Is the nessicary to hard drive...

Similar Questions

• Satellite L70-A-139 - guaranteed zero when removing the cover for the RAM and HARD drive

  Hi all

  I have a Satellite L70-A-139 youcef.
  And at the back of the laptop, there is a cover that is fixed with a screw.

  Wil I void the warranty when I unscrew and take a look?
  I want to upgrade my HDD to SSD.
  The motherboard supports Sata III: D.

  Thank you!

  No, the mandate must still be valid.
  There is a removable cover at the bottom of the unit as shown here:
  [Toshiba Satellite C70 / C75 / C70D / C75D / L70 / L70t / S70 / HARD S70t drive replacement procedure | http://aps2.toshiba-tro.de/kb0/CRU3703HG0000R01.htm]

  Then you should be able to upgrade the RAM and HARD drive.
  I think this info should be mentioned in the user manual too.

• Satellite P100-354: how many rpm has the 160 GB hard drive

  How many rpm has the 160 GB hard drive?
  And. It is a SATA?

  Hello

  to answer your questions:

  The disc has a speed of 4200 RPM and YES it s a SATA drive.

  Hope I could clear your mind. :)

  See you soon

• Satellite M40X-112: can I use the 160 GB HARD drive

  I have a Satellite M40X-112 lapptop and I want to upgrade my 80 GB to 160 GB internal drive.
  How is know possible? (Toshiba hotline cannot give me an answer only that a 80 GB drive has been tried with these lapptop!). Anyone have experience with that?

  I read several statements here in the forum about HDD upgrade on the M40X and it seems that there is a limitation in the BIOS.
  The BISO will not recognize the 160 GB HARD drive and that is why you will be not possible to install an OS or you will not be able to boot from this device.

  Please use the "advanced search" from this forum to find discussions on upgrading the HARD drive.

• How to set the password for HARD drive?

  Hello

  Could someone help me please by setting the password for TOSHIBA STOR. E ART 3 (1 TB 2.5 ") HARD DRIVE?

  Hello

  I n t have this external HARD disk, but Toshiba pre-installed some additional software on this subject for the creation of HARD drive password?

• Satellite C650D-112 - reinstall Win 7 after the failure of HARD drive

  The 320 HDD on my C650D-112 18 months, failed last week.
  I replaced it with a 128 GB SSD and it now boots into Windows 8 preview in about 10 seconds!

  I have a copy of the disk HARD original including the recovery of HARD drive Partition, but no recovery disk.
  I can't reinstall drive would work I had been a responsible adult and created the disk when the laptop is new because the disk is smaller.

  Is it possible to reinstall the original Windows 7 Home Premium operating system of the copy of the HARD drive recovery Partition?

  > Is it possible to reinstall the original Windows 7 Home Premium operating system of the copy of the HARD drive recovery Partition?

  No, to my knowledge, this is not possible, even if you copy the contents of the recovery of HARD drive on the new partition on the new HARD drive, HARD drive recovery option does not appear in the advanced boot menu.
  So, it seems you need to order a new drive to get here:
  http://backupmedia.Toshiba.EU/landing.aspx

• Available to add the second internal hard drive to 17-e117dx

  Hello

  Can you let me know, if there is provision to add the second internal hard drive for HP Pavilion e117dx 17.

  If so, one) is there requirments or the specifications of the hard disk (any make or model); (b) what equipment will be needed and where I can get to and c) Finally will be doing so make sure the warranty of my laptop HP Sub

  HP Pavilion

  Product: F9J38UA #ABA

  Model: 17-e117dx

  Thank you

  Not in the way you probably do. Here is the Service Manual:

  Manual

  See Page 50. Unlike the Envy 17 and Pavilion dv7, Pavilion 17 has that a single hard drive Bay. The only way to add a second hard drive is to remove the DVD (optical drive) and insert a DVD to the hard drive bay adapter. The manual shows how to remove the DVD player and you can buy the adapter at amazon.com or jacobsparts.com. Note that this is a 9.5 mm thick disc, not a 12.7 mm. Both types are available. I do not recommend the adapter DVD player solution because you lose the use of the optical drive, and also because the interface of optical drive is usually not as fast as the main hard drive interface. Always fast enough for simple storage and you can run a video of her, but you do not want to edit the video of this disc, for example.

  https://www.jacobsparts.com/items/HDDBAY-02/

  If you decide to go the route of adapter DVD I would buy a large capacity 5400 RPM SATA 2.5 inches wide and drive hard thickness 9.5 mm. No sense in buying a reader more expensive high-performance.

  http://www.Newegg.com/product/product.aspx?item=N82E16822178006

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Qosmio F10 - cannot change the type of HARD drive in the BIOS

  I want to change my hard drive, but the category in the BIOS is not editable.

  I can not change the type of hard drive in the BIOS on my desktop PC.

  Hello

  And you want to change in the BIOS now?
  I put t know which option you mean exactly

  The drive in the BIOS, you can change t. That's why you should buy a new

• Low beginning on Satellite M40-145 after changing the 160 GB HARD drive

  Hello

  I own a Satellite M40-145 since 2005. After more than two years without any problem, two weeks ago the 80 GB hard drive to the original address has been damaged. So I had to replace it with a new, 160 GB (this replacement was made in a store because it's out of warranty).

  I used successfully on the new HARD drive recovery CD to install Windows XP and all the drivers (just as when it was new).
  I used Partition Magic to create a partition of D for data. Also, I installed Office 2003, Norton 360 and connected to the Internet.
  It worked quickly with only small problems than perhaps with little patience I could fix: as this Bluetooth hardware is not detected and the wireless switch began with the lights off even being in the position we (it worked with new just switching out-lit again). But suddenly, after only one day of use, Windows starts became very slow. It takes about 4-5 minutes until it is possible to use the laptop.

  Now, I tried many possibilities to solve the problem, but always ending on the same problem: I used the recovery CD again and try to use the computer with or without updates (I thought that maybe the problem was due to a bad update), with and without Internet access, etc.
  I also tried in vain the program Microsoft Bootvis to try to speed up the startup, etc.

  I even created an image with Acronis to only with XP and Office running fast, so that I could install it again and try new things.
  I also tried to clean the registry with various programs like CCleaner, TuneUp 2008
  Also the defrag JKDefrag and PageDefrag. But always returning to the same problem after a few days of good conduct.

  I don't know what else I could do. I wonder if maybe the new HD is damaged (although I test and no error or no damage was detected) or if the update BIOS might resolve this problem (I'm not and that's a big risk).

  Please, could someone help me?
  Thank you very much for your attention.
  Pablo

  In my view, that there is nothing wrong with the software or all drivers on you laptop.
  I think the key is the enormous size of the HARD drive.

  The difference between 80 and 160 GB is huge.

  To my knowledge, the BIOS supports a limit on the size of HARD drive and I really wonder why the 160 GB HARD drive has been recognized by the BIOS.

  However, I think you should test a 100 GB, 120 GB HDD if the same question perhaps if poster using a HDD a size smaller.

  Best regards

• M60: Question about the speed of HARD drive

  Hello

  does anyone know what RPM disk hard m60 turns to?

  That means Smart in the specification of HARD drive?

  Thank you very much
  Panos

  Panos Hi,

  In my view, that the hard drive in the M60 turn 4 200 RPM.

  S.M.A.R.T. means Self -Monitoring hasnalysis and Rinputs of technology. A system in which the hard drive can monitor his own health and report on potential failures before they occur.

  Kind regards

• laptop Compaq CQ58: id of failure to the dst short hard drive RGF0R0

  my notebook Compaq CQ58 3 year, husbands, froze and wouldn't respond, after a few hours I force it down by pressing the power button, when I tried to start it up again once he went int automaticic repair, it took more than 24 hours.

  but the computer continues to freeze and go into the auto repair each time and was unusable.

  I don't have a recovery disk, none came with the computer and stupidley has not created a when the computer was new. being the only other computer that I have a windows vista I could not create one on this machine.

  As their was anything important stored on the computer I decided to reset the computer hoping that would solve the problem.

  I followed the instructions and the computer seems to be going through the motions to reinstall when he got stuck in a loop of

  the HP points logo swirling

  a popup with the date and time and please wait

  a white screen with the top of the window cmd at the bottom left of the screen

  back to points logo and swirling HP

  a popup with the date and time and please wait

  a white screen with the top of the window cmd at the bottom left of the screen

  After 48 hours I force crashed computer

  I ran the race test that everything happened except the short DST hard drive

  Falure ID: RGF0R0 - 69781:-MFKT1F-60WU03

  This means that the hard drive needs to be replaced and if so should I also a recovery disc, the laptop is out of warranty

  Thanks in advance for any help

  Fiona-s wrote:
  
  

  I ran the race test that everything happened except the short DST hard drive

  Falure ID: RGF0R0 - 69781:-MFKT1F-60WU03

  This means that the hard drive needs to be replaced and if so should I also a recovery disc, the laptop is out of warranty

  Thanks in advance for any help

  Hello Fiona-s,

  Thanks for posting in the Forum of Support HP!

  I'm afraid that the HARD drive has failed - the question is material one and all simply restore/reinstall will not solve it. Yes, you need to replace the HARD disk new or better with the SSD. SSDS are up to 10 times faster than hard drives:

  > http://ocz.com/consumer/ssd-guide/ssd-vs-hdd

  > https://en.wikipedia.org/wiki/Solid-state_drive

  There are more than 100 manufacturers and sellers SSD, but personally, I would choose Samsung, Intel, Toshiba, or OCZ ones.

  Microsoft Windows 7, 8.1, and 10 have supported for SSDS. Vista and XP - no

  You will need a recovery media to restore the windows once you have installed the new SSD or HARD disk.

  You can get possible by contacting HP Support. Here's how:

  > http://support.hp.com/us-en/document/bph07143

  > http://www8.hp.com/us/en/contact-hp/contact.html

  > http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html

  Feel free to post if you have any other questions.

• Is it possible to change the 500 GB HARD drive with an SSD on my HP Pavilion MS228sc?

  I wonder if it is possible to change the 500 GB HARD drive with an SSD on my HP Pavilion MS228sc?

  If 'yes', I guess I have to go for a SATA SSD if there is. But I have to worry about other specs?

  If 'Yes'... what could be.

  I googled my question but no answers... so I ty Wizzards :-) Forum

  @Lord_Nikon

  In fact, this is not true. As long as he uses a large SSD enough it will be able to use the recovery media. I suggest using a SSD of 256 or 512 GB if budgeted for the upgrade...

  He doesn't have to make a Windows 7 installation USB drive and use the activation key license on the certificate of authenticity from the PC Windows to perform a cleanup to install.

  One of them should be on your PC. The Prodct key is what is needed for installation and activation online.

  

• Cursor flashing at the start of the system and hard drive not working do not on the other computer

  Original title: I need help with my Hardrive

  Recently I had problems with a hard disk of computers. So I'm going to give guys the full story, I fell on this computer, it's actually my mums computer and it had a blue screen at startup error. I'm sorry, but I don't remember that the error was called on the top of my head, basiclly I quikly searched online and alll they say should use fixboot. So I did and the computer booted Windows XP very well. So the next day, when I was starting the machine (just to let you know, it would be the first start since I used fixboot, other than the right after that, I don't know if it would make a difference).

  In any case, while trying to start, there was just a slider, or as underscore that retain just flashing in top left corner. I thought that maybe I should reinstall windows on another partition so my files would be safe. I did it, the installation program had no problem with it, but when I booted up I got the same line of flashing underscore / cursor in the upper left corner.

  I thought that maybe I should back up the hard drive using my other computer so I tried to plug in the hardrive in my work computer and the hardrive started to heat up and as if it worked but any hardrive was getting into my computer, I refreshed it, started the computer upward once again, nothing.

  So my question is what is the problem with this hardrive and how I save? I'm ready to do anything, use the live CD, using another computer. I have precious moments of family on the hardrive.

  Thank you guys

  Hi Joemost,

  As you have important data on the hard drive. We recommend that you contact the vendor of hard drive to diagnose hard drive or visit the nearest tech store to save your data.

  There are chances that the boot files are missing on the computer and also you could have not connected the hard drive as a slave when you connected to the other computer. Once you have saved the data, you can repair the existing windows and check if it starts successfully.

  Try these steps to repair install Windows XP:
  a. start the computer using the XP CD. You may need to change the boot order in the BIOS OF THE system for the CD starts before the hard drive.
  b. on the "Welcome" screen, press ENTER to start the installation of Windows.
  c. accept the license agreement and Windows will search for existing installations of Windows.
  d. Select the XP installation you want to repair in the list, press R to start the repair.
  e. the installation program copies the necessary files to the hard disk and restart.  Do not press any key to boot from CD when the message appears. Setup will continue as if it were a clean install, but your applications and settings are preserved.
  f. when the installation is complete, check if Windows starts correctly.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Disk management will not read the 2nd internal hard drive more!

  Hello

  I am a user of windows 7 and later than yesterday (2016_Feb_02) managing disks stopped to read the secondary internal hard drive (it was working perfectly well before). Does CPU, a beep when it is turned on or even rebooted and more when it comes to the windows logo, the PC hangs for a good 15 seconds.

  The hard drive was an external hard drive and I removed the cover must be installed on my PC, but it has worked well for more than 5 months so far.

  I would like to reuse the hard disk without losing any data.

  Information on PC:

  Compaq

  RAM 2 GB

  Purchased in 2009

  Details of the hard drive:

  Seagate

  2 TB

  Please let me know if more information is needed.

  Thank you very much.

  Download SeaTools for DOS, burn the ISO file downloaded to a CD (you can use the free ImgBurn) and boot from this CD.

  http://www.Seagate.com/support/downloads/item/SeaTools-DOS-master/

• HP 6120 t BIOS does not recognize the second IDE hard drive connected via IDE-SATA controller

  Hello

  HP 6120 t (vista) BIOS does not recognize the second IDE hard drive connected via IDE-SATA controller. The other SATA disk and the DVD player came with the machine.

  I hooked my old 200 GB Hitachi drive via the controller. I also put the jumbers in the present as a slave. I also took the original WD drive and just connect the IDE hard drive. BIOS do not show any drive at all.

  I would try something possible at this time I have a lot of my data on the old disk.

  Thanks appreciate any suggestion.

  Try to enter the BIOS and I believe under change of Advanced menu of SATA to IDE or Enhanced.

  You need to do when you install Windows XP or you will get a blue screen and it does not start.

  Don't forget chang back when you put it in your drive home hard sata.