Is the PowerEdge R610 Compatible DELL VMware ESXi 5.1 update 1 recovery Image?

Similar Questions

• using vmware update manager to update Dell M630 ESXI 5.5 update 3

  I use put vmware update manager (VUM) up-to-date Dell M630 ESXI 5.5 updated 3. The Dell build was published on 11/13/15.

  The results of the baseline VUM are attached. I was surprised that some older patches from 2014 are suggested, and even complete full update and 2 update 3. Is a common practice to just update with whataver MUV said, or is it best to get VUM to apply the patches after the date of release of a version of the seller?

  If missing the update you must certainly apply. I'm just going by what suggests Manager Update and apply all the patches.

• Upgrade VMware ESXi 6.0 Update 2 VMware ESXi 6.0

  Hello I am running my PowerEdge T110 II with VMware ESXi 6.0 - Dell customized image. I see that from April 15, 2016 Dell just introduced VMware ESXi 6.0 Update 2 and I'd like to update my system.

  On the download page , I see there is an option to download and the ISO file. I wonder if this installation will completely be wipeout my existing VMware ESXi 6.0 - Dell custom and all the settings and I have to start all over again or update 2 ISO just 'modernize' my network?

  Hello

  You can use it to update without doing a new install. KB.VMware.com/.../Search.do; cmd = displayKC & externalId = 2109711 #Inter

• Installable VMware ESXi 3.5 Update 4

  Hello

  What are the differences beetwen VMware ESXi 3.5 Update Installable 4 and VMware ESX 3.5 Update 4 to the download Web page?

  https://downloads.VMware.com/d/info/datacenter_downloads/vmware_infrastructure_3/3_5

  Is a free stand-alone ESXi, ESX is not. In addition, ESXi lacks a service console.

  Kind regards

  Gerrit Lehr

  If you have found this or other useful information, please consider awarding points to 'Correct' or 'useful '.

• R710/R720 - Dell customized Image of VMware ESXi 5.5 Update 2 - megaraid_sas version specific?

  That I improve a R710 and two v5.5 (Dell image) to v5.5 U2 ESXi ESXi R720 using the image of Dell here:

  www.dell.com/.../DriversDetails

  The documentation "Upgrade Guide to ESXi 5.5 using Dell customized Image" here:

  www.Dell.com/.../manuals

  indicates that a specific version of the megaraid_sas driver must be installed.

  Is the version megaraid_sas that installs with the image of Dell U2 v5.5 not the right version?

  I just ran the upgrade on a R710 and it's the megaraid_sas version installed:

  ~ # vmkload_mod s megaraid_sas | grep Version
  Version: Version 06.803.73.00, build: 1331820, Interface: 9.2 inspired: August 22, 2014

  Thank you.

  Hello

  It lists the R720 and R710 systems supported and both link to the same page, so the customized version is the same for both servers. Is the version listed in the reference guide for A02

  megaraid_sas - 06.803.73.00

  Page 5 ftp://ftp.dell.com/Manuals/all-products/esuprt_software/esuprt_virt_solutions/vmware-esxi-5_Reference%20Guide6_en-us.pdf

  This is the same version that he shows for your installation on the R710 so that seems correct.

• Upgrade of the 3 HP VMware ESXi 5.1 update kills Emulex network and cannot be cancelled?

  People,

  I have a serious issue here after the upgrade of the HP Blade 465 BL c G7 with adapter Emulex NC551i double Port FlexFabric 10 Gb..

  The problem: after the successful online update of ESXi 5.1 Update 2 Patch 5 (2000251) in ESXi 5.1 update 3 (2323236) the ESXi server cannot be crazy, or it can ping to the outside network, so she doesn't have to reconnect to the VCenter server.

  Software/Firmware version:

  The version before the upgrade of the server are:

  ~ # ethtool-i vmnic0

  pilot: be2net

  version: 10.2.293.0

  firmware version: 4.9.416.2

  bus-info: 0000:04:00.0

  ~ #

  Since the version above does not work, I managed to download VMW-ESX-5.1.0-be2net-10.2.477.20-offline_bundle-2541837.zip for upgrade the driver VMNic in: 10.2.477.20 but still after the update and restart the network is not able-ping.

  ROLLBACK:

  I also tried to restore to previous work ESXi Server version 2000251 to the help of SHIFT-R but the ESXi server still restart as 2323236 with a network that still worked.

  
  

  Any other suggestions would be greatly appreciated without having to reconfigure the settings of ESXi and the configuration of the switch distributed from scratch.
  

  According to the recipe of HP/VMware here: http://vibsdepot.hp.com/hpq/recipes/HP-VMware-Recipe.pdf

  There is a note about the NC551i:

  

  / Rubeck

• Dell custom ESXI 5.5 update Manager software

  Hello

  I installed some Dell R710 server custom Dell ESXi 5.1 Version.Now I would update this ESXi 5.5 servers (Dell Version)

  Question: Where can I find as a Dell of ESXi 5.5 custom Version for VMware Update Manager (.zip)

  Thanks for help

  What about Peter

  Hi Peter,.

  You can download the ISO from Dell here:

  www.dell.com/.../DriversDetails

  Be sure to upgrade your vCenter and Update Manager 5.5 before trying to download the ISO (under ESXi images).

• infrastructure VMware esxi 3.5 update

  Hello world

  A production with 5 vm to update ESxi server when it is in production? or, is it better to move the virtual machine to a different server, and then update it?

  The server running ESXi 3.5 and advises the tool update to the newest firmware update and tools

  Thank you!!!

  Peter

  Many updates require a restart of the host.  I always migrate VM before the update, so the reboot will not affect the.  The update of the VMTools restarts if the virtual machine.  Which can be coordinated at a later date if.

  Charles nights, VCP

  If you have found this or other useful information, please consider awarding points to 'Correct' or 'useful '.

• How to activate the RS232 and USB communication on the guest operating system in vmware ESXi 4.0

  I installed a software in the OS (redhat 5.0) invited to vmware, it must communicate with the device via RS232 or USB

  but not to communicate.

  Vmware tools is installed.

  I try to change the attribute of vmware, add the com port and USB, but still, it does not take effect

  What is the RS232 or USB available on the operating system called?

  How to activate RS232 and USB?

  USB and series are not available in a prompt. There are IP network series and usb IP devices that can be used.

• Dell Optiplex 3020 - the black screen after dell logo (happened after windows updates froze at halfway and systems were restarted)

  We had windows updates run on all our systems of windows 7 in our medical center.  13 or so of our 3020 s Optiplex froze for eight hours about in a State of "install updates 1 of 24".  I have all them turned off and restarted units.  Once units have been restarted, they gave the Security windows startup or start-up option normally.  Those who had selected the option to 'start normally' would display the logo dell at startup, then click on a completely black screen (all devices still in market and monitors recording an active signal even if no picture).   Those started in safe mode w/o networking, loaded in safe mode.  I rebooted the machine in safe mode, and they all started out in windows without problem.

  For systems that go completely black after the dell logo.  I am able to F2 in the BIOS, I can run diagnostics from BIOS and I can't F12 in boot options, but I cannot F8 or SHIFT + F8 mode without failure or fact start in safe mode, please come under early start options.

  Anyone happen to know a way to launch a system of 3020 optiplex in safe mode without the use of F8, SHIFT + F8, go through msconfig or remote access to the registry (because I can not remote in the system on the network)?

  Maybe I can put the hard drive in a dock and change the registry in this way?  But can I change the potentiometer to force secure boot? or is it not possible to make a bcdedit to it as an external drive, install it in his camera and force it to safe boot the next time, he is running?

  Any ideas or suggestions would be very appreciated.

  Hello

  Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

  I suggest you to send your request in the TechNet forums to get the problem resolved.

  Please visit the link below to send your query in the TechNet forums:

  https://social.technet.Microsoft.com/forums/en-us/home?category=w7itpro

  Hope this information is useful. Please come back to write to us if you need more help, we will be happy to help you.

• VMware ESXi 5.0 Update 1 breaks AutoStartManager (free license ONLY, waiting for patch/fix)

  Hello

  Today I updated to version 515841 to 623860, apparently, the update was successful.

  However, I noticed something very annoying - the host is no longer automatically starts or stops invited as configured. I tried to turn the feature on and outside, moved to guests to "Manual start" then back to "Auto-start" - with various combinations of these parameters, also restarted host between changes. But, alas, no luck.

  In the list of "Recent tasks" appears in vSphere Client, the Auto Power On tasks as completed, launched by root, with 'Start Time' and 'End time' with the same timestamp. The server log reports the following error (3rd line below):

  2012-03-16 T 07: 08:27.296Z [6DE40B90 info "TaskManager"] created task: haTask - vim.host.AutoStartManager.autoPowerOn - 97171136
  2012-03-16 T 07: turn on/off [verbose 'Hostsvc::AutoStartManager' 6DE40B90] 08:27.297Z 5 VM with delay 120
  2012-03-16 T 07: 08:27.333Z [error 'Hostsvc::AutoStartManager' 6DE40B90] Error initializing PowerOp for VM 5: vim.fault.RestrictedVersion
  2012-03-16 T 07: 08:27.334Z [6DE40B90 info "TaskManager"] task completed: haTask - vim.host.AutoStartManager.autoPowerOn - 97171136 success of status

  RestrictedVersion? Something was happening to the license free ESXi features?

  Someone else with the same problem/a solution?

  Thanks in advance!

  Yes, it's a bug.  It only affects people running the free hypervisor.  Not aware of a fix/workaround yet...

• Backup the DataStore folder & files using Powershell & ESXi 4.0 Update 1

  Hello

  I was wondering if someone could help me to download files from an esxi 4.0 data store to a local directory using powershell.  It's a small VM and I just need the datastore directory copied down every day.

  Any help is greatly appreciated.

  Steven

  Have you tried the cmdlet Copy-DatastoreItem?

• 3.5 VMware esxi

  I have a dell poweredge 2600, I have vmware esxi 3.5 and it has 5 hard drives in raid format

  When I install vmware it shows only 10 gig hard dirve, it must indicate the total amount of 250 concerts

  can someone help me understand why he's not seen the other drives?

  Thanks a lot for your help in advance

  you will need to make your smaller RAID sets, as the limit is 2 TB minus 512 b

  http://www.VMware.com/PDF/vSphere4/R41/vsp_41_config_max.PDF

• VMware esxi 4, 1-tensiond ' AClost power - state alert

  BOM dia pessoal,

  Dell VMware ESXi 4.1 of em um DELL T410 custom EU instalei o, a reference

  ABA na do servidor appears uma mensagem of attentive State.

  "vmware esxi power AClost - alert state" in accordance with na imagem em annex.

  Poderia ser some driver or modulo as nao carregou?

  Abraços!

  Voce ja verificou also is a melting esta devidamente energizada e running? JA tentou dar um 'reset the sensor?

  Por favor, não don't atribuir os pontos para e resposta 'useful' or 'correta.

  Mauro Bonder - moderator

• VMware esxi 4.1 compatibility with ASUS PIKE 2008 interface?

  Hello VM ware Folks,.

  Can you let me know if ASUS PIKE 2008 interface card is compatible with vmware esxi 4.1 since I intend to install vmware server.

  Appreciate your help.

  Thank you

  Srikanth.

  Hi Srikanth,

  PIKE is an exclusive feature of expansion for ASUS motherboards. These motherboards are found in the HCL, but it seems that ASUS has not put the PIKE in the process of certification as a discreet storage card. ASUS claims nor that it is supported on anything other than Windows and Linux operating systems.

  You just have to try it and see, really. I think he's probably going to work perfectly, but it probably is not an adapter of storage supported for VMware ESX or ESXi, if you are having problems.