Is it possible to directly connect dish Qosmio G20?
HY everybody,
I have a Qosmio G20-PQG21. The receiver is 60 metres from the position of the laptop. In this case, the channel is not editable. The problem that this person wants to change channels. The problem is quite simple... can I connect the coaxial cable from the dish directly to tv tunner and setup guide? or do you have another solution for my situation?
Thanks in advance
Hello
In my opinion it of not possible connect the cable satellite directly the Qosmio.
You are also unable to connect the TV directly with the satellite dish. It of the same case on the laptop. You need a receiver sat between the laptop and the flat sat.
There are two possibilities:
1.), you buy a longer cable from the satellite dish to the receiver and place the receiver closer to the laptop.
2.), you place the laptop more near the sat receiver ;)
Tags: Toshiba
Similar Questions
-
Connection to (Qosmio G20) Surround sound
I'm trying to connect my Qosmio G20 to my sysytem via an amp external surround sound.
As far as I know I have everything connected correctly, but I'm only obtaining from my front left speakers and rear no where elsewhere.
I checked the speakers and all the settings I can think on the laptop, is there something that I don't have to send the signal to all the speakers?
Any help is greatly appreciated.
Thank you very much
Hello
Check it please this http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=3665&messageID=12229#12229 topic. I believe that display Quad will be useful for you.
Good luck!
-
How to connect the Qosmio G20 to screen plasma HD
Hello... I'm so confused! ... Please can someone advise me... Read all the posts on this... What is the best way to connect G20 - 139 running Vista Home to a Plasma HD? ........ Can I buy a D-video to HDMI Cable (searched on the net but not sure of what I seek in a cable... (LOL)... any help please... I am not an expert!
Hello
If you have time please check this topic http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=11821
For me, it is very interesting and you can find a very interesting discussion on the Qosmio G20 to connect to an HD-ready LCD TV.
Good luck!
-
How to connect the Qosmio G20 156 to DTT2200 sound creative
Can someone recommend the best way to connect my G20-156 sound creativity works 5.1 desktop theater DTT2200. This was connected to a PC so I think a card external sound would be via a USB port, but is this the best way and that model?
Hello
I put t know what cables and what made the 5.1 support desktop theater DTT2200 but the Qosmio supports headphones with S/PDIF out.
I use the headphone jack on my satellite to connect the unit to the stereo.
I use a cable with a connector on one end and RCA connectors (red and white) 2 on the other end of the cable.
The two connectors, I connected to HiFi and taking helmet.I think you can also try to use the same way to connect external speakers for the Qosmio.
-
How to connect a Qosmio G20 to a TV?
Hi, I posted here a long time ago and I have not yet found a solution to this problem.
I want to connect my laptop to my TV. I'm always in another room, so I'll be either hanging up to 21 "Toshiba, or 32" Sony or 51 "Toshiba - I don't know if hang to different brands of TV will create a problem. I tried to plug the laptop computer with an S-video cable and a DVI cable (who both wired SCART at one end).
I can't get the thing to work with a TV! Here is exactly what I do when I try:
* I click on start then click on Control Panel
* I click on 'appearance and themes '.
* I click on "display".
* I click on the tab "settings".
* I click on 'Advanced '.
* I click on the tab "GeForce Go 6600.
* I select settings to make me a clone view on digital flat screen and a TV.
* I click "Device settings" to make sure that all the settings of the TV are correct.
* I press "Apply" and nothing happens!Can someone help me? I've had this laptop for centuries and I still have this feature not to work! Any help will be really appreciated! I look forward to THE answers.
Thank you very much!
You forgot to put a thing.
Have you chosen the right channel of the TV, and you enabled the S-video on the TV?
Check it outPS: You can switch to the external display also with the key FN + F5 combination
-
Qosmio G20 - HDMI to LCD TV connection
Hi all
I would like to connect my Qosmio G20-139 directly to my LCD TV using the HDMI connection. The G20 has a d-connector on the back that I thought was HDMI, but impossible to find a cable to do it with. Anyone know if this is possible?
Concerning
Roland
Hello Roland
As much as I know Qosmio G20 certainly has no HDMI port but port component and it looks like the HDMI port. I found the very interesting thread on this forum and you can find a very interesting discussion on the Qosmio G20 and LCD TV connection.
Check it out under the http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=11821
Good bye
-
Qosmio G20-139: What cable I need to connect a 5.1 system speakers?
Hi all
Does anyone know which cable or connector, I need to connect my Qosmio g20-139 to a 5.1 system speakers?
I searched the forum and it seems that someone has used a "optical cable Toslink" - check link below:
http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=3665
Anyone successful with this? Can someone please give me a link to a place I can buy something that works? (I put 'Toslink optical cable' in google and it gives like 1 million different things!)
Thanks for your help.
Chris
Hello Chris
I found a useful site on the required cables.
Check out this link.
http://www.mycableshop.com/2nd_Cat/Toslink.htmYou wondering where you can buy these cables. I put t know you came but I m sure that every good PC or reseller of audio accessories can sell you these cables.
-
Qosmio G20 - 127 connection with plasma TV
What is the best way to connect the Qosmio G20-127 with plasma Panasonic TV? Plasma TV has HDMI port. Should what cable I be able to connect to the HDMI port?
Hello
The Qosmio G20-127 supports a component port (D-video output port)
You can connect you laptop to TV with a D-video cable.
You can google a bit and you will find a lot of offers. -
Can I use the Qosmio G20 as a mediacentre?
Hello
Is it possible to really use the Qosmio as a mediacentre?
I want to have the Qosmio in one piece and then plug the tom my TV and the audio Center in another room.
For the photo I think than the DVI on can be used, but for the sound, which can be used?Everything must be used by the remote control.
Allt sounds possible (on papar) but I failed to do as a speider web mediacentre in my house?
Each of you?
/ Lars
Hello
If you want to connect the Qosmio g20 on the HIFI audio system I advise to use audio S/PDIF output line.
The plug is the same as the headphone jack.
I think you should be able to use it with the MCE or Qosmio player.
I think that the remote control only works with MCE but I m not 100% sure. -
Qosmio G20 to Mini HiFI Stereo Speaker System AV cable
Hello
When I connect my Qosmio G20 to my stereo using the AV cable (with jack white, yellow and red) and my Qosmio includes a cable that joins this cable 3 to the line of the laptop for the helmet.
The problem is, it only sends the sound to a speaker if I swap the cable then any other speaker works and the previous No.
I've tried installing speakers / two speakers on the options here and nobody done work.
I tried another set of audio/video cable and it is the same question.
This configuration works correctly if I connect it to the TV, but not on my stereo system.
Do I need a different cable?See you soon
Hello
Are you sure you have connected the straight plugs at the HiFI?
You receive a stereo sound will have to connect only two sheets: RED and WHITE.I ve also connected my phone to the stereo via a cable 1-2: a plug for headphones and 2 plugs (left, right) to the stereo.
Everything works beautifully.Oh I remember that my HiFi supports a controller at the rear to assign the sound to the left or right speaker.
I put it at intermediate level for both speakers.
Maybe it's the same on your HiFI -
1st generation Apple TV is dead. Orange light but no screen and no resetting of distance. I tried direct connection to Mac and iTunes open and he's not here. Is it possible to restore to the factory without screen or remote workin
I guess you tried maintained low men together for about 6 seconds - silver 1 ATV that will restart to the diagnostic partition but who would rely on the hard disk is functional and if it was ok that wouldn't work with the logic board failure.
I guess you have not fed and attempted to restart.
In case your AppleTV think it is paired with another remote try Menu and left arrow for 6 seconds - the light now intervenes when you press the buttons on the remote?
Also, it could be in the video mode bad - try Menu and upward arrow together for 6 CES switch video modes, but implies that he actually started OK.
-
Hello
I connected two computers, one running on windows xp sp2 and others running on windows xp sp3 via com using RS232 port via link Modem DFM-562E ++.
I am able to dial numbers from a PC successfully.
But when I do a direct link between them (one as a host, the other guest) through the com port, I get error 777.
Is this because the two PC's using different service packs?
Help, please.
Thank you & best regards
RaviIt is not the service pack - although you should have installed sp3 now.
Your message is not clear: have you been able to connect successfully computers using your modem D-Link? How did you do that? Will there be a modem in the second computer?
What cable are you using to establish a direct connection between the com ports on both computers? If you have purchased this cable online, please provide a link to the site where you bought it.
Please describe the physical connection between the two computers. For example, this is how you connect to the Internet by dial-up services:
computer 1-{(9 broches) RS-232 serial port}-{RS-232 cable supplied with the modem}-{modem}-{phone cord (RJ-11 modular plugs at each end)}-{telephone wall jack}
-
Qosmio G20: Possible boot from a USB device?
Dear all,
I am writing for you good people was whether it is possible to start a Qosmio G20 via a connected USB device, an external hard drive.
I wonder if it is taken in charge (or tolerable) within the limits of the current Qosmio G20 BIOS and/or if any could attempt on my part to make taken in charge (i.e. are there buttons I can push levers, I can pull or numbers I can play to get there).
The reason why I have is that my laptop has a multitude of technical difficulties that point to the hardware failure, among them a vertical line on my screen and a problem with my optical drive, making it impossible for me to write a CD or DVD.
In the unlikely event that the good folks at Toshiba support are forced to replace the hard drive (or the system) it would be nice to have a way to restore the system to its current configuration (in this sense, I'm looking for a way to create my own bootable recovery disc produced) however the lack of functionality in the Department of optical drive ties my hands a little (I can't create a recovery of) product custom CD/DVD but I might create a product on my external HARD drive recovery partition).
Thus, it would be useful to be able to boot from a USB, not essential of course as any disk image could be comfortably written to disk through my soon-to-be renovated system (of course it would be quicker to start just by the USB bus and avoid all this nonsense).
Sincere greetings,
Lee Hyde.Hello
I am sorry to say that you will not be able to boot from the external USB HDD. The BIOS does not support this feature.
According to different threads here in the support of forum Toshiba Qosmio G20 BIOS supports these devices to start:
Floppy USB drive, 1st/2nd HDD, ODD, network (LAN)As you can see it s possible to floppy USB FDD but not the USB external HDD
-
Direct Connect with GPS or other active data
I'm testing the possibility of using the functionality of direct connection to and from a phone while accessing other critical mission for my work tasks. We require the use of a tracking application that captures and sends GPS coordinates to a server via a data connection and also to connect to work through tasks via a web browser application. Direct connection cannot be launched on the phone while the user has any running application that uses data, it seems. It will work when the tracking application is closed and that the browser is slow and not loading pages, but doesn't if the browser will load a new page, the GPS application is running or even just Google maps. Can you get it someone please let me know if the i1 should be able to use Direct Connect when using other services that use data? I have been informed by Sprint that it is possible (two other applications can run on the data at the same time). The phone lacks a voice, only data plan.
No, you can't. If something is using data on an iDEN connection, that's all. That's all it will do. It's just the nature of identity. If you want a phone that will have voice and data communications at the same time, you need to use CDMA or GSM.
-
EqualLogic PS6100X: direct connections (double) iscsi to 3 vmware ESX host
Hello
Due to the reduction of costs, we integrate
1 x ps6100x Dell Equallogic (2 controllers to each 4 ports)
3 x dell poweredge r720 (each have 2 ports dedicated for trafficking SAN storage)
vSphere 5.5 (shared storage on the San)
Without the use of SAN switches. Each host has dual direct connection (1 to each SAN controller) with the initiator iscsi software.
We did before with Dell MD3200i, who has also 2 controllers and 8 ports, so we expect no problems.
But now that I have read on the Equallogic, I'm starting to become uncertain if this Setup will work?
I know that this is not recommended, but at this point, my only concern is that it will work (even with less performance).
Can you please give me some advice on this?
Best regards
Joris
P.S. If this is probably NOT possible, what would be the best/low average cost to make this possible?
I've seen this failure at work, as in the connections dropped, BSOD was virtual machines with a single host with no switch. iSCSI traffic tends to be very burst, which is having when the right switch pays you back.
Re: 3750 X are those good switches, there is some adjustment settings that need to be addressed. Also to solve a flowcontrol problem download the most current IOS firmware.
For such a small group / number of servers, the stacked 2960 would be OK. Perhaps to problems later if you need to scale this environment. lack of 2960 allocate buffer, then you want to start without Jumbo frames, all enter into stable and of good practices. So maybe later try enabling it. 3750 X works very well with Jumbo and Flowcontrol active BTW.
These choices are better than no switch miles. 3750 x were pretty expensive last time I looked. Unless you have a little already. If you share them with the rest of the traffic that is not optimal, but at least put all ISCSI traffic on its own VIRTUAL local network.
4948 are the right choice. Some high-end HP switches. Step away from the elders, like 2810 or 2824/48. They seem to be there for cheap $$ but are designed for GbE Office not GbE iSCSI.
Kind regards
Maybe you are looking for
-
Installed FF9.0.1. I type a word in the google search bar and results. When I select 'shopping' from the left navigation, it flashes the results and then refreshes instantly to a white page with this in mind: (function() {}) ();(function(){})(); The
-
I checked with the developer of the extension sites, but they do not yet report if the extension has been tested with Firefox 6.0. 3.6-4.0 switch left me with a gap in functionality of my extensions, although the switch of 4.0 to 5.0 went smoothly. I
-
Satellite L10 - no DVD/MPEG/DivX playback
I can't play a DVD or file MPEG/DivX on the Satellite L10 of my aunt. Further when you start some games, I get error messages like that Direct3D has failed. When you try to playback MPEG/DivX with WinAmp only sound can be heard but not video. Trying
-
Qosmio x 70-A-12-question on the use of the external monitor
Hello am about to buy an external monitor and I was wondering what would work with my laptop.I want to it works like an additional surface (not a copy of my current screen) with both screens at the same time working. My laptop seems to have a VGA por
-
I have a Photosmart C4680 HP which works fine except it will not scan anything. I read the previous posts here but could not connect to link who recommended the service representative. Please help me! From the looks of this thread, I'm not the only o