is it possible to get drivers on the hp sites, I need the driver to get online to connect to the local network.

Similar Questions

• Satellite L500 - no possibility to connect to the local network

  Hello

  I'm new to these forums so please accept my apologies if I don't use the terminology correct tech.

  I have a Toshiba L500 laptop satellite. It of ok, but had to make the hard drive replaced recently (under warranty) as she died. I had been using a wireless network before I had to have the drive replaced and now trying to connect to a local network using a cable, but there is no device?

  Now, I don't know when this became a question - before or after replacing the hard drive. Not only has he failed to drive hard, but has so the speakers, so I wonder if the LAN device is just another thing that has failed.

  I understand that there are two components to the unit - the hardware and software. I learned that the material may have failed.

  Does anyone know how to get back the unit so that I can plug my computer on a local network and internet access? No, the device isn't in the network adapters. I don't know how to get it back.

  > I have the replaced disk and now I'm trying to connect to a local network using a cable, but there is no device?
  Have you tried reinstalling the driver LAN?

  Remember that the network driver is installed correctly you should check this in the device-> network cards Manager.
  In this category the LAN card and wireless network card required!

  If you're going to see some yellow exclamation points, so this means that a driver is missing or is not working properly and this means that you must remove/uninstall the driver, and after new restarts, the driver needs to be installed once more

  Please check this!

• Client remote access VPN gets connected without access to the local network

  : Saved

  :

  ASA 1.0000 Version 2

  !

  hostname COL-ASA-01

  domain dr.test.net

  turn on i/RAo1iZPOnp/BK7 encrypted password

  i/RAo1iZPOnp/BK7 encrypted passwd

  names of

  !

  interface GigabitEthernet0/0

  nameif outside

  security-level 0

  IP 172.32.0.11 255.255.255.0

  !

  interface GigabitEthernet0/1

  nameif inside

  security-level 100

  IP 192.9.200.126 255.255.255.0

  !

  interface GigabitEthernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/4

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/5

  nameif failover

  security-level 0

  192.168.168.1 IP address 255.255.255.0 watch 192.168.168.2

  !

  interface Management0/0

  nameif management

  security-level 0

  192.168.2.11 IP address 255.255.255.0

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain dr.test.net

  network of the RAVPN object

  192.168.0.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.168.200.0_24 object

  192.168.200.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.9.200.0_24 object

  192.9.200.0 subnet 255.255.255.0

  the inside_network object-group network

  object-network 192.9.200.0 255.255.255.0

  external network object-group

  host of the object-Network 172.32.0.25

  Standard access list RAVPN_splitTunnelAcl allow 192.9.200.0 255.255.255.0

  access-list extended test123 permit ip host 192.168.200.1 192.9.200.190

  access-list extended test123 permit ip host 192.9.200.190 192.168.200.1

  access-list extended test123 allowed ip object NETWORK_OBJ_192.168.200.0_24 192.9.200.0 255.255.255.0

  192.9.200.0 IP Access-list extended test123 255.255.255.0 allow object NETWORK_OBJ_192.9.200.0_24

  pager lines 24

  management of MTU 1500

  Outside 1500 MTU

  Within 1500 MTU

  failover of MTU 1500

  local pool RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 IP mask

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 66114.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) source Dynamics one interface

  NAT (it is, inside) static static source NETWORK_OBJ_192.9.200.0_24 destination NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.9.200.0_24

  Route outside 0.0.0.0 0.0.0.0 172.32.0.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  Enable http server

  http 0.0.0.0 0.0.0.0 outdoors

  http 0.0.0.0 0.0.0.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  Terminal registration

  name of the object CN = KWI-COL-ASA - 01.dr.test .net, C = US, O = KWI

  Configure CRL

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  authentication crack

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 20

  authentication rsa - sig

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 40

  authentication crack

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 50

  authentication rsa - sig

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  authentication crack

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 80

  authentication rsa - sig

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 100

  authentication crack

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 110

  authentication rsa - sig

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 120

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 130

  authentication crack

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 140

  authentication rsa - sig

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 150

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet 192.9.200.0 255.255.255.0 inside

  Telnet timeout 30

  SSH 0.0.0.0 0.0.0.0 management

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH 66.35.45.128 255.255.255.192 outside

  SSH 0.0.0.0 0.0.0.0 inside

  SSH timeout 30

  SSH version 2

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow outside

  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

  AnyConnect enable

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  internal RAVPN group policy

  RAVPN group policy attributes

  value of server WINS 192.9.200.164

  value of 66.35.46.84 DNS server 66.35.47.12

  VPN-filter value test123

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value test123

  Dr.kligerweiss.NET value by default-field

  username test encrypted password xxxxxxx

  username admin password encrypted aaaaaaaaaaaa privilege 15

  vpntest Delahaye of encrypted password username

  type tunnel-group RAVPN remote access

  attributes global-tunnel-group RAVPN

  address RAVPN pool

  Group Policy - by default-RAVPN

  IPSec-attributes tunnel-group RAVPN

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory 2

  Subscribe to alert-group configuration periodic monthly 2

  daily periodic subscribe to alert-group telemetry

  aes encryption password

  Cryptochecksum:b001e526a239af2c73fa56f3ca7667ea

  : end

  COL-ASA-01 #.

  Here is a shot made inside interface which can help as well, I've tried pointing the front door inside the interface on the target device, but I think it was a switch without ip route available on this subject I think which is always send package back to Cisco within the interface

  Test of Cape COLLAR-ASA-01 # sho | in 192.168.200

  25: 23:45:55.570618 192.168.200.1 > 192.9.200.190: icmp: echo request

  29: 23:45:56.582794 192.168.200.1.137 > 192.9.200.164.137: udp 68

  38: 23:45:58.081050 192.168.200.1.137 > 192.9.200.164.137: udp 68

  56: 23:45:59.583176 192.168.200.1.137 > 192.9.200.164.137: udp 68

  69: 23:46:00.573517 192.168.200.1 > 192.9.200.190: icmp: echo request

  98: 23:46:05.578110 192.168.200.1 > 192.9.200.190: icmp: echo request

  99: 23:46:05.590057 192.168.200.1.137 > 192.9.200.164.137: udp 68

  108: 23:46:07.092310 192.168.200.1.137 > 192.9.200.164.137: udp 68

  115: 23:46:08.592468 192.168.200.1.137 > 192.9.200.164.137: udp 68

  116: 23:46:10.580795 192.168.200.1 > 192.9.200.190: icmp: echo request

  COL-ASA-01 #.

  Any help or pointers greatly appreciated, I have do this config after a long interval on Cisco of the last time I was working it was all PIX so just need to expert eyes to let me know if I'm missing something.

  And yes I don't have a domestic network host to test against, all I have is a switch that cannot route and bridge default ip helps too...

  Hello

  The first thing you should do to avoid problems is to change the pool VPN to something else than the current LAN they are not really directly connected in the same network segment.

  You can try the following changes

  attributes global-tunnel-group RAVPN

  No address RAVPN pool

  no mask RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 ip local pool

  local pool RAVPN 192.168.201.1 - 192.168.201.254 255.255.255.0 IP mask

  attributes global-tunnel-group RAVPN

  address RAVPN pool

  no nat (it is, inside) static source NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 static destination NETWORK_OBJ_192.9.200.0_24 NETWORK_OBJ_192.9.200.0_24

  In the above you first delete the VPN "tunnel-group" Pool and then delete and re-create the VPN pool with another network and then insert the same "tunnel-group". NEX will remove the current configuration of the NAT.

  the object of the LAN network

  192.168.200.0 subnet 255.255.255.0

  network of the VPN-POOL object

  192.168.201.0 subnet 255.255.255.0

  NAT (inside, outside) 1 static source LAN LAN to static destination VPN-VPN-POOL

  NAT configurations above adds the correct NAT0 configuration for the VPN Pool has changed. It also inserts the NAT rule to the Summit before the dynamic PAT rule you currently have. He is also one of the problems with the configurations that it replaces your current NAT configurations.

  You have your dynamic PAT rule at the top of your NAT rules currently that is not a good idea. If you want to change to something else will not replace other NAT configurations in the future, you can make the following change.

  No source (indoor, outdoor) nat Dynamics one interface

  NAT source auto after (indoor, outdoor) dynamic one interface

  NOTICE! PAT dynamic configuration change above temporarily interrupt all connections for users on the local network as you reconfigure the dynamic State PAT. So if you make this change, make sure you that its ok to still cause little reduced in the current internal users connections

  Hope this helps

  Let me know if it works for you

  -Jouni

• Re: Satellite Pro A40 - connection to the local network

  Hello

  My names Andy and not bieng a total beginner computer, I tried to install all the drivers for my laptop model a SPA40 old fathers PSA45E-001VM-EN. (European model I think) everything looks ok, except that I can't get the ETHERNET driver.

  When I go into the Device Manager there is NO controller network displayed in the list and there is a yellow exclamation mark against two controllers ethernet ib the OTHER DEVICES tab looking here, I downloaded the atheros wlan xp file - 7704062.zip, broadcom wlan xp - installed 5604835.ziplan20070912134727.zip and nothing changes, we used to be able to go on the net and with the wifi card in the pci slot wireless go so I know its capable I think it's just the order of drivers and the drivers themselves,

  Then someone can point me in the right direction before as I have send myself crazy with this...

  You can

  regards and thanks in advance

  Andy

  Hey,.

  The drivers that you downloaded are WLAN Card and has nothing to do with the connection to the local network (Ethernet) normal

  I think you should check the Web from Toshiba site to download the latest LAN driver. You can find the drivers for Satellite Pro A40 in * archives *.
  ttp://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp h

• No connection to the local network, cannot connect - Satellite M35-S163

  I think I've tried about 10 different drivers, but I can't ALWAYS connect to the local network.

  He will not get an IP address.

  Other computers have no problem and are connected through the router, but it just won't connect.

  DHCP in router, IP config says the get IP address... No firewall issue... Any new installation of XP SP2

  Any ideas?

  OH, and regarding this... discovered Ethernet controller driver is on one of the Wireless drivers... z

  Hello

  I m bit confused.
  The LAN card is recognized correctly in the Device Manager?
  Check under network adapters and if there is NO yellow exclamation point.

  If the network card is recognized correctly, then you should check the LAN parameters-> * Protocol of TCP/IP.

  IP address, getway must be set to assign automatically.

  Check it!

• cannot connect to the local network using windows 7

  Recently bought a HP Pavilion laptop (AMD Athlon II P320 Dual - Core) ((G62 - 208CA)). Having a problem connecting to the local network. I have flashing lights on the lan (orange and white) connector.

  Using the ipconfig command, I get an IP address, subnet mask and gateway by default however messages below will appear:

  Tunnel adapter isatap. <578608BD-22EF-4A01-90ED-D709CB81D027>:

  State media: media disconnected

  The connection-specific DNS suffix. :

  Tunnel connection to the Local network adapter * 9:

  State media: media disconnected

  The connection-specific DNS suffix. :

  Tunnel adapter isatap. :

  State media: media disconnected

  The connection-specific DNS suffix. :

  TEREDO TUNNELING Pseudo-Interface tunnel adapter:

  State media: media disconnected

  The connection-specific DNS suffix. :

  Tunnel adapter isatap. our field: *

  State media: media disconnected

  The connection-specific DNS suffix. :

  I tried to turn off the firewall and connect without success

  My network card is a Realtek PCIe FE Family Controller and confirmed that the drivers are up to date

  Any help would be appreciated

  Thank you

  Well Yes! So it was an older version of the bonjour service... thank you Adobe.

  You can find the latest version here:

  http://support.Apple.com/kb/DL999

• Cannot turn off the Local network

  Message icon and get XP Pro SP3 right click LAN "it is not possible to disable the connection at this time. The connection may be using one or more protocols that do not support plug-and-play, or it may have been initiated by another user or the system account.

  I am the only user and administrator.

  When I di ipconfig/all, I get this:

  Microsoft Windows XP [Version 5.1.2600]
  Copyright (C) 1985-2001 Microsoft Corp.

  C:\Documents and Settings\Administrateur > ipconfig/all

  Windows IP configuration

  Name of the host...: laptop
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.
  ... DNS suffix search list: domain_not_set.invalid
  domain_not_set. Invalid

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : domain_not_set.invalid
  ... Description: Intel(r) PRO/100 VE Network Connection
  Physical address.... : 00-0F-1F-A1-0C-53
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  ... The IP address: 192.168.1.67
  ... Subnet mask: 255.255.255.0.
  ... Default gateway. : 192.168.1.1.
  DHCP server...: 192.168.1.1.
  DNS servers...: 192.168.1.1.
  184.16.4.22
  Lease obtained...: Tuesday, October 12, 2010 10:18
  End of the lease...: Wednesday, October 13, 2010 10:18

  Ethernet wireless network connection card:

  The connection-specific DNS suffix. : domain_not_set.invalid
  ... Description: Dell Wireless 1350 WLAN Mini-PCI Card
  Physical address.... : 00-90-96-A7-2C-08
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  ... The IP address: 192.168.1.68
  ... Subnet mask: 255.255.255.0.
  ... Default gateway. : 192.168.1.1.
  DHCP server...: 192.168.1.1.
  DNS servers...: 192.168.1.1.
  184.16.4.22
  Lease obtained...: Tuesday, October 12, 2010 10:18:29
  End of the lease...: Wednesday, October 13, 2010 10:18:29

  Hi cciaffone,

  If you can't turn off your connection to the local network by going to the network connections

  Please try to disable it via Device Manager

  go to RUN and type the following command in the RUN: DEVMGMT. MSC

  under network card try turning off your ethernet card.

  hope that helps

• No Internet access, the 'Connect to the Local network' and 'Wireless network connection' are "Local only".

  I'm portable computer maintenance of the customer, a Toshiba Satellite L305-S5885, under Vista Home Premium x 86 SP2, with infections by malicious software and internet connection problems. I have managed to get rid of all of its 251 infections and I am now addressing the connectivity problem. I'm unable to achieve on its ethernet or a wireless connection to Internet. The two network status of connections 'Unidentified network', and also ' access: Local only ' all other machines hooked up to my router via CAT5e and some via 802.11 g/n, have excellent speeds with internet connectivity, so I know that the problem is limited to his machine. I tried the following:

  Deactivation and reactivation of these two connections: FAIL.

  "Diagnose and repair" on the two connections: FAIL.

  Under dynamic I.P. type to static/static to the dynamic: FAIL.

  Uninstalled all network via Device Manager devices, then restart: FAIL.

  Manually uninstalled all the drivers and utility and installed the latest versions: FAIL

  The command ipconfig/all text follows:

  ----------------------------------------------
  Microsoft Windows [Version 6.0.6002]
  Copyright (c) 2006 Microsoft Corporation. All rights reserved.

  C:\Users\Brooklyn's>ipconfig/all

  Windows IP configuration

  Name of the host...: Brooklyns-PC
  Primary Dns suffix...:
  Node... type: broadcast
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Intel (r) Wireless WiFi Link 4965AGN
  Physical address.... : 00-21-5C-31-87-95
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Autoconfiguration IPv4 address. . : 169.254.174.235 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
  Description...: Realtek RTL8102E Family PCI - E Fast Ethern
  and NIC (NDIS 6.0)
  Physical address.... : 00-1E-33-4E-2E-F7
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Autoconfiguration IPv4 address. . : 169.254.74.29 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  NetBIOS over TCP/IP...: enabled

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {C41651CC-0B3D-411D-8187-745214 C 69}
  B4B}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {816357D 3-D 8-494C-AA09-F622AE861 44}
  0FA}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 14:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  C:\Users\Brooklyn's >
  --------------------------------------------------

  Guys, I'm really hitting my head against the wall on this one, and I would be VERY happy for any help through this. Thank you!

  I thought about it, there was a corrupted installation of Norton 360, the origin of the problem. I've used the Norton removal tool and voila! Internet! Thank you.

• I am refurbishing a Pavillion m7560n and I can't find a driver for the local network. Can you help me? CC = en

  I am refurbishing a Pavillion m7560n and I can't find a driver for the local network. Can you help me?

  Here is the link to the LAN of your system drivers:

  http://ftp.HP.com/pub/softlib/Software7/COL15134/ob-40490-1/sp26744.exe

• Connection to the local network not appearing is not in network connections

  A month or so I reinstalled Windows XP SP2 (have since updated to SP3), and ever since then the LAN connection icon does not appear in the network connections window, and even when I plug the ethernet cable it does not automatically turn on the connection to the local network. My wireless connection works perfectly well. I went to the HP website to download all the drivers and also visited if the Device Manager on my computer to make sure that all drivers are in place. Even with all the drivers, it still does not connect to the local network. Help, please!

  Hi rawkous,
   
  Follow the steps listed in this article to resolve the problem:
  How to troubleshoot missing network connections icons in Windows Server 2003 and Windows XP

• Impossible to connect to the wireless network when the wireless Internet is filled to connect to the Local network

  I tried to fill the connection between my laptop Wi - Fi and an ethernet cable LAN via the connection to the Local network for my xbox 360. However, when the connections passed the wireless connection would show that it is disconnected and would not reconnect. When I tried to repeat the process sometimes the same thing happens sometimes it says that it is still connected.

  However, be that as it may, both times I could not load any page of the website from my laptop and xbox connect any.
  How can I create a network bridge and get the wireless internet to connect please?

  Any help to fix this would be appreciated,
  P

  This Microsoft Knowledge Base article might help: bridge may not work with a Non-Promiscuous Mode network card .

  If not, I recommend to delete the network bridge and enable sharing of Internet connection on the wireless network connection. Boulder computer Maven
  Most Microsoft Valuable Professional

• lost internet, tcp/ip is not binding to connect to the local network.

  cannot access internet on network adpt since Saturday, January 22, 10.  said Network Diagnostics does not bind ip to connect to the LAN adpt.  When I go to L A Conn ipv4and6 properties are both checked.  I uninstalled and reinstalled the ptba and ip lan protocols.  ipconfig/all shows no IP information.  I have reset the battery.  network of diag stills said make sure that tcp/ip4 and ip6/tcp are selected in the config to connect to the local network [but they].  TIA

  try to uninstall and reinstall the network drivers and check if that helps

  For more information, you can refer to:
  http://www.madboa.com/geek/SOHO-bind/
  http://TechNet.Microsoft.com/en-us/library/cc977313.aspx

• Connected to the local network, but can not use internet

  I recently had problems with access to the internet after reinstalling windows 7. Before the reinstall worked very well.

  I can connect to the local network without problem, and it shows that the internet is connected. Yet I can not access the internet. When I disconnect and reconnect, I get a few seconds of internet work before it stops working.

  When a diagnosis in the network and sharing Center, I get the error "default gateway is not available" and occasionally "the connection between your access point, etc. and internet is broken"

  Other computers and devices using the network are working properly, although there was a 'competitor IP address' error on another pc, which, after a reconnection, solved itself.

  I use an edimax 802.11n wireless card and a D-link router

  I tried several things to make it work again, but without result. Any help would be greatly appreciated

  disable TCP/IPv6 had no effect.

  I think I can have fixed me, I installed the driver microsoft before the reinstall instead of the driver edimax and internet suddenly started working.

  Thanks for the help of yor

• My connection to the Local network is suddenly missing

  Hello

  Suddenly, I found I can't access my LAN port because I can't found the option to connect to the Local network in network and sharing Center. I also looked in Device Manager, but there is also the LAN card is missing. I don't know why it's happening. The only change I made is configured LAN properties as set as--> advanced--> liaison & duplex speed--> 100 Mbit/s/full duplex. Although I don't know if it has nothing to do with my lack of LAN option, but that's the only change that I made before I see my LAN is missing. then I reinstalled my windows 7 with the hope that it will be recovered, but after the installation of a new windows 7 the problem still persists and also I am very sure that my operating system windows 7 is all ok to install all drivers base because I used the same OS disk for countless times.

  Kindly help me how to solve this problem, because I can't use any Ethernet connection in my computer.
  Thanks in advance...

  The total absence of the adapter is a hardware problem.  Is this a desktop or a laptop? If Office on the motherboard or card adapter?  If it is a laptop or onboard there may be an option to enable / disable in the BIOS which might be worth checking out.

• ASA5505 can transfer clients to remote VPN access to the local network

  I have currently ASA 5505 and 2911-router and I am trying to configure the VPN topology.

  Can ASA5505 you transmit to remote VPN access clients LAN operated by another router?

  These two cases are possible? :

  (1) ASA 5505 and 2911-router are separate WAN interfaces, each connected directly to the ISP. But so can I connect an other interfaces LAN of ASA 5505 in a switch managed by 2911 router customers to distance-SSL-VPN to inject into the local network managed by the router?
  (2) ASA 5505 is behind router-2911. May 2911 router address public ip or public ip address VPN-access attempts have directly be sent to ASA 5505 when there is only a single public ip address address available?
  Long put short, ASA 5505 can inject its clients to remote-access-VPN as one of the hosts on the local network managed by 2911-router?
  Thank you.

  I could help you more if you can explain the purpose of this configuration and connectivity between the router and ASA.

  You can activate the reverse route on the dynamic plane on the SAA. The ASA will install a static route to the customer on the routing table. You can use a routing protocol to redistribute static routes to your switch on the side of LAN of the SAA.

• Easy VPN not able to access the local network

  Hi guys,.

  little hope can help me, I'll give you a run down on the config.

  I have a border router that is a no. 2851 connected to the No. 2851 is a switch cisco 3750 running Routing inter - vlan with four VLANS.

  I have easy VPN server on the edge router No. 2851 I am able to connect remotely from a client vpn cisco with a problem but I can't access the local network on the server, I tried everything with no luck.

  I have a cisco VPN client installed on a 64-bit windows system 7 and I also tried with windows xp 32-bit system and still no luck.

  Please I need help I need to get this race to end of trading today.

  I will be copying and pasting the edge router config please if someone get review and see if the config is good.

  You need to change your ACL PAT of standard to extend and to deny traffic to be translated to the Pool of VPN:

  access-list 120 deny ip 10.10.10.0 0.0.0.3 10.10.50.0 0.0.0.255

  access-list 120 deny ip 192.168.XX.0 0.0.0.255 10.10.50.0 0.0.0.255

  access-list 120 deny ip 172.16.XX.0 0.0.0.255 10.10.50.0 0.0.0.255

  access-list 120 deny ip 172.1X.20.0 0.0.0.255 10.10.50.0 0.0.0.255

  access-list 120 deny ip 192.168.XX.0 0.0.0.255 10.10.50.0 0.0.0.255

  access-list 120 allow ip 10.10.10.0 0.0.0.3 all

  IP access-list 120 permit 192.168.XX.0 0.0.0.255 any

  IP access-list 120 permit 172.16.XX.0 0.0.0.255 aniy

  IP access-list 120 permit 172.1X.20.0 0.0.0.255 any

  IP access-list 120 permit 192.168.XX.0 0.0.0.255 any

  overload of IP nat inside source list 120 interface Dialer0

  no nat ip within the source of the list 1 overload interface Dialer0

  clear the ip nat trans *.

  Hope that helps.