Is pigmented or coloured cartridges HP ink?

Similar Questions

• HP Photosmart 7520 inserted new cartridges, toner ink drops photos

  My Photosmart HP required in new cartridges, I have inserted four new and the printed photos smeared ink; the ink is out on our fingers.  Put old cartridges check, printed in pink.  Reintegrated new cartridges, printed photos still smeared ink.  Please notify.  (I got these cartridges from the HP site).

  Hi @biblebabes,

  I understand that you have replaced the cartridges and the photos are forthcoming from smeared. I can help you with this.

  I have a document with a few steps to try to see if this will solve the problem.

  The streaks of ink fixing, faded prints and other common print quality problems.

  Here is information on how to manually clean the cartridges.

  "Ink cartridge problem," "Incompatible cartridge" or "Ink cartridge failed" Message Displays o...

  This document provides details to manually clean the print head.

  "Missing or doesn't have a printhead" Message appears on the control panel.

  What operating system do you use?

  Mac OS X: how to find which Mac OS X Version is on my computer?

  How to find the Windows Edition and the Version on your computer.

  Try to print on plain paper to see if you have the same results if you use a different type of paper.

  What kind of paper do you use?

  What have been the results of the diagnostic Print quality report?

  Good day!
  Thank you.

• 190 HP colour copier: align ink cartridges

  I have a copier HP color to the old address 190 - it has been little used and very well taken care of. Since the new ink cartridges won't beyond the alignment of cartridges. I did it about 10 times - all suggestions on what do I do, I can solve this problem and use the TI - Tx

  Try below steps help bypassing the alignment:

  Hold the "Enter" button and press "Menu".

• OfficeJet 5470 e-all-in-one: Subscriber instant - problem with #62 color cartridge - Cyan Ink only

  I just installed a new color cartridge and our copies look right.
  
  I aligned the printer and then cleaned them (the two cleanings) and Print quality Diagnostic report shows nothing in the column "Cyan".
  
  Is it possible that the cartridge is defective?
  
  Thank you very much for your help!

  Hi @fiveinthetree,

  I understand that you are having some print quality problems with your HP Officejet 5740. I'll be happy to help you.

  It is possible that the cartridge you received is defective, however, there are some troubleshooting, you need to try before you can replace as defective cartridge.

  I recommend contacting instant ink 1-855-785-2777 for support in real time with an agent. If they determine that the cartridge is defective, they can help you with the replacement.

  If this help will testify of my answer by pressing the 'thumbs up' below, or click on the button "Accept as Solution" if I helped you reach a solution.

  I hope this helps and have a nice day.

• HP officejet pro 8210: hp officejet pro 8210 - locking cartridge tab ink broken

  When you remove the black ink cartridge, I seem to have broken the small plastic tab in the bin to which the cartridge is inserted. Where can I get a replacement? I have no idea of the number or how to identify it.

  Hi @Balmoral,

  Welcome to the HP Forums!

  I understand that you have a broken with your printer HP Officejet pro 8210 part. I'm happy to help you!

  Please Contact HP phone supports for your hardware options. (After you fill out the information, you will receive a phone number.) If you do not live in the United States / Canada region, please click the link below to get help from your region number. Language-country selector.

  Do not forget to return to this topic and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I hope that this post helps!

• HP Photosmart C4280 all-in-one: what hp printers use ink 74 & 75? Buy new ink if my C4280 always says 'no cartridge detected ink?

  This printer has worked well in the past. It is a bit old. I used one that has a fax for a while, but after I have does not need that 1, I put this 1 upward again... maybe a year ago? Recently, it does not recognize the ink as being installed. I think I bought cartridges 74 & 75 maybe 2 months ago so that they are fairly new. I looked at the help on this forum and tried from the back and then pull the plug out for 15 seconds and connect again... no help. I read how to remove the cartridges and where the cartridges go in... no help. I even unplugged from the rear and the plug for 20 minutes... no help.

  I read somewhere on this forum without other printers use 74 & 75 ink (or was this one of them?). So if I had to buy new ink and is not the problem...?

  Can someone help me?

  Thank you!

  Hello

  The following change can help:

  http://WWW8.HP.com/au/en/PDF/HP_Printer-to-cartridge_compatibility_guide_tcm_184_1233104.PDF

  Kind regards.

• OfficeJet Pro 8600: just installed new HP cartridges and ink colors are disabled!

  It's very expensive 4 950 XL and 951 cartridges XL that I bought at Staples a couple of months. I noticed right after installation that bright red in my images were now feel like dull brown. I printed a few pages from the control panel of the printer test. Cyan and yellow seemed pretty accurate, but magenta was a deep purple, not the lightest color pink or pink, I expected. I think that something was wrong with the series production of this cartridge. I hope I can find my receipt, but if not, always wait that HP would replace a full cartridge that was flawed in manufacturing. My HP printer has an accuracy of colors great until about a week ago, but is now almost useless for the work at home that I want to do - for example custom greeting cards, cards, posters, etc.. I printed the test pages don't show any problems with the alignment of the head, and the stripes of color show no scratches. Just a magenta that is close to her correct hue, based on my long experience with color ink jet printers.

  An HP service technician spent 1/2 hour on the phone with me yesterday, and we could not solve the problem. I had already worked through the steps that you referred me to. I have never known or heard of a problem like this, and had not the technology. When I printed the Diagnostic Page of print quality, I have absolutely perfect alignment and bars very clean black, gray and colors. Yellow and cyan looked quite right. Magenta was a deep, dark - purple not magenta I am familiar with years of work with inkjet printers. But it's printed cleanly, I started to believe that the new magenta cartridge, which had just been installed as well as 3 other XL cartridges, had somehow got filled with dark purple ink. However during our tests, asked me to remove the magenta cartridge and pick up some color from around the beak with a Q Tip. When I rubbed on the print paper, it was true magenta!

  Other theories were: (1) that somehow the circuit board of the printer and print head did not and triggers the two nozzles magenta and cyan times reported magenta printing. That seems the most likely answer. 3 the theory was that the ink in the print head channels had a leak between inks cyan and magenta. It seems less likely, because there is no impurity in the print cyan, as well as the color printing was absolutely consistent over several test pages. The tech asked me to remove the print head Assembly and clean the area around the nozzles. That did not help.

  In the end, I was offered a model of printer a HP refurbished more recent than mine. The price was very reasonable - much less than the cost of a printed circuit board or a feeling of head. He also used the same cartridges, so my XL series would be used later once provided with the new printer cartridges are consumed. I took that offer and hope to have a new printer from Tuesday. So I'm glad HP service.

• HP 564 inkjet cartridge: new ink cartridges do not work

  I have trouble finding just the photo black ink cartridge.

  When I look at the package (online) I don't see if the cartridge is for photo or regular black

  I would like some advice on how to order just the photo black cartridge

  Thank you for your help.  I need a lot of help because I'm 80 years old.

  564 or cartridge 564xl photo can be ordered from HP HP SureSupply siteonline.  here document contains information on how to tell the Photo black cartridges cartridges in the store.

  Figure: Ink cartridge Photo with the camera logo

• HP Deskjet F370: Is it possible that a printer can t be detected by a computer because it has no cartridge or ink?

  I have a 3-in-1 printer. I plugged it to my computer and my pc didn't have any reaction. However, there is no cartridge. I tried the scanner that doesn t require ink and it didn t work too. When I press the "scan" button, the power button started blinking and the ink light became red with an exclamation point. I was told that the scanner is still usable even without ink and cartridges.

  I tried to install the HP software should detect my device and it cannot be detected, so I cannot continue with the installation.

  Hello!
  Welcome to the HP Forums, I hope that you are @Jen25,

  I noticed your post on disorders that you encounter some scanning with your Deskjet F370 without ink cartridges and wanted to respond with my own suggestions. I would say that if the printer is showing flashing lights, such as: Burkina Faso / ink installed, then this puts the printer in an error state. If the printer is in an error state, it generally causes problems during analysis and installation of software until the hardware problem (the ink is replaced) is fixed.

  In the end, my suggestion would be to replace the ink and try to analyze and to install the software again and it should work.

  If you have trouble, let me know and I'll do my best to help.

  Hit the "accept as Solution" if we reached a solution and the "thumbs up".

  to say thank you for my help.

  Have a wonderful day

• printer will work if the color cartridges are ink

  I have an Officejet 4620. My computer says all the ink cartridges are out of ink. I can always print in black. I need to replace the color cartridges?   The printer uses individual cartridges for red, blue and yellow cartridges. Color will be printed in blue and yellow only, so I guess there is little color left.

  I usually do not need color copies and I have another Copier.

  Hello @Connsu,

  Welcome to the Forums of HP Support!

  I would like to help you today with your color cartridge application today. Because your printer uses four cartridges: HP 564 black, HP 564 Cyan, Magenta 564 HP and HP 564 yellow, if one or all of these color cartridges are exhausted replace them to continue using the printer. Your HP Officejets ink system is designed to print when have all ink cartridges. A little ink in each cartridge is used for maintenance and maintenance tasks completed by your printer to keep the print head system in your printer in good working order.

  The print head is the part that the cartridges will fit. It controls the "reading" of the cartridges and put the ink on the page. If the printhead is not able to perform regular maintenance, due to depleted cartridges, there is a chance that the mechanism of the print head gets dirty. If the printhead is damaged in any way a whole unit replacement may be necessary. For more information about using ink please click here.

  In the future, if you mainly print in black from the computer, you can set your printer driver to use black ink only. Normally when you print from your computer files will be sent to your printer as "images". If your printer "thinks" it prints an image file that ink color will be used to enrich the black ink. If you don't want that to happen, you can enable grayscale printing option.

  • How to set grayscale in Windows:
  1. Click on the Start menu
  2. Click on devices and printers
  3. Right click on your printer and select Printing Options
  4. Click on features or Advanced
  5. Select the Grayscale dropdown and replace Black Ink only
  6. Click apply and OK

  If you ever want to print in color that you just open the document to print, click Properties in the print dialog box and change black ink only on OFF. This setting only will change to print one job and will return to black ink only for future jobs.

  • How to set levels of gray on Mac:
  1. In the software application, click print
  2. Select your printer
  3. Click Paper Type/quality menu
  4. Click the triangle next to Color Options
  5. In the color menu, select Grayscale or black & white
  6. Select the printing black only ink cartridge
  7. Click print

  Please let me know if the information provided solves your color cartridge problems. I look forward to hear from you!

• New cartridge without ink

  Do you think what would happen if I put in a new cartridge, which I did several times (black), that everything on the PC says that the cartridge is new and full, but still it refuses to print black ink?

  Things worked... not with the printer, but HP.  I called, made a host of trouleshooting, still does not work.  They sent me a refurbished!  A lot!  I heard that it is a common problem.

• HP Envy 5530: Tried everything incl. soaking of cartridges of ink, but still blank to print page

  Printer says it all works well and the ink levels are almost full. Printer sitting idle for about 8 months. Any help would be appreciated.

  Hope you have changed all the cartridges.  Hope for the best...

  Try here.

  http://support.HP.com/us-en/product/HP-envy-5530-e-all-in-one-printer-series/5304881/model/5304882/document/c03765731/

  Let us know.

• HP 60XL black ink cartridge: bad ink

  Hello, no problem with the impression that a few days ago.  Ink quality is poor.  Have aligned, cleaned the printheads, go to the page "print and scan the doctor"... both black and color cartridges are about 90% full.

  Is it possible to remove the cartridge and reinstall it?

  My printer is a HP Photosmart... D110A all-in-one... bought in February 2011.  Works very well.

  Thank you.

  Hi @gator74,

  Welcome to the Forums of HP Support!

  I see that your HP Photosmart Wireless all-in - One Printer, prints in poor print quality. I would be glad to help and don't forget to come back to this thread and check "Accept as Solution" if I helped successfully will solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I understand that you were part of the troubleshooting already. Looks like you have dirty/defective ink cartridges or there is a problem with the distribution of ink system.

  Please use this guide to try to resolve the problem:

  • The problems of print quality for the printer series HP Photosmart e-All-in-One (D110a and D110b)

  If the problem persists and the cartridge is no longer under warranty, you can try the solution proposed in this video. Please use are at your own discretion.

  Video: 7 ways to clean blocked clogged ink cartridges

• Fill the cartridges of ink on deskjet 9800. Red light flashing, won't print. Always worked before.

  Your Question: I haven't found new, original HP cartridges for my deskjet 9800 in any store. I so did my ink on deskjet 9800 as I did with success several times in the past. Two red lights keep flashing. It won't print. [Someone suggested that I need a new print head?] What should do? thanx

  The coding strip only should be cleaned if there is a problem - it is very fragile and can be damaged, making the printer inoperable.  There is a post here that describes how do to clean the MICR band, but respect the warnings and don't do it unless necessary.  There is also a post here that shows how to solve one of the problems mishandling can cause.  Do not clean the Strip unless necessary.

  The coding is the band one located just behind the stem of transport semi-claire. It aims to help the print cartridge faithfully keep track of its position as it moves along the stem of transport. Sometimes dust, ink or oil can accumulate on this strip and cause the following problems:

  • Prints "stairs" to the bottom of the left margin of the self-test page.
  • The margins left or right of the self-test are not properly placed.
  • Ink cartridges carriage slams on the left side of the printer.
  • Automatic test double-print or obscured shows the letters.
  • Defects to flow the length of a printed page (portrait orientation), or on the whole page (landscape orientation).
  • Printing stops and the lights of the Control Panel on the printer indicate an error.
  • Gaps appear in the printed text or images.
  • Slow printing

  CAUTION:

  Do not clean the strip of coding for the following symptoms: media pick questions, paper jam tilt, ink cartridge, missing points or rejection white stripes with printing and smeared or streaked black ink.

   

• How do the "black cartridge grayscale ink only" by default for my C7280 all-in-one

  I have Windows 7 64 bit.  I made the change in devices and printers under Advanced, default print, this option, but when I try to print and look at the properties by default is on the color.

  To print the black ink only follow the steps below.

  1. Select Start menu
  
  2. go into devices and printers.
  
  3. right click on the printer, select printing preferences
  
  4. in the lower right corner, select Advanced
  
  5. and then under features of the printer select print grayscale a dropdown list will appear to black ink only.
  
  
  
  Let me know how it goes.