Similar Questions

• Outref pin the SCXI-1540 module

  Hi all

  According to the manual on the rear connector of the add-on SCXI-1540 is a PIN (19) described as OUTREF.

  It connects directly on spindle AISENSE E series data acquisition cards.

  But there is no mention of this PIN in the manual.

  Is it possible to generate a voltage ref in the scxi 1540 and thus a measure of NRSE on data acquisition?

  Is there any detailed of the circuit diagrams of the module scxi-1540 so that I can see whats up with this PIN outref?

  see you soon

  Frank Greenslade

  Christchurch

  New Zealand

  Hi Frank,.

  So first of all, you can certainly use the Ref Out as your floor floating for NRSE measurement.  If we look at the considerations of field wiring tutorial, he talks about these configurations a little more away.  I have trouble understanding what you're trying to reach beyond that.

• Using the SCXI-1520 module for measurement of torque

  Hello

  I'm working on a project that requires a measument couple in real time on a speed-shaft drivetrain configuration phase.

  I have the SCXI-1520 module, and I think with a with a configuration of full-bridge strain gauge to do this.

  The problem is that it is not possible to connect to a real-time measurement, so my first solution was using some sort of wireless transmission to receive data in the SCXI-1520 module

  The Arduino + Xbee seems to be the best way to go, but at the same time, I think I might have a few problems of conditioning of the signal while transmitting data to LabVIEW through the SCXI-1520.

  Don't you think it's the best way to do it, or is there a better solution?

  Thank you!

  Hi Kenny,

  What type of operating system are you using? When you say 'Real time', do you mean look at a signal when it occurs? If you use communication networks, you will not be able to get truly control in real-time because communication networks is not deterministic, and you cannot guarantee the synchronization.

  If you try to get a signal and he discovers that you buy it, you should be able to use the Arduino and LIFA with LabVIEW. Adding the SCXI-1520 will not add any additional resolution in this circumstance.

  Best regards

  Anna L

• Accuracy of measurement of the SCXI-1100 module

  Dear team,

  I'm figuring an accuracy of measurement for SCXI-1100 (http://digital.ni.com/manuals.nsf/websearch/0790D3C92CF4B16E8625665E00712865) devices.

  It is not described in the standard table, it has precision stage of entry / exit (must be added?). I can't reach a precision which is a result of precision calculator. If you have any equatuions / examples please post.

  Concerning

  Michal

  Hi Michal,

  I'm not sure I understand your question. Are you trying to calculate the accuracy of the SCXI-1100 module, but you do not have the data specification for the calculation, or you don't know how to calculate the accuracy?

  If you need performance data, you can consult the technical data sheet 1100 SCXI. If you want to calculate your accuracy of the device, I can recommend you following KB: How can I calculate absolute precision or the accuracy of the system?

  I hope that this is the info you are looking for.

  Kind regards

  D. Barna

  National Instruments

• entry of mV/psi for SCXI-1102 using the SCXI-1308 module?

  Is there a way to physically connect a mV/psi signal to an SCXI-1102 module, which also uses a block to connect SCXI-1308? What I've read, the terminal block can use only a signal 4-20 or 0-20 Ma, right? I don't see the pins that the terminal block plug to use for output of the pressure sensor mV.

  Thank you very much for the help!

  TQ

  Hi FMC_Pumptest,

  The 1308 Terminal is designed for the current input. You are right that you have entered for 0-20 mA and 4-20 signals my with this block.

  Kind regards

• Rear connector of the SCXI-1520 module as input?

  Good morning,
  
  Regarding connectors on the SCXI-1520, is it possible to use the rear connector as a 68-pin input (instead of an output)? 
  
  I have the following hardware and wanted to know if it's feasible to pipe a signal from an SC-2345 to a PC through the path below.
  
  NI SC-2345 (Signal Cond. Block)  --> NI SCXI 1520 (Universal Strain/Bridge) via 68-pin cable   -->  NI SCXI 1600 (USB Digitizer Card) --> PC
  
  Thanks
     
  

  Hello hma1,

  Unfortunately, you will not be able to do.  The only "entry" would be taken in chassis cascading signals.

• There will be a conflict between the two functional modules of a 2010 Biztalk adapter pack?

  Hello

  We already use a free version of SAP Business Suite (32-bit adapter) to suck SAP data.
  We are now upgrading all SSIS packages with the 64-bit Biztalk adapt pack 2010 and have few questions about it. It works successfully.
  Question 1:
  In my direct SAP, I installed the function module and my old 32-bit adapter works. As part of the migration to the new 64-bit adapter, I give myself with new functional module in SAP that I put in the SAP test area. To migrate all my packages, I have to start to move from one card to the other, and both must function in the SAP LIVE system module. If this is the case, will there be conflicts over the 2 functional modules working for 2 different cards (32 & 64 bit)? If my transition period is 4 weeks, these modules can still work?
  Question 2:
  If this works it cause any impact in the production SAP system at all? I don't want daily data extraction to cause an impact at all.
  Please advice. I'm unable to find any relevant article on this.
  Thank you
  Mani
  Original title: biztalk adapt pack 2010

  Hi Vincent,.

  I would have you post your query in the MSDN forums, because it is addressed to an audience of it professionals.

  Your request would be more out there.

  Check out the link-

  http://social.msdn.Microsoft.com/forums/en-us/sqlintegrationservices/threads/

  Get back to us if you have questions about Windows in the future. We will be happy to help you.

  Thank you.

• How to replace the SCXI-1600?

  Since our IT obliges us to switch to Win7, 64-bit edition, our SCXI-1600 becomes unnecessary because there is no 64 bit driver (Sidenote: the device is still available in the online catalog without obvious by the lack of such a driver warning). in an another tread on this subject, Seth_B advise

  For example, the USB-6251 device mass termination that provides 5 x faster sampling with 7 x better accuracy, USB 2.0 transfer speeds of data transfer more reliable and is only about $300 more including the cable between the DAQ hardware and the SCXI chassis.

  I need more information - I don't understand how exactly who will replace the SCXI-1600 as a connection to the SCXI block, for me, it looks like an ordinary e/s USB device must connect directly to several types of e/s analog and digital through a CBS. What cable should I connect the chassis SCXI containing other maps, how she will turn upward in MAX - in short: I need to decide if the replacement is more trouble with respect to particular software rewriting labview and other efforts that fight OUR guys to keep the System 32 bits for this testbed.

  Hello MBohnet,

  To avoid work or acquisition of new equipment on your part then I would recommend against your IT Department to maintain 32-bit system.

  If you need to upgrade to Windows 7 64 bit then the 6251 is an option at your disposal to communicate and scanning information of you modules SCXI.

  There are steps for setting this up

  1. Remove the 1600 chassis.
  2. Fix a module SCXI-1349 in the back one of the SCXI modules. Then use an SH68-68-EPM cable (the cable is listed on the pricing for the device 6251 tab) to connect the SCXI-1349 module to the PCI-6251.
  3. Your configuration in Measurement & Automation Explorer would be alike in what concerns the addition of your device, but you will point to the 6251 as the digitizer.
  4. The quote above regarding the (5 x faster sampling rate) applies only when using the USB-6251 in parallel mode.
  5. You wouldn't have to make changes to code with switching on the material element.
  6. Also, if you are not connected to the USB take a look at the PCIe-6320 or PCIe-6341 with the SHC-68-68-EPM cable. They are less expensive than the USB-6251 housing alternatives.

  Kind regards

  Izzy O.

  Technical sales engineer

  National Instruments

  www.NI.com/support

• Calibration of the scxi-1520 and scxi-1314

  I have a SCXI-1000 chassis with the scxi-1520 module and the scxi-1314 terminal block and I was wondering how to do a calibration on it?  What I have to send back them to OR for calibration or I can send it to a local company to perform the calibration?  If I can send it to a local provider, what the procedure would be to calibrate?  According to the manual of the module scxi-1314, everything we do is check the resistance and for the scxi-1520, it performs internal calibration.  Is this correct?

  Ron

  Hi Ron,

  You can send them to OR get these calibrated, or you may have a local company. Manual calibration procedures are available herefor many of our products online. Here are the procedures of calibration of 1314and 1520.

  Other issues on the calibration should be directed to ni.com/calibration.

  Chris W

• On the utility of record pass-protected when the disk is encrypted

  Dear all,

  I recently put my hands on a new internal drive SSHD and decided to quantify using filevault. Keep important documents on my mac, I used to create folders of password-protected using a disk with disk utility image. Now, my question is simple: is there a utility on the creation of these encrypted files as all the disk itself is already encrypted? This would add valuable new protection?

  Thank you very much in advance,

  Richard

  Data sheet: mid - 09 13 MBP "2.26 GHz with internal WD 1 TB SSHD

  If your disc is encrypted, then the only way that anyone (including YOU) can look at the contents of your Volume is to provide your password to disk, which we hope is a long and strong password, not only a short practice. Depending on how paranoid you are, perhaps you fell there is additional value on encryption more away from the additional items. But for extra security, the password for your encrypted disks in addition should not be readily available on your drive any just-encypted.

  Most users have very good success with encrypted Volumes. They manage to protect their records from the person mostly likely to access - themselves. DO NOT ENCRYPT YOUR DRIVE WITHOUT CREATING A RELIABLE BACKUP! The encryption is strong - there is no 'rescue' for an encrypted Volume that goes wrong for any reason, including failure of the drive.

• Why Apple can't do two systems? First of all, we are protected, and the other is free just like android, but in the style of the iOS and Apple needs a request so we can manage and see new products from an application and do not go on this site!

  Why Apple can't do two systems? First of all, we are protected, and the other is free just like android, but in the style of the iOS and Apple needs a request so we can manage and see new products from an application and do not go on this site!

  and I don't know that if Apple make a system more freely, there no need for any device on Earth but iPhone.

  http://www.Apple.com/feedback/

• Need help to remove the protection of the family off account of girls

  I deleted my daughter from my laptop Microsoft account. I had the protection of the family there. How can I get the protection of the family out of his account because she has another account set up and know it required a code to get on his google account?  So I would like to remove the protection of the family so that it doesn't keep needing a code. If anyone can help me please and thank you.
   
  * This thread has been changed so that they the title is a little clearer. It will be also moved to a more appropriate forum hoping to teach you to someone who can answer your question correctly.  Thank you!

  Hello

  What operating system is installed on the computer?

  In the meantime, you can visit the link provided below to remove a parental control account.

  How can I remove parental control?

  Hope the information helps you resolve the issue.

• How can I disable protection of the customer

  How can I disable protection of the customer

  Hi pitellu,

  ·        What antivirus do?

  ·        Is it avant-garde or Microsoft Security Essentials?

  You could disable by using the parameter unless there is that a policy applies by administrator preventing turn he took.

  You can turn on or turn on the firewall in Windows XP, please see the link below:

  http://support.Microsoft.com/kb/283673

  Thank you and best regards,

  Imran M - Microsoft Support

• Cannot install Vista service pack 2 is 800f0a09 error code with the message that there are problems with the driver for dell latitude

  Original title: why I get error code 800f0a09 to upgrade to windows vista service pack 2

  I have a laptop del that is running on Windows Vista Edition Home Premium. I tried to download itunes but it requires service pack 2. Whenever I try to update to service pack 2, I get the message following error code 800F0A09. He also mentioned problems with the driver for dell latitude. What can I do to fix this please.

  Thank you

  Hello

  Please join Microsoft Community where you can find the necessary information on Microsoft products!

  You can not install Vista Service pack 2 and get the error with code 800f0a09 and the message that there are problems with the driver for dell latitude.

  The problem may occur if some of the components of the update are corrupt.

  What is the full error message that you receive?

  I suggest you follow the steps mentioned below to check if the problem is with the update components:

  Method 1: Reset the update components

  See the site:

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

  Warning: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 2: Run the system update readiness tool

   

  See the site:

  System update scan tool corrects errors of Windows Update in Windows 8, Windows 7, Windows Vista, Windows Server 2008 R2 and Windows Server 2008

  http://support.Microsoft.com/kb/947821

  Method 3: Turn off the antivirus software

   

  See the site:

  Disable the anti-virus software

  http://Windows.Microsoft.com/en-in/Windows-Vista/disable-antivirus-software

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  I hope this helps. If the problem persists, let know us and we would be happy to help you.

• Flash drive, write protected after the use of Ready Boost

  I have a 8 GB USB flash drive, and I've been using ~ 4 GB for Ready Boost for quite a while now. When I tried to write something on the drive recently, I get a message saying that it is write protected. I tried to change the size of the cache, but has nothing - no error and no change. Tried turning off RB for the drive and nothing. There is no protection switch on the drive, so nothing to break. Tried to restart, refomratting the drive - no joy.

  Only, I could get a new drive because they are so cheap, but this one has a MicroSD in it like a separate disk drive, so I would keep

  Hello

  You can remove your usb flash drive write protection using the method below:
  a. open the start menu, in the search bar type regedit, and then press ENTER. This wil open the registry editor.
  b. navigate to the following location:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\StorageDevicePolicies
  Note:
  If StorageDevicePolicies registry key does not exist, you must create it manually.
  c. highlight StorageDevicePolicies, and then create a new DWORD called WriteProtect (32-bit).
  d. double-click the registration key in the right window, and then set it to a value of 0 in the value data box
  e. press OK
  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/ ) how to back up and restore the registry in Windows