ISATAP adapter reports "tv_ConfigMgrErr31".

Similar Questions

• I have problems with Microsoft 6to4 adapt reports tv_configmgrerr31 and also microsoft PS/2 mouse bring tv _ configmgrerr24

  Workin

  Symptom:	Device is not working properly. Windows cannot load the required device drivers.
  Cause:	A device has a configuration issue preventing it from working correctly.
  Details:	The device, the Microsoft 6to4 map, reports "tv_ConfigMgrErr31". This device won't be available until the problem is resolved. The Plug and Play ID for this device is ROOT\ * 6TO4MP\0004.
  Resolution:	1. check that the correct driver is installed.
  2. try updating the drivers using Windows Update.
  3. check with the manufacturer for an updated driver.
  4. try to uninstall and reinstall the device using Device Manager.
  Partners:	Explanation of generated by Device Manager Error Codes
  Manage devices in Windows
  Symptom:	Device is not present, not working not properly, or does not all its drivers installed.
  Cause:	A device has a configuration issue preventing it from working correctly.
  Details:	The device, Microsoft PS/2 mouse, reports "tv_ConfigMgrErr24". This device won't be available until the problem is resolved. The Plug and Play ID for this device is ACPI\PNP0F03\4-14DDEF44-0.
  Resolution:	1. check that the correct driver is installed.
  2. try updating the drivers using Windows Update.
  3. check with the manufacturer for an updated driver.
  4. try to uninstall and reinstall the device using Device Manager.
  Partners:	Explanation of generated by Device Manager Error Codes
  Manage devices in Windows

  Hello

  This error may occur if one or more of the following conditions are met:

  (a) there is a hardware problem or a new driver might be needed.

  (b) devices remain in this State if they have been prepared for removal. After you remove the device, this error disappears.

  Step 1: If the device does not work, make sure that the device is properly connected to your computer. For example, make sure that all cables are correctly installed, or that the cards are properly housed in their locations.

  Step 2: Run the following Microsoft Fix it.

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

• Norton 360 diagnosis reported: Microsoft ISATAP Adapter #2 is malfunctioning and windows cannot load the drivers required - code 31.

  Original title: ISATAP adapt #2 does not properly. How can I solve this problem?

  My Norton 360 diagnostic report detected a hardware device unusable.  The device type is: Microsoft ISATAP Adapter #2 and the device situation mentions that it is working properly and windows cannot load the drivers required - code 31.

  I think that it is also affecting my internet connection and disrupt its speed.

  Can you please help with this question?

  Thank you very much
  Tony

  Hi Tony,.

  You can try reinstalling the device driver and check if it works.
  Uninstall and reinstall the device in Device Manager.
  a. Click Start, type devmgmt.msc and press to enter.
  b. Locate the Microsoft ISATAP Adapter device
  c. right-click on the device and select uninstall
  d. restart the computer and check.

  You can also consult the following article:

  On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
  http://support.Microsoft.com/default.aspx/KB/932520

  Hope this information is useful.

• Map Microsoft 6to4, reports "tv_ConfigMgrErr31".

  Original title: windows vista device drivers Symptom: Device is not working properly. Windows cannot load the required device drivers. Cause: A device has a configuration issue preventing it from working correctly. Details: The device, the Microsoft 6to4 map, reports "tv_ConfigMgrErr31". This device won't be available until the problem is resolved. The Plug and Play ID for this device is ROOT\ * 6TO4MP\0009.

  Hello

  Please answer these questions so that we can properly diagnose the problem:

  1. when you receive this error message?

  2 are you able to connect to the internet successfully?

  3 is the performance of the computer affected in any way?

  Let us try this method to resolve this error message:

  Uninstall and reinstall the driver and see if the problem is resolved.

  Step 1: Uninstall the driver.

  To do this, follow these steps:

  a. on the desktop, press the Windows key + R and type devmgmt.msc and press enter to open the Device Manager.

  b. expand maps network drive and right-click on the adapter.

  c. select Uninstall and follow the steps prompted.

  Restart the computer when you are prompted.

  Step 2: Search the hardware changes.

  a. on the desktop, press the Windows key + R and type devmgmt.msc and press enter to open the Device Manager.

  b. click Action on the menu bar and select Search the hardware changes.

  Please get back to us with the results.

• n ° 2 of Microsoft ISATAP adapter of attachment

  In the monthly Norton Anti Virus report it is said that it is a device that is not working and I suggest authourise Norton to 'repair' should I go forward?  the said device is a Microsoft ISATAP Adapter #2

  Hello

  Control Panel - Device Manager - do a right-click on the two - UNINSTALL - REBOOT

  Nothing else to do, Windows will do the rest. And you can ignore errors
  If you wish and on some computers, it will always be there but no problem to be expected.

  On a Windows Vista-based computer or on a Windows Server 2008 computer.
  the Microsoft ISATAP map appears with a yellow exclamation mark next to it in
  Device Manager and you also receive an error message
  http://support.Microsoft.com/kb/932520

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• 450 HP: HP 450 Gen 2 Ethernet Driver missing / replaced by ISATAP Adapter After Windows Update

  Good afternoon

  I'm a network administrator at a small not-for-profit organization and aired on a particular issue with our 450 HP Gen 2.  Using Windows Deployment Toolkit, I have an image clean Windows 7 with the applications we want to push on these machines and then followed with update driver using the HP software Assistant.  In general, everything works.  But every so often, a 450 HP decides to 'lose' it's network, which is replaced by up to three non-working ISATAP adapt - hidden driver.  With hidden devices turned off, the Device Manager shows three network wireless, but not ethernet connections.  In addition, the NIC itself is completely dark; no nice little green/yellow lights sparkle.

  This was happening before with an image earlier established by my predecessor, and I discovered that this image was intended to HP 450 Gen1 and Gen2 not - even if the image has been labeled Gen2. Thought it was just a simple matter that the Gen1 image was not compatible with the Gen2 machines.  They would work for a little while, then break after a series of Windows updates.

  So I created my own image, repeat the steps above and for a while thought that the problem has been resolved.  But I just fell on my first 'disappeared' ethernet driver scenario; Since users employing 450 HP are usually off site, they need of working machinery.  But I have not found anything in the forums or through google search to indicate exactly what causes the problem.

  Currently, I use the HP of a DVD Software Wizard because the laptop has no ethernet connectivity to see if that solves it, but I'm interested to know what is causing this problem so I can avoid it in the future.  It's not good if users are bringing back machines to me who... was enough to say... do not work.

  I look forward to your correspondence.

  Best regards

  Robert

  Alrighty, I thought about it.  Essentially, (is no longer editable in the bios) LAN energy saving mode disables the NETWORK adapter, and once off, it will idle rest.  Therefore, your PC will not know to turn it on no matter how many times you restart or connect an ethernet.

  Here's the trick:

  1 unplug the power to your laptop, remove the battery, wait about 1-2 minutes.

  2. connect ethernet port NIC, connect the a/c, insert the battery.  Starts.  You should see your NETWORK card light up.

  3. once in Windows, go to the Device Manager.  You will see that your Realtek NIC listed.  Go into properties, power options and uncheck the option that reads LAN for energy savings.

  Problem solved.  I hope this helps the next guy.

  -Robert.

• Can not find the driver for ISATAP adapter #4

  Original title: ISATAP adapter #4

  This device does not.  Respomse is "Pascal find the driver for this device.

  Windows says I have the latest version of the driver that is already installed

  Microsfir can not find a solution

  Help

  Hello

  Since you have posted in the forum Feedback and specifies your version of Windows
  I had to guess as the operating system. It is best to post in the Forums Windows Vista of answers.
  (Question was transferred in windows - Forum-Other/Unknown).

  Windows answers forums
  http://answers.Microsoft.com/en-us/Windows

  -----------------------------------------------------------------------------------------------------

  For Vista:

  Control Panel - Device Manager - do a right-click on the two - UNINSTALL - REBOOT

  Nothing else to do, Windows will do the rest. And you can ignore errors
  If you wish and on some computers, it will always be there but no problem to be expected.

  On a Windows Vista-based computer or on a Windows Server 2008 computer.
  the Microsoft ISATAP map appears with a yellow exclamation mark next to it in
  Device Manager and you also receive an error message
  http://support.Microsoft.com/kb/932520

  Check the answer by Diana D. here:
  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/a75e8bf1-9a63-4CF4-BF6C-d43a26175959

  I hope this helps and happy holidays!

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Somehow MS ISATAP Adapter has been removed from the Device Manager, devrais I reinstal, and if so, how.

  I must have supported on uninstall by mistake.  How do reinstal this adapter.  My computer has not been performing how it should, I couldn't connect to the internet sometimes, or I couldn't open hotmail or some websites.

  Your help would be appreciated.  Thank you

  Hello

  I suggest to refer to this link and follow the instructions in the link below and check, if this can help:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/Microsoft-ISATAP-adapter-3-deleted/c3f00aa9-CA38-4419-85dB-1a8f165ab01d

  For more information, see this link:

  http://support.Microsoft.com/default.aspx?scid=KB; EN-US; 932520

  It will be useful.

• Microsoft isatap adapter

  the isatap map affect the use of anything? It's what should I do is there a yellow exclamation?

  ·                        ISATAP adapter:

  ·

  ·                        http://support.Microsoft.com/kb/932520

  On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message

  Windows cannot load driver (Code 31)

  You can ignore this error message. This error message does not indicate a problem with the adapter. The adapter will continue to function correctly.

  See you soon.

  Mick Murphy - Microsoft partner

• Windows #2 ISATAP adapter cannot load driver (code 31)

  Using Vista Home Premium, I get the following error message:

  "microsoft isatap adapter network adapt #2 windows cannot load driver (code 31).

  Because I can not connect to the internet, where can I get the correct driver.

  Hello

  Control Panel - devices - right click on - UNINSTALL - REBOOT Manager

  Nothing else to do, Windows will do the rest. And you can ignore the errors altogether if you want and
  on some computers, it will always be there but don't cause any trouble.

  On a Windows Vista-based computer or on a Windows Server 2008, Microsoft computer
  ISATAP map appears with a yellow exclamation next to it in Device Manager and you also
  error message
  http://support.Microsoft.com/kb/932520

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Problems with Isatap adapter and Wirelesss network.

  The system is a sony viao and it's a windows vista too. It is impossible to connect to the wireless network. I checked Device Manager and noticed that the map isatap #4 and #5 do not work properly. How can I solve this problem?

  Separated from the:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/Microsoft-ISATAP-adapter-4-not-working/ef9c6ad9-623e-416F-8D9F-8e3d83d998ca?page=2#LastReply

  Please start your own Thread in these Forums.

  You are replying to a Thread 2009; It comes to 2014.

  ________________________________________

  Read this, you can:

  "On a Windows Vista-based computer or on a computer Windows Server 2008, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message"

  http://support.Microsoft.com/kb/932520/en-us

  Windows cannot load driver (Code 31), etc.

  RESOLUTION

  You can ignore this error message. This error message does not indicate a problem with the adapter. The adapter will continue to function correctly.

  ____________________________________________

  You do not tell us the error your when you try to connect to the wireless network.

  We don't know if it's drivers or you have put in place correctly.

  Use the computer that you use to get here for access to the Sony site > downloads Section > key in your model number and operating system > find NETWORK card drivers > download and save > use copy to a flash drive and transfer and install them.u here to access the site on your computer or hardware manufacturer > downloads Section > key in your model number and operating system > finding drivers > download and save their > copy to a flash drive and transfer and install them.

  See you soon.

• Error code 31 MS ISATAP Adapter

  Not sure what happened, but I get this message error than MS ISATAP Adapter
  Device is not working properly. Windows cannot load the drive of the device so require.
  ROOT / * ISATAP/0000

  I went to MS and charged the driver, then he said I'm current and everything should be ok. However, in my device manager is always peripheral watch does not. I went to MS and then gave me three different websites to download additional programs to just a simple $30 and I can't correct the 19 drivers is said dysfunction is. I'm frustrated because I don't want to throw money at the problem. These programs say they are free but then I download the program to discover the questions and Yes, they are. However, now, it will cost money to register the product to RESOLVE the problem.

  Any suggestions to solve this problem would be greatly appreciated.

  Hi MonTQ,

  Welcome to the Microsoft Vista answers Forum!

  We receive the error code 31 if the device driver is not updated. As you have already updated the device try reinstalling the device driver and check if it works, if it does not resolve the problem, you can ignore the error message, link below will serve you more information related this topic:
   
  On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
  http://support.Microsoft.com/default.aspx/KB/932520
   
  Steps to uninstall and reinstall the device driver:
   
  Uninstall and reinstall the device in Device Manager. Steps to uninstall the device:
  i. click on start, type devmgmt.msc and then on enter.
  II. Locate the Microsoft ISATAP Adapter device
  III. right click on the device and select uninstall
  IV. restart the computer to make the changes happen
   
  Uninstall and reinstall the card program and features. Steps to follow
  i. Click Start and select Control Panel
  II. in the Control Panel double-click the "Programs and features" icon
  III. here you can find all the programs and items that are installed in Windows Vista.
  IV. to remove the adapter click once on the program and then click Uninstall/change, and follow the prompts.
   
  Hope this information is useful.

  Let me know if it worked.
  All the best!
   
  Thank you, and in what concerns:
  Samhrutha G S - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Can someone help me with the following: using Vista - ISATAP Adapter #3 works not - (code 31)

  I got nothing else problems with windows update (I use Vista home edition), and now I have the following:

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Device Type Microsoft ISATAP Adapter #3 device peripheral status does not work correctly. Windows cannot load the required device drivers. (Code 31) Plug - and - Play ID ROOT\ * ISATAP\0002

  I would really appreciate the help.

  Thank you
  Karen

  Hello

  You can ignore this error message. This error message does not indicate a problem with the adapter. The adapter will continue to function correctly.

  http://support.Microsoft.com/kb/932520/en-us

  See you soon.

• I tried to update my driver for the ISATAP adapter and I uninstalled it, where can I go to reinstall this material?

  I uninstalled ISATAP card and I need to find so I can reinstall, please help.  Thank you

  See this link:

  ISATAP #3 card has a driver problem
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/ISATAP-adapter-3-has-a-driver-problem/a7e51ba1-604b-4FA6-B612-d8b3009fe1ee

• Update__Microsoft ISATAP adapter #5 is available message

  "After boot, there is a message' Update__Microsoft ISATAP adapter #5 is available".__I click the update, and then a message"Update/Installation not successful ' poped upward.

  I have two questions:

  1. What is Microsoft ISATAP adapter #5?

  2. How do install, if necessary?

  Thank you

  Hello

  Control Panel - Manager of devices - right click - UNINSTALL - REBOOT

  Nothing else to do, Windows will do the rest. And you can ignore the errors altogether if you wish
  and on some computers, it will always be there but don't cause any trouble.

  On a Windows Vista-based computer or on a Windows Server 2008, Microsoft computer
  ISATAP map appears with a yellow exclamation next to it in Device Manager and you also
  error message
  http://support.Microsoft.com/kb/932520

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.