to the first router on one of the second router's LAN ports. Do not use the internet port of the second router! Now you can use the wireless access point in the second router as access point additional for your network.

  For a wireless roaming the two Wrds with identical wireless settings (SSID, wireless security, etc.) and don't forget to enable the SSID broadcast. Only the channel assignments should be different. Different channels spaced at least 5 avoids duplication of canals. Now your laptop can connect to your network via either WRT and internet through the first WRT. It must also be able to move between the two Wrds without losing the connection.

  Re 2. Because the WRT160N has only the ethernet 10/100 ports a CAT5e cable should do. Of course, you can consider getting a better cable, for example a cat6 for future enhancements to your network. It depends on how much effort it is necessary to replace the cable later if you decide to go for gigabit ethernet on your local network.

• The connection between your cable modem, router or access point, and Internet are broken.

  What is the average message "the connection between your cable modum, router or access point, and internet are broken" and how to fix it?  We use internet provider time warner.  Can I access online using mini jetpack, but not through time warner.  Is the problem with our internet service or hardware problem?

  Hello Terri,

  Thanks for posting your question on the Microsoft community.

  Thank you for details on the issue.

  This problem may occur because of damaged or incorrect network settings.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run the network troubleshooting and check.
  Reference:
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Note: You can run utilities times 'Internet connection' and 'network card'.

  If this does not help, use method 2.

  Method 2:
  Reset TCP/IP and check the issue.
  Refer to this article:
  How to reset TCP/IP using the NetShell utility
  https://support.Microsoft.com/en-us/KB/299357

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• After running Thinkvantage System Update, unable to connect the wireless access point

  I've recently performed Thinkvantage System update for updating various programs/drivers on my T61p.  I've updated the V5.12 access connections.  In addition to this I was required to update driver V1.52 power management and functionality of the shortcut key for

  V2.10.0002 (two of them were the most recent available).

  After these updates, I can connect is no longer to any access point wireless that worked before this update.  I have tried to reinstall earlier versions of Access Connections, but still couldn't connect to wireless access points.

  ANY help would be appreciated.

  OK, problem solved.  I found that when I ran last weekend system update downloaded and installed an incorrect driver for my wireless hardware.  I installed the correct driver and now the connection to a wireless access point works.

  Certainly, I don't understand how/why not update system would be to download and install an incorrect driver.  VERY FRUSTRANT and TEDIOUS!

• Use WAN connected airport Time Capsule as a wireless access point

  I had to replace a failed 4 Gen Time Capsule. I tried to install a new Gen 5 airport TimeCapsule via WAN and set up the airport to act as a wireless access point. It is installed in an area of my house with wireless coverage. In the network of AirPort Utility Mode section, I chose "extend a wireless network. The TC is restarted, I get an error message cannot find the intended wireless network.

  What I lack?

  "Extend a wireless network" is a parameter that is only used if the time Capsule need to connect to another router from Apple with the help of a Wi-Fi connection.

  You use Ethernet to connect, you must use the parameter to "create a wireless network. Use the same wireless network name and the same password as your "primary" router

• The WRT600N can connect to a wireless access point?

  I installed Windows 7 on my desktop and I was not able to install all types of Linksys wireless adapters.  I decided that linking an my WRT600N wireless access point in the other room and hardwireing the office to the access point, would be a good idea.  I'm probably going to connect it to a Net WTG624 Gear, which is capable of acting as an access point and you connect to another router.  The question is, can the WRT600N you connect to and use the internet and the local access and, ultimately, on the Office of cable?  I feel that it is one of the most stupid questions, I ask myself here again, but I'm not sure.

  EDIT: I'm sure it's called Wireless Bridge.

  Thank you

  Zach

  Hello Zach,

  The WRT600N can connect at the point of access, and vice-versa. I have a WRT600N home and have the same model of NetGear as access point (what are the chances?) and it works fine, although I do miss the 5 GHz as the Access Point is only 2.4 Ghz 802.11 g Standard.

  I hope this helps!

• There is no communication between devices that are connected to the Linksys WAP4410N Wireless access point?

  Hi all

  I have deployed the new Linksys WAP4410N Wireless Access Point and it works fine. Laptop which is connected to the AP may be able to access the internet. It can communicate with AP and also the gateway IP (IP Router) but it is wireless devices are not able to communicate with each other. In the case of peripheral LAN can communicate with wireless devices. Cannot able to share files between wireless devices.

  Please help me solve this problem. Wat could be the problem here. Stage of Wat I have to take to eliminate this problem.

  Advance thanks.

  Thank you and best regards,

  Chandhuru.M

  Hi, my name is Eric Moyers. I am a network Support Engineer in the Cisco Small Business Support Center. Please use the Forums to Post community of Cisco.

  The title of security without thread/how do you have isolation set up wireless?

  Insulation wireless (SSID) on the inside must be disabled to allow the computers associated with the same SSID to see and transfer files between them wireless

  Thank you

  Eric Moyers. : | :. : | :.

  Cisco Small Business U.S. STAC Advanced Support Engineer

  CCNA, CCNA-wireless

  866-606-1866.

  Mon - Fri 09:00 - 18:00 (UTC - 05:00)

  * Please rate the Post so other will know when an answer has been found.

• Unable to connect to the internet using D - Link DWA - 131 Wireless N Nano USB Adapter

  I have a D - Link DWA - 131 Wireless N Nano USB Adapter and I can not run on win 7 ult x 86. in Device Manager, the device is functioning. Driver is Realtek Semiconductor Corp. 1086.33.917.2010. in network connections wireless 3, problems of Diagnostics network found influential connection (there could be a problem with the driver for the wireless connection 3 network adapter) is there a way to get this working?

  Original title: D-Link DWA - 131 Wireless N Nano USB Adapter and win 7 ult x 86

  Hello

  1. you receive an error message/code?
  2. were you able to use this device sooner? If Yes, did you the latest changes on the computer before this problem?
  3. what happens when you plug the device into USB port?

  See the help articles and check if it helps.

  Setting up a wireless network
  http://Windows.Microsoft.com/is-is/Windows7/setting-up-a-wireless-network

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Check out the link:
  How to make my wireless adapter will work or install correctly in my Windows 7 / Vista / XP computer?

  http://www.Dlink.com/us/en/home-solutions/support/FAQs/adapters/Bluetooth-adapters/how-do-i-make-my-network-wireless-adapter-work-or-install-correctly-in-my-Windows-7-Vista-XP-compute

   
  If the problem persists I suggest you to contact Dlink

  Contact the Support - http://www.dlink.com/us/en/home-solutions/support/contact-support

  Let us know if it helps.

• Set up the wireless access point, but the wireless devices are unable to get ip address

  Hi, I wanted to put my D7000 as router AP. My main router is Sagemcom F@st 3864 by Optus ISP (Australia).

  First of all, I put the D7000 in Bridge mode I did these steps:

  1. replace the IP LAN 192.168.0.100

  2 disable DHCP

  3. connect the LAN port to the main router Lan port

  Internet connection wired and wireless on the same device but other wireless devices has failed

  To remedy this, I made another choice, allowing point-to-point wireless access in the advanced settings of the D7000. I followed the instructions from this link

  http://KB.NETGEAR.com/app/answers/detail/A_ID/24104/~/how-do-i-change-my-Nighthawk-router-to-AP-mode...

  I put dynamiccaly = wireless internet cable success but peripheral does not have an ip address

  No idea how to fix wireless? I'm not very experienced

  Thank you!

  I just fixed it just now. For AP mode, connect the LAN port of the main router to the WAN port on the D7000 (not LAN to LAN). I wish I thought to it much sooner.

• Changing the E3200 as wireless access point

  Hi, I recently bought an E8350 router and have a spare E3200. How can I change E3200 as an another access point wireless to work with my new E8350? Thank you very much.

  You want to connect your E3200 to your new E8350? You can mount the two cascading, but I suggest you do the E8350 as your main router and connect the E3200 so that it will act as an access point. You can watch this video for you guide: http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=b946afd839aa48938783df77f009e155_Cascading_your_Li...

• Use E2000 as ONLY - wireless access point not as a router

  I would use my E2000 router as an only Wi - Fi access point. The unit will be connected to a unit of combo modem/router Verizon FiOS Actiontek I want to leave only the first and only router on my network. Can the E2000 cause its router functions disabled without DD - WRT or other third party firmware?

  Thank you!

  Yes, but you need to connect a cable between the router to the AP, here's how

  Editing cascading (connecting) a Linksys router to another router

• Unable to connect to the internet (using a wired connection or wireless) after a power failure, error "the cable network is disconnected"

  After a power outage, I can not connect wireless (cannot connect even with the wired ethernet cable); get message "network cable is unplugged", which is not.  The cable modem work properly in wireless mode with two other computers.  System to an earlier date of reload and change the cable has not solved the problem.  Running Windows XP.  Any suggestions?

  Hello

  I suggest to follow the steps provided and check if it helps.

  How to troubleshoot the following message appears in Windows XP: "a network cable is unplugged": http://support.microsoft.com/kb/910389

  Hope this information is useful.

• Unable to connect to the internet using Google or Windows Live Mail access

  I have an Acer laptop with Windows 7.  Every time I have to connect to the Internet via Google, or attempt to access my emails on Windows live mail, it takes forever to connect to the time and the high bar always notes that Windows does not.  Please notify.  This happens only in the last year, no problems prior to this.

  What type of connection Internet?

  What Antivirus utility do you use?

  This happens in other web browsers?

  If you are on a wireless connection, try switching to a wired connection and try the download.

  Click Start, type: cmd

  Right-click on cmd, and then click Run as administrator

  At the command prompt, type the following:

  ipconfig/release

  then

  ipconfig/renew

  then

  ipconfig/flushdns

  leave the command prompt

  Click Start, type: folder

  Press enter

  Delete the contents of the temp folder

  Restart the computer and try to download again.

  If the problem persists, try resetting your router if you are connected to one.

  Turn off the router, unplug it, wait 10 minutes

  Plug it in again, power up once again

  Reconnect the Ethernet cable

  Try to access these web services again.