ISE wireless with HP basic switch

Similar Questions

• ISE works with Local Mode switch

  Hi guys,.

  My AP is configured to run as a mode with my WLC Flexconnect, which means that my wireless data will be locally switched without going through my WLC, is this ok for my ISE to controll my Wi - Fi?

  Kind regards

  Yes; FlexConnect supports authentication central both locally and centrally switched traffic patterns.

  Lots of info on FlexConnect here;

  http://www.Cisco.com/en/us/docs/wireless/controller/7.4/configuration/guides/Flexconnect/config_flexconnect_chapter_01.html

• Unable to connect wireless with Photosmart 2510

  I just upgraded my router from G to N.  I have a Linksys WRT10N.  My network is secured with WPA-Personal.  Since I upgraded from G to N and WEP to WPA, I'm unable to get my 2510 Photosmart to connect to the wireless network.  Initially, I was in WPA2 and downgraded my network to WPA with on security a bit of luck.  I entered all encriptación WPA data in the web browser integrated prior to installation.  I tried to install it several times and everything seems to go through OK but the blue light on the cover of never turns on again when the ethernet cable is disconnected.  When I run the network config. page it says "scanning" status of wireless.

  I talked to Linksys and they told me that the network N should work down to a B network printer.  Does anyone have any suggestions?

  Thank you!

  Hi Kim,

  All printers inkjet wireless HP since 2004 supports WPA - PSK and WPA2-PSK.  All new HP inkjet will certainly support WPA - PSK and WPA2-PSK.

  I'm more familiar with the WRT54G, but the WAPG works as well.  Here is how to convert the WRT54G in a simple access point:

  1. Connect LAN port of the WRT54G #1 and open the web without wire-router page (it should be 192.168.0.1 or 192.168.1.1)
  2. Go to the wireless section of basic wireless settings.  Create a new SSID and choose a channel without overlap, which differs from the WRT160N.  In North America, the overlapping channels are 1, 6, and 11.  Press to save the changes.
  3. Go to the wireless security section and the configuration up to WEP.  Press to save the changes.
  4. Return to the configuration page.  Disable the DHCP server and set the router IP address to something other than then the address IP of WRT160N.  For example, if the WRT160N IP address is 192.168.0.1, and then set the WRT54G to 192.168.0.201.  Make sure that the first three groups of numbers of the IP address are the same.  Press to save the changes.
  5. Now, connect an Ethernet cable between WRT54G #1 LAN port and one LAN of the WRT160N ports.

• Unable to connect to my router wirelessly with Dell D410 running XP Pro using the pro/wireless 2915ABG card.

  I got the latest drivers, downloaded the last utility connection for the wireless card config, then switched back to wireless zero configuration.  All to nothing does not.  I use a router Netgear MR814 with WEP, which works very well with all my other wireless devices.  Have checked and rechecked the WEP key to make sure it was OK. And I even disabled access on the router control.  Everything seems to be correctly set, but whenever I try to connect, it is not.  Someone at - it any other ideas?  It would be very grateful.

  Hello

  1. do you have this setup already worked successfully?
  2. have you made changes on the computer recently?
  3. do you get an error message?

  Check to see if the problem exists in the boot. Configure the computer to start start clean and then 50-50 approach use to check, with which application, these files are associated with. Once you find the application I would ask you to uninstall and reinstall.

  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

  We can also try to reinstall the WIRELESS drivers from the Dell website and check.

  I hope this helps.

• Windows 8 homegroup via wireless with Security Windows 7 computer password warning

  At first I apologize for being so inept, but I do not understand how computers communicate with each other.
  Never have and it frustrates me no end. I don't know that I do what infinitely more complicated than it really is.

  I have two computers, Windows 8, Windows 7, and I want to share/move files between them.
  As I understand it, this means that none of the standard XP compatibility problems are involved.
  I got the different residential group folders and pages so I don't know where they are and what they are asking.
  Both computers come with their name on each of the other networks on libraries, etc., framed in folders.
  Windows 8 has a homegroup computer put in place with its files to share.
  Windows 7 sees this homegroup, so I'm sure I'm OK with the basic plan.

  If I click on the symbol of the other computer under the sign of the network on one or the other, I get ask username and password of Windows security.
  What user name and password, they are referring to?
  The password created for me in the homegroup section?
  Is the user name that I just create or should it be the name of the computer?
  Is the name and the password for my router wireless never involved?
  I would like to be the main computer of Windows 8, but I must have each computer to join the other homegroup

  I also have a group of work involved on the Windows 8, generically named Workgroup.
  When I go to the systems to confirm or change the name of the computer, if I select the Working Group, I get the following:
  You cannot join a computer to a domain running from this edition of Windows 8.
  Two computers, when I get quick security, yet have a domain name.
  Should I worry about this?
  The Working Group will be distinct from the Homegroup if I set up one for work?

  Again, I apologize for my inability to grasp some of these things.
  Believe me, nobody likes less than me.

  Hello

  I want to tell you that you can try to enter the username and password created in the homegroup and the audit section.

  You can create a homegroup on one computer and what to do as the master computer and make other computers to join the homegroup.

  I suggest you check out these links for more information about homegroup.

   
  Why can't I connect to other computers?
  http://Windows.Microsoft.com/en-in/Windows-8/cant-connect-other-PCs
   
  Where can I find my homegroup password?
  http://Windows.Microsoft.com/en-in/Windows7/where-can-i-find-my-HomeGroup-password
   
  Homegroup from start to finish
  http://Windows.Microsoft.com/en-in/Windows/HomeGroup-help#HomeGroup-start-to-finish=Windows-7&V1H=win8tab1&V2H=win7tab1
   
  Hope that answers your query.

• My Ipad air2 does not start.  Tried hold it together switch with on/off switch.  Apple logo appears for about 15 seconds and then turns off again.

  My Ipad air2 does not start.  Tried hold it together switch with on/off switch.  Apple logo appears for about 15 seconds and then turns off again.

  Is there another way to start the IPAD?

  Try the steps here:

  https://support.Apple.com/en-us/HT201412

• iPhone 6s doesn't sync wirelessly with iTunes

  I have a new iPhone running OS 9.2.1 6s.

  Is set upward wireless at the Apple store, restored from my previous iPhone 5 and me kept updated iOS and phone saved wireless, and had not annexed it with iTunes on my Mac, until today.

  I have the gasket with the USB cable into my iMac running the last El Capitan, iTunes 12.3.2

  The iPhone has shown in the section "My devices" in iTunes, but I immediately got a message "there is a new version of iOS for the iPhone (9.2.1). iTunes started download iOS 9.2.1 but I stopped, because the phone has already 9.2.1.

  I checked the preferences to allow the iPhone to sync wirelessly with iTunes, applied and then ejected from the iPhone.

  My iPhone is connected to wifi, but when I restarted iTunes it does not connect wireless - the wireless only showing in iTunes is my iPad.

  My questions are so

  (1) why only iTunes can only see my iPhone 6 is already running the latest version of the iOS software

  and

  (2) why didn't it connects wireless when I set the preference to do?

  Thought I'd ask advice here before that I contacted Apple support.

  Thank you

  Caroline

  There is a different verson of 9.2.1 released by Apple to fix the error 'January 1, 1970.  It is only available through iTunes, not live.

• Can not put on wireless with FN + F8 on my Satellite L750D - 19 c

  Hello

  I can't put on wireless with FN + F8 on my Satellite L750D - 19 c with windows 7. It stopped work at shot, and I cant get it up and running again. I tried to install the latest drivers and the disabled option 'save energy '.

  / Magnus

  Hello

  I have the same problem with my satellite L670.

  The FN keys do not work and I am not able to use my Internet connection. : () o

  I used to get these buttons to apear on the top of my screen to get the mouse towards the edge.

  So I could turn the wireless on / off power with the mouse.

  But these "maps" doesn't apear. Or my settings on the camera to the left of the screen.

  Thank you very much.

  Post edited by: PearlSabian

• HP all-in-one wireless with 10 5525 windows insider

  Hello world

  I work with the 5525 printer about 3 years.

  also with wifi wireless, andalso with windows 10.

  all of this until last May.

  in may, I was to format and install windows 10 insider and fromthis point, thast all I tried to solve the problem, it's not helping me. and the problem is:

  that, since may, I can't work with this printer, wireless, with wifi.

  I can to work very well with a usb cable, but not with the wireless.

  Windows don't simply do not see and not detected my impression when I try to work wireless.

  is not see the printer. not even in offline mode.

  in the list of wifi, I can see the HP-printing-da-Office-5525, but in the unit and the printer - no.

  I also tried to install all the latest drivers from hp and for windows 10 - without resluts.

  also, I tried to install the latest windows build - 14390, but this does not help me.

  I think its something with the drivers.

  can someone help me?

  Thank you very much!

  Well, first thing to do is to disable wireless live, because you don't need and it's confusing questions. To disable this feature:

  1. On the printer, click on the wireless icon that looks like a radio tower.
  2. Click settings.
  3. Click on wireless Direct.
  4. Click turn OFF.

  Now, to connect the printer to your wireless network:

  1. From the main screen, click on the wireless icon.
  2. Click settings.
  3. Click Wireless Setup Wizard.

  Please let me know the results after following the above. If you are able to connect to the wireless printer, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• "Several times I am receving the dialog box with" visual basic command-line compiler.

  "Several times I am receving the dialog box with" visual basic command-line compiler.

  Hello

  1. This occurs when you use a specific application or all applications?

  2 did you a recent software or changes to the material on the computer?

  3. have you installed all versions of Visual studio?

  4. What is the finished message, that you have found?

  You can try to perform a clean boot and see if it helps.

  A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  After the troubleshooting steps, please refer to clean the boot link to put the computer to normal startup mode.

  Hope this information is useful.

• Using Windows XP with an access switched. How can I stop the network Dialer to invite the user connect even if I checked never dial a connection in Control Panel, then apply, then OK?

  Using Windows XP with an access switched. How can I prevent the network Dialer to invite the user connect even if I checked: never establish a connection to the Control Panel, then apply, then OK? She comes right back in a few minutes for: always connect by default. Help! Control panel Connections tab doesn't really seem to apply my change to never establish a connection right back to always make the default connection. What else is there to do?

  Hi Richard,

  You did it all change hardware or software on your computer before this problem?

  You can follow this link & check if the problem persists:

  Network connections and remote access troubleshooting

  Hope the helps of information.

• I can't connect to the network wirelessly with my Emachines eM350 portable because I get the automatic Wireless Configuration error, see Article 871122.

  original title: WiFi

  I can't connect to the network wirelessly with my Emachines eM350 portable because I get the automatic Wireless Configuration error, see Article 871122.

  I use a Huawei E585. I simply want to clamp it alll in the tray.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  (1) make sure that u run "NET START WZCSVC" on the command-line as soon as u Ouvrezunesession WINDOWS XP (START, RUN, NET START WZCSVC (command line)).

  (2) START, CONNECT, WIRELESS INTERNET CONNECTION

  --> under the 'GÉNÉRAL' tab: (1) right click on the wireless Internet connection; (2) click on properties; (3) make sure that all THE ELEMENTS under the title "THIS CONNECTION USES THE FOLLOWING ITEMS" are COMPLETELY FUNCTIONAL, i.e. UNCHECK THE ONES THAT DO ARE NOT ACTIVE ~!  (I recently turned off AVG and that this item has been inadvertently clicked on ~!) ;

  --> on the 'ADVANCED' tab: run the NETWORK CONFIGURATION WIZARD to reset your network

  3) http://support.microsoft.com/kb/871122 --> RUN 'DIFFICULTY CE PROBLEM' (ms - fix 50469)

• I can't connect to the network wirelessly with my Dell INSPIRON laptop because I get the automatic Wireless Configuration error, see Article 871122

  I can't connect to the network wirelessly with my Dell INSPIRON laptop because I get the automatic Wireless Configuration error, see Article 871122

  Try this below and see if it help you.

  http://support.Microsoft.com/kb/871122

• Print Spooler service is not running (could not install printer) hp photosmart wireless with

  Print Spooler service is not running (unable to install printer) hp photosmart with wirelessprint spooler service does not not (impossible to install printer) hp photosmart wireless with

  Hello

  · What is the model number of the computer?

  Try not the link below and check if it helps: you encounter printing problems, display the printer icons and adding printers, the print spooler service does not work correctly and you receive error messages related to printing on a Windows XP computer: http://support.microsoft.com/kb/919750

  You cannot print and you receive the error message "Spooler subsystem app has encountered a problem and needs to close": http://support.microsoft.com/kb/810894

• How can I configure my printer HP Deskjet f4400 to print wirelessly with my Mac osx?

  I am able to print entirely specific wireless with this printer or do I connect to the computer via the usb cord or router when I want to print?

  Thanks Jabzi!